Cannot ping the IP of the NET MGT Port
Dear all,
I configred the console port of the servers sunfire v440, v210
v240
as follow
netsc_ipaddr =172.17.0.x
netsc_ipnetmask= 255.255.255.0
netsc_ipgateway =172.17.0.1
netsc_tpelinktest="true"
netsc_dhcp="false"
I couldn't ping the IP address,
When I put a cable between the NET MGT port and the switch the light is not on in the switch and climbing in the server
H\akim
Not sure what you mean by
"climbing in the server". But
the NET-MGMT port is
10Mbit so if your switch port
is set to 100-FULL and
autonegotiation is turned
off it won't work.
Or else you have a bad cable
or switch port, which is actually
fairly common.
Similar Messages
-
VMWare Fusion - Cannot see other computers in the Workgroup
For some reason I'm unable to see or access other machines in my Windows Workgroup from within Fusion 1.1.3. Alternatively, I cannot see or access the VM from other WinXP machines in my workgroup. The other WinXP machines in my workgroup CAN at least ping the VM. I cannot ping anything outside of the VM other than OS X and my gateway/router. And yes, I've tried disabling the firewall on both the VM and other Windows machines in my Workgroupto no avail.
I am currently using a Bridged network configuration in Fusion. If I open an explorer window in the VM and type in the UNC path to OS X I can access it, but not other Windows machines on my network... why?
Perhaps someone can at least confirm whether they can access/see other computers in their Workgroup from Fusion?
Maybe this simply isn't possible under Fusion and I'm just going around in circles here...
ThanksHow did you resolve this? I am about ready to toss my month-old macbook out the window over this.
-
Trying to do pxe-boot and kickstart install on sunfire x4150 using NET MGT
I am trying to do pxe-boot and kickstart install on sunfire x4150 using NET MGT port. Is this doable? The eth0 port works fine, but the NET MGT port does not seems working. It gets the IP, gateway, mask and other info, but would not start the install. I heard that the NET MGT port is not capable of doing pxe-boot, please let me know if this is true.
Your help is appreciated.
ShengThe NET MGT port is for the ILOM. That interface is not visible to the Host OS so no it cannot be used for host communication including PXE booting...
-
Cannot ping or print from MacBook...
I'm having a really strange issue where I cannot print from my MacBook wired or wireless, I can, however, ping and print from my iMac. They are both connected to the same router/wap. I cannot ping anything from the MacBook when it is wired or wireless! All other network functions work normally though, I can access the internet and screen share over my local network... but I cannot ping to or from the MacBook.. weird eh? Can someone please shed some light on this? Thanks!
Dan OHave you tried to log in as a different user then trying from there. If you do not have a different user just create one...
Go to Sys Pref/accounts then click on the lock at the bottom left corner put in the admin password then the plus button at the bottom left of accounts window will become active, press it to create a new account.
If the ping and print work from that account then you'll know the problem is not OSX globally, at it may be fix by trashing some .plist? Not sure which ones yet.
Message was edited by: iyacyas -
Routing is OK. I can ping from Context out to local and learned subnets, but cannot ping vlan interface on the ACE or the VIP from the sup. So, this means a layer 4-7 issue.
Config is as follows:
class-map match-any VIP-A_Class
6 match virtual-address 1.1.1.3 tcp eq xxx
8 match virtual-address 1.1.1.3 tcp eq yyy
policy-map multi-match VIP-A
class VIP-A_Class
loadbalance vip inservice
loadbalance vip icmp-reply active
loadbalance vip advertise active
interface vlan 3
ip address 1.1.1.2 255.255.255.248
service-policy input VIP-A
no shutdown
Other info:
There is an operational reachable server in the group.
The Admin context does not have an interface on VLAN 3, only allocates it to the context.
I have looked into route health injection but don't think it is relevant to this, correct me if i'm wrong?
If you require more info, please let me know.yes you need it.
This is how you assign the serverfarm to the vip.
switch/User1(config)# policy-map multi-match SLB1
switch/User1(config-pmap)# class VIP-250-81
switch/User1(config-pmap-c)# no loadbalance policy SF_Linux4
switch/User1(config-pmap-c)#
gdufour-cat6k1#ping 192.168.100.250
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.100.250, timeout is 2 seconds:
Success rate is 0 percent (0/5)
gdufour-cat6k1#
[Resuming connection 1 to 127.0.0.30 ... ]
switch/User1(config-pmap-c)# loadbalance policy SF_Linux4
switch/User1(config-pmap-c)#
gdufour-cat6k1#ping 192.168.100.250
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.100.250, timeout is 2 seconds:
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
gdufour-cat6k1# -
Mail stuck in outbox-error message the connection to the server smtp.virgin
error message-'the connection to the server smtp.virgin.net on port 587 timed out'
how to i mend it!?Have taken out all server settings and put them back-no difference. Also deleted 'outbox.mbox'-no difference all answers gratefully received. Virgin do not know anything about Macssuggest I call Apple!(I went to library mail but no envelope index)?
