Cannot Find WiFi router

Just moved into new flat & though my Ipod touch can see the flat's wifi & connect, my Ibook running 10.4.11 cannot though it can see all my neighbours. Is there anything I can try. I have searched for the network name with the WEP passcode but it can still not find it. Any help would be much appreciated.

I just had this type of problem with my Linksys router. I pressed the reset button on the router and it erased my set up info (bad move). I contacted Linkys support chat and learned that I had to run through the online set-up procedure again. Now my iBook sees the router.
I don't want to send you on a wild goose chase but maybe all you need to do is set up your connection again.
Randy

Similar Messages

  • PC cannot find wired router wrt54g2

    I recently bought a new computer and wired it to the router and it worked fine. Since then I have replaced vista with xp, now when try to configure the router it says "cannot find wired router" in both LELA and when I try to setup from the disc.

    When you replaces the OS on your Computer, make sure the Ethernet Drivers are installed on your Computer. When your computer is Hardwird to the Router are you able to access Internet on  your Computer?
    Click on Start - Control Pannel - Network Connection - in this window check if you are able to see "Local Area Connection", Right click on it and click on Status and click on the Support tab, below it will display you the IP address. Check whats the IP address your computer is getting it from the Router, it should be 192.168.1.xxx.
    If you are trying to configure your router using the setup disk, you can exit from the setup and configure all the settings on your Router manually..
    If your Internet Service Providor is Cable follow this link
    If your Internet Service Providor is DSL follow this link

  • HT1695 cannot find "wifi" on my ipad

    I have an Ipad mini. My router is a linksys. Itunes says to sync my ipad with itunes but i cannot find the wifi tab on my ipad mini

    Click on the Settings icon.
    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Cannot find wifi connection anymore

    I purchased my iphone this past March and everything has been working fine until now. Last Thursday I was on wifi downloading an app that was about 12MB. After making the purchase, I was disconnected from wifi and could not proceed with the download.
    I continually tried connecting, but could not find the network. It is now Monday and after resetting the network settings, trying the airplane mode trick, updating to the latest version, and restoring I still cannot find the network. I've tried on multiple networks too and still no luck. I tried phoning Tech Support but they said I'd have to pay for phone support. Any suggestions? hardware problem? Have no idea who to send it to if needing replacement. No Apple store near by either.

    So I have two iphones (3G and 3GS) in the family, an ipod touch (1st gen), an IMAC, AppleTV, MAC Book and a MAC Book Pro. An new dual band Apple Airport Extreme and dual Apple Airport Extreme.
    The computers & Apple TV connect just find to my network (security is WPA/WPA Personal). The iphones and ipod touch cannot connect worth a hoot. My neighbor has a Belkin network (no security) and both phones and touch connect just fine. I am totally flummoxed. I have tried resetting the network settings on the iphones but to no avail. The only time the devices connect is when the phone or touch is literally within a foot of the base station.
    any suggestions?

  • Playbook cannot find WIFI networks

    Hi, I have a new Playbook 16gb wifi and the wifi isn't working. Essentially what happened was after I completed the initial setup it prompted me to install an OS update after which the WIFI stopped working. I cannot connect to any network no matter the type a/b/g/n, the frequency, the channel or the mode. I have tried on two Netgear routers, 1 DLink and 1 iPhone (used as a hot spot). I have tried PBS using the actual button and the PIN but neither works. It just cannot find any networks. 
    I tried resetting to factory defaults but that has made the situation worse because I am now stuck at the setup screen with no networks to complete setup. I can't connect to the desktop software either because the installation hasn't completed.
    Any suggestions would be greatly appreciated.
    Cheers
    David

    Hello
    Were you able to fix the wifi issue ?
    I have successfully reloaded QNX OS on the Playbook using Desktop manager.
    Version 1.0.7.2942 was loaded.
    I still have the same problem, it is impossible to connect to the wifi network.
    I have tried wpa2, wpa and wep , nothing works. I have tried at over 10 different routers.  I tried with routers where other playbook wifi works well, but this one playbook won't connect, I always get the same error while trying to pair to the network, it doesn't event get to the acquiring IP address phase.
    Thanks

  • Cannot find wifi-menu command

    I have a lenovo T430 laptop.   
    I made my usb stick into a bootable medium using YUMI.
    Then I boot into arch linux 2013.05.01 from usb. 
    But I simply cannot find the wifi-menu command. 
    So what might be the reason for this ?  Thanks a lot

    https://bbs.archlinux.org/viewtopic.php?id=162725

  • Suddenly I cannot find wifi on iphone 4s

    I have an iPhone 4s with iOS 8.1.2.
    I find myself abroad for a month. I have been using my iPhone normally for three weeks without any trouble. Suddenly yesterday, after having worked with it for several hours, it cannot find anymore the wifi of the place in which I am staying, even if all other people can still use it.
    I already tried to disable the location setting and also to reset the original settings. None of these have produced any results. Can you help me?

