Cannot open ports on Sonicwall TZ 215
Use the wizard for a public facing server. It will create the address objects and ports you specify as well as the associated rules.
I have been battling with a new sonicwall tz 215 for 3 days now trying to simply get a port open to allow web traffic through. I have tried every tutorial, watched every youtube video, used the wizards all to no avail. I am switching out a cisco rv042 for this device. It is currently configured and works so I know that the internal machine and the ISP are allowing the proper actions to occur. When I look at the log it says Web Request Dropped. I have also used various port checkers and no matter what I can't get a single port to show open.I have restored the Sonicwall back to factory multiple times and started the process over from scratch just to make sure I don't have any rules or whatever that would prevent ports from being opened. Has anyone battled with a sonicwall device before and possibly have any other tips / suggestions? Is...
This topic first appeared in the Spiceworks Community
Similar Messages
-
Hello,
I thought I should come here as a last resort so here I go...
I have been using a WRT54G for quite some time, I find it does the job smoothly and quickly...
However, I cannot open ports (or at least a specific one)...
I am looking to host a game server on the port '43594'. I went though the router settings and "Applications and Gaming" and enabled the port...
However 'canyouseeme.org' says:
Error: I could not see your service on 58.178.203.117 on port (43594)
Reason: Connection timed out
Any leads as to why this is? It's a small Java game by the way, so not a major server. Could it actually be my modem? (which is not a linksys so I wont ask)..
Could it be my ISP? iPrimus?
Sorry if I can't explain well...
If you need more information, just tell me what your looking for.
- MorsoloTry updating your firmware then reset the defualt settings and reconfiguring it. If all fails set your PC as the DMZ if you have to. It sounds like you are doing everything you need to. I have hosted a few on-line dedicated game servers using this basic configuration.
Richard Aichner (Ikester) -
RV215W inbound rules with control ip - cannot open port 25
I have the exact same router, exact same firmware and the this exact same problem. I cannot open port 25 and specify a range of IP addresses. This is simply not working. What do we have to do to get this to work correctly? When I port forward the SMTP service it allows all IP's and works fine. When i try to use an Access Rule, it does not work. Can someone from CISCO help please? Thanks,
It's not just single port forwarding that has bugs, the entire router has bugs and simply does not work as advertised. I have found the following bugs/aspects of this router that just does not work correctly: 1. If you have to open ports, and who doesn’t, this router will eventually stop accepting packets from WAN>LAN. You will still have Internet access but no open ports. A reboot will fix this problem. Oh, by the way, this router has no scheduled reboot option! ••ßThat would be a workaround but a welcome one for this router. 2. Firewall Access rules do not work!! Yep, a Cisco router and basic functionality simply does not work. I called Cisco and even though the tech saw the router not working denied it was a bug! Said we have to do port mirroring, setup a workstation with WireShark and capture packets so we can debug the issues! I told him I would have appreciated if Cisco would have debugged the issues with their router BEFOR they shipped the units. Stay away from Cisco Small Business Routers. I wish I had. And if there are any Cisco die-hards out there willing to prove me wrong, just reply to this and please, prove me wrong that the RV series and specifically the RV215W is not JUNK.
-
Cannot open port through Airport Extreme to access security system DVR
I have internet access through Bellsouth DSL -- modem only. We had a security system set up around a DVR recording images and connected to the internet through a Linksys router. We would use a client on outside computers to connect to the security system dvr and see what was happening (live or recorded). I switched out the Linksys for the Airport Extreme, and now we cannot connect to the DVR.
Do I need to manually open a port to the DVR? How do I do this? The DVR connects to the Airport Extreme via Ethernet, and as far as I can tell, the Airport Extreme connects to the DSL modem via Ethernet using DHCP. We have a static IP address. I thank you in advance for any answers, and I apologize if I'm not giving enough information.Let's double-check your Port Mapping setup on the 802.11n AirPort Extreme Base Station (AEBSn) ...
