Cannot hear/monitor Centrance Micport Pro w/mic as input

LP8 Audio preferences shows CEntrance device as input.
LP8 Audio Midi Setup shows input as Centrance device.
Audio channel on record, with Input monitoring selected/record armed.
Cannot see or hear mic input through Mixer.

http://support.apple.com/kb/HT1215

Similar Messages

  • Device, driver loaded properly. Can hear through device 'phone input. Cannot hear through Logic Pro.

    I successfully loaded the driver to my brand-new Steinberg UR22 interface. The device shows up in Preferences > Audio as the input and output. I can hear a signal through headphones plugged into the headphone jack on the Steinberg.
    I cannot hear anything in Logic Pro, however. I've created a track, but cannot get my guitar to generate any movement on the LED fader on the lower left, or change rigs using the guitar amps/effects library on the right.
    What am I doing wrong?
    Why isn't there anything in the user's manual related to this?

    You've created an Audio Track, correct?
    Have you set the audio track to the correct input?
    The UR22's second (#2) input should be used with the Hi-Z switch enabled.
    Input gain at 1/2  also make sure the Master Output is up.
    You have a monitoring knob labeled Input/DAW
    If you wish to monitor both set the know to the halfway point, balance from that point.
    By Master Output I was referring to the Output level on the UR22
    Message was edited by: Pancenter

  • They cannot hear me

    when I call someone or receive calls sometimes caller cannot hear me.
    However, except calling mic works very well.
    I restored it to 4.3.2 many times without using backup but problem still occurs.
    Also, it happens with the original headphones.
    However, as I tried few times in my car, I have not face this problem with bluetooth kit.
    Is this issue software or hardware problem?
    This started to happen suddenly.
    Since, they give a refurbished one I do not want to go to technical service.
    I am from Turkey and using Turkcell.

    Also, it happens with the original headphones.
    However, as I tried few times in my car, I have not face this problem with bluetooth kit.

  • I have problem with my mic when i make call the others cannot hear me but the mic is ok

    i have problem with my mic when i make call the others cannot hear me but the mic is ok i checked it out and it works dont know what to do help me !!

    Hello Sabbir Khan,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Can't hear through the receiver or through speaker, and can't be heard
    iPhone: Can't hear through the receiver or speakers
    http://support.apple.com/kb/TS1630
    Best of luck,
    Mario

  • FaceTime - I cannot hear the other end at times and the mic now has a forward slash in front of it and I can't get it to go away

    FaceTime-at times I cannot hear - no audio - the person on the other end.  The mic now has a forward slash over it and I cannot get the slash to disappear.  At times I hear the other end even though the forward slash is still there.  I believe I have checked all of the settings.

    If they don't show up on screen captures, it's most likely a hardware failure. Make an appointment at the genius bar.

  • TS4185 I am having microphone trouble on face time.  Others cannot hear me.  I have checked system preferences and everything looks ok. Mic symbol has a line through it but nothing happens when I try to click on it.  Internal mic is selected.

    I am having microphone trouble on my Mac Book Pro during face time.  Others cannot hear me.  Microphone symbol has a line through it but will not allow me to change from muted to unmuted.  "Mute" under Video tab is greyed out and internal microphone is selected.  System Preferences show that internal microphone is working.  I have tried to restart computer, no difference.  Does anyone have a suggestion?

    When you have kernel panics, the pertinent information is in the panic report.
    These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad and start typing the name.
    In the Console window, select
              DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
    (not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar.
    There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
    If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
    In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
    Please don’t post other kinds of diagnostic report.
    I know the report is long, maybe several hundred lines. Please post all of it anyway.

  • 6300 receiving caller cannot hear me -random- Mic...

    I call someone and I can hear them fine but they often cannot hear me - t is a bit random .
    Is it a microphone problem?
    Replace?
    Mike

    Hi, i'm also having the same problem wth my 6300... can anybody help??

  • Cannot hear USB microphone in headphone

    I'm using the Logitech USB microphone which works fine for Skype and quicktime recordings. The problem is that I cannot hear the microphone in my headphones which makes it difficult to monitor the recording. The input volume level is working in System Prefs but I cannot hear the sound from the microphone. I also cannot record my side of Skype conversations with Wire Tap Pro since I cannot hear the audio from the USB microphone on the iMac. Any ideas?

    Edward Long wrote:
    Yes indeed, worked beautifully. Thanks for the prompt reply.
    You're welcome anytime.
    Glad to be of help.
    Have Fun
    Stefan

  • Regarding Facetime on my Ipad. I get started on a call and after 10 or 15 minutes I cannot hear whom I am talking to. They can still hear me and I still have picture on the screen but my sound stops working.

