Cannot get n to enable.

Ok, so I have a brand new macbook pro w 2.16 intel core duo, and a new 802.11n airport extreme base station. i have installed the new 2007001 airport update and supposedly have installed the n enabler from the disk that came with the base station. When i check my network utility in th en1 screen it just says a/b/g enabled. How on earth do I get the n enabled? I called apple support, and they said, hmmmmmmm. . . . good question. Instead of screaming I just hung up and decided to ask the experts here.

Magpie's correct. The CD portables didn't ship with 802.11n ready Airport cards.
You can verify this by following the following procedure:
Open Network Utility (found in the Applications > Utilities folder)
Under the Info Tab, choose Network Interface (en1)
In the section "Model: Wireless Network Adapter," if it says (802.11a/b/g/n), you already have the 802.11n enabler installed. If it says (802.11a/b/g), you do not have the 802.11n enabler installed.
You can, however, obtain an 802.11n Airport card from a Core 2 Duo MacBook Pro (not MacBook) and swap out the Airport card in your Core Duo MacBook.
Mine arrived today and I should have it installed sometime tomorrow.

Similar Messages

I cannot get GPS Only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off). Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX

It seems like I cannot get GPS only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off). Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX, garmin blueChart mobile, and a GPS monitoring tool. All show no signal. If I turn on cell and wifi, it says I get gps signal, but can't tell if that is from the GPS chip, or just from cell and wifi only (maybe with some gps mixed in)? Any ideas on how to get iPad working with GPS only??

Roger that. Thanks for your time.
System:
Windows 7 64bit
Processor: AMD phenom IIX4 965
RAM: Gskill Ripsaw F3-12800CL7D-4GBRM (2-2GB sticks)
GPU:EVGA Classified Nvidia GeForce GTX 560 Ti 448 core
PSU: Kingwin 1000W laser gold (LZG-1000)
Yes. tried the one ram stick, no go. I have been trying to boot off/install the windows 7 disk but am unable to get to the point where windows starts installing after its gathering information portion of the install. I can get to the disk selection screen of the install with the WD HD on SATA port 2 but then get the "cant install messages" when I try to select the Vertex 3. Yes I can see the Vertex 3 Drive as well as the WD drive at this point. some times I have to hit "scan" a couple of times.

I cannot get my iMac with built-in airport to allow internet connections to Nook and PS3. The devices access the network, but internet connection fails. Internet sharing is enabled, network security (WEP, WPA) is completely off. What to check next?

I cannot get my iMac with built-in airport wi-fi to allow internet connections to Nook and PS3. The devices access the network, but internet connection fails. Internet sharing is enabled, network security (WEP, WPA) is disabled. What to check next?

On an additional note, I've purchased a wireless router and everything connected on the first attempt. It just vexes me that the built-in wireless isn't working as a router. Is this another example of "Mac only plays with Mac"?

I cannot get iDVD, what is the best alternative app to enable me to burn my projects to DVD?

I cannot get iDVD, what is the best alternative app to enable me to burn my iMovie projects to DVD? why do Apple think that no one needs to burn DVDs?

Why is there no iDVD on my new Mac?
Apple insists that the entire world has access to fast broadband (and are prepared to pay for the considerable bandwidth usage) and wants to distribute home movies to friends and relatives via download (iCloud, YouTube, Facebook, whatever) rather than mailing them a DVD. The fact that in reality not all users do, has so far had no effect on this policy. If you scream and shout loudly enough down the phone Apple may send you a free copy of iDVD. Stating that they would return their brand new Mac unless they received a copy of iDVD worked for some, but that is now said to have been withdrawn by Apple. Also, you can complain bitterly here, perhaps suggesting that Apple could have provided a choice between burning DVDs and distributing home movies by other means:
http://www.apple.com/feedback/
Whilst Macs with a Superdrive continue to be able to burn video DVDs, the software for so doing, iDVD, is no longer included in the iLife bundle that comes with OS 10.7 Lion (which also omitted iWeb) or will come with OS 10.8 Mountain Lion. And it is no longer included in the iLife 11 from the online Apple Store: http://www.apple.com/ilife/. Your only solution is to look on Amazon or eBay and try to get an older version that includes iDVD 7, i.e. iLife version 9 onwards. You should also do this if you plan to buy a new Mac anytime soon, as stocks of iLife that include iDVD will not be available for ever.
However, the vastly more expensive FCPX can burn a DVD without iDVD or DVD Studio Pro involvement, but lack the themes etc of iDVD. Also, of course, there is Roxio Toast, which is the best software for burning anything but again does not offer the flexibility of iDVD.
And if you think Microsoft are any better, their new Windows 8 operating system will not play DVDs, or burn them, unless customers buy an extra upgrade, the company has announced: http://www.gizmag.com/windows-8-no-dvd-playback/22443/
In other words, computer manufacturers have declared optical media as dead, long before consumers are ready to stop using them, which is fine as long as they offered us a choice, but they won’t even do that. Flexibility and intuitive use of a computer seems to be a thing of the past.

