Cannot get HOSTNAME to display on front panel on my new WC5955's like I can on my old WC5755's
Hi, I have set the Display Device Information option under General Setup (used to be under Security) to "HOSTNAME". I get an error stating that the HostName is not fully qualified. For security reasons, we use static IP addresses and do not want our copiers registered in DNS. We use the queue name for our host name and device name. We require that print queue name to be displayed on the copier's front panel so the users can easily identify the print queue name of the copier. The last 3-digits of the queue name is the 4th number in each printer/copier's IP address. The old WC57xx Series copiers happily display their hostnames without restriction. Why was this changed? Annoying!!! -John
After years of battling over the security issues resident with Netbios over TCP/IP Xerox has it seems removed "Windows Networking" from all current devices. This is the same thing that disables the use of scanning to a hostname instead of an IP in a non-Domain environment. Your only option here is to lie and put it manually via choosing "Contact Name" and filling in the hostname:
Similar Messages
-
How do I get the Label for a Front Panel Control to appear in the Block Diagram but not on the Front Panel? On the Front Panel I am making a complex control that consists of a Slider and a Numerical Input box. Both Controls display the same information and either can be used for Input. When one changs, the other is made to display the same value.
But I only want the Slider to display the Label on the Front Panel, to avoid confusion. On the Block Diagram however, I want both controls to display their Labels so that I know what they are. How do I display the Label for a Control on the Block diagram, but not display its Label on the Front Panel?No. The Label Visible property is separate for the front panel control label and the block diagram terminal label.
How did you start out with the block diagram's label not being visible? Whenever I drop a control or indicator, the label is always visible on both the FP and BD by default. Maybe there is a LabVIEW option that causes new controls/indicators not to have their labels visible by default, but I have yet to find it. I don't think an item should ever be dropped without the label visible, good LabVIEW coding practice demands that the labels for control terminals on the block diagram be visible so that you know what control or indicator a wire is going to.
That being said, I have seen a lot of VI's posted where the label for the terminal on the BD is not shown (against good programming practice.) I've gone to the BD and right clicked to show the label. Sometimes, the people have an empty label (which will turn off the visibility for both the FP and BD) and I'm forced to add some text of my own into the label so I can figure out what their code is doing. When I add some text to the label, at that time, I find both the BD and FP labels become visible.
Are you dealing with controls that have empty labels to start?
Good programming practices:
1. Always have a name for all of your controls, never use and empty label by deleting the text in the label.
2. Make the labels unique. For example, don't have two controls both called Stop. How do you know quickly know which terminal relates to which control?
3. Always show the labels on the block diagram, so you know the function of a control's terminal. If you want to hide the label on the FP, that's okay.
4. If you want a different label to appear on the FP than whatever you actually called the control, then use the caption. You can hide the label and show the caption. This is useful if you need to programmatically change what the "label" is on the front panel such if you are making an application that needs to change its user interface such as for a foreign language. -
How to display remote front panels of subvis that are already open
I inherited an RT project that uses remote front panels for nearly all the user interfaces. The host application opens a remote front panel the the top level RT vi, and there are several subvis on the RT system that are opened from that top level vi and thus displayed on the host (i.e. their "Show Front Panel When Called" properties are set TRUE).
If the Host loses its connection to the RT system when any subvi front panels are opened, and the host application is restarted, it can re-open the top level vi remote front panel, but all the RT subvis that are already open will not display their front panels. I am looking for a way to open the front panels to these subvis from the host application.
The kicker is, I need to know which subvis are actually running before I attempt to open remote front panels. Is there any way to determine what subvis are actively running (and not just in memory, such as subvis that won't get executed until the top level vi reaches a certain state)? I am thinking that I could create a list of the subvis that I need access to, check to see if any are actively running on the RT system, and then invoke a remote front panel connection with those that are running.
