Cannot load two cdrom drives, (code 10)

if i try to have two cdrom drives running at the same time, a dvdrom drive and a cdrw drive, the cdrw drive has an error. it says "This device cannot start. (Code 10)" how can i fix this?
If i try to use either individually it will work, i don't understand what Code 10 is though.

I have major probs with ide as well when I have all of the slots filled. I have an 80 gig and a 20 gig as well as a cd reader and writer. When I used the 20 gig attached (a fugitsu) in several differant place once as slave to the 80 and then as master to the writer after a couple of reboots I noticed that when the fugitsu was getting listed by the bios something strange happened it showed up in upper and lower case letters. I never saw that happen before but after I noticed it I could no longer access the drive in windows and the bios detected it as a 14? gig drive using auto and trying it manually. This occurred twice and on differant channels. This did not correct itself by resetting the bios or shutting down the power. I was only able to correct it by physically removing the drive. I put back and it was normal again but it did it again later so I just pulled it. So in my opinion this board has some ide issues in addition to being one of the most picky boards I have seen when it comes to slave and master position on the cables. And theres another joke why in gods name is the master supposed to be attached on the end of the ide 80pin cable when in every computer the hd is below the cdr makes thing a real pain in the ass.
ps the iomagic 24x10x40 drive is a btc remark and I am using it again due to its ability to burn safedisk2 cd's but I liked the 20 gig to boot into linux becuz the 80 gig has probs with grub and lilo and trying to "correct " made XP unbootable and partition magic choked as well

Similar Messages

Windows cannot load the device driver for this hardware. The driver may be corrupted or missing.

I'm having the error "Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)" and I can't read/write CDs/DVDs. When I try to update the driver I have the message that it is already up to date.
I can't find the driver to dowload and try to fix the problem. Where can I download it or solve somehow my problem?

Hi juigarashi,
Microsofts automated troubleshooting service on the link below may help
CD/DVD Repair
Hope it works for you.
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Cannot bootup from cdrom-drive or from harddisks

This is quite a post, main point is: I cannot succesfully bootup my desktop from either a cdrom or my hard disks after a normal reboot. After a cold reboot (power off for about 30-40 seconds) it will bootup but will randomly reset or freeze up.
It started with me browsing a website with chromium-svn, chromium told me that the website might contain malware, but I wasn't really worried since I was using linux and browsing under a normal user account. Then a java window popped up, something concerning settings, and my system became very slow. I tried to click away the java window but my X server crashed and put me back into KDM. I fired up a console (Ctrl+Alt+F1) and did "ps aux" to see if my system was compromised and strange processes were running. That wasn't the case, but as soon as I logged out the terminal disabled itself claiming it had too much input or something like that (it's a couple of days ago I don't remember the details). So I resetted my desktop and now grub wouldn't start up. It just gave a strange character in the top left corner and froze up. A cold reboot did give me grub back, but it wouldn't let me into linux, somehow my partitions wouldn't mount. After that I tried my windows XP dual boot, that worked althrough it suffered from random resets.
Thinking something was wrong with my harddisk I tried rebooting with Parted Magic livecd. That failed, as did rebooting with the official arch livecd and with several other livecds. All giving some fault that they couldn't find/mount the cdrom, while the innitial bootup from the cdroms all went good. A cold reboot fixed that problem, but all suffered from random resets and lock-ups.
After that I thought is was a hardware component, so I tried pulling them out one by one to see what the problem might be. It wasn't the harddisk, for I nuked the partition table and pulled it ou (I have two harddisks, so pulling one out is a possibility). I also replaced the cdrom drive. Then I pulled out a new memory module (I bought one a few weeks ago) to see if that was the problem, but it wasn't. I also updated the BIOS to see if the problem was there, but to no avail. As a last ditch effort I replaced the CMOS battery and resetted the BIOS properly. But all had no effect.
I runned Memtest, but it detected no errors. Currently I have no idea what is wrong other than that it is broken. By process of elimination I'm fairly confident that it isn't the harddisk, nor the cdrom-drive nor the memory.
During the bootup from the archlinux install cd the kernel messages do indicate that it detects sda as a harddisk and sdb as a cdrom drive, while I have 2 harddisks and one cdrom drive. So it should detect sda and sdb as harddisks and sdc as a cdrom drive. Also it gives the following error:
waiting for boot device
error: boot device didn't show up after 30 seconds
And also:
usb 2-2: device description read/64, error -71
and much more of that with errors: -110, 1790, -22
Also this:
hub 5-0:1.0: unable to enumerate USB device on port 2
My hyphothesis is that my southbridge (which deals with the cdrom, harddisk drives and the usb devices) is somehow broken.
I'd like to have your oppinion on this, or at least confirm if my cdrom, harddisk etc. really aren't culpable in this problem so I might reuse them. Right now my solution would be to buy a new motherboard/CPU/memory and reuse all the other components.
EDIT: My hardware is:
CPU: AMD Athlon64 3500+
Motherboard: Asus A8V-E SE (Northbridge: VIA K8T890 | Southbridge: VIA VT8237R )
Memory: 2 GB
HDD: 2x SATA-150
CDROM: DVD-writer
System ran ok from 2006
Last edited by Chromoris (2009-12-17 04:38:06)