I cannot get scrolling to work on DV6-6172nr. The 2 finger scroll is enabled & new drivers install

I cannot get scrolling to work on DV6-6172nr. The 2 finger scroll is enabled but doesn't work. I have downloaded the latest drivers and still no vertical scrolling. This could be a deal breaker. I have only had this laptop for 2 days and if I can't resolve this issue, the laptop is going back to the store. Please help.

Hi,
First, download the latest Synaptics driver installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp54001-54500/sp54483.exe
Next, open windows Control Panel, open Programs and Features, right click the entry 'Synaptics Pointing Device Driver' and select Uninstall.
When this has completed, restart the notebook.
When windows has fully reloaded, open your Downloads folder, right click the Synaptics installer and select 'Run as Administrator' to start the installation. When this has completed, restart the notebook again. You may have to check that Two Finger Scrolling is enabled in the device settings tab under Mouse.
If this fails to correct the problem, I think I would agree with what you suggest yourself and simply return the notebook.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

HT203609 On my 6 plus I cannot get consistent email notifications. I have wifi. Notifications are enabled for the gmail account. Anyone have an idea?

On my 6 plus I cannot get consistent email notifications. I have wifi. Notifications are enabled for the gmail account. Anyone have an idea?

Hi Try this Settings, email account Sign, out then Sign, back, in do this will all Email, Accounts that are not working. Cheers Brian

HT4914 I subscribed to itunes match, but cannot get it enabled on my iPad

I subscribed to itunes match, but cannot get it enabled on my iPad

Hi Popsman61,
If you are having issues enabling iTunes Match on your iPad, you may find the following article helpful:
iTunes: How to add a computer or iOS device to iTunes Match
http://support.apple.com/kb/ht4913
Regards,
- Brenden

Cannot get fill-in boxes to be enabled

I have a BI Publisher report which has a number of areas for the user to complete once the report has been generated. Most of the fields are enabled, but a number of the fields are disabled. Does anyone have a clue to how to get these fields enabled?
I am currently using BI Publisher 11.1.1.6 with Microsoft Windows. (I will forward the template and sample data if you want to try.)
Thanks

Don't know if this will help: http://email.about.com/od/macosxmailtips/qt/et072106.htm

Cannot get xorg to work at all

Granted I have yet to try vesa, but frankly if I cannot get the fglrx driver to work then I am not interested in this distro. Following the wiki instructions has gotten me nowhere and forum searches have turned up 4 year old posts. I have installed Xorg 1.11 from the repository listed on the catalyst page. I have installed the drivers also from the repo listed on the wiki page. I have a Dell XPS 1645 with an AMD HD 5730. fglrx module is running radeon is blacklisted and is not running. nomodeset is on my kernel line. running Xorg -configure says no devices to configure. fglrxinfo says unable to open display (null). If I delete xorg.conf startx says failed to load module ati, vesa, and fbdev, and then says fatal error no screens found. If I run aticonfig --initial it creates xorg.conf, but startx still will not work. The screen will go blank like it is about to load but there is an error fglrx: no matching Device section for instance (BusID PCI :0@2:0:1) found and xinit: connection to server lost. Running Xorg -configure still states no devices to configure. I'm really hoping this is something stupid that I have missed doing, as I do want to use this distro but my time is not infinite, and ubuntu and friends are just so easy. Not like I've never run Arch or Gentoo before either. If my tone is off I'm sorry, it's 2:30 AM here and I'm tired