I think I see the problem, there are at least 3 Library folder...
/Library/
/System/Library/
/Users/YourUserName/Library/
This last one is where we want to be.
but the move those folders bit?-which folders
Careful, one is a Folder, one is a File only.
Move this Folder to the Desktop...
/Users/YourUserName/Library/Caches/Mail/
Move this file to the Desktop...
/Users/YourUserName/Library/Mail/Envelope Index -
Cannot ping windows 2008 r2 while it is possible for another machine in the same network
Hi,
Recently I have set up a new server with windows 2008 r2 enterprise OS which is a domain member server.
At network layer I have two networks one with 192.168.1.0/22 and another with 10.0.0.0/24 network IDs.
My problem is that I cannot ping the newly installed server from a specific machine. Server's IP address is 192.168.1.56 and the specific machine's IP address is 10.0.0.12 and it is a windows XP machine. Of course I have to say that this problem belongs
only to this WinXP machine and all the layer 3 issues are tested and correct. This issue happens while at the same time I can ping domain controller which also is a windows 2008 r2 enterprise box and its IP address is 192.168.1.53. It turns more complicated
when I learned I can ping the winxp machine and connect to it from new server through remote desktop. Firewall also is not the obstacle because I turned it off completely.
Can anybody help me fix the problem?
TIA
BijanHi,
Check the path ping from xp machine to server its timing out after reaching 192.168.1.254 , What kind of a device is 192.168.1.254 IP belongs to.
Tracing
route to sp45newfs.ph45.local [192.168.1.56]
over
a maximum of 30 hops:
0 B15-333.PH45.LOCAL [10.0.0.12]
1 192.168.1.254
2 * * *
Computing
statistics for 50 seconds...
Source to Here This Node/Link
Hop
RTT Lost/Sent = Pct Lost/Sent = Pct Address
0 B15-333.PH45.LOCAL [10.0.0.12]
0/ 100 = 0% |
1 0ms 0/ 100 = 0% 0/ 100 = 0% (192.168.1.254)----------(Which device has this IP)
100/ 100 =100% |
2 --- (100/ 100 =100% )---(100% loss) 0/ 100 = 0% B15-333.PH45.LOCAL [0.0.0.0]
Trace
complete.
Regards,
Srivishnu.K -
I have a Mac on my home network and also a Systemline music server on same network. My PC was able to find the server but my MAC cannot. I can ping the server from the mac, but cannot actually connect . Also can't add the mac as a location from server, despite following the Systemline instructions that impy this can be done.
Can anyone please advise what I am doing wrong?Hi LowLuster
Thanks for reply. I am not an expert on these sharing protocols but I think I have turned on SMB sharing but still wont connect. I tried adding netwrik drive by using cntrl K in finder and using smb\\network address but nothing. It is driving me mad!! -
Clients cannot ping the default gateway when connected to SSID
Here is my environment,
My controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows:
LS3560CG#sh run int fa0/1
Building configuration...
Current configuration : 138 bytes
interface FastEthernet0/1
description To_WLC
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
end
The IP of management interface of WLC is 10.10.10.90, VLAN is 10, DHCP primary is 10.10.10.1 which is in the 3560, the DHCP pool is configured as blows:
LS3560CG#sh run int fa0/1
Building configuration...
Current configuration : 138 bytes
interface FastEthernet0/1
description To_WLC
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
end
The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90:
Can anyone help me with this? ThanksHi Scott
Correct! I have resolved this a few minutes earlier. I have assigned the vSwitch to Promiscuous Mode but forgot to switch it to "Accept", the default value is "Reject"
Thanks so much! -
I can SSH from the outside but cannot ping ISP gateway from 2911
Hello all,
I came across a rather strange issue. I am able to SSH to the device from my home but while I am consoled in, I cannot ping the ISP gateway or any other IP's. As expected, all trace-routes fail without hitting the gateway as the first hop. I have been reading about the NVI0 interface and I decided to use it. Most of the sample cofigs on here use the "old" ip nat inside / outside on the appropriate interfaces. What do you guys suggest?