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: 10.0.1.4
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): 6746
o Public TCP Port(s): 6746
o Private IP Address: 10.0.1.4
o Private UDP Port(s): 6746
o Private TCP Port(s): 6746
o Click "Continue" -
Telnet - cannot open port 23, connect failed
I'm having problems with Telent and Window 7. Telnet works, however on one piece of OLD legacy computer UNIX system, it fails. I experienced this same problem on Windows XP, but there was a registry fix for it. This same fix does not work on Windows 7.
The unix system does use port 23....anyone have a solution?
Below was the registry fix that fix this problem on Windows XP.
REGEDIT4
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters]
"SackOpts"=dword:00000
"Tcp1323Opts"=dword:00000Hi Milos...
(edited...added more information at the bottom). I have encluded some parameters off the unix machine.
Thanks for helping me out.
I tried PUTTY... I configured the Telnet for every possible combinations and the at didn't work either.
When you say the CurrentControlSet1 is not effective...can you please give me more details.
As I mentioned in my original POST....I had this same problem with windows xp....but the registry fix shown allowed Telnet to work. I don't know why its not working in Windows 7. I was reading that Windows 7 has Auto Windowing and I'm working if perhaps
the negoation isn't taking place. This is an old unix platform and I'll have to check to see if there is any monitoring applications...but off hand I can't think of any.
TANGO># netstat -a
Active connections (including servers)
Proto Sock# Chan# Local Address Foreign Address (state)
tcp 1 0 *.* *.*
Listening
tcp 2 1 *.* *.*
Listening
tcp 3 2 *.* *.*
Listening
tcp 4 3 *.* *.*
Listening
tcp 5 4 *.* *.*
Listening
tcp 8 47 208.246.0..telnet 33.149.0.0.2032 Bound
udp 6 55 *.talk *.* Bound
udp 7 56 *.ntalk *.* Bound
TANGO>#
TANGO># netstat -all
transmissions 0x00164bcc 1461196
mult xmit retries 0x000000be 190
sngl xmit retries 0x00000080 128
failed retries 0x00000000 0
deferrals 0x00000226 550
xmit buf err 0x00000000 0
silo underrun 0x00000000 0
late collisions 0x00000000 0
lost carrier 0x00000000 0
babble 0x00000000 0
telnet> display
will flush output when sending interrupt characters.
won't send interrupt characters in urgent mode.
won't map carriage return on output.
won't recognize certain control characters.
won't turn on socket level debugging.
won't print hexadecimal representation of network traffic.
won't show option processing.
[^E] echo.
[^]] escape.
[^H] erase.
[^C] interrupt.
[^U] kill.
[^\] quit.
[^D] eof.
telnet> -
Is anyone experimenting this kind of problems or has resolved it? Thanks. I use LabVIEW 6.1 with Windows 98.
Squish,
This forum is for CAN questions. I would strongly urge you to repost your question to the LabVIEW General category and this is a LabVIEW question.
Also, does the FTP Browser shipping example that comes with the Internet Toolkit work? If it does, then I would suggest studying that example. If it does not, then I would suggest reposting your question and giving much more detail about which VI is giving you the error and a general overview of the program.
Randy Hoskin
Applications Engineer
National Instruments
http://www.ni.com/ask -
How can I open ports on my AirPort Extreme, from WINDOWS?
I have an Airport Extreme as my router, and I have a Windows-based computer. I need to open ports on the router (ironically, it is for my Apple TV).
However, even though I can use the Airport Utility for Windows (latest version 5.5.3), I cannot open ports from the application.
Everywhere I look, I am supposed to have a firewall tab in the Advanced section, but I do not have it. The only tabs that I have in Advanced are:
Logging and Statistics
MobileMe
IPv6
How can I open ports on my Airport Extreme router from Windows?Is your AirPort Extreme the only router in your network configuration?
-
Hi All,
We have requirement of using ESB toolkit and transforming incoming xml file to edi format. So, we are using ItinerarySelectReceiveXML pipeline for receiving the input from the input location and "EDISend" pipeline for transforming it into EDI and
send it to destination.
Now, the receive pipeline is picking up the file, but it is not processed and sent to destination.
