Cannot get continuous shooting to work on new G 16. followed Manual

Solved!
Go to Solution.

Continuos is only allowed in certain shooting modes desiganted by the "O" on page 196 of your manual. What mode are you shooting in, it is not available in Auto etc.

Similar Messages

  • Cannot Get My Powerbook To Work With New Hard Drive

    My powerbook (1.67 ghz, 2 gb ram, 80 GB original hdd) was running out of room on the hard drive, so I purchased a WD 250 GB hard drive IDE to replace it. I haven't really done much on my powerbook prior to this, so I wasn't sure exactly if any problems had occured before I did this. But I replaced the drive and tried to boot from a CD and could not do it. I was using a Tiger Retail disc because I can't find my restore discs. I never had any problem reading my discs prior to this, as I have a DVD/RW drive and it has never failed on me. I tried booting from other discs as well and the same problem occured. So after several failed attempts, I connected my powerbook to my ibook through target mode and was able to install the OS on the partition of my powerbook. After completing the install, I was able to access the powerbook partition through the ibook and everything seemed fine. I unplugged the firewire cable and tried to boot my powerbook. The first time I did it, it took me past the white and grey apple screen and stuck on the blue screen, everytime after that, it hung up on the grey and white screen. I tried resetting everything through open firmware and zapping the PRAM, but no change. I tried booting into safe mode and it hung up at the grey and white screen. I was able to boot into single user mode and ran the check utility and everything came up ok. I reconnected the powerbook to the ibook and ran disk utility that way and repaired all permissions. It still has hung up on me. I've been trying to get this to work for almost 8 hours and nothing has worked for me. I'm starting to think its something really serious like a hardware failure. I don't know what version of tiger my powerbook shipped with and I'm not sure if having just 10.4 would cause this issue. I tried removing the added ram and everything as well. I hope someone can give me some things to try and hopefully get it to work. I'm pulling my hair out on this one. Any help would be greatly appreciated.

    One way to know if it is a hardware issue (or something you may have done in the DIY upgrade process, sorry) is to try putting back in the old stock 80GB drive and see if everything works well.
    If YES, then your PowerBook is fine and it is your new drive that is faulty. Return it or get a replacement under warranty (if relatively new, maybe you don't need to use the warranty).
    If NO, then something has happened during the upgrade process.
    That's my first diagnosis.

  • I cannot get GPS Only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off).  Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX

    It seems like I cannot get GPS only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off).  Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX, garmin blueChart mobile, and a GPS monitoring tool. All show no signal. If I turn on cell and wifi,  it says I get gps signal, but can't tell if that is from the GPS chip, or just from cell and wifi only (maybe with some gps mixed in)?  Any ideas on how to get iPad working with GPS only??

    Roger that.  Thanks for your time.
    System:
    Windows 7 64bit
    Processor: AMD phenom IIX4 965
    RAM:  Gskill Ripsaw F3-12800CL7D-4GBRM (2-2GB sticks)
    GPU:EVGA Classified Nvidia GeForce GTX 560 Ti 448 core
    PSU: Kingwin 1000W laser gold (LZG-1000)
    Yes. tried the one ram stick, no go.  I have been trying to boot off/install the windows 7 disk but am unable to get to the point where windows starts installing after its gathering information portion of the install.  I can get to the disk selection screen of the install with the WD HD on SATA port 2 but then get the "cant install messages" when I try to select the Vertex 3.  Yes I can see the Vertex 3 Drive as well as the WD drive at this point.  some times I have to hit "scan" a couple of times.

  • My iPhone has been badly damaged and I cannot get the screen to work. I want to do a backup to transfer to my new phone but the backup will not work because the phone is locked. Can I input my lock code to the phone via the computer to allow a backup?

    My iPhone has been badly damaged and I cannot get the screen to work. I want to do a backup to transfer to my new phone but the backup will not work because the phone is locked. Can I input my lock code to the phone via the computer to allow a backup?

    Sorry, no.

  • I cannot get airport extreme to work. Can you help me?

    I have a G5 Power PC. I recently purchased a macbook and an Airport Extreme. I cannot get the airport to work. Can somebody help me please??
    G5 Power PC and macbook   Mac OS X (10.3.9)   new OS X on Macbook

    I plug the ethernet from the airport to the back of the modem (a Webstar unit) from my cable provider. Then I plug the other cable from the back of the airport into my G5. Then plug in the power cord. I get lots of flashing lights - "thinkin & blinkin", but then I get a message that it cannot locate the server. Even rebooted. I've been waiting for the IT guy to call/email me back me back but no response yet. I'm guessing I may just need a new location, but I'm not wired to think IT-like (I'm a very right brained graphic designer), I I don't want to screw anything up.
    Do I need to just go through a new internet setup?
    G5 Power PC and macbook   Mac OS X (10.3.9)   new OS X on Macbook

  • Cannot get iTunes DJ to work

    No doubt it is something really obvious that I'm missing, but I cannot get iTunes Dj to work. If I click on iTunes DJ in the left column, right section of the window says "iTunes DJ" and explains that I can make a continuous mix, but there is no list of music. The play button is greyed out.
    The help file says "To select a specific playlist (instead of your library) for the live mix, choose an option from the Source pop-up menu at the bottom of the iTunes window."
    but there is no Source pop-up menu at the bottom of the iTunes window.
    Any ideas?

