Cannot print from Canon MF4412 through USB port of Time Capsule

Hi everyone,
I've recently purchased a new Canon imageCLASS MF4412 and cannot print while connected to the USB port of the time capsule. I can print and scan perfectly when connected directly to the mac.
This is the exact steps I took:
1.After connecting the usb cable to the back of Time capsule, I go to the sys pref pane to add a printer.
2.It shows up as a 'Bonjour' and I had to manually select the driver.
3.It added fine and I thought everything was setup.
4.However, when i go to print something, there's an error. "Canon URF II Printer Driver"
"Cannon communicate with the printer, or the printer is not supported. If the printer is supported, check the printer connection and add it again. Then, if the Print Dialog box has a [Printer Info] button, acquire the printer information: 10322"
Anybody know of a solution?
Thanks.

I got a similar problem on MF4412, the canon 4412 is connected the newest airport extreme , it get configured. But I got same problem described about on my leopard, lion, even worst on iOS, it does not find the printer. But I got a Windows 7 starter NetBook ...haha it works, I can print it from Windows. what is the problem then,it works on Windows but not Apple's OS??????

Similar Messages

How do I connect a Canon Selphy CP900 using the USB port on Time Capsule

I am running a MacBook Pro with Mountain Lion (10.8.5) and have installed the CP 900 driver (6.2) supplied by Canon from their website. I have a Time Capsule set up as a stand alone internal network at my home and use it as a network attched hard drive directly - not via Time Machine. I can "see" the printer when I connect but cannot print to it. I open a photo in preview and select the printer and print.
I get a
Cannin Selphy CP Generic
connection method not supported message - 9786
The printer does show up in my Print and Scan control panel in System Preferences
I also cannot reach it to check suplies
At the print it dsiplays the printer to computer connection via USB
Any help would be appreciated.
Thanks, Asa

Hi Asa,
I experienced the same error -9786 although I'm not using the time capsule, but only through the wifi.
I did following and resolved the problem.
1. I re-installed the driver software.
2. I re-configured the printer settings. (System Preferences - Printers and Scanners - "+" button)
3. I didn't add the selphy manually, but just I just input "CP" in the searchbox in "Add" dialog, and clicked "OK" button then the printer is set automatically.
4. I tried pringing a photo from iPhoto and could print correctly.
it looks like the key action is #2 and #3 above, so why don't you give a try?

Wireless printing from windows XP on HP1025 connected to time capsule

I have a new BUSINESS DEL laptop that I want to print from on my HOME Apple network.
My printer, HP1025nw, is directly network connected to the time capsule. Printing from iMac and MacBook is working OK, however I can not seems to get the DELL ( running XP ) to print.
Network setup on the DELL is OK, I'm connected wireless, can access internet, etc... no prolem there.
Any suggestions?

Load bonjour for windows..
Apple network resources are hidden from the PC.. without bonjour.. once you load that it should help.
If you still have issues.. how is the printer connected.. USB is the big issue one.
But if the printer is simply plugged into ethernet or wireless connected then the apple network is irrelevant. Just follow the HP instructions for installation of network printers.

Moved drive to USB Port on Time Capsule and TM no longer sees backups

I moved my FireWire attached HD from a direct attachment to my Mac Pro to attached via the USB port on my Time Capsule. Time Machine now wants to start over, and does not see the previous backups.
The destination drive name did not change, other than the added NAS address.
Is there a way to force TM to use the previous backup set incrementally instead of starting over?
Thx

SRJaynes wrote:
I moved my FireWire attached HD from a direct attachment to my Mac Pro to attached via the USB port on my Time Capsule.
unfortunately, it's not that simple. TM treats backups to directly attached drives differently vs. networked ones.
see this for more information and possible solutions: http://web.me.com/pondini/Time_Machine/18.html
JGG

Macbook won't read card from Canon G10 in USB port

I can't copy Canon G10 RAW files from an SD card via a USB card reader onto an aluminum MacBook. I tried using Adobe Lightroom (the way I usually do this on another machine) to import the files but it couldn't recognize them. I tried to copy the files into a folder on the Desktop but I got a insufficient priveleges message. It seemed to copy the file names but tnot the files. When I tried to remove the card I got a "File is in use and can't be removed" message.
The card reader and the card work fine on a 24"Intel iMac.
Another USB card works fine in the card reader on the MacBook, too.
I'm puzzled.