    Hi ff/medic,
    To browse your music by playlist, look at the bottom of the screen in the Music app, you should see a Playlists button to click. If not, select the More… button.
    You can find this and much more information in the iPhone’s User Guide -
    iPhone User Guide
    http://manuals.info.apple.com/MANUALS/1000/MA1565/en_US/iphone_user_guide.pdf
    Thanks for using Apple Support Communities.
    Best,
    Brett L

  • Cannot find wifi after restoring

    After restoring my ipad, it cannot scan for wireless networks.  What should I try?

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Cannot find wifi

    My brother and I got new Ipod touches for christmas - and they cannot detect the wifi in the house, despite the fact that all the laptops are running fine on it.
    They have picked up the prescence of other networks, and resetting the wireless connections/ manually entering the information in 'other' hasn't worked.
    We're using a Belkin N F5D8636uk-4 V1 router, on tesco broadband, set to broadcast ssid. I've tried about everything I can think of including updating firmware (there was no update avaliable) and restarting the router, switching off security, changing all the settings, nothing has helped and this is driving me to distraction - such a shiny new toy, and I can't use half the applications. ^^;;; Please, please help!

    Okay - the problem now appears to have been resolved. After setting up the network to use my brother's laptop (vista) as the router, turning it off made the wifi return to being broadcast by the router - but with the settings he had set on his computer, with the new ssid and password, and now we can both pick it up.
    ...this may be the first instance of vista managing to fix a problem? XD;;;
    Still, having gone through the settings, I have NO IDEA what has changed to make this possible! Everything looks the same - it's still set to b&g*n (There is no option for just a b&g network, btw. g only, n only, or all three. Changing between them earlier made no difference.).
    The only difference apart from a new name and key seems to be that the SSID now has no space in it. Which seems a silly thing to have caused ANY issue, but at this point I have no other ideas. ^^;; If anyone has an idea what was up, I would be very obliged, in case it happens again!

  • HT204051 iphone 4 cannot find wifi

    My iphone 4 will not find my home wifi. My wife's ipad and iphone5C do however. My phone will also find other networks just not my own. I have reset everything on my phone and router but still no luck. I have a Linksys E2500. Any ideas

    @dchmielowski
    First thing I want ask you, have you view the link below to troubleshoot your current issue:
    If your iPhone, iPad, or iPod touch won’t connect to a Wi-Fi network - Apple Support
    If yes and it was unsuccessful then I would reach out to Linksys and check the router firmware.  Chances are it maybe be running an outdated firmware.  Please call the numbers below to move forward.
    Customer service: 1 (800) 546-5797
    Technical support: 1 (800) 326-7114

  • SBS 2008 cannot find local router after router is changed

    Hello,
    I changed the router on my SBS 2008 server. Because I wanted more speed anticipating increasing cloud demands for bandwidth (my ISP provides 100 MB and earlier router chokes @ 48MB), I thought my network would be faster if I used the router to provide DHCP
    since SBS only supports 1 NIC.
    That was a big mistake.
    So I disabled DHCP on the new router and tried to use the Fix My Network Wizard to "fix my network".
    The results are very strange.
    I got all the messages about opening ports discussed elsewhere on this forum. But that's not the strange part.
    When I run the connect to the internet wizard , it reports that it found the router and provides the correct IP addresses for both it and the server. However, it did not find my new router at all. Instead, it finds the ISP's router
    which, of course, it cannot configure. (How it picked the correct IP addresses is also beyond me.)
    The router is a NetGear SRX.... I reset it to factory, disabled DHCP and assigned the fixed IP and DNS server information for our ISP.
    Does anybody have any idea why this new router cannot be found and how to fix it.(I have read all the similar posts but none apply.)
    Thanks.
    Murray
    M Whipps

    Sounds funky, let's go back to basic and start from fresh. Try performing these steps in exact order.
    1. Disconnect all Ethernet cables from new router
    2. Reset the router to factory defaults, usually with a paperclip tip, check manual
    3. Connect a computer to one of the LAN ports, do not use the server
    4. Configure the computer's IP address, if needed, to coincide with router
    5. Log into router and configure LAN IP to match your old router's LAN IP
    6. Disable DHCP Server in the router
    7. Disconnect computer from LAN port
    8. Connect Server to LAN port
    9. As a test, you should now be able to login into router, from the server, do not make any changes
    10. Re-run the Connect to Internet Wizard
    11. The wizard may not be able to configure the firewall, that is ok, you can manually do it later
    12. Once Wizard finishes, connect ISP to the WAN/Internet port
    13. Log into router and configure the internet connection
    you should now have internet going now on the rest of the network.

  • Cannot find Wifi driver in use

    Hi! I am creating a wifi-hotspot using Create_ap script https://github.com/oblique/create_ap. Strangely I cannot get it working. I use broadcom-wl from the AUR https://aur.archlinux.org/packages/broadcom-wl/ and I am passing --driver args with 'wl'. Please help!
    Thanks!