Does anyone have any ideas as to how I might be able to do so? Or any other suggestions? [and yes, I know that RFP communication is probably not the best way to go, but we're too entrenched in this software to start over with a new system!]TurboPhil wrote:
If the Host loses its connection to the RT system when any subvi front panels are opened, and the host application is restarted, it can re-open the top level vi remote front panel, but all the RT subvis that are already open will not display their front panels. I am looking for a way to open the front panels to these subvis from the host application.
It might be possible to work around this behavior by placing VI invoke nodes in your top level VI that reference each of your subvis and setting the Wait Until Done invoke method to false. This should cause the subvi to close when the top level VI closes even in the case of an unexpected restart.
You can access this invode node in the functions pallet by selecting Application Control » Invoke Node and also selecting Application Control » Static VI reference. Wire the Static VI Reference to the vi reference input node and double click the Static VI Reference and select the appropriate subvi in the dialog window. Left click on the Method section of the invoke node and select Run VI. Finally right click on the Wait Until Done invoke method and select Create Constant and ensure this constant is set to false.
TurboPhil wrote:
The kicker is, I need to know which subvis are actually running before I attempt to open remote front panels. Is there any way to determine what subvis are actively running (and not just in memory, such as subvis that won't get executed until the top level vi reaches a certain state)? I am thinking that I could create a list of the subvis that I need access to, check to see if any are actively running on the RT system, and then invoke a remote front panel connection with those that are running.
You can access this information by using the Real-Time System Manager (Tools » Real-Time Module » System Manager). This can be used to show what VIs and subvis are loaded into memory and which are running.
For more information on using this tool please referere to this Knowledge Base article.
Message Edited by BLAQmx on 02-18-2008 11:40 AM
Mark
LabVIEW R&D -
I already have an itunes account on my laptop but have been setup on a mac and have songs that have not been purchased from the itunes store, I cannot get the songs from my iPhone onto my itunes account on the mac. how can I do this?
You copy them from your old computer or your backup copy of your old computer.
The iphone is not a backup/storage device. -
I downloaded Icloud somehow I changed my itunes account information and cannot get back to my original account that had a redeemed balance on it how can I get back to the original account?
Buy the songs that your friend put on the iPod that you liked. They had no right to give you the copyrighted music when they sold you the device.
tt2 -
I cannot get my 1st generation iPod Nano to sync my new downloads from itunes on my macbook air. Is this possible or not?
Are you noticed that there are replacement program for iPod Nano 1st gen?
I've had replace my iPod nano 1st with 8 Gb iPod Nano 6th gen last year.
Check this out --> http://www.apple.com/support/ipodnano_replacement/ -
i have a broken desktop which had my itunes account on it.
I am trying to get the information onto a new laptop and itunes programme but cannot. I have only managed to copy over some of my music as i had it on an external drive.
I also cannot get my iphone 5 to be recognized on the new itunes.
HELPiTunes as you see it in the application window uses a series of files and folders contained in the iTunes folder. Some people make the mistake of only backing up their media in which case all you have is a bunch of media files without the iTunes structure. In that case you have to build a new library yourself.
What exactly do you mean "not recognized"? The phone does not show up on the computer at all, or it does but it says it will wipe the phone? The wipe the phone stuff is again because it cannot find the original library to which it was synced. You need to transfer the entire iTunes folder from the old computer or the backup you made of it.
What are the iTunes library files? - http://support.apple.com/kb/HT1660
More on iTunes library files and what they do - http://en.wikipedia.org/wiki/ITunes#Media_management
What are all those iTunes files? - http://www.macworld.com/article/139974/2009/04/itunes_files.html
Where are my iTunes files located? - http://support.apple.com/kb/ht1391 -
I am working through the eBook "Building Cloud Apps with Microsoft Azure" and when I run New-AzureWebsiteEnv.ps1 I get the following error
Error: Cannot get Azure subscription ID and thumbprint. Failed in New-FirewallRuleForWebsite in New-AzureSql.ps1
I have already tried adding -ExtendedDetails to Get-AzureSubscription in New-AzureSql.ps1 and New-AzureWebsiteEnv.ps1.