I also had trouble with my ATI Radeon after the upgrade and solved the problem by a revert.
For this I used (for "extra") the repository http://arm.konnichi.com/2012/03/10/extra/os/i686/
The archlinux wiki explains for "xorg" how to do reverts using such repositories ;-)
I now run upgrades like this (example as of today):
$ sudo pacman -Syuw --ignore ati-dri,libgl,xf86-input-evdev,xf86-video-ati,xf86-video-fbdev,xf86-video-vesa,xorg-server,xorg-server-common,xorg-xinput
:: Synchronizing package databases...
core 104.9 KiB 117K/s 00:01 [###] 100%
extra 1388.4 KiB 123K/s 00:11 [###] 100%
community 1588.5 KiB 123K/s 00:13 [###] 100%
archlinuxfr is up to date
:: Starting full system upgrade...
warning: ati-dri: ignoring package upgrade (7.11.2-1 => 8.0.1-2)
warning: libgl: ignoring package upgrade (7.11.2-1 => 8.0.1-2)
warning: xf86-input-evdev: ignoring package upgrade (2.6.0-4 => 2.7.0-1)
warning: xf86-video-ati: ignoring package upgrade (6.14.3-1 => 6.14.3-2)
warning: xf86-video-fbdev: ignoring package upgrade (0.4.2-5 => 0.4.2-6)
warning: xf86-video-vesa: ignoring package upgrade (2.3.0-7 => 2.3.0-8)
warning: xorg-server: ignoring package upgrade (1.11.4-1 => 1.12.0-1)
warning: xorg-server-common: ignoring package upgrade (1.11.4-1 => 1.12.0-1)
warning: xorg-xinput: ignoring package upgrade (1.5.3-2 => 1.5.99.1-1)
For the time being I am out of trouble, but in case someone is interested in understanding the problem:
======== PCI devices ========
Host bridge ATI Technologies Inc Radeon 9100 IGP Host Bridge
PCI bridge ATI Technologies Inc Radeon 9100 IGP PCI/AGP Bridge
USB Controller ATI Technologies Inc Device 4367
USB Controller ATI Technologies Inc Device 4368
USB Controller ATI Technologies Inc Device 4365
SMBus ATI Technologies Inc SMBus
IDE interface ATI Technologies Inc Device 4369
ISA bridge ATI Technologies Inc Device 436c
PCI bridge ATI Technologies Inc Device 4362
Multimedia audio controller ATI Technologies Inc IXP SB300 AC'97 Audio Controller
VGA compatible controller ATI Technologies Inc Radeon 9100 PRO IGP
== Xprg.0.log ==
[ 260.602]
X.Org X Server 1.12.0
Release Date: 2012-03-04
[ 260.602] X Protocol Version 11, Revision 0
[ 260.602] Build Operating System: Linux 3.2.9-1-ARCH i686
[ 260.602] Current Operating System: Linux arch200905 3.2.9-1-ARCH #1 SMP PREEMPT Thu Mar 1 09:10:44 UTC 2012 i686
[ 260.602] Kernel command line: vga=0xF06 root=/dev/disk/by-uuid/[confidential ... ...] ro
[ 260.602] Build Date: 05 March 2012 06:02:28AM
[ 260.602]
[ 260.602] Current version of pixman: 0.24.4
[ 260.602] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 260.602] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 260.603] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Mar 13 09:47:44 2012
[ 260.654] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 260.674] (==) No Layout section. Using the first Screen section.
[ 260.674] (==) No screen section available. Using defaults.
[ 260.674] (**) |-->Screen "Default Screen Section" (0)
[ 260.674] (**) | |-->Monitor "<default monitor>"
[ 260.692] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 260.692] (==) Automatically adding devices
[ 260.692] (==) Automatically enabling devices
[ 260.828] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 260.828] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 260.828] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 260.828] (II) Loader magic: 0x822e580
[ 260.828] (II) Module ABI versions:
[ 260.828] X.Org ANSI C Emulation: 0.4
[ 260.828] X.Org Video Driver: 12.0
[ 260.828] X.Org XInput driver : 16.0
[ 260.828] X.Org Server Extension : 6.0
[ 260.829] (--) PCI:*(0:1:5:0) 1002:7834:1509:9269 rev 0, Mem @ 0xe8000000/67108864, 0xec020000/65536, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[ 260.830] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 260.830] (II) LoadModule: "extmod"
[ 260.882] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 260.918] (II) Module extmod: vendor="X.Org Foundation"
[ 260.918] compiled for 1.12.0, module version = 1.0.0
[ 260.918] Module class: X.Org Server Extension
[ 260.918] ABI class: X.Org Server Extension, version 6.0