Well your testing and conclusion seem correct, but maybe before buying new stuff, try booting those drives using a different machine, if there are no problems... then go ahead and get the new board.
Testing the drives with a different machine will need to wait untill after the holidays. However the disks are not that old, one is almost brand new, and nothing has given me an indication that something is wrong with the disks itself. So I think it is a safe assumption that the disks themselves are good, but it won't hurt to check I guess.
Remove the hard drives (or at least their cables) and boot a Live Linux CD from the CDROM drive. Same issues? If yes, and you have checked memtest as you said then either you have a motherboard or CPU fault. At that point remove your CPU and renew the heat sink compound and reseat the CPU. If that does not work probably a motherboard fault as you suspect.
Removed the cables and booted with a Live CD, problem remained. Althrough this time I've been rewarded with a kernel panic, still couldn't find the booted cdrom device. I renewed the heat sink compound a few months ago so I'm fairly confident it is still good. I did that because my CPU overheated, and I've kept a good eye on the temperature sensors ever since. Besides I know what happens if my CPU overheats so I'm pretty sure it is not overheating. Should the problem be a broken CPU, well that would almost be the same as a broken motherboard and I would have to replace both of them. I cannot easely find replacement parts for either the cpu or the motherboard, socket 939 has become obsolete.

Cannot load a FAx driver for a Hp Laserjet 1536dnf MFP on a HP Pavilion Elite e9220y Computer

I cannot find a fax driver for this printer to install on my computer.
I have uninstalled and reinstalled the printer a couple of times It will print and scan but not fax.
I reinstalled fron the orignal disk and off the HP website neither get me fax capablilites.
I have gone to support and cannot find the drive on eith er the printer or computers web page at HP.Com
Please let me know what to do.

Hi @thesaneone4 ,
I see that you are experiencing issues with the fax driver not installing. I would be happy to help you.
Check the connections in the Device Manager for any printer entries, under Universal Serial Bus Controllers look for Fax LEDM or any unknown devices. Right click and try to update the driver. How do I get into Windows Device Manager?
In the Devices and Printers window, what icons do you have for the printer showing?
If you are still having issues, you will need to uninstall the printer software from the CD and unlock the hidden Admin Account when installing the printer software, to make sure there isn't any interference.
Disconnect the USB cable.
Uninstall the software by going to Start, Computer, right click on the CD and open it, then double click on uninstall.
Then download and run the latest software. HP LaserJet Pro M1536dnf Multifunction Printer.
Unlock Hidden Administrator Account and install the printer on this account:
Go to your Start menu and under the 'search programs and files' box type CMD.
CMD will populate as a search option above, just right click on it and 'run as administrator'.
Once CMD (Command Prompt) opens, type net user administrator /active:yes and hit enter.
Next, close CMD and restart your computer.
When your computer comes on log into the new account that should show. It will be called Administrator and will not have a password on it.
If your computer automatically logs into your account after restart than go to your start menu click the arrow beside 'shutdown' and choose 'switch user'. Now log into the Administrator account we just unlocked.
Under the Administrator account, install the printer software.
Test the printer.
To turn off the Admin account start back at step 1 and type in net user administrator /active:no.
Please let me know the outcome.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

E70: cannot load IR modem driver

I upgraded the FW to the latest version, I have the latest PC Suite installed and still I cannotuse the E70 with my laptop for dialup GPSR connections. It seems PC suite does not automaticly install the correct drivers for IR modems. I now use the standard one, but I get the message 'cannot connect to the network'. If I go to the option, I only can pick the 'standard modem over IR link'.
On the Nokia site there's a special IR-driver ( an inf.file) for the E70. I downloaded this but it will not install. Even if I try all the basic windows setup install procedures this file is refused. It is seen OK if I go the the option where you select your own drivers, only it will not install. A totally mysterious thing. Is the file corrupt? Is something wrong with my W2K-version.
I remember I had this thing before with other drivers, but one way or the other I always managed to get around this. Now I can't find a solution. Trouble is I cannot use the E70 to connect my PC to the web while I'm traveling.
Anyone with a brilliant solution??
(PS. I don't want to use a cable and I don't want to use bluetooth. I want to get the IR-link working on the E70.)Message Edited by rusco on 25-Oct-2006
05:22 PM
Owner Nokia 520 (experiment: serious problems connecting pop accounts).
History: Siemens S4, Sony Z1, Ericsson SH888, Siemens s40, Nokia 6230, Nokia E70. Nokia E71-1, E72-1, HTC Wildfire (good stuff), HTC One V (also nice).
(And sometimes I still miss my Psion Revo! ;-)