Here is the running config. It is rather simple since i did not add all the access-lists except the ones I thought necessary to test the circuit. Please point out any mistakes or errors. Thanks in advance!
Current configuration : 1679 bytes
! Last configuration change at 04:05:17 UTC Fri Sep 12 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname StandbyGZ-2911
boot-start-marker
boot-end-marker
enable secret 5 $1$BRaM$igChPMXLeHjgYR7EGk/Nb/
no aaa new-model
no ipv6 cef
no ip source-route
ip cef
no ip domain lookup
ip domain name StandbyGZ.local
ip name-server 211.136.20.203
ip name-server 211.139.136.68
multilink bundle-name authenticated
license udi pid CISCO2911/K9 sn FGL174410H9
username StandbyGZ secret 5 $1$CXWC$m6kqTGbf0HDLCvkfU7.RA/
ip ssh version 2
interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/1
description UPLINK TO CHINA MOBILE
ip address 183.x.x.x 255.255.255.128
ip access-group REMOTE-ADMIN-ACL in
no ip redirects
ip nat enable
duplex auto
speed auto
interface GigabitEthernet0/2
description CONNECTION TO LAN SWITCH 3650-CORE
ip address 10.10.1.254 255.255.254.0
no ip redirects
ip nat enable
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat source list LAN-NAT-ACL interface GigabitEthernet0/1 overload
ip route 0.0.0.0 0.0.0.0 183.x.x.x
ip access-list standard LAN-NAT-ACL
permit 10.10.0.0 0.0.1.255
ip access-list extended REMOTE-ADMIN-ACL
permit tcp host 68.107.195.213 any eq 22 log
control-plane
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input ssh
transport output ssh
scheduler allocate 20000 1000
end
StandbyGZ-2911# sh ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 183.x.x.x YES NVRAM up up
GigabitEthernet0/2 10.10.1.254 YES NVRAM up up
NVI0 183.x.x.x YES unset up up
StandbyGZ-2911#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, + - replicated route
Gateway of last resort is 183.233.184.129 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 183.233.184.129
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.10.0.0/23 is directly connected, GigabitEthernet0/2
L 10.10.1.254/32 is directly connected, GigabitEthernet0/2
183.233.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 183.x.x.x/25 is directly connected, GigabitEthernet0/1
L 183.x.x.x/32 is directly connected, GigabitEthernet0/1Hi Chris,
That is what how I am used to configure the NAT, but IOS 12.3 and on introduced interface NVI0, which according to cisco documentation should make applying the NAT statements "easier". IP nat enable has to be enabled on all interfaces and then NVI0 makes the "inside" and "outside" decisions. I was hoping that someone could clarify the real use of that NVI0 interface and if it causes problems. Apparently it cannot be removed from the config. -
I have 3 servers : Main server, and 2 file servers in another country.
My main server can only ping the 2nd file server.
But both of our 2 file servers from another country can ping the main server.
In short, I cannot remote to the first file server.
The settings on both file servers are the same. And I don't have issues in accessing the 2nd file server using the Main server.
Can somebody have the patience to help me figure out the issue?Being able to ping the server does not mean that you remotely access it.
If you are trying to RDP a server then you need to check that RDP is enabled on the server and that traffic to port 3389 is not blocked or filtered. You can use PortQryUI for checking.
For testing, you can temporary disable security software running on the servers and try again. Also, check the filtering done on network equipment in between your servers.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile -
ACE 4700 - Cannot Ping the Alias
I cannot ping my alias addresses. I can ping the actual interface addresses but not the alias. When I look at the ARP entry on the switch it's connected to for the alias, it comes up INCOMPLETE.
Below is my config.