[ 260.918] (II) Loading extension MIT-SCREEN-SAVER
[ 260.918] (II) Loading extension XFree86-VidModeExtension
[ 260.918] (II) Loading extension XFree86-DGA
[ 260.931] (II) Loading extension DPMS
[ 260.931] (II) Loading extension XVideo
[ 260.931] (II) Loading extension XVideo-MotionCompensation
[ 260.931] (II) Loading extension X-Resource
[ 260.931] (II) LoadModule: "dbe"
[ 260.932] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 260.933] (II) Module dbe: vendor="X.Org Foundation"
[ 260.933] compiled for 1.12.0, module version = 1.0.0
[ 260.934] Module class: X.Org Server Extension
[ 260.934] ABI class: X.Org Server Extension, version 6.0
[ 260.934] (II) Loading extension DOUBLE-BUFFER
[ 260.934] (II) LoadModule: "glx"
[ 260.934] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 260.987] (II) Module glx: vendor="X.Org Foundation"
[ 260.987] compiled for 1.12.0, module version = 1.0.0
[ 260.987] ABI class: X.Org Server Extension, version 6.0
[ 260.987] (==) AIGLX enabled
[ 260.987] (II) Loading extension GLX
[ 260.988] (II) LoadModule: "record"
[ 260.988] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 260.999] (II) Module record: vendor="X.Org Foundation"
[ 260.999] compiled for 1.12.0, module version = 1.13.0
[ 260.999] Module class: X.Org Server Extension
[ 260.999] ABI class: X.Org Server Extension, version 6.0
[ 260.999] (II) Loading extension RECORD
[ 260.999] (II) LoadModule: "dri"
[ 261.000] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 261.009] (II) Module dri: vendor="X.Org Foundation"
[ 261.009] compiled for 1.12.0, module version = 1.0.0
[ 261.009] ABI class: X.Org Server Extension, version 6.0
[ 261.009] (II) Loading extension XFree86-DRI
[ 261.010] (II) LoadModule: "dri2"
[ 261.010] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 261.016] (II) Module dri2: vendor="X.Org Foundation"
[ 261.016] compiled for 1.12.0, module version = 1.2.0
[ 261.016] ABI class: X.Org Server Extension, version 6.0
[ 261.017] (II) Loading extension DRI2
[ 261.017] (==) Matched ati as autoconfigured driver 0
[ 261.017] (==) Matched vesa as autoconfigured driver 1
[ 261.017] (==) Matched fbdev as autoconfigured driver 2
[ 261.017] (==) Assigned the driver to the xf86ConfigLayout
[ 261.017] (II) LoadModule: "ati"
[ 261.035] (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
[ 261.045] (II) Module ati: vendor="X.Org Foundation"
[ 261.045] compiled for 1.11.99.902, module version = 6.14.3
[ 261.045] Module class: X.Org Video Driver
[ 261.046] ABI class: X.Org Video Driver, version 12.0
[ 261.046] (II) LoadModule: "radeon"
[ 261.046] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[ 261.106] (II) Module radeon: vendor="X.Org Foundation"
[ 261.106] compiled for 1.11.99.902, module version = 6.14.3
[ 261.106] Module class: X.Org Video Driver
[ 261.106] ABI class: X.Org Video Driver, version 12.0
[ 261.121] (II) LoadModule: "vesa"
[ 261.121] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[ 261.139] (II) Module vesa: vendor="X.Org Foundation"
[ 261.139] compiled for 1.11.99.903, module version = 2.3.0
[ 261.139] Module class: X.Org Video Driver
[ 261.139] ABI class: X.Org Video Driver, version 12.0
[ 261.139] (II) LoadModule: "fbdev"
[ 261.139] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[ 261.140] (II) Module fbdev: vendor="X.Org Foundation"
[ 261.140] compiled for 1.11.99.903, module version = 0.4.2
[ 261.140] ABI class: X.Org Video Driver, version 12.0
[ 261.140] (II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI FireMV 2400 3155 (PCI),
ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
AMD FireStream 9250, ATI FirePro V8700 (FireGL),
ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
ATI Mobility RADEON HD 4870, ATI Radeon 4800 Series,
ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
ATI Mobility Radeon HD 4650, ATI Radeon RV730 (AGP),
ATI Mobility Radeon HD 4670, ATI FirePro M5750,
ATI Mobility Radeon HD 4670, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon RV710,
ATI Radeon HD 4350, ATI Mobility Radeon 4300 Series,
ATI Mobility Radeon 4500 Series, ATI Mobility Radeon 4500 Series,