And, we are getting an Access Denied error from Dynamic send port.
Error Description :
The FILE send adapter cannot open file C:\Users\Public\Temp for writing.
Details: Access is denied.
Any Immediate solutions/suggestions are appreciated...Thanks.
AnandThe difference between dynamic and static port would be send handler. For dynamic port, default send handler will be used and for static port the one configured on the port will be used, could you validate this configuration.
Also sometimes, administrative privileges are not "real" administrative privileges and company admins will have limited permissions on C Drive folders. Try writing to some other folder to isolate the issue.
Regards, Ajeet Kumar MCTS Biztalk Server -
Cannot open socket connection on port 443
Hi!
Our server is running on Port 443.
When I try to Connect from the BlackBerry 9300, an exception is thrown "cannot open socket connection on port 443"
Can any one please help me in finding the solution to enable the port 443.
Thank you in advance!
Regards,
VinayI assume that you have verified that you can login to the ftp site using a regular ftp client (e.g. Fetch) on the Mac?
-
FTPEx: 425 Possible PASV port theft, cannot open data connection..
Hi All,
I am getting the below the error while comminicating to FTP server.
Delivery of the message to the application using connection File_http://sap.com/xi/XI/System failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: Possible PASV port theft, cannot open data connection.: com.sap.aii.adapter.file.ftp.FTPEx: 425 Possible PASV port theft, cannot open data connection..
This error is random. Some times service is working is fine and some times its failed to process.
Can any one suggest me the peramnent solution for this.
Thanks & regards,
KartikeyaHi
The reason for the error is
The ip address (+port) is not same for both these operations
- Control connection
- Data Connection
Changing active/passive mode settings might help (as a common solution).
Problem can occur due to below settings,
- FTP server/ Firewall on its side (affects Passive Mode)
- FTP client/ Firewall on its side (affects Active Mode)
After Initial Control connection is made, the below happens for Data connection
When Active, the CLIENT opens a dynamic port for DC on which it would be listening, for the server to bind its source port
When Passive, the SERVER opens a dynamic port for DC on which it would be listening for the client to bind its source port
when the firewall on Server side does not have these ports open, you get the above error.
The error could be because of other reasons also, but I suspect that the dynamic port is out range of the ports opened at your FTP server firewall.
So now I think you are one step forward to fix the issue
Regards
Vishnu -
Customer cannot open all the ports - MAP 9.5
Hi,
Taking an inventory using MAP 9.5.
Customer cannot open all the ports.
135-139 and 445 are open.
We are still not getting any success [just 3% inventory success]. Further only those machines are listed in WMI Success which are in the same subnet as the machine on which MAP is running.
We are using Inventory Scenario>Windows computers and Discovery Methods >AD + Scan IP range.
Is there any alternate method?
Thanks.Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
More Info Here...
Troubleshooting applications purchased from the App Store -
Cannot open local port whatever
Hi,
I've just downloaded AVTransmit2.java and AVReceive2.java from this website's JMF tutorial and am having a little trouble getting both classes to communicate.
I have two Command Prompt windows open and I'm trying something like
java AVTransmit2 file:C:\Whatever.au ipaddress(my machine's IP) 4000
java AVReceive2 ipaddress(my machine's IP)/4000
Whatever process I run first, the second process then tells me that it cannot open local port 4000, even though this is the port that both processes are meant to communicate on. Should I be using two different machines to communicate?
Sorry to bug everybody with this problem, it's probably been posted before but some advice would be appreciated.
ThanksErr, well, if they are both acting as servers, that's right. If you are running them on the same machine, then the first one takes port 4000 and the second one can't use it. I would think they would take 2 sets of IP and port, one for it's server port, one for it to connect to the other side...
however, I wouldn't think that the transmitter app would be using a server port. You should be starting the receiver first.