interface gigabitEthernet 1/1
description Fault Tolerant Port
ft-port vlan 990
no shutdown
interface gigabitEthernet 1/2
shutdown
interface gigabitEthernet 1/3
shutdown
interface gigabitEthernet 1/4
switchport trunk allowed vlan 10,112,200,254
no shutdown
resource-class RC1
limit-resource all minimum 20.00 maximum unlimited
limit-resource sticky minimum 8.00 maximum unlimited
boot system image:c4710ace-mz.A1_7b.bin
hostname atl-ace-01
access-list ALL line 8 extended permit ip any any
class-map type management match-any PING
2 match protocol icmp any
class-map type management match-all SNMP-ALLOW_CLASS
2 match protocol snmp source-address 10.150.100.202 255.255.255.255
class-map type management match-any remote_access
2 match protocol xml-https any
4 match protocol icmp any
5 match protocol telnet any
6 match protocol ssh any
7 match protocol http any
8 match protocol https any
9 match protocol snmp any
policy-map type management first-match AllowICMP
class PING
permit
policy-map type management first-match SNMP-ALLOW_POLICY
class SNMP-ALLOW_CLASS
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
interface vlan 200
ip address 10.10.200.110 255.255.254.0
alias 10.10.200.120 255.255.254.0
peer ip address 10.10.200.111 255.255.254.0
access-group input ALL
service-policy input remote_mgmt_allow_policy
service-policy input SNMP-ALLOW_POLICY
service-policy input AllowICMP
no shutdown
ft interface vlan 990
ip address 192.168.254.1 255.255.255.0
peer ip address 192.168.254.2 255.255.255.0
no shutdown
ft peer 1
heartbeat interval 250
heartbeat count 10
ft-interface vlan 990
ip route 0.0.0.0 0.0.0.0 10.10.201.254
context Exchange-CAS
allocate-interface vlan 112
allocate-interface vlan 254
member RC1
ft group 1
peer 1
priority 200
peer priority 190
associate-context Exchange-CAS
inserviceNevermind. I found an old Context on the redundant ACE with overlapping info.
-
I cannot ping any VIP from within the ACE or from rservers
I cannot ping any VIP from within the ACE or from rservers. Is this expected? I have rservers in other serverfarms that need to be able to communicate with the VIP of other serverfarms. Any help is greatly appreciated.
Thanks for you reply. here is the config. I removed other rserver and serverfarm config that does not have to do with this issue.
logging enable
logging fastpath
logging standby
logging console 4
logging timestamp
logging trap 4
logging history 4
logging buffered 4
logging persistent 4
logging monitor 4
logging device-id hostname
logging host 172.26.254.185 udp/514
logging host 172.26.221.25 udp/514
access-list INBOUND line 8 extended permit ip any any
access-list INBOUND line 16 extended permit icmp any any
access-list INBOUND line 24 extended permit tcp any any
access-list INBOUND line 32 extended permit udp any any
access-list ORADB line 8 extended permit tcp any any
probe http CITRIX
interval 30
passdetect interval 15
passdetect count 6
open 1
probe tcp HYPERION
port 19000
interval 2
faildetect 2
passdetect interval 2
passdetect count 2
receive 2
open 1
probe icmp PROBE_SERVICE_ICMP
interval 5
passdetect interval 5
probe tcp W15SPSWFET001_PROBE
interval 5
passdetect interval 5
connection term forced
open 1
parameter-map type connection TIMEOUT
set timeout inactivity 43200
parameter-map type http test
persistence-rebalance
set header-maxparse-length 2006
rserver host w0bairwatch003
description MDM-SEG
ip address 172.20.60.73
inservice
rserver host w0bairwatch004
description MDM-SEG
ip address 172.20.60.74
inservice
rserver host w0bairwatch005
description MDM-DEVICE
ip address 172.20.60.75
inservice
rserver host w0bairwatch006
description MDM-DEVICE
ip address 172.20.60.76
inservice
rserver host w0bhamobile001
description Lotus Notes Traveler Server
ip address 172.20.60.57
inservice
rserver host w0bhamobile002
description Lotus Notes Traveler Server
ip address 172.20.60.58
inservice
serverfarm host MDMDEVICE
predictor leastconns
probe PROBE_SERVICE_ICMP
rserver w0bairwatch005
inservice
rserver w0bairwatch006
serverfarm host MDMSEG
predictor leastconns
probe PROBE_SERVICE_ICMP
rserver w0bairwatch003
inservice
rserver w0bairwatch004
inservice
serverfarm host TRAVLR
predictor leastconns
probe PROBE_SERVICE_ICMP