I am using Azure PowerShell 0.8.16 and Windows 7 Service Pack 1.Hi,
Not too sure if you have tried this:
In the code you will have a line:
$s = Get-AzureSubscription –Current
Change that line to:
$s = Get-AzureSubscription -Current –ExtendedDetails
The difference between the two lines is that the –ExtendedDetails will return the Thumbprint required by the code
Reference:=
http://blogs.msdn.com/b/devschool/archive/2015/04/10/error-in-fixit-demo-cannot-get-azure-subscription-id-and-thumbprint-urghh.aspx
Regards,
Mekh. -
How do I reestablish hotmail delivery to my iPhone and iPad after I have been locked out? I have reestablished service to my PC, but cannot get email on other devices, even after updating to new passwords.
Sometimes it is fruitless to try to "fix" a broken account on an iOS device. I would delete the account on both devices and then configure the account again from scratch.
-
Since I downloaded Firefox 5 I cannot get the links to work for accepting or receiving gifts for Farmville & Frontiersville, what can I do. When a request is posted on my FB page and I click on it to send or receive a gift it just shows that its "connecting" and sits there for several minutes then only sometimes actually goes to the gift. How can I fix it. My other computer that is still on firefox 4 does not have this problem.
Hello AKBOB, if exist a problem with update or permissions then the better way is to '''download and install the new version'''.
1. Download a copy of the latest firefox from http://www.mozilla.org/en-US/firefox/all.html
2. '''Trash''' the current Firefox application to do a clean install.
3. Install the version that you have downloaded.
Do not select to remove your personal data, your profile data is stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder], so you won't lose your bookmarks or other personal data.
see also: [https://support.mozilla.org/en-US/kb/install-firefox-mac#os=mac&browser=fx22 Installing Firefox on Mac]
thank you -
Need to know how to get my apple account to sync up with a new email on my phone and delete the old one in a step by step process??
After you change the account settings as I described below hold your finger on any app until they all wriggle, then tap the "-" on each purchased with her Apple ID. Press the HOME button when done. Then go to the App Store and buy or download the apps you want.
-
I can't get Photoshop Elements 5.0 to work on my new PC running Windows 7 - can anyone help?
I can't get Photoshop Elements 5.0 to work on my new PC running Windows 7 - can anyone help?
It won't work. It's simply not compatible. Buy Elements 11.
Mylenium -
How to get Labview RT to Display a Front Panel on the Graphics port
I suspect that this post belongs on the feature request board but I'll ask anyway.
Most of my systems require a seperate PC for a SCADA/HMI/User interface linked to the RT controller using Network Published Shared Variables.
I understand that Remote Panels and Web Interfaces are also an option, bu still requires a PC to Access them.
I use high end RT controllers such as PXI, CRIO, and of 3 hours ago Desktop PC's.
Each has a DVI or VGA port connected to a graphics processor.
What I would like to be able to do is display my main VI front Panel to a connected monitor.
A possible solution is to use a windows OS but it is no good for a precision realtime system.
Any thoughts?
iTm - Senior Systems Engineer
uses: LABVIEW 2012 SP1 x86 on Windows 7 x64. cFP, cRIO, PXI-RTDan,
As above, Web interface still requires additional hardware of some sort.
Apple is a closed system so loads of prlems with 1/2 the market,
I am warming up to the hypervisor, I just don't like the idea of it taking out an entire core (on a dual core system). And needing a windows licence to go with it as well.
A quad Core PXI puts a gaping hole in my budget, makes a second PC not seem so expensive.