ATI FirePro RG220, ATI Mobility Radeon 4330, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon HD 3470,
ATI Mobility Radeon HD 3430, ATI Mobility Radeon HD 3400 Series,
ATI Radeon HD 3450, ATI Radeon HD 3450, ATI Radeon HD 3430,
ATI Radeon HD 3450, ATI FirePro V3700, ATI FireMV 2450,
ATI FireMV 2260, ATI FireMV 2260, ATI Radeon HD 3600 Series,
ATI Radeon HD 3650 AGP, ATI Radeon HD 3600 PRO,
ATI Radeon HD 3600 XT, ATI Radeon HD 3600 PRO,
ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
ATI Mobility FireGL V5700, ATI Mobility FireGL V5725,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3300 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3000 Graphics, SUMO, SUMO, SUMO2, SUMO2, SUMO2, SUMO2,
SUMO, SUMO, SUMO, SUMO, SUMO, ATI Radeon HD 4200, ATI Radeon 4100,
ATI Mobility Radeon HD 4200, ATI Mobility Radeon 4100,
ATI Radeon HD 4290, ATI Radeon HD 4250, AMD Radeon HD 6310 Graphics,
AMD Radeon HD 6310 Graphics, AMD Radeon HD 6250 Graphics,
AMD Radeon HD 6250 Graphics, AMD Radeon HD 6300 Series Graphics,
AMD Radeon HD 6200 Series Graphics, CYPRESS,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, AMD Firestream 9370,
AMD Firestream 9350, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5900 Series,
ATI Radeon HD 5900 Series, ATI Mobility Radeon HD 5800 Series,
ATI Mobility Radeon HD 5800 Series,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon HD 5570,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon Graphics,
ATI Mobility Radeon Graphics, CEDAR,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI FirePro 2270, CEDAR,
ATI Radeon HD 5450, CEDAR, CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN, AMD Radeon HD 6900 Series,
AMD Radeon HD 6900 Series, CAYMAN, CAYMAN, CAYMAN,
AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series, BARTS,
BARTS, Mobility Radeon HD 6000 Series,
Mobility Radeon HD 6000 Series, BARTS, BARTS, BARTS, BARTS,
AMD Radeon HD 6800 Series, AMD Radeon HD 6800 Series,
AMD Radeon HD 6700 Series, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, CAICOS,
CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS,
CAICOS, CAICOS, CAICOS
[ 261.148] (II) VESA: driver for VESA chipsets: vesa
[ 261.148] (II) FBDEV: driver for framebuffer: fbdev
[ 261.148] (--) using VT number 7
[ 261.153] (II) [KMS] drm report modesetting isn't supported.
[ 261.154] (WW) Falling back to old probe method for vesa
[ 261.154] (WW) Falling back to old probe method for fbdev
[ 261.154] (II) Loading sub module "fbdevhw"
[ 261.154] (II) LoadModule: "fbdevhw"
[ 261.155] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[ 261.196] (II) Module fbdevhw: vendor="X.Org Foundation"
[ 261.196] compiled for 1.12.0, module version = 0.0.2
[ 261.196] ABI class: X.Org Video Driver, version 12.0
[ 261.196] (EE) open /dev/fb0: No such file or directory
======== error reported from startx ========
X.Org X Server 1.12.0
Release Date: 2012-03-04
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.2.9-1-ARCH i686
Current Operating System: Linux arch200905 3.2.9-1-ARCH #1 SMP PREEMPT Thu Mar 1 09:10:44 UTC 2012 i686
Kernel command line: vga=0xF06 root=/dev/disk/by-uuid/... ... ... ... ro
Build Date: 05 March 2012 06:02:28AM
Current version of pixman: 0.24.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Mar 13 09:47:44 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
(II) [KMS] drm report modesetting isn't supported.
/usr/bin/X: symbol lookup error: /usr/lib/xorg/modules/drivers/radeon_drv.so: undefined symbol: pciTag
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
This is a temporary solution. I hope, that I can do regular upgrades again later.
Best regards from Munich
Goetz
==== 2012-03-14 09:49 UTC ================================================
I am trying to find the culprit. Besides xorg, I also blocked ati-dri and libgl. But they work fine on my PC.
Thus, this is ok:
ati-dri: package upgrade (7.11.2-1 => 8.0.1-2)
libgl: package upgrade (7.11.2-1 => 8.0.1-2)
In /etc/pacman.conf I entered:
# Pacman won't upgrade packages listed in IgnorePkg and members of IgnoreGroup
IgnorePkg = xorg-server-common
IgnoreGroup = xorg
Last edited by goetzkluge (2012-03-14 10:23:47)