Some added info, i CAN boot the bricked machine into Safe mode, but at reboot I get stuck in the same cycle again.
Oh, and in SafeBoot, the Macbook still tells me that no Airport card is installed, even though I know it does (and it's not knocked loose or anything).....

Cannot print from Canon iRC2380i network printer, Help??

I am trying to connect to our office network printer.
When I search for the printer my Macbook Pro can find it and when I key in the IP address it connects successfully and chooses the Generic PostScript Printer as the driver.
However when I try and print it just prints a page with one line of random encrypted text and then many blank pages.
I'm not sure how to fix this.
Running OS X 10.6.8
Please help!

Check firewalls
The box said windows xp or better... So I installed Linux!

Cannot get my iMac OSX 10.5.2 to print on canon mf4412

Hi All,
I cannot get my iMac OSX 10.5.2 to connect and print on canon mf4412. I installed UFRII_V224_MacOSX_uk_EN driver but to no avail. iMac doesn't recongnize the printer and throws client connect error. I tried the printer on Win XP & works fine.
Can somebody please help me resolve this issue?
Thanks!

I'm having the exact same problem. Have downloaded the drivers from both the singapore and uk websites of canon and yet it doesnt print.

I have an iMac and also a MacBook. All of a sudden my iMac does not recognise my Canon 500D camera even though I have downloaded 1000s of photographs from it via the USB port. The MacBook recognises the camera immediately. Can anyone help?

I have an iMac and also a MacBook. All of a sudden my iMac does not recognise my Canon 500D camera even though I have downloaded 1000s of photographs from it via the USB port. The MacBook recognises the camera immediately. Can anyone help?

Thank you for your reply. I know I can use a card reader however I don't see why I should when importing directly from my camera has worked reliably for years. The process I use is simply connecting the digital output from my camera to the USB port on the iMac, which has previously automatically opened iPhoto ready for the import. Now all of a sudden my iMac does not recognise the camera. However if I connect in the same way to my MacBook then iPhoto opens automatically on the MacBook, recognises the camera and is ready for importing. So whilst I know I can use a reader, or my MacBook I want to use my iMac in the same way that I have for years. I can only assume that the settings on the iMac may have changed, but I cannot verify this.

Printer connected to Airport Express USB port won't come online after firmware 7.6 upgrade. I've tried backing up to 7.5.2, but it still shows offline. It is a Canon iP4600 printer and I'm running OS 10.6.8. I've powered everything down and still no go.

Printer connected to Airport Express USB port won't come online after firmware 7.6 upgrade. I've tried backing up to 7.5.2, but it still shows offline. It is a Canon iP4600 printer and I'm running OS 10.6.8. I've powered everything down and still no go. I've connected the printer directly to my MacBook's USB port and it works fine. Any suggestions?

I have an iP4500, which I assume is quite similar to your model.
I had to reset the printing system to get things printing again. Only takes a few minutes and no problems at all since I did it a week ago or so.
Plug the printer into the USB port on the Express and restart the printer.
Open System Preferences (gear icon on the dock) and then open Print and Fax
Right-Click in the printer area on the left and select Reset Printing System
Then click the + (plus) button at the bottom of the printer list to install the printer again.

Is it possible to print from iphone 5 through time capsule on wi-fi, usb connected to printer (no AirPrint support)?

Is it possible to print from iphone 5 through time capsule on wi-fi, that is usb connected to printer (no AirPrint support)?
I can print on the same printer on my Macs...was wondering if I could do the same with iOS devices?

Try Printopia. There is a free trial, so it will cost you nothing to find out if it works.
Printopia - AirPrint to Any Printer - Print from iPad - Print from iPhone ...

Cannot print from my ipad to canon air printer

Cannot print from my ipad 2

Thanks to searching the community I have got a result. Power off and reboot (press front home button together with top right button) = air print is now recognising my Canon air printer. This reboot is useful for clearing similar types of problems.