Would be great if I could get it on a Desktop, quad cores are pretty cheap now.
iTm - Senior Systems Engineer
uses: LABVIEW 2012 SP1 x86 on Windows 7 x64. cFP, cRIO, PXI-RT -
I can successfully view and control a VI remotly. However, the remote VI dinamically loads another VI, this VI loaded dinamically is a VI that allows open others VIs, I want to see the files that contains the server machine, in the client machine, but the front panel of the dinamic VI appears only on the server and not on the client, How can I display the fron panel with the files of the server machine of the dinamically loaded VI on the client computer?
Attachments:
micliente.llb 183 KB
miservidor.llb 186 KB
rdsubvis.llb 214 KBI down loaded your files but could use some instructions on what needs run.
It seems that you are so close yet so far. You need to get the data on the server machine over to the client. I generally do this by doing a call by reference (on the client machine) of a VI that is served by the server. THe VI that executes on the server should pass the data you want to diplay via one of its output terminals. You can simply wire from this terminal (back on the client again) to an indicator of your choosing.
Now theorectically, I do not think that there is anything that prevents use from getting the control refnum of the actual indicator (on the server) of the indicator that has the data, and read its "Value" using a property node. I have never tried this idea but it seems t
hat all of the parts are there. You will need to know the name of the VI that holds the data as well as the indicator's name. You will also have to serve all VI's. This is not a good idea.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction -
Cannot get iphoto to display imported pictures
Recently I used Duplicate Annihilator to remove duplicates from iphoto '09, which were imported from many folders of pictures (not directly from a camera) and I just noticed that all photos which had duplicates are now no longer in my photo library at all. This was around 2,000 photos. I used finder to search for a specific folder that I imported and that is no longer visible in iphoto and I am able to locate the folder and files of all missing pictures inside the iphoto library file.
So how do I get iphoto to display these files which are in the iphoto library but cannot be found in iphoto?
I have tried rebuilding the photo library by using command-alt-shift and opening iphoto, but it did not work. It did, however, create more duplicates which I am scared to annihilate out of fear that I will lose those completely as well.Welcome to the Apple Discussions. Run the two fixes below in order as needed:
Fix #1
Rebuild the library using iPhoto Library Manager as follows:
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 -Download iPhoto Library Manager and launch.
2 -Click on the Add Library button, navigate to your User/Pictures folder and select your iPhoto Library folder.
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File->Rebuild Library menu option
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: It may take some time to create the new library if you have a lot of photos.
Fix #2
Start over with a new library and import the Originals folder from your original library as follows:
Creating a new library while preserving the Events from the original library.
1. Move the existing library folder to the desktop.
2. Open the library package like this.
3. Launch iPhoto and, when asked, select the option to create a new library.
4. Drag the Originals folder from the iPhoto Library on the desktop into the open iPhoto window.
This will create a new library with the same Events as the original library if you have the Finder checkbox unchecked in the Events preference pane.
Maybe you are looking for
-
Order of stop and start of reporting services
Hi All, I am using 11.1.1.3 version in my laptop,i want know the correct order of stop and start the services,please help me on this. Thanks Hypuser
-
Satellite A300-1JH PSAGLE: Control buttons don't work with XP
Hello there. I own a Toshiba Satellite A300 psagle. It works beautifully, but there is a problem: the tactile music buttons don't work. I am using Windows XP and I have installed all the drivers available. Could some one please tell me what I should
-
CreateComponentsFromDescriptors doesn't work in Flex4
Hi all, I set the application itself to have creationPolicy="none" and then try to call createComponentesFromDescriptors at the end of my event handler that parses the configuration file. But for whatever reason, it still doesn't instantiat
-
Can we add more plan type to EPMA or Classic planning App once deployed.
Hello Gurus, I have EPMA planning application ABC with two plan types enabled i.e Plan1 and Plan2. Application is already in deployed stat. so now is it possible to enable more plan types for same application. All help is highly appreciated. Thanks Y
-
Disable Edit Content button on virtual content management reposititory
Hello, i have a requirement to disable content edit in virtual content management repository (Weblogic portal administration console). i set delegated administration to view capability on Repository and it took out all delete and add functionality bu