Cisco ASA 5505 Cannot ping local traffic and local hosts cannot get out

I have, what I believe to be, a simple issue - I must be missing something.
Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209).
There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off.
The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue.
Basically, the VPN is up and running but PC 10.51.253.210 cannot get out.
Any ideas? Sanitized Config is below. Thanks !
ASA Version 7.2(4)
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif Inside
security-level 100
ip address 10.51.253.209 255.255.255.248
interface Vlan2
nameif Outside
security-level 0
ip address ***** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name *****
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
pager lines 24
mtu Outside 1500
mtu Inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any Outside
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list No_NAT
route Outside 0.0.0.0 0.0.0.0 ***** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set DPS_Set esp-3des esp-md5-hmac
crypto map DPS_Map 10 match address Outside_VPN
crypto map DPS_Map 10 set peer *****
crypto map DPS_Map 10 set transform-set *****
crypto map DPS_Map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
console timeout 0
management-access Inside
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group ***** type ipsec-l2l
tunnel-group ***** ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8d0adca63eab6c6c738cc4ab432f609d
: end
1500

Hi Martin,
Which way you are trying. Sending traffic via site to site is not working or traffic which you generate to outside world is not working?
But you say ASA connected interface to PC itself is not pinging that is strange. But try setting up the specific rules for the outgoing connection and check. Instead of not having any ACL.
If it is outside world the you may need to check on the NAT rules which is not correct.
If it is site to site then you may need to check few other things.
Please do rate for the helpful posts.
By
Karthik

Open script cannot get connection from the brower helper after 15 seconds.