    Do you see the grey bar at the bottom of the screen when you select iTunes DJ, the one with the Settings and Refresh button, as seen in the picture on this web page? If not, then the bottom of the window may just be off the screen on your system so you don't see the Source selector. If that does seem to be the problem, try changing the resolution of your Mac's screen (Displays system preference) to the highest resolution. If it already is, try changing it to a lower resolution, then back. That may get the iTunes window to reappear..
    If not, open the Script Editor application, paste in the following text (up to and including the line that says "end tell") and click the "Run" button:
    tell application "Finder"
    set {d1, d2, d3, d4} to (get bounds of window of desktop)
    end tell
    tell application "iTunes"
    set margins to {d1 + 10, d2 + 54, d3 - 10, d4 - 148}
    set bounds of window 1 to margins
    end tell
    If the iTunes window is running off the screen, that should restore it.
    Hope this helps.

  • Cannot get screen sharing to work long distance...

    I set up an AIM account for my mother-in-law so that I could remote screen-share her MacBook and help her with learning how to use it and trouble shoot it (it's a Late 2008 Aluminum MacBook hand-me-down from my wife).
    I've set up the account, but cannot get remote screen sharing working. Screen sharing works fine over bonjour, but no go over the internet using AIM. I can control my wife's MBA from my iMac and vice-versa, but neither of us can control her MacBook. When we choose "Ask to share users screen...", we get the pop up window stating "Waiting for response from user", along with the spinning gear icon. If she chooses "Share my screen with...", the pop up window appears on our Macs and we're able to choose accept. But then the pop up window switches to "User would like you to share his or her screen" and just sits there. Nothing happens. On her screen, she gets the message "waiting for response from user" and nothing else happens.
    After a long wait, my screen will say, "There was a communication error during your chat. Messages didn't receive a response from..." and gives me the option to report the details to Apple.
    What am I doing wrong?
    Her MacBook is running Mavericks, as are our machines.
    Message was edited by: pmpknetr21
    Message was edited by: pmpknetr21

    Hi,
    @mac.com and @me.com ID works as AIM Screen Names  (you add them like they are and existing name) but only if you are using Messages 7 or 8 plus later versions of iChat 6 in Lion.
    You should be able to use the Apple Issued IDs in Mavericks.
    If you using an AIM Registered name try using it without the @AIM.com or @AOL.com suffix (User Name only)
    As AIM can "read" the Apple Database it will think the Apple IDs exist already but may not tell you that is the reason you can't re-register them.
    Can you post the info being sent to Apple here ?
    However stop the log after about 10 lines of the Binary Images (I will not need it all).
    9:28 pm      Sunday; August 3, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • HT4557 Cannot get home sharing to work... When it has before

    I have new iPad latest os, windows vista w latest itunes update.. Cannot get home sharing to work.. Signing in and out, rebooting, reinstalling, has done nothing airplay works but no home sharing...???
    I had similar issues a few years back.. Signing in and out helped.. But not this time..

    Hello there, Mr Boggles.
    The following Knowledge Base article offers up some great steps for troubleshooting issues with Home Sharing:
    Troubleshooting Home Sharing
    http://support.apple.com/kb/TS2972
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • HT2801 i cannot get my macbook to see my new usb superdrive?

    I cannot get my macbook to see my new apple
    usb superdrive

    The newest version Apple USB SuperDrive is restricted in usefulness
    to those computer models that did not ship with internal optical drives.
    Is your situation similar to one cited here(?)
    •USB SuperDrive not working as a secondary optical drive...
    https://discussions.apple.com/message/20797883#20797883
    While it has been said the firmware is such to disallow use of these
    Apple USB superdrives w/ Mac computers an internal optical drive.
    The iFixit.com site had a suggestion about that, so it may not be
    totally true. However any changes to the USB SuperDrive may void
    a warranty if you mess it up, or tamper with its design...
    •Apple USB SuperDrive  Repair - iFixit.com:
    http://www.ifixit.com/Device/Apple_USB_SuperDrive
    ...note second answer in first question, affirmative
    and the situation is conditional. It may not work
    this idea uses Terminal to change how its seen...
    A better answer is to get another brand that works as a superdrive
    for Macs and can also read/write media, boot system discs, and
    more than a few are good too, if you travel and need to change
    the region code to watch DVDs. Less costly, more disposable.
    Third party models work as external optical drive when OEM failed.
    LG, LaCie, & other USB external superdrives had been said to work.
    PS: you could also consider the iFixit page on repairing the original
    internal optical drive of your MacBook, or OWC may have video as
    well as replacement parts, and so on.
    So there are a few possible answers.
    Perhaps more than one may work.
    Good luck & happy computing!
    edited

  • I cannot get Copy & Paste to work in iOS 5

    I cannot get Copy & Paste to work on my iPhone or my iPad since updating to iOS 5.1
    I can copy and paste within an app, buy copying from one app, then going into another, Paste is not available.
    Anyone one else having this isuue? I have tried rebooting both devices but no change.

