Cannot put unique info in title block in hierarchical design
To identify the differences between subcircuits in a hierarchical design (such as channel number!!) I tried to use a title block. No matter what is placed on the schematic page, all blocks get the same data. The only exception appears to be the "renumber" function that allows you to "lock" the REFDES. That function is poor too, because to get REFDES numbers that are in a configuration compatible with the subcircuits, they have to be entered, one at a time, by hand --- painful.
To identify the differences between subcircuits in a hierarchical design (such as channel number!!) I tried to use a title block. No matter what is placed on the schematic page, all blocks get the same data. The only exception appears to be the "renumber" function that allows you to "lock" the REFDES. That function is poor too, because to get REFDES numbers that are in a configuration compatible with the subcircuits, they have to be entered, one at a time, by hand --- painful.
Similar Messages
-
HT1918 cannot update payment info system is blocking it
cannot update payment info system is blocking it
I think that the expiry date will be shown as asterisks, and I don't think that the security code will be re-displayed either (similarly only part of the actual card number is displayed) - just in case somebody gets access to your iTunes account then they can't see your card details. If you aren't getting any error messages when you've entered them then that implies that iTunes has accepted them as being valid.
-
I have an I pad 2 . I have put things for sale on Craigslist but I cannot put pictures on the ad. Is there an app or something I need to be able to load the pictures to the ad. I also have an I phone4s same thing with it. Appreciate any info. Thanks iPad
Yes there is; http://itunes.apple.com/app/+craigslist+/id373576667?alreadyRedirected=1&mt=8
-
I have an I pad 2 . I have put things for sale on Craigslist but I cannot put pictures on the ad. Is there an app or so etching I need to be able to load the pictures to the ad. I also have an I phone4s same thing with it. Appreciate any info. Thanks
There are Craigslist apps that are nice, but trying using copy paste. Go to your photos, select the photo. Hold down your finger on it to copy. Then in the body of the post, hold down your finger and select paste.
-
Error: 1012704 Dynamic Calc processor cannot lock more than [25] ESM blocks
Dear All,
I get the Following Error in the Essbase console when I try to Execute any CalcScript.
Error: 1012704 Dynamic Calc processor cannot lock more than [25] ESM blocks during the calculation, please increase CalcLockBlock setting and then retry(a small data cache setting could also cause this problem, please check the data cache size setting)_+
Please find the detailed output of the Statics of my Planning Applications Database and outline.
please help guys........
GetDbStats:
-------Statistics of AWRGPLAN:Plan1 -------
Dimension Name Type Declared Size Actual Size
===================================================================
HSP_Rates SPARSE 11 11
Account DENSE 602 420
Period DENSE 19 19
Year SPARSE 31 31
Scenario SPARSE 6 6
Version SPARSE 4 4
Currency SPARSE 10 10
Entity SPARSE 28 18
Departments SPARSE 165 119
ICP SPARSE 80 74
LoB SPARSE 396 344
Locations SPARSE 57 35
View SPARSE 5 5
Number of dimensions : 13
Declared Block Size : 11438
Actual Block Size : 7980
Declared Maximum Blocks : 3.41379650304E+015
Actual Maximum Blocks : 1.87262635317E+015
Number of Non Missing Leaf Blocks : 10664
Number of Non Missing Non Leaf Blocks : 2326
Number of Total Blocks : 12990
Index Type : B+ TREE
Average Block Density : 0.01503759
Average Sparse Density : 6.936782E-010
Block Compression Ratio : 0.001449493
Average Clustering Ratio : 0.3333527
Average Fragmentation Quotient : 19.3336
Free Space Recovery is Needed : No
Estimated Bytes of Recoverable Free Space : 0
GetDbInfo:
----- Database Information -----
Name : Plan1
Application Name : AWRGPLAN
Database Type : NORMAL
Status : Loaded
Elapsed Db Time : 00:00:05:00
Users Connected : 2
Blocks Locked : 0
Dimensions : 13
Data Status : Data has been modified
since last calculation.
