Cannot load windows 2000 (sp3) on pm8m2-v with single sata drive

I'm using a single WD 80GB SATA Drive (wd800jd) on the pm8m2-v mainboard's via sata controller. I've gone through the hit F6 and selected the windows 2000 ata/atapi driver and the raid driver (both separately) and the OS install always says it finds no hard drive. Then I tired both ata/atapi and raid driver for windows xp (even though i'm attempting a windows 2000 install) and it actually finds the drive, but after formatting and copying files, i get an inaccessible boot device failure when it reboots to begin setup. i've downloaded most recent mobo drivers and bios (the bios on the web is actually older than the one on the board? - web has v1.1 and the board has v2.0) ideas???

got it workin with the most recent xp driver from the site... strange

Similar Messages

Cannot load windows xp but windows 98 runs fine with KM4M-V

Why wont windows xp load into my new motherboard when windows 98 runs fine.
AMD Athlon 2400+
256 mb ram
80 gb Seagate baracuda

As I first said I cannot load windows xp but windows 98 runs fine.
I have formated the drive into ntsc and fat 32 but as soon as the setup process has finished in xp and it wants to load the system posts the Blue Screen of death.
Why does windows 98 run without any problems .I have checked memory ,ram,pro and hdd but all are fine.This one puzzles me!!!.
I understand from other feeds it could be the power supply not beefy enough but if that was the case why does windows 98 run so well??
Amd Athlon 2400+
Seagate Baracuda 80gb
Seimens 2100 ddr total 768 on two sticks
DVD rw-
dvd rom drive
FSB Power supply 250watt
3.3v - 16a
5v - 25a
12v - 13a

Resource Conflict – Serial Bus Controller & PCI Bus Issues - Cannot Load Windows 7 - PLEASE HELP!

Anyone have any ideas about a remedy? I am ready to toss it and purchase another. THANKS! HP Pavilion Notebook, dv9827clAMD Turion 64 x 2, Bios F.34Windows 7, SP 1 (Upgraded from OEM Vista SP2) PROBLEM: This morning my system has a blank illuminated screen. Upon power-on, the system eventually goes to the blank screen. Can get to BIOS functions, but beyond that it will not load Windows 7. System was working with Windows 7 prior to this issue. No recent changes or updates made to this system. Stationary - No physical abuse. Five (5) years old. Upon power-on, the screen gives PF keys, which enable me to enter the BIOS: F1 – System Information > Clock still has correct date and time. F2 – Startup Check -> Both HD and RAM OK F9 – Change Boot Device Order -> Can change device order, but it still won’t boot or respond to a System Recovery DVD in a USB DVD. ( Notebook DVD stopped working before this problem happened.) F10 - Enter Setup F11 – System Recovery – Two choices, but <enter> and arrow keys do not work. (They DO work with other F-selections, but not with F-11 menu) (1) Continue with System Resume (2) Delete Restoration Data and Proceed to System Boot OTHER OBSERVATION: When access PF1, I get the BIOS. If I exit and save with PF10, I get a brief flash of error messages, then it goes back to the PF-selections and eventually to the blank screen. Here are the error messages:Bios Version F.34ERRORResource Conflict – Serial Bus Controller on MotherboardBus 02 Device 05 Function 00ERRORResource Conflict – PCI on MotherboardBus 02 Device 05 Function 01ERRORResource Conflict – PCI on MotherboardBus 02 Device 05 Function 02ERRORResource Conflict – PCI on MotherboardBus 02 Device 05 Function 03ERRORResource Conflict – PCI on MotherboardBus 02 Device 05 Function 04 OTHER ACTION: Tried a hard reset = Removed battery, held down power key about a minute, but no effect. The data part of the HD is ok. I can remove the hard drive and put it in an enclosure, then access the data with another computer.

Hi!
I have exactly the same problem on my HP dv6750, but I can't find an answer that really help me to solve it.
Well, this post shows the description of my problem, so, I don't want this question dies.
If somebody have the solution, please, help me to bring my laptop back to life again.
Thanks

HT1338 how do i load windows 7 on a mac air using the super drive?

How do I load windows 7 on a Mac Air using the super drive?

You use Boot Camp to partition the SSD in the Air, download the Win 7 Support files from Apple (part of the boot camp process), save them to a USB thumb drive, have the USB superdrive connect to the Air with the Win 7 install DVD in the drive. Once partitioned the system will reboot and start the Win 7 install.

