Cannot fax after 10.5.7 update

When I try to fax after the 10.5.7 update using the external modem the process stops with saying "preparing fax ..." and the fax marked as used in the print & Fax. The modem reacts on calls from the outside. When I put the modem on my laptop with 10.5.6 I can still send a fax with it.
Any idea? (I reset already the print system and reinstalled the fax)

Refer to John Scott6's post about how to temporarily work around this faxing issue:
http://discussions.apple.com/thread.jspa?threadID=1971435&tstart=15
It is true that as of now the faxing protocol is broken and you cannot send a fax when listening for a faxed to be received at the same time. You must stop listening for faxes by un-checking the "receive faxes on this computer" box in the fax/external modem preferences under Receive Options. You can then send a fax regularly. Then, when you are finished sending your faxes, you will need to re-check the "receive faxes on this computer" box in order to automatically listen for and receive incoming faxes.
Hope that helps.

Similar Messages

  • Cannot Login After 10.4.8 Update!

    I just updated my Powerbook G4 Titanium to 10.4.8, and I can no longer login to my computer. My password uses normal characters, and when I enter it, the login screen disappears (as if the finder was going to load), and then it suddenly REAPPEARS, prompting me for the passoword again. I am 100% certain that my passoword is correct, because when I attempt to enter something else, it merely shakes and re-prompts me on the spot. Any ideas, anyone? I have attempted to start-up in safe-mode, single-user mode, and from a Software Restore CD, but unfortunately I cannot. Does this mean that I have open-firmware running on my system? Any and all advice appreciated,
    -Gideon
    Powerbook Ti 550MHz Gigabit Ethernet   Mac OS X (10.4.8)   120 GB HD, 1 GB RAM, Superdrive [1x]

    Hi, Gideon.
    1. Have you verified that the Caps Lock key is not enabled? Any symbols appearing in the right side of the password entry field?
    2. You wrote: " I have attempted to start-up in safe-mode, single-user mode, and from a Software Restore CD, but unfortunately I cannot."I'm trying to put your statement here in context with the password/login problem. Are you saying that (a) you cannot log in when you start up your Mac in these other modes or (b) that you simply cannot start up your Mac in these other modes?2.1. If (a), An errant Startup Item maybe the cause. My "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem: focus on the testing of Startup Items.
    2.2. If (b), then I suggest you:2.2.1. Run at least steps 1-3 of the Procedure outlined in my "Resolving Disk, Permission, and Cache Corruption" FAQ. You may be getting the timing a bit off in terms of holding the C key to startup from your Tiger install disc.
    2.2.2. Run the Apple Hardware Test (AHT) that came the affected computer. See my "Apple Hardware Test" FAQ for comprehensive advice on using the AHT in troubleshooting.
    3. If your account is the only account on that computer, then your account is also the Admin account. See "Mac OS X 10.4 Help: Changing your administrator password."
    4. re: Open Firmware: If you've enabled Open Firmware, you should see the image noted in "Setting up firmware password protection in Mac OS X 10.1 or later" when you attempt to startup from the install CD.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X
    Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • IChat Service Cannot Start after 10.6.6 Updates

    Hi,
    My Mac Mini Server was working perfectly until I updated 10.6.6. All services are running except the iChat service. There is a series of error message in the log.
    Any help? I have been searching everywhere but cannot find any solutions.
    Thanks in advance.

    Hi Tim,
    I have a look at the topic "cannot log into iChat" post but this is not related to mine. My problem is very similar to some of the topics posted like "iChat server issues".
    I have actually reinstall the whole server again. Checked all the services are running well (including the iChat service). Then, I run the Software Updates and the system updated with 10.6.6. Then, I restarted the server and the iChat service stopped now. The rest of the services are still running ok.
    I suspect the 10.6.6 update has changed something and cause the service to stop.
    Hope the information is sufficient. Thanks in advance.

  • Cannot boot after 10.7.5 update (MacPro1,1 mid-2006)

    I have tried to do the update on my MacPro for the last few weeks.  Each time, it fails and after reboot, it goes into the Apple Utilty boot.  At that time, I need to restore a backup from my time machine.  I checked for RAID, and under system report, there is no RAID in the MacPro.
    "This system doesn't contain any supported hardware RAID devices. If you installed hardware RAID devices, make sure you installed them properly."
    What else do I need to do in order to get this update to work?  The computer is almost seven years old and is out of warranty and extended warranty.