Data File Cache Size Setting : 0
Current Data File Cache Size : 0
Data Cache Size Setting : 3128160
Current Data Cache Size : 3128160
Index Cache Size Setting : 1048576
Current Index Cache Size : 1048576
Index Page Size Setting : 8192
Current Index Page Size : 8192
Cache Memory Locking : Disabled
Database State : Read-write
Data Compression on Disk : Yes
Data Compression Type : BitMap Compression
Retrieval Buffer Size (in K) : 10
Retrieval Sort Buffer Size (in K) : 10
Isolation Level : Uncommitted Access
Pre Image Access : No
Time Out : Never
Number of blocks modified before internal commit : 3000
Number of rows to data load before internal commit : 0
Number of disk volume definitions : 0
Currency Info
Currency Country Dimension Member : Entity
Currency Time Dimension Member : Period
Currency Category Dimension Member : Account
Currency Type Dimension Member :
Currency Partition Member :
Request Info
Request Type : Data Load
User Name : admin@Native Directory
Start Time : Mon Aug 15 18:35:51 2011
End Time : Mon Aug 15 18:35:51 2011
Request Type : Customized Calculation
User Name : 6236@Native Directory
Start Time : Tue Aug 16 09:44:10 2011
End Time : Tue Aug 16 09:44:12 2011
Request Type : Outline Update
User Name : admin@Native Directory
Start Time : Tue Aug 16 10:50:02 2011
End Time : Tue Aug 16 10:50:02 2011
ListFiles:
File Type
Valid Choices: 1) Index 2) Data 3) Index|Data
>>Currently>> 3) Index|Data
Application Name: AWRGPLAN
Database Name: Plan1
----- Index File Information -----
Index File Count: 1
File 1:
File Name: C:\Oracle\Middleware\user_projects\epmsystem1\EssbaseServer\essbaseserver1\APP\AWRGPLAN\Plan1\ess00001.ind
File Type: INDEX
File Number: 1 of 1
File Size: 8,024 KB (8,216,576 bytes)
File Opened: Y
Index File Size Total: 8,024 KB (8,216,576 bytes)
----- Data File Information -----
Data File Count: 1
File 1:
File Name: C:\Oracle\Middleware\user_projects\epmsystem1\EssbaseServer\essbaseserver1\APP\AWRGPLAN\Plan1\ess00001.pag
File Type: DATA
File Number: 1 of 1
File Size: 1,397 KB (1,430,086 bytes)
File Opened: Y
Data File Size Total: 1,397 KB (1,430,086 bytes)
File Size Grand Total: 9,421 KB (9,646,662 bytes)
GetAppInfo:
-------Application Info-------
Name : AWRGPLAN
Server Name : GITSHYPT01:1423
App type : Non-unicode mode
Application Locale : English_UnitedStates.Latin1@Binary
Status : Loaded
Elapsed App Time : 00:00:05:24
Users Connected : 2
Data Storage Type : Multidimensional Data Storage
Number of DBs : 3
List of Databases
Database (0) : Plan1
Database (1) : Plan2
Database (2) : Plan3ESM Block Issue
Cheers..!! -
I have several MP3 files that I cannot edit the info for. I just noticed/incurred this issue after upgrading to iTunes 9.0.0.70. After the iTunes 9.0.1.8 upgrade, I am still having the issue.
When I try to click into a field, the cursor does not appear. When I right-click and choose "Get Info," everything is grayed out.
This happens to MP3 files downloaded from the internet, MP3 files that I create/record myself on my PC, and also MP3 files ripped from CD. It does not happen with every MP3, though. Also, it can happen with some MP3 files from the same source as others that I can edit.
One note is that I can find the file via Windows Explorer and physically edit the properties of the MP3 files using the "Advanced" properties. As soon as I change the title, author, album, etc. and play the song in iTunes, all of the correct/adjusted fields show.