How to install Windows XP on a single SATA drive?

I am trying without much success to use a single Maxtor 200 GB SATA drive in a non-RAID configuration running Windows XP Home SP 2+. I obtained documentation from the MSI Download site that explains how to do such a thing. However ...
First, out of the box the Drivers & Utilities CD is useless -- can't read it, simply hangs the CD drive.
Second, the drivers from the Download site (IATA_ICH5R) return "incompatible hardware. software not supported on this chipset" messages.
So where do I get the drivers required to install Windows XP on a single SATA drive (to use at point F6 in the Windows XP installation)?
Regards,
Bob (ll1951md)
P.S. Configuration ...
865PE/G Neo2-P (MS-6728) w/ Intel Extreme Graphics 2, Realtek ALC655 Audio
2 GB Corsair Dual Channel DDR Memory
Intel P4 3.0e GHz Processor
1 Maxtor 200 GB SATA HD
1 HDS 120 GB ATA HD

Thanks for the tips. I was able to install Windows XP and boot from the SATA drive by using these options and setting the appropriate boot device selections...
Legacy Mode
ATA Configuration - PATA only
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
Combined Mode Option - S-ATA 1st Channel
S-ATA Ports Definition - P0 - 3rd./P1 - 4th.
I just wasn't sure if I was really getting "SATA" performance, etc. without specific drivers.
Thanks again.
Bob (ll1951md)

Webcam NX Ultra cannot load windows 7 drivers

Hi please help - I was so excited to see the windows 7 drivers for my webcam NX ultra - but I cannot load them . Installation wizard gets to a certain point and then it says driver installation failed. I have tried unistalling the camera, unistalling anything with creative in the title in my registry - always same result installation fails - PLEASE HELP - if I cannot get this to work I will bever buy another creative product - my logitech camera which is 5 years older has windows 7 drivers and works fine. Com-on creative get with it

Here
http://support.creative.com/Products/ProductDetails.aspx?catID=218&CatName=Web+Cameras& subCatID=219&...
but I see now it was not for windows 7 - it comes up when you do search and windows 7 guides you to the page...
Looks like I will just buy logitech products in the furure :-(

Error installing Sun ONE Directory Server 5.2 under Windows 2000 SP3

Hi,
When I attempt to install the Sun ONE Directory Server 5.2 under Windows 2000 Server SP3, I get the following errors:
Installing Sun ONE Server Basic System Libraries
Installed:C:\WINNT\system32\icudt2.dll
Installed:C:\WINNT\system32\icuin2.dll
Installed:C:\WINNT\system32\icuuc2.dll
Installed:C:\WINNT\system32\libadminutil52.dll
Installed:C:\WINNT\system32\libadmsslutil52.dll
Uninstalling C:\WINNT\System32\icudt2.dll
Uninstalling C:\WINNT\System32\icuin2.dll
Uninstalling C:\WINNT\System32\icuuc2.dll
Uninstalling C:\WINNT\System32\libadminutil52.dll
Uninstalling C:\WINNT\System32\libadmsslutil52.dll
Uninstalling C:\WINNT\System32\libnspr4.dll
Uninstalling C:\WINNT\System32\libplc4.dll
Uninstalling C:\WINNT\System32\libplds4.dll
Uninstalling C:\WINNT\System32\nsldap32v50.dll
Uninstalling C:\WINNT\System32\nsldappr32v50.dll
Uninstalling C:\WINNT\System32\nsldapssl32v50.dll
Uninstalling C:\WINNT\System32\nss3.dll
Uninstalling C:\WINNT\System32\sasl32.dll
Uninstalling C:\WINNT\System32\smime3.dll
Uninstalling C:\WINNT\System32\ssl3.dll
Product Install Failed: java.io.FileNotFoundException: C:\WINNT\System32\libnspr4.dll (Access is denied)
I've checked, and this file does not pre-exist under WINNT\System32.
Any ideas why I'm getting this error? Is this a bug in the installer?
Cheers,
Scott

IIRC this file, sasl32.dll, should get installed onto %WINDIR%\system32 when you install DS5.2 windows version.
You may run WinZIP and File/Open "d52diu.zip" (DS5.2 zip image) and look for "nsbasesys.zip", double click to Open it and you should find "sasl32.dll" there.
Gary