    format a disk drive and do a clean install of Lion.
    And buy a copy of carbon copy cloner and start using that...
    Using Cloning as a Backup Strategy
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    http://www.bombich.com/software/updates/ccc-3.5.html
    OS X Lion Install to Different Drive
    How to create an OS X Lion installation disc MacFixIt
    Migration Assistant Update for Mac OS X Snow Leopard
    http://www.apple.com/support/lion/installrecovery/
    Create an OS X Lion Install disc
    http://reviews.cnet.com/8301-13727_7-20080989-263/how-to-create-an-os-x-lion-ins tallation-disc
    How to clone your system:
    http://macperformanceguide.com/Mac-HowToClone-backup.html
    http://macperformanceguide.com/Mac-HowToClone.html
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    http://www.macperformanceguide.com/blog/2012/20120711_2-MacPro-internal-clone-ba ckup.html
    General purpose Mac troubleshooting guide: Isolating issues in Mac OS X
    Creating a temporary user to isolate user-specific problems: Isolating an issue by using another user account
    Identifying resource hogs and other tips: Using Activity Monitor to read System Memory and determine how much RAM is being used
    Starting the computer in "safe mode": Mac OS X: What is Safe Boot, Safe Mode?
    To identify potential hardware problems: Apple Hardware Test
    General Mac maintenance: Tips to keep your Mac in top form

  • BB Z10 cannot charge after the 10.3.1 update

    Hi
    I am having problem with my phone that cannot charge after the battery drained (Updated with 10.3.1). When I charge the phone, the LED will turn red, then the Blackberry logo appears and lastly the red battery logo appears telling me that the phone has no power. It keeps repeated many times.
    How to boot the phone?
    Please help me. Thank you.
    Solved!
    Go to Solution.

    I suggest you try the very clean and very forceful AutoLoader method:
    http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
    Beware that it is completely destructive...the device will be "like new"...no data, no apps, no accounts, etc. Be sure you take a full backup first, as well as make full manual documentation of all apps, accounts, configurations, etc. Sometimes a restore reintroduces the very corruption one is trying to eliminate, and manual reconfiguration is necessary.
    You can also use this to fall back to a prior OS if you desire...you can install any OS level for which you can find an AutoLoader. (Hint...search over on the CB site!)
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • When trying to update apps an invalid apple id show up and I cannot get the apple id to update to the same id,  I have restored, restored as a new phone, I have been into the manage I am at wits end after 7 hours on hold and working with techs.

    When trying to update apps an invalid apple id show up and I cannot get the apple id to update to the same id,  I have restored, restored as a new phone, I have been into the manage I am at wits end after 7 hours on hold and working with techs.

    Finally got through to tech support and found someone who seemed to know what was going on, he walked me through and using appleid.applesupport got me to a point where i could get a new password for the apple id that kept showing up. 
    I think you were on the right trail and I want to say thanks for your help.  Much appreciated
    ccl43

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • I have been using facetime on my iphone for a while and after the recent, ios update, I cannot seem to use the facetime. What went wrong?

    I have been using facetime on my iphone5 for a while and after the recent IOS update, I cannot seems to use my facetime any longer. what went wrong?

    'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
    That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
    XP instructions in the following document: How to perform disk error checking in Windows XP
    Vista instructions in the following document: Check your hard disk for errors
    Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
    Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
    Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

  • HT2500 After my last software update I can no longer access my mail.  message displayed says "you have mail version 4.5 this cannot be used on  Mac OS X Version 10.6.8 .  How do I fix this???

    After my last software update I can no longer access my mail.  message displayed says "you have mail version 4.5 this cannot be used on  Mac OS X Version 10.6.8 .  How do I fix this???

    See possible fixes here.
    https://discussions.apple.com/message/19760703#19760703
    https://discussions.apple.com/thread/4311280?tstart=0
    https://discussions.apple.com/message/19710911#19710911
    Some have reported success simply by reinstalling the update.
    http://support.apple.com/kb/DL1586
    Or download and apply, or reapply, the 10.6.8 Combo update first, then apply the Security Update again.
    http://support.apple.com/kb/DL1399
    I'd suggest starting with the simplest of these fixes, so look them over first.

  • Failure: Cannot login after Lion 10.7.2 update

    I cannot login after performming the update realeased today.
    After boot, at the login screen, I see the user in the circles. Upon selecting a user, entering the password, the spinning circle below the Apple appears. It spins for a few mnutes, then return with a NOT symbol as the spinner contues to spin endlessly. After a while, the fan kicks into overdrive.
    I tried to do the boot in recovery, start terminal, resetpassword, restart, login as root steps, but do not see an option to login as root upong restart - just the User circle icon.

    I have a similar problem, but it looks like I have solved it.
    I rebooted holding down ommand-R to get to the recovery-HD mode.  From there I chose the options to re-install Lyon (requires internett access because it downloads a new copy). 
    Since I have multiple disks attached (the internal and a bootable backup drive) it asked which disk I wanted to use.  When I chose the internal drive it told me it was locked and asked for the FileVault unlock code.  After that things seemed to proceed properly.
    I suspect that the problem is in some way tied to my use of FileVault.

  • After download a new update I cannot FaceTime

    I cannot communicate with Face time with my friend who has iPAd 2 after downloading a new update from 18/07.