Another note that I have noticed on one particular pair of editable/non-editable MP3 files from the same source is that one is recognized as ID3 Tag v2.2 and one is ID3 Tag v2.3.
Is this a known iTunes 9.0 bug or is there a fix for this issue?OK...Here's something to complicate the matter for you:
I just went through some of my older MP3 files, some that I have customized the info on, and all of the info was grayed out and uneditable. I went through a few in a row and found one that I could edit. I closed the window and tried to edit the MP3s again. This time, I found that I could edit all of the ones I could not edit (just 5 seconds earlier) but could not edit the one I previously could edit. After closing the windows and trying a third time, I could edit all of the MP3 files in the list.
What is up? Apple, are you aware of this issue? -
Cannot find Battery Info in System Profiler
Cannot find "Battery Info" in System Profiler (4.0.4).
Originally, I was going to title this post "battery not charging" - which is why I am looking for battery details. Of course, as soon as I started typing the battery clicked up a notch (29% to 30%).
So, I got a confused battery and a confused System Profiler.
A couple of weeks ago I had drained the battery completely and had to even run off the backup battery as I quickly finished what I was doing. I had since fully charged the battery and thought there were no problems.
Then suddenly a couple of days ago, I looked up and it was stuck at 33%. When I tried to switch from "Percentage" to "Time", all I got was a "Calculating...", which it never actually did. I tried unplugging the computer, and it indeed did run off battery power, so it was at least communicating power-wise, if not information-wise. Two days of fiddling around offered no solutions. (Zapped the PRAM, reset PMU). Meanwhile the battery kept on not charging.
Then, I start typing here and suddenly the battery is communicating with the computer. Percentage is ticking up and there is even an estimated "time until full". However, System Profiler still does not see any battery, or in fact even give me anything to click on for power management. It's not under Hardware, Software, Network or Logs. "Extended Report" doesn't find it either. I'm hoping I am just missing it somehow... is "Battery Information" hidden somewhere?
The battery plug has now switched from green to orange and the indicator icon from a battery with a plug, to a battery with a lightning bolt. While I was trying to figure out the problem, I have taken out the battery several times, so I doubt it would be a simple connection issue.
While I would like to believe my computer has magically healed itself, I suspect that something is still amiss. Maybe earlier versions of System Profiler did not have Battery Info?Hi, RW, and welcome to Apple Discussions. System Profiler prior to the version that came with Tiger doesn't report any battery info. If you're running Panther, that's why you can't find anything about your battery in SP. Jeremy Kezer's XBattery will provide info about your battery in Panther.
Test to see whether your battery charges with a different, known-good AC adapter. That's the cheapest component of the charging system to replace if yours is faulty, and with luck that will prove to be where the problem lies. Other possibilities are a bad battery, DC-In board, or logic board. -
ERROR ORA-01452: cannot CREATE UNIQUE INDEX; duplicate keys found
Hi,
SAPSSRC.log
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: START OF LOG: 20071018195059
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#12 $ SAP
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: version R6.40/V1.4
Compiled Nov 30 2005 20:41:21
C:\usr\sap\BW1\SYS\exe\run/R3load.exe -ctf I C:/temp/51030721/EXP2/DATA/SAPSSRC.STR C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/DDLORA.TPL C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.TSK ORA -l C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.log
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: job completed
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: END OF LOG: 20071018195059