Windows 2000 (SP3) crashes on K7T Pro

Hi
I have a this configuration:
K7T Pro (BIOS 3.6)
Athlon 1200
256 Ram pc 133
Geforce 3 ti200 detonator 40.71
hdd 20gb maxtor
Windows 2000 with SP3
directx 8.1
4in1 drivers
the problem is windows hangs and the 4 back leds turn all green on any application and more specially on games like quake 3, i want to know if its caused by some drivers? or do i need to install a patch for windows 2000 that fixes some AMD issues or mobo problems?
help would be apreciated

Sure you can Install a lv application manually. just copy the exe-file,
support files in a folder. For the runtimeengine just copy the file
lvrte.dll in the folder of your application or in the windows system folder.
Hope that helps, Niko
BB Herman wrote:
> Why will a stand alone executalbe with an installer work on windows
> 2000 and crashes on windows xp professional?
>
> When I run the setup.exe file on a Windows 2000 system it installs
> properly, but the same file run on a XP Professional system I get an
> error stating Fatal Error: Installation ended prematurely because of
> an error.
>
> See
> HREF="http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000...
for more information on the specific installer I'm trying to
> use.
>
> In fact I get this error for any stand alone executable I try to
> install on any XP machines. I am using LV 7.1. Is there a way to
> manually install everything?
>
> Thanks

IPod Touch: charging with Windows 2000 SP3?

Hello,
I've got an iPod Touch 2nd generation, and I'm a mac user.
At work, I have a Windows 2000 PC, Service Pack 3. I wanted to use this windows machine to charge (with USB) my Touch, but it didn't work directly. So I tried to download iTunes, but it requires SP4 at least.
What can I do? The PC isn't able to give energy to the USB port, if the device isn't recognized?
Thanks for any help
Frederic

The following applies to XP and I assume Vista, but I am not sure if this option was in 2000 or not. But you can check...
Well one thing you can try it telling you computer to leave the USB ports on all the time. XP (and I assume Vista) has a power saving mode where the USB ports are powered down if they are not in use by the operating system. I think that is the default mode. This is more of a setting beneficial to Laptops, but if you have a desktop, you might want to disable to power saving modes.
Start -> Control Panels -> System -> Hardware tab -> Device manager
In the window that opens, expand (click on the sign) next to Universal Serial Bus Controllers
You will see a number of things in that list. You want to RIGHT-Click on the "USB Root Hub" one. I am not sure if you have more than one if they still point to the same one, but open and change each to be sure. Anyway, right-click it, in the pop up menu pick Properties. In the next screen, pick the Power Management tab. There is a check box to "Allow the Computer to turn off this device to save power". I think default is checked, so that the ports power down. You want to unselect that box forcing your USB ports to stay powered up all the time.
Patrick

Cannot load windows 7 through bootcamp

i have been trying to load windows 7 through bootcamp. but after the initial partition process, the screen goes blank with a cursor on the top left corner.
it does not come to life even after 4 hours.
i did not have any problem making the partition before. this is the first time i have had this issue.
can anybody help?????

I just successfully installed Windows 8.1 Update 1 on BootCamp on Mac OS X Yosemite. Here is a step by step I just wrote, hope it helps y'all:
How to successfully install Windows 8, or above, on Mac OS X Mavericks or above:
Requirements:
1- Windows OS ISO Image file
2- An 8GBs USB Flash Drive
3- A good Internet connection as you will need to download the Windows compatible drivers for your Mac
Steps:
1- Open up Disk Utility and create an additional partition for Windows formatted as ExFat. 100GBs, or above, is recommended as update to the operating system, as well as Apps requiere space on your HD or SSD [This step can be done during Mac OS X's installation process]
2- Open up BootCamp Assistant
3- Make sure only the 'Create a Windows 7 or later version install disk' is checked and your USB Flash Drive plugged in and click 'Continue'
4- Click 'Choose' and select your Windows ISO Image file
5- Select the USB Flash Drive you will be using during the installation process and click continue to confirm
6- Once done, restart your Mac and hold down the 'alt/option' key on your keyboard to bring up the Boot Menu
7- Select the USB Flash Drive named Windows, not the UEFI Boot
8- Install Windows as you normally would
* Remember to press and hold the 'alt/option' key, and select the Windows Partition, whenever the installation process requires your Mac to restart
* http://msdn.microsoft.com/en-us/library/windows/apps/jj945423.aspx
* http://windows.microsoft.com/en-us/windows-8/install-windows-on-mac