    Howdy Inessazhk,
    I found this article while researching FaceTime for you named FaceTime for Mac: Troubleshooting FaceTime found here http://support.apple.com/kb/ts4185
    Troubleshooting FaceTime for Mac
    You can make FaceTime calls using the FaceTime app. You can call FaceTime users whose contact information is in Contacts. You can add contacts and edit contact information in either FaceTime or Contacts. To place a video call, you may use a phone number or email address.
    If you encounter issues making or receiving FaceTime calls, try the following:
    Verify that FaceTime is enabled in FaceTime > Preferences.If the issue persists, or if you see the message "Waiting for Activation", try toggling FaceTime off and then on.
    Verify that the Date, Time, and Time Zone are set correctly:
    From the Apple () menu, choose System Preferences > Date & Time > Date & Time.
    Enable "Set Automatically".
    Click the Time Zone tab and confirm the closest city is correct.
    Verify that both parties are connected to an active broadband Internet connection.
    See Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection.
    Consult Using FaceTime behind a firewall for necessary ports to open in firewalls, security software and routers.
    If you encounter issues using a Wi-Fi network, use standard Wi-Fi network troubleshooting to resolve interference and other issues.
    Verify the phone number or email address being used is the correct one activated for FaceTime.You can verify that you are using a valid Apple ID at appleid.apple.com. You can also create an Apple ID or reset your password from this website.
    Verify that both parties have installed the latest software updates for their Mac and/or device. See:
    Mac OS X: Updating your software
    iOS: How to update your iPhone, iPad, or iPod touch
    All the very best,
    Sterling

  • After installing lion and updating to pages 4.1 cannot view my document content after I open the document.  Shows how many pages I have and how many words in word count, but no words...

    after installing lion and updating to pages 4.1 cannot view my document content after I open the document.  Shows how many pages I have and how many words in word count, but no words...

    Same problem. Tried reinstalling Pages. Didn't help. The behavior is like I am typing with a white font on a white background, but I am not.

  • After 10.7.2.update cannot see SD card reader in usb drive. Used to appear on desktop and start iPhoto but now nothing happens. It is recognised by system profiler (usb hub), but cannot find it anywhere.

    After 10.7.2. update cannot see SD card reader in usb drive. Used to appear on desktop and start iPhoto but now nothing happens. It is recognised by system profiler (usb hub), but cannot find it anywhere. Any ideas?

    Zap the PRAM and Reset the SMC, then try again.

  • Cannot open gh2 rw2 files after 10.7.4 update

    I'm having trouble opening Panasonic GH2 raw (.rw2) files after 10.7.4 update. I cannot view them in quick view or open them in Preview.
    I verfied on a another Mac running 10.7.3 - works fine; and then immediately after 10.7.4 update it does not work.
    Any remedies?

    I started a similar thread (before I noticed this one), and someone replied by pointing me to the helpful thread:
    https://discussions.apple.com/thread/3942768?start=30&tstart=0
    I tried the suggestion, and it fixed the problem for me.
    You need to execute this command in the terminal (and I believe you may need to do it separately for each user on your computer):
    /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/LaunchSe rvices.framework/Versions/A/Support/lsregister -R /System/Library/CoreServices/CoreTypes.bundle/Contents/Library
    I'm not sure how the above command gets formatted, but make sure that it is all one command and that there are only spaces before and after the "-R"
    If you want to understand what the above command does, check out the thread I linked to.

  • My iPhone 5 64g cannot on after update latest ios from 8.2 to 8.3

    My iPhone5 64g cannot on after update latest ios 8.2 to 8.3

    Thanks for the quick response ,
    it did help alot and now the iphone works much much better and faster.
    can you please try to figure out how to fix the messages search so it work fine
    its give me now result maximum up to 3 days old
    thanks friend

Maybe you are looking for

  • Calculate the total value of payments with the procedures and triggers?

    Hello! I work for a college project and I have a big problem because professor requires to do it by the examples he gives during the lecture. Here's an example that should be applied to its base, so please help! I have three table with that should wo

  • My itunes wont work for my itouch

    i just got a new computer for christmas, and my old one crashed, so i got a software that took all my songs off my ipod and saved them to my computer, i installed itunes and when i plugged it in it would not reconize it as my itouches main computer,

  • PDFs black after Adobe Reader upgrade

    I've just upgraded to Adobe Reader 10. This works with IE and Chrome but FF shows black screen and spinner on tab for ever. I have read your comprehensive help screen and confirmed all the items in there are up to date. I did not have this problem, n

  • Problem photographing score to PDF file

    Hi, I'm currently having a major problem photographing my score in logic pro 8. It will only recognize the first page. Even when I try to shoot individual pages, the only page that can be viewed in PDF format is the first. Can someone point me in the

  • JSF compatibility

    Hello. I am just getting started with JSF and I only have J2SE1.4 and Tomcat 4.1 installed. I would like to know which version of JSTL and JSF would work with that? I downloaded the 1.2 version from https://javaserverfaces.dev.java.net Would that be