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: START OF LOG: 20071018195133
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#12 $ SAP
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: version R6.40/V1.4
Compiled Nov 30 2005 20:41:21
C:\usr\sap\BW1\SYS\exe\run/R3load.exe -dbcodepage 4103 -i C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.cmd -l C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.log -stop_on_error
DbSl Trace: ORA-1403 when accessing table SAPUSER
(DB) INFO: connected to DB
(DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): WE8DEC
(DB) INFO: ABTREE created #20071018195134
(IMP) INFO: import of ABTREE completed (39 rows) #20071018195134
(DB) INFO: ABTREE~0 created #20071018195134
(DB) INFO: AKB_CHKCONF created #20071018195134
(IMP) INFO: import of AKB_CHKCONF completed (0 rows) #20071018195134
(DB) INFO: AKB_CHKCONF~0 created #20071018195134
(DB) INFO: AKB_INDX created #20071018195134
(IMP) INFO: import of AKB_INDX completed (0 rows) #20071018195134
(DB) INFO: AKB_INDX~0 created #20071018195134
(DB) INFO: AKB_USAGE_INFO created #20071018195134
(IMP) INFO: import of AKB_USAGE_INFO completed (0 rows) #20071018195134
(DB) INFO: AKB_USAGE_INFO~0 created #20071018195134
(DB) INFO: AKB_USAGE_INFO2 created #20071018195134
(IMP) INFO: import of AKB_USAGE_INFO2 completed (0 rows) #20071018195134
(DB) INFO: AKB_USAGE_INFO2~0 created #20071018195134
(DB) INFO: APTREE created #20071018195134
(IMP) INFO: import of APTREE completed (388 rows) #20071018195134
(DB) INFO: APTREE~0 created #20071018195134
(DB) INFO: APTREE~001 created #20071018195134
(DB) INFO: APTREET created #20071018195134
(IMP) INFO: import of APTREET completed (272 rows) #20071018195134
DbSl Trace: Error in exec_immediate()
DbSl Trace: ORA-1452 occurred when executing SQL statement (parse error offset=35)
(DB) ERROR: DDL statement failed
(CREATE UNIQUE INDEX "APTREET~0" ON "APTREET" ( "SPRAS", "ID", "NAME" ) TABLESPACE PSAPBW1 STORAGE (INITIAL 44981 NEXT 0000000040K MINEXTENTS 0000000001 MAXEXTENTS 2147483645 PCTINCREASE 0 ) )
DbSlExecute: rc = 99
(SQL error 1452)
error message returned by DbSl:
ORA-01452: cannot CREATE UNIQUE INDEX; duplicate keys found
(DB) INFO: disconnected from DB
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: job finished with 1 error(s)
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: END OF LOG: 20071018195134
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: START OF LOG: 20071018195314
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#12 $ SAP
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: version R6.40/V1.4
Compiled Nov 30 2005 20:41:21
C:\usr\sap\BW1\SYS\exe\run/R3load.exe -dbcodepage 4103 -i C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.cmd -l C:\Program Files\sapinst_instdir\NW04\SYSTEM\ABAP\ORA\NUC\DB/SAPSSRC.log -stop_on_error
DbSl Trace: ORA-1403 when accessing table SAPUSER
(DB) INFO: connected to DB
(DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): WE8DEC
(DB) ERROR: DDL statement failed
(DROP INDEX "APTREET~0")
DbSlExecute: rc = 103
(SQL error 1418)
error message returned by DbSl:
ORA-01418: specified index does not exist
(IMP) INFO: a failed DROP attempt is not necessarily a problem
DbSl Trace: Error in exec_immediate()
DbSl Trace: ORA-1452 occurred when executing SQL statement (parse error offset=35)
(DB) ERROR: DDL statement failed
(CREATE UNIQUE INDEX "APTREET~0" ON "APTREET" ( "SPRAS", "ID", "NAME" ) TABLESPACE PSAPBW1 STORAGE (INITIAL 44981 NEXT 0000000040K MINEXTENTS 0000000001 MAXEXTENTS 2147483645 PCTINCREASE 0 ) )
DbSlExecute: rc = 99
(SQL error 1452)
error message returned by DbSl:
ORA-01452: cannot CREATE UNIQUE INDEX; duplicate keys found
(DB) INFO: disconnected from DB
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: job finished with 1 error(s)
C:\usr\sap\BW1\SYS\exe\run/R3load.exe: END OF LOG: 20071018195315
I'm getting this error "duplicate keys found". I'm finished installing the central instance and during the database instance, i got this error. I'm installing BW 3.5 on x64 windows server 2003 platform. I'm using NU kernel 6.40.