UPGRADE WINDOWS 2000 TO 2003 OR 2008 WITH EBS - 11.5.10.2 AND DB 10GR2

Hi ...
We have a new project to start upgrade windows 2000 to 2003 or 2008 (Wich it is better ) . As I woudl like to know what our options here .any reference will be more useful .
I think of cloning option . What do you think ?
Thanks in advance .
Regards,

Hi,
We have a new project to start upgrade windows 2000 to 2003 or 2008 (Wich it is better ) . As I woudl like to know what our options here .any reference will be more useful .You would need to go with Windows 2003 as Windows 2008 is not certified with 11i -- See (Oracle Applications Installation Update Notes, Release 11i (11.5.10.2) [ID 316806.1]) for details.
I think of cloning option . What do you think ?You can use Rapid Clone to clone the instance from Windows 2000 to Windows 2003 as per the following docs.
Rapid Clone Documentation Resources, Release 11i and 12 [ID 799735.1]
Or, you could just upgrade the OS directly, and in this case please make sure you follow the steps in these docs.
Note: 356878.1 - How to relink the whole Applications 11i Installation
Note: 407055.1 - Process To Upgrade the Operating System and Oracle Database Server
Thanks,
Hussein

Cannot build WINDOWS 2000

Project "EventProcessing" loaded
Project settings saved
Building "EventProcessing"
No sources to compile
Build failed
I get the above error, the toolkit just cannot find the source files. Any Windows expert around can help. I am a beginner here.
k

Ok got it corrected. thanks... my mistake.... the source file got named xyz.java.txt.
It compiles fine now
K

Cannot load Windows 7 - Satellite C660 keeps freezing

Hi Everyone.
This is a biggy. I have a Toshiba AMD Vision Satellite C660 / C660D laptop with no Windows installation disc. Last week it became very sluggish, then the interface resembled that of the safe mode interface and it finally became completely unresponsive, therefore, via F8 on start- up I selected the option which allowed for it to revert to factory settings (I no longer have this option)
The DOS screen appeared and started loading as normal then that become unresponsive so I restarted only to see Windows start up for the first time and carry on loading, prior to this I had to create a boot cd from my other laptop to reboot the system as I had lost the boot mngr.
The last part of the installation process began whereby a white Toshiba screen is displayed with a green progress bar that loads certain drivers (see attachment). There are 39 steps to this process and I seem to remember from before that the computer should keep restarting itself, but it keeps freezing after about two steps. I kept switching it off and eventually the system administrator locked my accounts.
Once again I restarted the PC but this time in safe mode The operating system did indeed load in safe mode and I created some new accounts with administrator privileges, however, I am still unable to load the whole operating system as it keeps freezing during the last part of the process.
I have very limited knowledge of loading operating systems so any help would be greatly appreciated.

Hi
First of all it was a big mistake NOT to create an Toshiba recovery disk.
The HDD recovery which you were able to start by pressing F8, is only possible if the HDD is not faulty.
I think in your case I think there is something wrong with the HDD because there was an boot mgr notification which means that notebook cannot find an boot manager in order to boot up the system.
I have no other idea as to try to reinstall the system using the Toshiba recover disk or another Windows 7 disk (of course if you own one)
If the recovery would fail, you have to investigate what hardware part might be affected. I think in such case its needed to start with HDD check.
Possibly the HDD needs to be replaced. Of course it possible that Im wrong an other part is affected but at first stage you need to check new OS installation.
A recovery disk can be ordered here:
http://backupmedia.toshiba.eu/landing.aspx

Cannot load Windows 7 - keeps freezing

Hi Everyone. This is a biggy. I have a Toshiba AMD Vision Satellite C660 / C660D laptop with no Windows installation disc. Last week it became very sluggish, then the interface resembled that of the ‘safe mode’ interface and it finally became completely unresponsive, therefore, via F8 on start- up I selected the option which allowed for it to revert to factory settings (I no longer have this option)
The DOS screen appeared and started loading as normal then that become unresponsive so I restarted only to see Windows start up for the ‘first time’ and carry on loading, prior to this I had to create a boot cd from my other laptop to reboot the system as I had lost the ‘boot mngr’.
The last part of the installation process began whereby a white Toshiba screen is displayed with a green progress bar that loads certain drivers (see attachment). There are 39 steps to this process and I seem to remember from before that the computer should keep restarting itself, but it keeps freezing after about two steps. I kept switching it off and eventually the ‘system administrator’ locked my accounts.
Once again I restarted the PC but this time in ‘safe mode’ The operating system did indeed load in safe mode and I created some new accounts with administrator privileges, however, I am still unable to load the whole operating system as it keeps freezing during the last part of the process.
I have very limited knowledge of loading operating systems so any help would be greatly appreciated.
Attachments:
crashed.gif ‏28 KB

Try holding '0' (zero) as you start the laptop to load the recovery utility and run it again.
- Peter

Cannot Load Leopard due to Historic Unresolved Problem with Tiger.....