rserver w0bhamobile001
inservice
rserver w0bhamobile002
inservice
class-map match-all MDMDEVICE-VIP
2 match virtual-address 172.20.48.35 any
class-map match-all MDMSEG-VIP
2 match virtual-address 172.20.48.33 any
class-map type management match-any REMOTE_ACCESS
description Remote access traffic match
201 match protocol ssh any
202 match protocol telnet any
203 match protocol icmp any
204 match protocol https any
205 match protocol http any
206 match protocol xml-https any
207 match protocol snmp any
class-map match-all TRAVLR-VIP
2 match virtual-address 172.20.48.34 any
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_ACCESS
permit
policy-map type loadbalance first-match MDMDEVICE
class class-default
serverfarm MDMDEVICE
policy-map type loadbalance first-match MDMSEG
class class-default
serverfarm MDMSEG
policy-map type loadbalance first-match TRAVLR
class class-default
serverfarm TRAVLR
policy-map multi-match CLIENTS-VIPS
class MDMDEVICE-VIP
loadbalance vip inservice
loadbalance policy MDMDEVICE
loadbalance vip icmp-reply active
class MDMSEG-VIP
loadbalance vip inservice
loadbalance policy MDMSEG
loadbalance vip icmp-reply active
class TRAVLR-VIP
loadbalance vip inservice
loadbalance policy TRAVLR
loadbalance vip icmp-reply active
interface vlan 48
ip address 172.20.48.10 255.255.255.0
access-group input INBOUND
access-group output INBOUND
service-policy input REMOTE_MGMT_ALLOW_POLICY
service-policy input CLIENTS-VIPS
no shutdown
interface vlan 60
ip address 172.20.60.10 255.255.255.0
access-group input INBOUND
access-group output INBOUND
service-policy input REMOTE_MGMT_ALLOW_POLICY
no shutdown
ip route 0.0.0.0 0.0.0.0 172.20.48.1 -
Cannot ping Real IP, but can ping Virtual IP, what is the issue?
Hi
I have load balancing for some servers on CSM, i can ping to VIP but cannot ping to Real IP of servers behind CSM. I need it for some testing and management pupose, Can anyone help to spot the issue? thanx
Topology
MSFC--FWSM--CSM--serversin routed mode, by default, the CSM does not allow client to connect directly to the servers.
To allow this traffic you need to create a vserver for the subnet with a predictor forward serverfarm
ie:
serverfarm route
no nat server
predictor forward
vserver vlanX
vip x.x.x.0 /24 any
serverfarm route
inservice
Gilles. -
Hi
Network:
One firewall where the IP address is the gateway for all the internal computers and server
From one if the internal computers I can ping the the gateway
From the server I can ping all the internal computers but I cannot ping the gateway
On the server I can ping:
- 127.0.0.1,
- the IP address on the server
- All the internal computers
A hint would be nice
Best Regards
John BArp -a
Interface: 10.0.0.2 on Interface 0x1000003
Internet Address Physical Address Type
10.0.0.1 10-7b-ef-3a-58-09 dynamic
10.0.0.26 00-01-e6-b4-e1-fe dynamic
Ipconfig /all
Windows 2000 IP Configuration
Host Name . . . . . . . . . . . . : krogh01
Primary DNS Suffix . . . . . . . : Krogh.local
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : Krogh.local
Ethernet adapter Inside:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP NC7760 Gigabit Server Adapter
Physical Address. . . . . . . . . : 00-0B-CD-1C-7C-D9
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.0.0.2
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.0.0.1
DNS Servers . . . . . . . . . . . : 10.0.0.2
212.242.40.3
212.242.40.51
Ping 10.0.0.1
Pinging 10.0.0.1 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 10.0.0.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Ping 10.0.0.26
Pinging 10.0.0.26 with 32 bytes of data:
Reply from 10.0.0.26: bytes=32 time=1ms TTL=64
Reply from 10.0.0.26: bytes=32 time<10ms TTL=64
Reply from 10.0.0.26: bytes=32 time<10ms TTL=64
Reply from 10.0.0.26: bytes=32 time<10ms TTL=64
Ping statistics for 10.0.0.26:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 1ms, Average = 0ms
I can ping every computer on internal network without any problems, it is only the gateway I have problem with.
I have now made a ping session from a computer on the internal network:
Microsoft Windows [version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. Alle rettigheder forbeholdes.