Error:
===
Open script cannot get connection from the brower helper after 15 seconds. Do you want to continue waiting for the browser to load?
Please Note:
========
1. I have tried this only on IE
2. I am running OATS on a Remote desktop
Situation:
======
Trying to stop the recording
Try to get xpath of an object using Inspect Path
Setup details
========
Windows XP 5.1 Service Pack 3, x86
OpenScript 12.1.0.1.383
Internet Explorer 8.0.6001.18702
FireFox 13.0.1
Mitigation steps done till now:
==================
1. Disabled windows firewall
2. Disable XSS filter setting
3. Restarted the ATS services (3 of them)
4. Run the Open Script Diagnosis Tool (PS: There are 3 errros even after running it. The 3 errros are listed in the workspace_log log file snippet below...)
Error in worspace_log:
=============
To Change setting:
Go to Tools > Internet Options and Choose Security Tab
Select the Zone to modify and Press Custom level
Find Enable XSS filter Setting - Select Disable and click Ok
!ENTRY oracle.oats.scripting.diagnosisTool.api.DiagnosisExecutor 4 0 2012-07-09 17:08:52.594
!MESSAGE Failure found when diagnosing Oracle EBS/Forms Load Testing Forms LT Diagnoser
!ENTRY oracle.oats.scripting.diagnosisTool.api.DiagnosisExecutor 4 0 2012-07-09 17:08:52.594
!MESSAGE Did not auto-fix the problem.
!ENTRY oracle.oats.scripting.diagnosisTool.api.DiagnosisExecutor 4 0 2012-07-09 17:08:52.594
!MESSAGE Suggestion for fixing: Please change your Java proxy setting to Use Browser Settings
Aprreciate help on this.

To resolve this, you need to reconfigure the "Oracle Application Testing Suite Helper Service" (OATSHelperSvr) to start as a user who has privledges to run open script tests rather than the default SYSTEM user.
Reconfiguring the OATSHelperSvr Service:
1. Open the services panel (Start > Run > services.msc)
2. Find the Oracle Application Testing Suite Helper Service
3. Right Click > Properties then select the Log On Tab
4. Specify an interactive user that has rights to run OpenScript (test by logging in as that user and running tests):
5. Click OK
6. Restart the service after dialogs are closed by Right Click > Restart
7. You should now repeat this process for the "Oracle Application Testing Suite Agent Service" (eLoadAgentMon) Service (Two services in
total)
You should now retry running the test in Oracle Test Manager

HP Smart Web Printing / IE8 / Windows Vista: Cannot get icon to appear!

I've installed HP Smart Web Printing 4.5.1 in IE8 running under Vista SP2. I cannot get the icon to appear. Under Tools/Manage Add-ons, "Show or Hide HP Smart Web Printing" is reported as "enabled". When I select "Show or hide HP Smart Web Printing" under the double arrows at the far right of the tool bar, nothing happens. I see others have had some success at getting through this, but nothing seems to be working for me. I've tried removing and re-installing the utility to no avail. What do I have to do?

Hey HP ... Does anyone from HP monitor these posts and provide answers, as one might expect? Is anyone listening? Is anyone there? Does anyone CARE?

Cannot get Win8 Pro computer run the Connect a Computer to the Server Wizard (computerconnector) of Essentials 2012

I've spent 1/2 the day trying to troubleshoot this problem and finally give up.
My client has a Windows Server 2012 Essentials server (with all updates installed - no errors in error logs nor SFC /SCANNOW). Purchased a new Windows 8 Pro computer, which we installed all the updates from Windows Updates and are now trying to join
the domain using the "Microsoft way" (i.e.: http://[servername]/connect).
The site comes up and it prompts us to download the software and run... so far so good, but when we get to the screen where it asks, "Type your new network user name and password" - the next screen after that we get the error, "Cannot connect
this computer to the network...".
I've been looking at cases all day long through Microsoft and Google - all pointing to problems with the SSL on the server - that's not the problem here (as other workstations have, in the past, successfully connected and we verified today that the local
server certificate is what is the default, as it should be).
I've tried just about everything I can think of and cannot get this silly wizard to work (why Microsoft, WHY!??!?!). Yet, I can join this domain just fine doing it through normal means. I've even tried joining the domain this way, and tried installing
the software afterwards (as the Essentials Console won't reflect the new workstation, thus it won't add it to group policies etc... though yes, I could manually do that and have - but we'd still like to get it to show up in the console). I even
tried the trick noted in a KB talking about running the connect software without joining the domain (registry key that gets added) - that didn't work either.
I'm out of ideas - and at this point had to get the client online and working today - so we joined it manually, configured it and left it. But I would like to get this fixed the "proper" way. Help?
I do have the clientdeploy.log file - which only points out an internal error, but I'm unsure how to enable the improved logging it suggests (I'll gladly post the logs if someone tells me how - I'll skip posting the log file here for now):
[1544] 140204.203620.0794: ClientSetup: MachineIdentityManager.GetMachineStatus had errors: ErrorCatalog:NetworkError ErrorCode:-1
BaseException: Microsoft.WindowsServerSolutions.Devices.Identity.MachineIdentityException: MachineIdentityManager.GetMachineStatus ---> System.ServiceModel.FaultException: The server was unable to process the request due to an internal error. For more
information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in order to send the exception information back to the client, or turn on
tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs.
Suggestions? Thoughts? I hope Essentials 2012 R2 improves this - as I've had this error for other various reasons with other clients (and spent 1/2 days troubleshooting to clear those up). Essentials Connect, IMHO, needs a re-write - as
it's been nothing but a hassle... miss the SBS connect.