Or something else is using that port. Another receiver you started but didn't start, maybe? Some other app? It shouldn't matter what port you use. Try something else (4001, 4002, etc). -
I am encountering a strange behavior in new zones created using zonemgr 2.0.6 (this is the only way I create zones, so I do not know if the issue is more general). When I create a new zone, two strange things are happening:
1. Immediately after the zone is created, no services are running, not even ssh
2. About 10 minutes later, a whole bunch of services are running. Most of these are not running on the global zone.
For reference, nmap output on the global zone is the following:
[dcomsm1@dcomsm1:~] $ nmap t2000
Starting Nmap 5.00 ( http://nmap.org ) at 2010-02-28 20:51 EST
Interesting ports on 131.247.16.134:
Not shown: 991 closed ports
PORT STATE SERVICE
22/tcp open ssh
111/tcp open rpcbind
2161/tcp open apc-agent
3052/tcp open powerchute
4045/tcp open lockd
32774/tcp open sometimes-rpc11
32775/tcp open sometimes-rpc13
32776/tcp open sometimes-rpc15
32777/tcp open sometimes-rpc17
The new zone is created using the following zonemgr arguments:
[root@t2000:~/zonecfgs] # more ./temp.sh
#!/usr/bin/bash
./zonemgr -a add -n drenkhah -z "/export/zones" -P "root_pw" -I "131.247.16.159|e1000g0|25|drenkhah" -R "/root|/usr/bin/bash" -s "basic|lock"
zone creation output is as follows:
[root@t2000:~/zonecfgs] # ./temp.sh
Checking to see if the zone IP address (131.247.16.159) is already in use...IP is available.
cannot create '/drenkhah': leading slash in name
chmod: WARNING: can't access /export/zones/drenkhah
chown: /export/zones/drenkhah: No such file or directory
Zone drenkhah will be placed in the following directory: /export/zones/drenkhah
Preparing to install zone <drenkhah>.
Creating list of files to copy from the global zone.
Copying <2568> files to the zone.
Initializing zone product registry.
Determining zone package initialization order.
Preparing to initialize <1042> packages on the zone.
Initialized <1042> packages on zone.
Zone <drenkhah> is initialized.
The file </export/zones/drenkhah/root/var/sadm/system/logs/install_log> contains a log of the zone installation.
Creating the sysidcfg file for automated zone configuration.
Booting zone for the first time.
Waiting for first boot tasks to complete.
Waiting for automatic post-install reboot to complete
Updating netmask information.
Updating /etc/inet/hosts of the global zone with the drenkhah IP information.
Generating ssh host keys. Details in the (/root/.zonemgr/zone28330-ssh.log) file.
svcadm: Pattern 'svc:/network/ssh' doesn't match any instances
Setting the root user's home directory to /root
Setting the root user's shell to /usr/bin/bash
Disabling un-necessary services via basic method for the default services.
Zone drenkhah is complete and ready to use.
nmap output just after creating the zone is as follows:
[dcomsm1@dcomsm1:~] $ nmap drenkhah
Starting Nmap 5.00 ( http://nmap.org ) at 2010-02-28 17:53 EST
All 1000 scanned ports on 131.247.16.159 are closed
Nmap done: 1 IP address (1 host up) scanned in 29.39 seconds
nmap output 17 minutes later is as follows:
[dcomsm1@dcomsm1:~] $ nmap drenkhah
Starting Nmap 5.00 ( http://nmap.org ) at 2010-02-28 18:10 EST
Interesting ports on 131.247.16.159:
Not shown: 986 closed ports
PORT STATE SERVICE
21/tcp open ftp
22/tcp open ssh
23/tcp open telnet
25/tcp open smtp
79/tcp open finger
111/tcp open rpcbind
513/tcp open login
514/tcp open shell
587/tcp open submission
4045/tcp open lockd
6112/tcp open dtspc
6788/tcp open unknown
6789/tcp open ibm-db2-admin
7100/tcp open font-service
Nmap done: 1 IP address (1 host up) scanned in 29.25 seconds
Note that there are many open ports
# uname -a
SunOS t2000 5.10 Generic_137137-09 sun4v sparc SUNW,Sun-Fire-T200
Thanks
ManishThe Leopard OS X firewall is application based and not port based. Honestly, I haven't played with it enough to know for certain how to answer your question.