C:\Users\lh>ipconfig /all
Windows IP-konfiguration
Værtsnavn. . . . . . . . . . . . . . . . . . : NUC-lone
Primært DNS-suffiks. . . . . . . . . . . . . : Krogh.local
Nodetype . . . . . . . . . . . . . . . . . . : Hybrid
IP-routing aktiveret . . . . . . . . . . . . : Nej
WINS-proxy aktiveret . . . . . . . . . . . . : Nej
Søgeliste for DNS-suffiks. . . . . . . . . . : Krogh.local
Ethernet-netværkskort LAN-forbindelse:
Forbindelsesspecifikt DNS-suffiks. . . . . . :
Beskrivelse. . . . . . . . . . . . . . . . . : Intel(R) Ethernet Connection I
218-V
Fysisk adresse . . . . . . . . . . . . . . . : C0-3F-D5-61-7A-3A
DHCP aktiveret . . . . . . . . . . . . . . . : Ja
Automatisk konfiguration aktiveret . . . . . : Ja
Link-local-IPv6-adresse . . . . . : fe80::5c7a:dcbe:f8:7de7%11(Foretrukken)
IPv4-adresse . . . . . . . . . . . . . . . . : 10.0.0.113(Foretrukken)
Undernetmaske. . . . . . . . . . . . . . . . : 255.255.255.0
Rettigheden opnået . . . . . . . . . . . . . : 12. december 2014 03:15:59
Rettigheden udløber. . . . . . . . . . . . . : 19. december 2014 08:05:30
Standardgateway. . . . . . . . . . . . . . . : 10.0.0.1
DHCP-server. . . . . . . . . . . . . . . . . : 10.0.0.1
DHCPv6 IAID . . . . . . . . . . . : 247480277
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1B-40-6D-C9-C0-3F-D5-61-7A-3A
DNS-servere. . . . . . . . . . . . . . . . . : 10.0.0.2
212.242.40.3
212.242.40.51
NetBIOS over Tcpip . . . . . . . . . . . . . : Aktiveret
Tunnel-netværkskort isatap.{B46FAFD6-A60A-48D9-967D-4081FAE7F6AE}:
Medietilstand. . . . . . . . . . . . . . . . : Mediet afbrudt
Forbindelsesspecifikt DNS-suffiks. . . . . . :
Beskrivelse. . . . . . . . . . . . . . . . . : Microsoft ISATAP-netværkskort
Fysisk adresse . . . . . . . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP aktiveret . . . . . . . . . . . . . . . : Nej
Automatisk konfiguration aktiveret . . . . . : Ja
Tunnel-netværkskort Teredo Tunneling Pseudo-Interface:
Medietilstand. . . . . . . . . . . . . . . . : Mediet afbrudt
Forbindelsesspecifikt DNS-suffiks. . . . . . :
Beskrivelse. . . . . . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interf
ace
Fysisk adresse . . . . . . . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP aktiveret . . . . . . . . . . . . . . . : Nej
Automatisk konfiguration aktiveret . . . . . : Ja
C:\Users\lh>ping 10.0.0.1
Pinger 10.0.0.1 med 32 byte data:
Svar fra 10.0.0.1: byte=32 tid=1ms TTL=64
Svar fra 10.0.0.1: byte=32 tid=1ms TTL=64
Svar fra 10.0.0.1: byte=32 tid=1ms TTL=64
Svar fra 10.0.0.1: byte=32 tid=1ms TTL=64
Ping-statistikker for 10.0.0.1:
Pakker: Sendt = 4, modtaget = 4, tabt = 0 (0% tab),
Beregnet tid for rundtur i millisekunder:
Minimum = 1ms, Maksimum = 1ms, Gennemsnitlig = 1ms
C:\Users\lh>
A hint would be nice :-)
Best Regards
John B
Maybe you are looking for
-
Can't play newly copied music in iOS 8 Music app when "Repeat Album" is on
Apologies in advance for inability to accurately describe what's going on, so I took a video of the weird behavior as well: YouTube video of iOS 8 / iTunes 12 music syncing issue I am trying to sync my music on my iPhone 6 running iOS 8.1.2 with iTun
-
Did not get Acrobat 9 with my CS5 Design premium download ???
I have the license key sent by my company for CS5 Design Premium. We upgraded from a previous version of CS3 and I was issued a new laptop to install the upgrade. - I no longer have the computer with the CS3 version or a disk from the past. This is a
-
File to File scenario, file content conversion
HI there, I am facing this scenario, flat file -> XI -> flat file. Files are fixed length ones and .txt. the structure of the incoming file is something like: field1field2field3field4 field1field2field3field4field5 That means that there is no separat
-
Scrolling in Photo Events List for iPod Syncing
I'd like to know if this is a iTunes-wide bug or simply something on my computer. When on the Photos pane for iPod Touch syncing, there is a box for Events. Scrolling this list of Events on my touchpad only works horizontally, not up/down, though the
-
Making text glow with a spinning logo in menu
hi all maybe hal could help me, i am wanting to create some menu pages ,where i have a spinning logo and text that glows when selected,not sure how to do it,i nearly can understand about creating menu pages in photoshop using layersfor the glow ,but