Thanks for your suggestions on how to resolve this error.
Reward points guaranteed.Issue solved by deleting central and database instance and started a new build. it finished without an error.
Thank you. -
Sad icon = computer does not detect = cannot put into disc mode !
hey,
my ipod photo at the moment won't turn on. the best i can do is plug it in to either my pc or the electricity supply, or reset it, so the apple logo comes up, however it only lasts for a few seconds and the sad face icon appears, directing you to www.apple.com/support.
i tried the first 4 r's and got onto the restoring one. but the updater will not detect the ipod. i think it is because my ipod is not in disc mode, but i cannot put it into disc mode - i can do the first step and resetting it, but then when i click the play/pause button and the select button nothing happens.
this problem has severly cheesed me off, and am very desperate to have a working ipod again!!!! please please help if you can!!!!
thanks a lot, leonHello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/ipod/download/
http://www.apple.com/itunes/download/
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iPod Updater and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iPod Updater and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921�
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call. -
Hi,
I'm trying to update the title block of the drawing in PROE with the Revision field after release of the DIR. The problem I'm facing is that the document cannot be checked out post release and hence I'm unable to update revision field in the Title block of the drawing.
Also the "Update Parameters" in .Reiss doesn't have "Update Revision" Option. Please let me know how I can achieve this.
Thanks in advanceHey Niranajan,
I understand we can continue versioning after release.
My question is about updating the title block parameters after the document is released (or in locked status), for example,
Example 1. I want the status in the title block to be changed from "create" to "In work" to "review" to "released" as the DIR status changes. I'm able to achieve "create" and then "In work" in title block as the status gets updated when I check out the document, but review and release are locked statuses so when I promote the document to relelase the status entry in the title blok isn't getting updated.
Example 2. I also want to update the revision of a released (i.e. locked) DIR in the title block.
I know this can be achieved by having custom code along with a conversion engine but would like to know any other simple updating techniques if any!
please let me know if you need more details,
Thank you -
Title block for Stickies - how to make?
I have (3) stickies on my desktop.
One of them has the first line of the text of the note in the Title Block when the Sticki is collapsed
The other two Title Blocks are blank.
I can't, for the life of me, remember how I created the first one.
Skickies Help doesn't seem to have an answer to this.
Anyone know how to do it?
Thanks,
DantyThanks, Charlie
It actually was THAT easy.
I had put my text a line down on the "empty" title block stickies.
Danty -
Hi All,
<b>under spro>>CA>>doc mgmt>> gen data>>define workstation appln>>define template fr oiginal files</b>
what is significance of this?
also,
<b>Can anyone send me doc on title block settings stepwise.</b>
screenshots would be gr8 help.
can some1 tell me where is user exit?
im using Inventor 11 sap integrator provided by cideon...
with points
Niranjan> Hey Rehman
>
> u r tooo good man
>
> points given
>
> i was thinkin on same lines for my 1st query
> still 1 query how can the template will be taken from
> SAP to CAD.
> i mean ll this be done at the time of saving doc or
> checkin.
> can u pl tell me the steps to follow to be successful
> in templatization.
>
>
> tell me @ second
>
> can u send any doc or screens on CAD Title Block.
> [email protected] is the mail id
>
> once again thanx fr help...
Hi Niranjan,
You are not taking a template from SAP to CAD.
In CAD Interface always you should work with CDESK i.e through CADDESK.
It is imperative to use the transaction CAD Desktop in Order to establish the link between the Cad drawing and Document Info Record(DIR ) while the drawing needs to be updated for title block entries.
The Following Procedure for working with CAD for Titleblock updation.