Cannot print from hp DeskJet F4580

I have just bought my first MacBook with Mac OS X 10.6.4. Great computer.
However I cannot print from the wireless hp printer. I downloaded the latest driver from hp (maybe a fault) and started to install. Everything went as expected untill the setup process of the Printer Queue. Here I add the printer in order to create the Printer Queue, but when I click on the continue buttom I get this warning: Are you sure you want to continue without adding a Print Queue? I finished the installation with a congratulation sign.
Therefore there is no doubt, that the printer queue is missing. However I cannot found out to install the printer queue.
The printer is a socalled all-in-one printer. The scanner function is perfect with the wireless connection. But not the printer function.
I have also tried to connect via usb cabel. The result is the same. Scanner okay. Printer not okay.
The printer works perfect under Windows.
I hope somebody can help me. Thanks in advance.
Erik

I'm having the same problem ! The wireless printing works using OS 10.5 on a G4 PowerBook but not OS 10.6 on an intel MacBook. I'm going to get in touch with HP as have used the latest drivers (as you have) - I've re-installed the HP software using Software Update for the latest version - still can't print. USB printing is also faulty so must be their drivers.
I'll let you know if I have any luck !
Simon

How can i use labview for communicating with pic18 microcontroller through usb port?

Hi all,
I want to make a DAQ card using pic 18 microcontroller which has a built-in usb protocol. I have the firmware of this
controller which will make it as a usb device. How can i receive the analog voltages from this DAQ card in Labview? or i mean to say that how i can communicate labview with the Pic 18 microcontroller through usb port? I have also the
mpusbapi.dll file which is for Visual C++. Can i make changes in this dll file to make it compatible with labview?

Which labview version do you have. Up to labview 7.1 it was no USB raw communication options. I have heard it did not work well in 7.1, but from 8.x most of the errors were fixed.
Here is a link it should be useful http://forums.ni.com/ni/board/message?board.id=170&message.id=340676&query.id=365864#M340676
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

Photoshop suddenly does not print to Epson 3880 - PROBLEM: Cannot print from Photoshop After restart error message appears: - "There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopen

PROBLEM: Cannot print from Photoshop
After restart error message appears:
— “There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopened any documents.”
• All print commands are greyed out and unavailable — even to call up the printer commands cannot be done.
The printer printed fine until about 2 weeks ago when this error message appeared. Printing continues from Pages, I-photo, preview etc. — only Photoshop fails.
The printer has been turned on and off, as have open documents been closed and open etc.. Preferences reset. Repeatedly I have read through blogs and forums and attempted to contact Adobe — all without results
Epson support struggled to find reason and several solutions were tried and they assume this is an Adobe problem.
Running Mac Powerbook X 10.10.2 / Photoshop CS6 13.0.6.x64
Attempting unsuccessfully to print to Epson 3880
What Adobe support will be of help.
Robert Darling — 2/19, 20, 21,22,23/2015

Probably best to ask in Photoshop General Discussion
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

I cannot print from firefox. I can print from open office. It seems to have something to do with when frames open because in IE, I can print a whole page, but when I try to use a print button embeded in a page or frame it does not work.

Cannot print from firefox at all.
In Internet Explorer, I was able to print by pushing the print button, but when opening a frame, like in mapquest, the embedded print button brings up an options window that has print frames options in it, but when hit OK in this box, a second error box comes up with a yellow exclamation point and nothing prints. I have a feeling that it is the same problem with both browsers, but would prefer using firefox. Can you help with this?

Yes, I tried that.   The files were ordered by their original numbers as imported from the camera, but I batched them through Phocoshop to downsize all of them into a more manageable file size.   I opened that destination folder from quick time from where it said select image sequence.   I clicked on the first one and opened it.   The result was a large image with an arrow indicating a movie was ready to go.   When I pressed the arrow, though, I realized it had only imported that one frame so there was no movie.   The files are Jpgs and are about 450 KB each.
    To your knowledge are there any links to iMovie tutorials or quick time tutorials that may address this situation? Maybe there will be one I haven't looked at yet.
    Thanks

Cannot print from Canon MF4412 through USB port of Time Capsule

Similar Messages

Maybe you are looking for