But... when you do connection sharing, you're essentially doing a port based NAT for the systems on the other side of your Mac. This pretty much keeps you from initiating anything to the other system even without a local firewall unless you were to configure port forwarding.
As for blocking packets, you would need to use the 'ipfw' command to do things at the port level. -
I have a Lorex DVR that I want to monitor from my IPhone and IPad. I used to be able to do this when I had a Belkin router (easy to open ports) but I bought the AirPort Extreme router and no longer have that capability. When I use "canyouseeme" they can NOT see 80, 9000 or 1025. Lorex says I need them all available in order to access. Help! And all the help I see refers to a earlier version of the AirPort Utility so I cant use those to look at anything, I cant find the same screens, I have version 6.1 (610.31). I also don't really understand how ports work, so I need a pretty basic explanation.
Well...I went to the modem (Westell, WireSpeed), found the NAT settings, once again, I'm WAY over my head, I am assuming this is a TCP connection (as opposed to a UDP) and per Lorex my mobile devices will use port 1025. So I gave it a "global port range" of 1-10 and I indicated that the "base host port" was 80, 1025, & 9000 (ports 1,2,3). When I selected the 'enable' it asked for a "host devise" my choices are my IPhone, IMac and the IP address for the dvr, so I choose the dvr. I still cannot connect and canyouseeme still can NOT find these open ports. This is taking up my whole day! I don't know how people figure this stuff out.
-
"Safari cannot open the page – 'too many redirects'"
Problem
iPad issue impacting our secure website clients. Error message reads “Safari cannot open the page – ‘too many redirects’”
History:
Recently, some of our secure website clients using Mac/Safari 4.0.5 faced issues, all related to one common problem that went away with Safari 5.0 & Mac OS updates. On all the three occasions, we observed that the error occurred when the HTTPS redirects contained the port number in the URL. During our discussions with Applecare personnel (case number was 350144) we understood that there have been problems with Safari 4.0.5 "not being able to handle port numbers in the URL properly". The issue went away with the launch of Safari 5 and Mac OS updates which followed the browser release.
Understandably, the resolution to the issue was fairly opaque and if I were to hazard a guess on what the problem could have been it should probably be something to do with Safari not being able to read cookies after these redirects.
Questions
1) Have any of you encountered such a problem on Mac/Safari 4.0.5 and are now facing on iPad?
2) Any workarounds / solutions / learning that you have come across and can share
Thanks!!Hi and welcome...
On a Mac. HTTPS redirects can be the result of proxies. Open System Preferences / Network. Click: Advanced tab then click: Proxies
If any of the boxes on the left under: *Select a protocol to configure* are selected, deselect, click OK.
Here's just one example of the HTTPS / Proxy issue: http://discussions.apple.com/thread.jspa?messageID=12255869�
For Safari - iPad. Tap Settings / Wi Fi / Select your network by tapping the blue arrow. Configure network settings there.
Carolyn
Message was edited by: Carolyn Samit
Maybe you are looking for
-
In F-53, the Withholding tax line item is not geting calulated
Hi All I have created a tax code for payment. while making payment through F-53, i dont see a sepreate line item getting created for for Tax(Withholding) When i double click on the vendor line item and check on the Withholding tax option box, its sho
-
Saving the content of JTable into a ascii file?
Suppose I have a JTable with certain cols and rows, is there an easy way to retrieve the table contents and save them into a ascii file on disk? Thanks for your help. helen
-
Very large files checkin to DMS/content server
Dear experts, We have DMS with content server up and running. However, there is a problem with very large files (up to 2GB!) - these files cannot be checked in due to extremely long upload times and maybe GUI limitations. Does anyone have suggestions
-
I would like to download the above programmes onto my Levono tablet which runs on Windows 8. The only information I can find is all about downloading onto iPhones and iPads. Therefore I'd like to know if anybody can help please?
-
Hi, delta load is failure and getting below errors how to resolve and where to check the IM1907693 nos. RSMO: data load error in BWP IM1907693 SXMB_moni: XML Messages error in GXP IM1907695 DB02: tablespace reached 97% i