1. Open ACAD/Inventor , you see the SAP icon on the ACAD menu (top right)
2. Opend SAPview of CADDESKTOP i.e. AutoCAD/Inventor> SAP>CAD DESKTOP--->SAP VIEW.
3. Choose Working Directory for the Cad desktop log files.
Prefarably ( C:\Sap WorkDir\Acad or Inventor)
4. Enter DIR key (doc # + doc type ) you wish to edit
Result: SAPView tab is populated with DIR
5. Choose SAP View -> Originals-> Edi Originals
6. A Successful checkout shows ("File Copied")
7. choose "Execute" to edit the Original file. & Edit the drawing.
8. Save
This is the procedure you should follow to work with SAP-CAD when you have CAD Interface only this will update your Title block and likage will be maintained.
But you should use Function Module to mention all the Technical names of the Fields you need to maintain in the Title Block.
The in CFG File you need to map those fields.
i.e. in path
Cfg-File\LocalCfg\TbkMapping
Here you need to map all the required fields (DIR Fields in maintained in Function Module & the Template (ACAD/Inventor) Attributes)
Hope you are Clear.
Regards
Rehman
<b>REWARD POINTS IF USEFUL</b> -
I cannot print a picture using the paper in the lower tray and cannot make 8x10 paper fit in the upper tray. Is this normal for this printer. I should have stayed with a HP printer. I am using an iPad 2.
Actually both wireless problems are mentioned frequently on the web, by many people. I was finally able to figure a solution out because there were so many threads to choose from when you Google it...never had problems with any other wireless equipment connecting in all of the years we have used them, just this printer...As I said, a fan of Canon in all forms for years. Just not this printer. Regret giving up the MX850. Have gained nothing with this printer, techinically or print quality wise.. Feels like a step back, actually. And many others have mentioned how agonizingly long it takes to fire up to print or when you change settings. It is a major complaint with this printer. As to the Airprint info of the 4"x6" only printing, I was not aware of that. Maybe if printer manufacturers put that info in their sales material in the section dealing with Airprint, we would be able to manage expectations better....
-
HT4113 put wrong passcode now is blocked
put wrong passcode now its blocked .show ipad is disabled. connect to itunes
If you have forgotten the iPad passcode and you cannot unlock the device, you have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
Instructions can be found here.
http://support.apple.com/kb/ht1212
You may need to restore using Recovery Mode. You may have to try it a few times to get it to work..
You can read about it here.
http://support.apple.com/kb/ht4097 -
I updated my ipod on my computer to the ios 5.1.1 and it updated but all of the music, movies, and apps were cleared off. I cannot put any of it back on please help!
Go to iTunea>Preferences>Devices and see if there is a backupright at the time you did the update. Then try restoring from that backup. If the apps are in your iTunes library, any app data will be restored to the iPod.
When restoring from an iOS 4 (or later) backup, if the device had a passcode set, iTunes will ask if you want to set a passcode (and remind you that you had protected your device with a passcode). iTunes will not ask you to set a passcode when restoring from iOS 3.x and prior backups.
Therefore, remembe the passcode that you enter this time.
It appears that if you restore from a backup, that backup is not subseqyently overwritten by the next backup.
Maybe you are looking for
-
i have made a MYSQL_ECMA.dll (using sql_ecma.dll) but when i create that ECMA it is unable to create get_schemafrom my sql Database=test table=HR public Schema GetSchema(KeyedCollection<string, ConfigParameter> configParameters) Microsoft.Metadirecto
-
How to get the " com.sun.xml.* " package?
In a java xml sample, it uses a class "com.sun.xml.tree.XmlDocument". Its author said it is a internal class.But I can't find the class in "com.sun" package. Please tell me how to get the class? Thanks very much!
-
Restore in-app purchase after country/region change
Please let me get to the point: The scenario is I got an app from country X and made some in-app purchases for additional functions. Then I moved my account to country Y. If I happen to delete this app and later install it again, can I restore the in
-
Will Apple ever become entrenched in the Business Workplace?
The post Will Apple ever become entrenched in the Business Workplace? appeared first on PostmanMojo.com, Inc.. Read More This topic first appeared in the Spiceworks Community
-
I cant get my i touch to work and im sure im just doing something simple wrong.