Took a while, but I tried the USB cable and with this connection I have no problem making contact with T-mobile.
So I still don't understand. How can I actually change the standard IR-modem driver thatis included in the Nokia Suite with the special E70 modem driver that I already downloaded? I hope some Nokia E70-W2K specialist has a good tip!Message Edited by rusco on 22-Nov-2006
06:15 PM
Owner Nokia 520 (experiment: serious problems connecting pop accounts).
History: Siemens S4, Sony Z1, Ericsson SH888, Siemens s40, Nokia 6230, Nokia E70. Nokia E71-1, E72-1, HTC Wildfire (good stuff), HTC One V (also nice).
(And sometimes I still miss my Psion Revo! ;-)

Cannot load or find Driver, Port_#0005.Hub_#0004

Hi all,
I just installed a new sdd and I'm reinstalling all my drivers but I can't seem to find one driver. It says it is in, Port_#0005.Hub_#0004. My computer is a T510 (4313). I've tried windows update and the lenovo drivers update as well and neither one works for me.
Thanks for the help.

Hiyomika wrote:
Hi all,
I just installed a new sdd and I'm reinstalling all my drivers but I can't seem to find one driver. It says it is in, Port_#0005.Hub_#0004. My computer is a T510 (4313). I've tried windows update and the lenovo drivers update as well and neither one works for me.
Thanks for the help.
What I would try (in this order) is a Bios update, Chipset Driver Update and then uninstall all of the USB hubs appearing in Device Manager, reboot. Run the Thinkvantage System Update last to do a cleanup. That SHOULD catch it

Cannot load device driver for DVD/CDRW - Satellite 1110

I have a Satellite 1110 and something has gone wrong with my DVD/CDRW and it will not read any CDs. It is reported as a MAT****A UJDA730 DVD/CDRW but the device status comes up as:
"Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)"
I have tried uninstalling and reinstalling the device but the error just returns. I cannot find a driver for it either on the manufacturer's web site or Toshiba's. I don't want to use the Product Recovery CD-ROM as it implies I will lose all software and data on the hard drive.
Can someone advise how to recover from this situation?
Thanks

Hi
Firstly you dont any driver for the CD/DVD drive. The drive uses the standard Windows OS driver and its not necessary to install it additional.
I assume there could be something wrong with the registry entry.
Please check this forum posting:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=13843
The user has used the instruction which was offered on the Microsoft site.
This should help.
Please post again if this method was successful.

Cannot load device driver

Hello, After upgrading to Windows 7 Ultimate, my drive quit working entirely. The description reads: "Windows cannot load the device driver for this hardware. The driver may be corrupted or missing". I've downloaded updates and don't know whether I should uninstall or what... please help
This question was solved.
View Solution.

Hi,
First, try the automated fixit from Microsoft on the link below.
Windows 7
Check if the drive is now working.
If the drive is not working, from the Start Menu, open the Control Panel and click on Device Manager. Click to open the IDE ATA/ATAPI Controllers. Right click on the first channel and select uninstall. Do not delete drivers if asked. When uninstalled repeat the process for each channel. Also if an ATA controller is listed, right click and uninstall this, again not deleting drivers if asked. Then open DVD/CD-ROM Drives. Right click the drive and select uninstall. Do not delete drivers if asked.
Reboot the PC and let Windows reinstall the devices. Check the drive again.
If it still isn't working, run the automated fixit from Microsoft on the link below again.
Windows 7
Next, from the Start Menu, open the Control Panel and click on Device Manager. Next click to open DVD/CD-ROM Drives. Right click the drive and select uninstall. Do not delete drivers if asked. When the device has uninstalled click on the 'Scan for Hardware Changes' icon ( usually just below Help on the toolbar ). Let windows reinstall the drive and see if it now works.
Best wishes,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Equium - Windows can't load the device driver for USB dongle

I have been using a dongle without problems for about a month, however now it is saying (in device manager ) "Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)"
what does this mean and how can i fix it?

hi it's a vodafone 3gb cheap as chips dongle
it's an equium a200 i think
everything cam as one on the dongle, it uninstalled ok after initial problem, but now won't acknowledge it is in fact a dongle, just a 'usb mass filter' something or other?
i know i sound completely stupid, but when it comes to technology i am!