    Gusar wrote:Drivers are generally part of two categories: nl80211, wext. That's what you use with the --driver switch of create_ap. broadcom-wl is a wext driver. However, it does *not* support AP mode. Not even brcmsmac does. Of the broadcom drivers, only b43 does. So unless your specific chipset is supported by b43, you're out of luck. You'll have to use ad-hoc mode.
    Oh, Good answer!  I'll remember that one.

  • Windows 7 cannot find wifi

    I have recently partitioned my harddrive with boot camp and put Windows 7 on it.  I also downloaded the drivers off of the OS X Snow Leopard Install disc (but not easily, I had to work around it after getting "boot camp x64 is unsupported on this computer model" message several times).  However, I still have not been able to find any wifi (even though I know there are about 10 signals in my immediate area), so I have to connect via ethernet.  Does it have something to do with my network adapters?  Here are the ones listed under my device manager:
    Bluetooth Device (Personal Area Network) and (RFCOMM Protocol TDI)
    Broadcom NetXtreme Gigabit Ethernet
    It is very important I am able to connect to wifi!  Please help!

    Thanks for taking the time to explain Holly; it helps a lot :) 
    I've found that sound under boot camp is precarious at best. Many like you (and me at one time) thought that they had Windows installed correctly on their Macs (it still sounds awe-inspiring, even today) only to turn up the volume and....nothing. It seems to be the ever-present problem of Microsoft "wisely" picking its own drivers, even though you have just installed better ones! Video and audio drivers are usually the two nasty areas where people in-the-know (haha) go straight to the hardware manufacturer's website to download and install the most-current drivers available. 
    For your audio drivers, you need to find out the *real* manufacturers of the audio hardware to find out which drivers to install. My MBP and iMac both use Realtek drivers, who luckily keep them frequently updated. If you can't find out the make of your audio hardware, I'd just download and install the current Win7x64 drivers from http://realtek.com and try them out. If Windows shows them not-compatible with your hardware, it won't use them and you'll be back to square one. 
    Now, the wifi drivers are more tricky, since they should've been correctly installed. For them, I would go into Device Manager, find the wifi device, and click uninstall. Then reboot. Windows should install the correct drivers (if it has them or can find them). If not, we can use your OS X disk and point Windows specifically to it for the wifi hardware. But hopefully Windows will rectify everything and you'll be good to go.  
    Good luck.

  • MBP cannot find WiFi ???

    Hi when I boot my MBP it finds and connects to my WiFi. If I disactivate Airport and reactivate it, or if the MBP wakes up from standby there is no connection till I reboot MBP. This issue started with the update to Mac OS X 10.6.5 (10H574). Before it worked perfectly for 1.5 year.

    Please try the following:
    1. Delete Preferred Network(s)
    o System Preferences > Network > AirPort > Advanced > AirPort tab
    o Under "Preferred Networks," delete the network(s) you regularly use from the list.
    2. Delete AirPort Keychain Entries
    o Launch the "Keychain Access" application located in Applications/Utilties.
    o Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
    o Restart, or log out then back in.
    3. Add Preferred Network(s)
    o System Preferences > Network > AirPort > Advanced > AirPort tab
    o Add the preferred network(s) using the "+" button.
    o Restart or log out then back in.

  • Xbox360 cannot find my router, which is a WRT54GS v.6

    Can someone help me set up my router so it will be able to find it.
    I tried using some tactics found here
    http://forums.linksysbycisco.com/linksys/board/message?comm_cc=US&comm_lang=en&board.id=Wireless_Routers&message.id=53331&query.id=77031#M53331
    but it was no luck
    Thanks
    Devin 
    Solved!
    Go to Solution.

    upgrade the firmware on the router and then reset your modem and router after upgrading (use the little buttons on the back of the modem and router)
    and use the port forwarding for ports 88 and 3074 (not port triggering)

Maybe you are looking for

  • MSI KT3 Ultra-Aru (KT333) and Duron Applebred??

    Hi, welcome,willkommen,witajcie,dobry den, ... (I know this word in 11 languages) I have MSI KT3 Ultra-Aru (KT333) and J want to buy AMD Duron 1800MHz(Applebred). Does my motherboard support that processor?? It will work without problems??

  • Join me in brainstorming

    Brainstorming here has always been very helpful for me, so here I go again :) I have my tank game... whenever I get to a good break point I post what I have here: http://www.geocities.com/Malohkan/RoboTank.html So I have the enemy's AI pretty basic n

  • Is there a comparitive study of PS CS4 on Vista vs. XP?

    Hello, I have recently gotten a new computer which includes installation discs for both Windows XP and Vista Ultimate. The equipment is as follows: Dell XPS i630 computer Intel Core Duo CPU [email protected] 3.00 GB of RAM ATI Radeon HD 4800 Series D

  • Satellite L850: HDD Firmware issue preventing data recovery

    Am a bit confused and need a simple explaination My L850 hard drive died under warranty and has been sent to data recovery people to attempt to recover data before I get new drive under warranty. I am being told that my hard drive has a fairly unique

  • Can you pls tell me how to unfreeze my iMac?

    Can you pls tell me how to unfreeze my iMac?