Hi slemay,
Before going further, please uninstall the Connector software from Control panel. Then connect again, will
the same issue persists? Would you please use another client to connect with the Server 2012 Essentials by using this way? Then monitor the result. Please make sure the computer has a physical connection to the local network.
Please refer to the TechNet article (Here)
and troubleshoot, then check if can help you to solve it.
In addition, please refer to the following articles and enable
WCF tracing to go further. Please check if you can find some clues.
How to enable WCF tracing
http://blogs.msdn.com/b/madhuponduru/archive/2006/05/18/601458.aspx
[wcf: solution] The server was unable to process the request due to an internal error.
http://blog.bitlinkit.com/wcf-solution-the-server-was-unable-to-process-the-request-due-to-an-internal-error/
Hope this helps.
Best regards,
Justin Gu

WRT610N - Cannot Get 5GHz Radio to Work

I have a WRT610N (firmware 1.00.00 B18), and I cannot get the 5GHz wireless radio to work under any mode (Mixed, A-Only, or N-Only). 2.4GHz radio works fine on all modes.
As far as I can tell, the 5GHz radio isn't even coming online. Settings are:
Wireless Configuration: Manual
5GHz Wireless Settings:
Network Mode: Mixed / A-Only / N-Only *
SSID: linksys-test
Radio Band: Auto / Standard / Wide **
Wide Channel: Auto (DFS) ***
Standard Channel: Auto (DFS) ***
SSID Broadcast: Enabled
2.4GHz Wireless Settings (Disabled)
* Tried all different network modes
** Tried standard for .11a and both standard and wide for .11n
*** Tried leaving on Auto, as well as forcing channels to 38, 46, 151, 159 (for wide) and 36, 40, 44, 149, 153 (for standard)
Tried with several different clients (MacBook Pro, various Dell and Lenovo laptop PCs), and none of them can detect anything at 5GHz from the WRT610N. All the clients are known to be working, as they are able to see other 802.11a and 802.11n (5GHz) wireless networks on other routers I'm testing (Apple Airport Extreme and D-Link Xtreme-N).
Could it be I have a broken WRT610N? Or is there some other setting needed to activate the 5GHz radio?
Thanks.

Why do you think that your 5GHz isn't coming online? Not all devices can connect to the 5GHz BAND. So if your trying to SEARCH for your 5GHz network and it's not showing up in the list along with your 2.4GHz network then perhaps your device doesn't support the 5GHz band.
For example, on a PS3 if you try to search for a wireless network, a PS3 will only find the 2.4GHz network because the card inside the PS3 doesn't support the 5GHz band.

I cannot get my iPhone 4S to show up in iTunes. (tried EVERYTHING!!)

Well, I've read countless threads about this.
However, NONE (and I repeat NONE) of those other options (ie: UpperFilter, reinstall, restart service, et al) are working for me. I am on my 6th reinstall
of iTunes, and I cannot get the thing to recognize my iPhone 4S.
Let me say, too, I *HATE* this newer version of iTunes.. (ok, that felt better!!)
I'm using Win7 system, everything is enabled. iPhone shows up in My Computer but NOT iTunes.
Please assist.. (oh, and please do not refer me to other threads..especially those pertaining to methods I've already tried and addressed). Thanks.

please look to your right in the More Like This box, or search this forum. Your question has been asked and answered multiple times already.

Cannot get n to enable.

Similar Messages

Maybe you are looking for