When I installed Tiger some years ago, my computer (iMac) refused to shut down normally. I tried many times to get an answer from Apple without results. Since then I have had to shut down by holding the start button. OK. Inconvenient but it worked. Until I tried to install Leopard. Since Leopard requires a Restart and I cannot Restart from the menu I cannot install it. I left messages on Apple's Support e-mail which promises to get back in 48 hours. This was a week ago and I still have not heard from Apple Support. Any thoughts about resolving this issue?
Here is the error message that the system sends to Apple:
Unresolved kernel trap(cpu 0): 0x400 - Inst access DAR=0x0000000001266000 PC=0x0000000000000134
Latest crash info for cpu 0:
Exception state (sv=0x20BC7000)
PC=0x00000134; MSR=0x40009030; DAR=0x01266000; DSISR=0x40000000; LR=0x0089D120; R1=0x0CEC3D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x002BCD54 0x0089B918 0x002BF39C 0x002BE760 0x000A9514
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x89a000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x884000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x57d000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x526000
Proceeding back via exception chain:
Exception state (sv=0x20BC7000)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x20BDA780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.10.0: Wed May 23 16:50:59 PDT 2007; root:xnu-792.21.3~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0004): 0x400 - Inst access
Latest stack backtrace for cpu 0:
Backtrace:
0x000952D8 0x000957F0 0x00026898 0x000A8004 0x000AB980
Proceeding back via exception chain:
Exception state (sv=0x20BC7000)
PC=0x00000134; MSR=0x40009030; DAR=0x01266000; DSISR=0x40000000; LR=0x0089D120; R1=0x0CEC3D00; XCP=0x00000010 (0x400 - Inst access)
Backtrace:
0x002BCD54 0x0089B918 0x002BF39C 0x002BE760 0x000A9514
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.IOFireWireSerialBusProtocolTransport(1.4.4)@0x89a000
dependency: com.apple.iokit.IOFireWireSBP2(1.7.5)@0x884000
dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(1.4.9)@0x57d000
dependency: com.apple.iokit.IOFireWireFamily(2.2.5)@0x526000
Exception state (sv=0x20BDA780)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.10.0: Wed May 23 16:50:59 PDT 2007; root:xnu-792.21.3~1/RELEASE_PPCModel: PowerMac4,5, BootROM 4.4.5f3, 1 processors, PowerPC G4 (2.1), 800 MHz, 512 MB
Graphics: NVIDIA GeForce4 MX, GeForce4 MX, AGP, 32 MB
Memory Module: DIMM0/J22, 256 MB, SDRAM, PC133U-333
Memory Module: DIMM1/J20, 256 MB, SDRAM, PC133U-333
Modem: Dash2, UCJ, V.92, 1.0F, APPLE VERSION 2.6.6
Network Service: Built-in Ethernet, Ethernet, en0
Parallel ATA Device: Maxtor 4D080H4, 74.53 GB
Parallel ATA Device: PIONEER DVD-RW DVR-104, 7.5 GB
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: USB Receiver, Logitech, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mA
USB Device: Hub, Up to 12 Mb/sec, 500 mA
USB Device: DYMO LabelWriter 330 Turbo, DYMO, Up to 12 Mb/sec, 500 mA
FireWire Device: iPod, Apple Computer, Inc., Up to 400 Mb/sec
FireWire Device: 911D, Oxford, Up to 400 Mb/sec

DonCres wrote:
I solved the problem by reinstalling Tiger. Followed by purchasing a new iMac 20-inch, with Leopard. Am selling the older iMac.
Excellent move. The general rule is to never install any software at all on a computer that is not working properly. At best it will still be broken, at worst it will die completely
I am assuming your old Tiger was an upgrade from an earlier system and not an install on a blank HD. Usually that kind of problem requires an erase (full, not quick) and install and then a careful migration from the backup, one program at a time, in case the problem is related to an old piece of SW.

Cannot load windows 2000 (sp3) on pm8m2-v with single sata drive

Similar Messages

Maybe you are looking for