No sound on Equium - corrupt or missing driver (Code 39)

Hi
My name is Samee.
I have recently wanted to play music on my computer using windows media player but no sound comes from the speakers of the laptop, I have checked device manager and there is a minus sign next to sound, video and game recorders when I scroll down the is a yellow circle with an exclamation mark next to the device "Microsoft kernel wave audio mixer". When trying to play the music track my windows media player 11 it says
"Windows media player cannot play the file because there is a problem with your sound device. There might not be a sound device installed or it might be in use by another program, or it might no be functioning properly''.
When I try to uninstall the device and then scan for new installed hardware it gives me an error message
"Windows cannot load this device driver for this device the driver may be corrupt or missing. (Code 39)''
Is there any way I can make my speakers function again if so how?
Thanks Sam

i have first uninstalled any sound driver installed in the computer and then reinstalled the drives via the software CD provided by the computer manufacturer. after doing this it did not seem to resolve the problem, therefore i then had to lake a last resort and reformat the HDD. but after doing this i the sound drive was working correctly but i ran into another problem when installing windows xp service pack 2. It failed to install no error code came up.
can anybody tell me how to get out this mess.
sam

Satellite A205-S6808 corrupted DVD/CD-ROM Driver - Code 39

My driver is corrupted for my CD-ROM/DVD player.
There is absolutely no support for my model on the Toshiba homepage.
I tried to download the drivers for the L series L505 since my tech friend said it should have worked. It did not.
The device shos up, but I get a driver missing/corrupted message from windows.
I am running win 7 32 bit and the DVD player is the same one that came installed when I bought the laptop.
This is the message I get "Windows cannot load the device driver for this hardware.
The driver may be corrupted or missing. (Code 39)"
CAN ANYONE HELP??

Hi
Im a little bit confused how you have managed to download the CD/DVD driver for the internal ODD (optical disk drive).
The point is that all Windows operating systems contain own Microsoft ODD driver which controls the CD/DVD drive.
Therefore its not necessary to load/install any drivers for CD/DVD drive.
In my personal opinion its a registry issue.
You should firstly go to the device manager and should remove the CD/DVD drive from the system.
Next step is registry cleaning.
Start regedit and remove the Upperfilters and Lowerfilters values completely from the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
After that reboot the unit
Should work
Greets & Good luck
PS; This is an US notebook model and all drivers can be found on Toshiba US page.

Loading Sharp printer driver on iMac

Hi, I have just come back to Mac after 15 years and in setting up my new computer, I cannot load the Printer Driver for a Sharp ARM205 laser printer. I have downloaded the latest Mac driver from Sharp and I can see the file in the Downloads Folder but cannot work out how to load it. The computer can see the printer but with no driver, no printing after many attempts. Any tips appreciated.

Hello and welcome back to Mac
If you select the driver file in Downloads and perform a Get Info (Command I or File > Get Info), the Get Info will show you under the heading of Name & Extension what format the file is. Note that you may need to click the little triangle next to Name & Extension to expand the view.
With OS X 10.5 and 10.6, there is a built in function to create a compressed zip file. If this is the extension of the driver, simply double click to decompress the download. It will automatically create a folder for the driver in the same Downloads folder. If the file format is something other than zip, you may need Stuffit or something similar to unpack the file. Please reply with the extension name.
Also, under the Name & Extension menu is the Open With section. If you expand this entry, you will see what application on the Mac is set to open these files types. If no application is listed, then as mentioned already you may have to download a utility to unpack the file.
Pahu

Cannot load MIB on HUM

Hi all,
I am trying to load CISCO-VOICE-DIAL-CONTROL-MIB to HUM. Bu I cannot load two of the dependencies: DIAL-CONTROL-MIB and INT-SERV-MIB.
Although all the dependencies of these two mibs are laoded, when I try to load these two mibs, I get the error "Unable to load the MIB file. Either you are trying to load an invalid MIB file or the dependent MIB files are not available in the path."
What can be the cause of this problem?
Thanks...

Don't try loading all of the dependencies. Just make sure they are all in the mibs directory. Then, replace your CISCO-VOICE-DIAL-CONTROL-MIB.my file with this one. Then just try loading the CISCO-VOICE-DIAL-CONTROL-MIB.my directly.