    Regarding Facetime on my Ipad. I get started on a call and after 10 or 15 minutes I cannot hear whom I am talking to. They can still hear me and I still have picture on the screen but my sound stops working.

    Why can't we use Acrobat Pro for mobile devices? Save a whole lot of headaches!!! Now I have to return this subscription.

  • People cannot hear me properly, problem with speaker?

    I think there is a problem with my phone when I talk to people, they say I sound like I am far away I have to shout, or cup my hand to the bottom of the phone in order for someone to hear me.
    I have done, i have restarted my phone, removed the battery, checked the settings. Still people cannot hear me. It has only been seven months, I never had a problem with my old BB Bold.

    First, make sure your mic isn't full of pocket lint. It's right below the "k" in BlackBerry on the front of the device.
    Then go to the Help app. At the bottom go to Testing. You can do different diagnostic tests in there and one of them is the mic. Does the test pass for the mic?
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

  • I cannot hear any sound on my laptop DV6 1030 us even though all my icons show that l should

    So, today just cannot hear a sound on it, all the icons are just as previous, they show l should, but no! I put the headphones in the sockets, nothing, when l put them in the mic socket, there l can hear just the noise that i insert something there. I can see the volume cursor going up down when l move it, but l don't hear anything... and nothing it's turned off.
     Can this be a virus?

    The internal speakers started working after uninstalling the sound drivers and restarted the machine, after which the system reinstalled the High Definition Audio Device driver, which was hitherto being used for the Headset speakers.
    Today, the external speakers (the ones used by the headset) stopped working. Both the internal and external speakers
    have the same High Definition Audio Device driver. Both are showing "device is working properly", but when the headset is plugged into the two jacks (in and out), the sound does not come from the headset earpiece, but from the internal speakers (ie the loudspeakers).
    Any solution for this ? 
    My wife's machine has been having a similar, though not identical problem, since the last couple of weeks. In her
    case, when the headset is plugged in, there is no sound at all, neither from the headset speakers, nor from the internal speakers. 
    Just to eliminate the possibility of the headsets malfunctioning, I tried using another headset, but with the same
    results as above.
    All these audio problems started a couple of weeks ago, after a Windows overnight update, as detailed in my opening
    post under this thread.

  • Cannot hear anything in calls only. Works for Skype.

    Hi,
    I am facing a strange problem. I cannot hear anything when making or receiving a call. Neither the earphone or speaker would work. The person on other side can hear me so the mic is working. Strangely this seems to be only a problem while calling via network. Can use facetime, Skype, play music. So assuming there is no hardware issue.
    I have tried restarts, restoring to factory settings, none have helped.
    Any idea or help will be greatly appreciated.
    Cheers
    Say

    I am having the same problem. Did you ever get this resolved?

  • TS3367 PEOPLE WHO I FACETIME CAN SEE ME BUT CANNOT HEAR ME.

    I am having trouble with the audio on facetime. I can hear and see folks I facetime. These folks can see me BUT they cannot hear me. what do I need to do?

    I saw one post where the user said that dust got in the Mic hole. Vacuumed it and restored the audio.
    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
     Cheers, Tom

  • Cannot hear channel 3 & 4 in FinalCut

    I put music on channel 3 & 4. The audio meter shows me the audio level but I cannot hear it. Have checked all settings and cannot find what I am missing. Anything that I put on channel 3 & 4 cannot be heared but meters shows level. How do I hear channel 3 & 4?

    I am putting music on channel 3 & 4. It is in a sequence in the timeline.
    It is an aif file. Not recording from deck. I see the audio levels from the meter but I cannot hear the tracks.
    I am able to hear channel 1 & 2 from the computer and see them on the audio monitor within finalcut but not 3 & 4.
    So finalcut is showing me it is something there.
    Original question
    Cannot hear audio on channel 3 & 4 in finalcut

  • People cannot hear me properly

    Im having issues with my iphone 5 where by i can hear people perfectly well but after a couple of minutes conversation they cannot hear me properly, they miss out on words and sounds stuttery. Not sure if its related but only the left headhphone will work now too, i have tried another set and get the same problem
    Any ideas appreciated
    Thanks

    First, make sure your mic isn't full of pocket lint. It's right below the "k" in BlackBerry on the front of the device.
    Then go to the Help app. At the bottom go to Testing. You can do different diagnostic tests in there and one of them is the mic. Does the test pass for the mic?
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Maybe you are looking for