    I just checked this out by opening a doc in PlainText and copying some sameple text that I typed.  I hit enter a couple of times, pressed on the screen, the paste button appeared and I was able to paste no problem.
    I then opened a fresh document in Pages and pressed on the screen to open the paset button and got the text to paste into the Pages doc with no problem.
    You may have a glitch in your iOS 5.1 update.  You might try doing a reset all settings reset and set the phone as a new one (You should not lose any data, or media)  You will need to go in and reset any changes you may have made in settings as this set all of them back to factory defaults but your music, pictures, data, email accounts etc. will not be erased.
    If this doesn't work you may need to reinstall the iOS again.I think you can do this through iTunes but am not 100% sure.  You may need to take it to your local genius bar (Hope you have one close to your house) and ask them to reinstall the OS for you.

  • I cannot get folio builder to work in CS6 InDesign.

    I cannot get folio builder to work in InDesign. I have updated InDesign and uploaded a new all language CS6 plugin for InDesign apps but still the program says I don't have the necessary files and redirects me to the plugins I already downloaded. I am not certain what is wrong.

    DPS questions should be asked in the DPS forum. I've moved your question there.

  • Does anyone know if iCloud is offline? I cannot get my mail to work this AM

    Does anyone know if iCloud is offline? I cannot get my mail to work this AM

    Have latest version of iTunes installed and running. Also make sure you have internet access working and can access Apple websites. Also, make sure you don't have any entries in your hosts file referring to gs.apple.com....If your not sure about how to do that, go ahead and do the rest first. You can come back to that later.....Plug in phone. Put phone in DFU mode.(google put iphone in DFU mode for instructions) Then restore the phone in iTunes by highliting your device in the left column and click on the Restore button. The latest iOS version is 4.3.3. That's what iTunes will restore it to. When it's done restoring, iTunes will ask if you want to restore from a backup or setup as a new phone. I would use the Setup as a New Phone option. Once it's done, you should have a clean install of the iOS and an operating phone, as long as there are no hardware issues with it.

  • Since I downloaded Firefox 5 I cannot get the links to work for accepting or receiving gifts for Farmville & Frontiersville, what can I do

    Since I downloaded Firefox 5 I cannot get the links to work for accepting or receiving gifts for Farmville & Frontiersville, what can I do. When a request is posted on my FB page and I click on it to send or receive a gift it just shows that its "connecting" and sits there for several minutes then only sometimes actually goes to the gift. How can I fix it. My other computer that is still on firefox 4 does not have this problem.

    Hello AKBOB, if exist a problem with update or permissions then the better way is to '''download and install the new version'''.
    1. Download a copy of the latest firefox from http://www.mozilla.org/en-US/firefox/all.html
    2. '''Trash''' the current Firefox application to do a clean install.
    3. Install the version that you have downloaded.
    Do not select to remove your personal data, your profile data is stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder], so you won't lose your bookmarks or other personal data.
    see also: [https://support.mozilla.org/en-US/kb/install-firefox-mac#os=mac&browser=fx22 Installing Firefox on Mac]
    thank you

  • I have installed Mountain Lion 10.8.2 but still cannot get email from my work exchange account. I'd appreciate any help.  Thank you.

    I have installed Mountain Lion 10.8.2 but still cannot get email from my work exchange account. I'd appreciate any help.  Thank you.

    You can go to the Apple online store and purcahse a copy of Mountain Lion.  This will give you a redemption code, which you can use to download Mountain Lion from the App Store.  Unfortuantely, I'm not aware of any other way to legally purchase it.  I have never seen Apple release Muontain Lion on DVD.
    In terms of Apple Service, they just need the serial number of the machine to check the purcahse date.  It is usually correct, to within a few weeks.  A quick Google search should give you the correct number to dial.
    I hope this helps.

  • I have installed Mountain Lion 10.8.1 but still cannot get email from my work exchange account. I'd appreciate any help.  Thank you.

    I have installed Mountain Lion 10.8.1 but still cannot get email from my work exchange account. I'd appreciate any help.  Thank you.

    I would delete the account and try to re-enter it. Also, you have to let your firm's IT department know that you want to sync work email on your personal devices before they actually work.

Maybe you are looking for