Java.sql.SQLException: Cannot load JDBC driver class 'null'

Hi,
I am a beginner of using jdbc, i use the tomcat4.1.x, mysql3.23.54 and it's jdbc driver 2.0.14. I place the drive <in jar file> in tomcat/commons/lib and configure the server.xml, web.xml and some testing coding. But there are some error like the following:
java.sql.SQLException: Cannot load JDBC driver class 'null'
     at org.apache.commons.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:529)
     at org.apache.commons.dbcp.BasicDataSource.getConnection(BasicDataSource.java:312)
     at foo.DBTest.init(DBTest.java:18)
     at org.apache.jsp.test_jsp._jspService(test_jsp.java:48)
     at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:136)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:204)
     at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:289)
     at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:240)
of course its some of the error code and there are more.
Why I have this problems and how can I fix it? Can someone help me??
Thanks,
Tong
I place my test.jsp at tomcat/webapps/DBTest and DBTest.java at tomcat/webapps/DBTest/WEB-INF/classes/foo
additional of the tomcat/conf/server.xml
<Resource name="TestDB" auth="Container" type="javax.sql.DataSource" description="MySQL TestDB"/>
<ResourceParams name="TestDB">
<parameter><name>factory</name>
<value>org.apache.commons.dbcp.BasicDataSourceFactory</value>
</parameter>
<parameter><name>maxActive</name><value>10</value></parameter>
<parameter><name>maxIdle</name><value>1</value></parameter>
<parameter><name>maxWait</name><value>10000</value></parameter>
<parameter><name>username</name><value>javauser</value></parameter>
<parameter><name>password</name><value>javadude</value></parameter>
<parameter>
<name>driverClassName</name>
<value>org.gjt.mm.mysql.Driver</value>
</parameter>
<parameter>
<name>url</name>
<value>jdbc:mysql://localhost:3306/javatest?autoReconnect=true</value>
</parameter>
</ResourceParams>
tomcat/webapps/DBTest/WEB-INF/web.xml :
<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE web-app PUBLIC
"-//Sun Microsystems, Inc.//DTD Web Application 2.3//EN"
"http://java.sun.com/dtd/web-app_2_3.dtd">
<web-app>
<description>MySQL Test App</description>
</web-app>

Post the part of your code that loads the driver and connects. My guess is you are using a variable for the name of the driver and the variable has not been set to anything(intially set to null).
Thanks
Cardwell

Java.sql.SQLException: Cannot load JDBC driver

THis topic has been discussed many many times but I still not able to connect to Oracle 8i from my servlet using Tomcat 4.1.12 on hp-ux and java1.3
I always got: java.sql.SQLException: Cannot load JDBC driver class 'null'
In server.xml:
<Context Path="/MyApp" docBase="MyApp" debug="0" reloadable="true" >
<Resource name="jdbc/ora" auth="Container" type="javax.sql.DataSource"/> <ResourceParams name="jdbc/ora" >
<parameter>
<name>username</name>
<value>myname</value>
</parameter>
<parameter> <name>password</name>
<value>mypassword</value>
</parameter>
<parameter> <name>driverClassName</name>
<value>oracle.jdbc.driver.OracleDriver</value>
</parameter>
<parameter>
<name>url</name>
<value>jdbc:oracle:thin:@myhostname:1521:ora</value>
</parameter> </ResourceParams>
</Context>
In MyApp/WEB-INF/web.xml:
<resource-ref>
<res-ref-name>jdbc/ora</res-ref-name>
<res-type>javax.sql.DataSource</res-type>
<res-auth>Container</res-auth>
</resource-ref>
The Oracle jdbc jar file classes12.jar is under common/lib in Tomcat's home. read Permission is there.
In the servlet:
init(ServletConfig config):
Context init = new InitialContext();
Context ctx = (Context) init.lookup("java:comp/env");
dataSource = (DataSource) ctx.lookup("jdbc/acdb");
doPost(..)
the error occured at :
synchronized (dataSource){
con = dataSource.getConnection();}
Thanks in advance!

Everything looks correct to me, except for one thing.
In your web.xml you have this:
<res-ref-name>jdbc/ora</res-ref-name> In your server.xml, you have this tag, which matches your web.xml:
<ResourceParams name="jdbc/ora" > But in your Java code, you've got this:
dataSource = (DataSource) ctx.lookup("jdbc/acdb"); When I've successfully set up a Web app data source, all three names had to agree. You either need to change your Java lookup name to "jdbc/ora" or change the web.xml and server.xml to "jdbc/acdb".
See if that does it. Everything else sounds correct to me. - MOD

Cannot load two cdrom drives, (code 10)

Similar Messages

Maybe you are looking for