Cannot read from the source file or disk

I had to get a new hard drive for my Satellite A665 old one kept freezing up; had a recovey disk from Geek Squad when I got it but they did not work.  So I ordered a Recovery Disc set from Toshiba. 
A few minutes after I insert the 3nd disc, I get the following message:
Cannot read from the source file or disk
PREINST14.SWM
Type: SWM File
Size:  670 MB
Modified: 10/29/2010 11:24pm
Clicking [Try Again] or [Skip] clicked try again twice. Gave same message so clicked skip. Got another message.
Cannot read from the source file or disk
PREINST18.SWM
Type: SWM File
Size:  372 MB
Modified: 10/29/2010 11:24pm
Clicking [Try Again] or [Skip] clicked try again twice. Gave same message so clicked skip after checking do it for next one. Got error message.
An error has occurred.
Error:  10-FC06-0002
Recovery Error.
Please press [OK] to turn off the computer.
I tried erasing the disk, then running the Recovery Wizard again, but wind up in the same place.

It's hard to know exactly what the problem is. You might want to contact customer support because it could just be a faulty disc.
- Peter

Similar Messages

  • After updating I ended up with 4 icons on my desktop - I cannot delete any of them. The error message reads; "Cannot read from the source file or disk".

    I updated from the original version to 6.0.1 and when I re-started FF there were 4 icons on my desktop. I managed to delete one of them, but I cannot delete the other two - to leave me with just one.
    I get the error message of "Cannot delete file: Cannot read from the source fie or disk".

    Here's the meaning of the error that you received.
    "An error has occurred. ERROR :10-FC06-0002" -- may be caused by damaged recovery media or faulty hard drive"
    Possible that the problem is on the recovery also.
    Hope this helps.

  • Windows Easy Transfer (WET) Issues with External Hard Drive - "Can't read from the source file or disk"

    I work for Office Depot, in the tech department. Basically, one of our associates was supposed to do a data backup, and re-install Windows 7, then transfer the files back. He used Windows Easy Transfer and compacted everything into a 163 GB file. 
    Now comes the hard part. When we try to put it back on his computer ((drag-and-drop to the desktop) which has been wiped back to factory settings using the recovery partition), it stops at 79.5 GB remaining (you know how it doesn't give you a % of completion,
    it just shows how many GB are remaining) and then says "Can't read from the source file or disk" and gives you an option to try again, or cancel. It gets hung up on the same point each time.
    Normally, this wouldn't be a huge issue, but the contents on the drive are his wife's architect blueprints and interior design stuff, along with wedding photos, etc, which are the only copies they have. On top of those, they have court documents and other
    important files that we are unable to access now.
    I wasn't involved with this transfer, so I'm trying to clean up the mess as best I can. I remembered that the customer's wife was Russian, and had some files typed with a Russian keyboard, so on and so forth. I wonder if that's the issue? If not, I really
    have no idea how to manually extract things from a ".mig" file, or how to diagnose what area is potentially corrupted.
    In light of this situation, we tried using "Recuva" to recover the files post-wipe, but everything was corrupted or unable to be opened, and it also extracted and recovered all of the "useless" photos, such as the skype logos, up and
    down arrows for browsers, etc (it was 160,000+ photos).
    Trying to avoid a potential lawsuit, unhappy customer, and costing the company lots of money to see if professionals can get into this external hard drive.
    Other relevant information:
    We used a Toshiba 500 GB (465 GB) external hard drive.
    Customer's computer is an HP Pavilion P6000 Series (Model No. p6520y) running Windows 7 Home Premium 64-bit Service Pack 1.
    Any other information that is needed can be provided, thanks in advance, and hopefully we can find a solution to this issue quickly!
    -John

    I think there's a lack of understanding somewhere.
    "If you even can't start the process, please unplug it from your new PC. Then head back to your new computer and plug
    the external drive back in to your new computer. "
    Unplug from new, head back to new, plug it back in? That doesn't make much sense! Haha.
    I knew what you meant though, somewhat. When I search through the drives after clicking yes (Has windows easy transfer
    already saved your files blah blah blah) I click on the transfer file and it says "Windows Easy Transfer could not open the file".
    Rather than drag-and-drop the file to the desktop, I now tried to double-click on the file itself while it was plugged
    into the computer. It opened, and it started transferring until it was about 70% completed, and then an error popped up saying "WET can't open the easy transfer file, make sure your USB device is plugged in or check your internet connection". 
    I checked, and the USB hard drive's light wasn't on. Now, I unplug it and plug it back in, and the light comes back on,
    so I click Retry, and it resets the bar back to nothing and says "Transfer time: 1 minute".
    Rather than continue trying, I clicked "Cancel" instead of Retry, and it says "Your transfer did not complete successfully."
    It says to click "view report" for more information, but there's no "view report button".
    At the moment, I am scanning the External Drive for bad sectors using the check disk tool in properties. It's frozen
    at "0 USN bytes processed".

  • Error: cannot read from the source file ....... the file cannot be accessed by the system. (Exception from HRESULT: 0x80070780)

    I have sync toy set up to sync my Skydrive with some folders on my local drive.
    I'm running windows 8.1, 64 bit
    I can copy files from my local drive to the Skydrve folder with no problems,
    but if I add files to my Skydrive, and then when Sync Toy runs it will not copy the files from Skydrive to the local drive and throws up the error in the title.
    I have tried changing permissions on both folder pairs with no luck.
    Any ideas?

    Try making the OneDrive files available offline.
    See
    http://windows.microsoft.com/en-gb/windows-8/onedrive-online-available-offline?woldogcb=0.

  • Encore CS4 error "could not read from the source file"

    - Source File: C:\Users\Anil\AppData\Local\Temp\2013 11 08 c Big Budha_9.prproj
    - Output File: F:\Adobe Encoded Blu-ray\For Disk #013\Disk#013-B\2013 11 08 c Big Budha.m2v
    - Preset Used: Full HD 1080i [MPEG] 30 MBPS
    - Video:
    - Audio:
    - Bitrate:
    - Encoding Time: 01:49:53
    25-Jan-14 2:50:32 PM : Encoding Failed
    Could not read from the source. Please check if it has moved or been deleted.
    i have tried creaeted a NEW Premiere Pro project and still get the same error again ... can someone help me to figure out what is wrong ...

    Hi Neil
    I have been using file names with spaces and it has been working fine. As stated in reply to Jones, uninstall and reinstall of Premiere Pro CS4 has helped to get rid of this error.
    also i did not use Dynamic link, but was trying to create MPEG file using Media Encoder and then import it in Encore.
    your suggestion for H264 seems good and will try it.
    x264 Pro is for CS5 and above versions, so it seems i can not use it and have to manage with Adobe Media Encoder's default. Hope i will not have any major technical issues.
    please suggest me for below:-
    1) i have 4 hours of Full HD footage and made 1080i MPEG2 files of 30mbps to fit in 2 seperate Bluray Disks.
    2) now i plan to put all in one Single Bluray Disk by reducing MPEG2 file average data rate to 15mbps. will that work or is there any limitation of time in Bluray Disk.
    3) Will it be ok to create H264 files at 30mbps [as you mentioned H264 reduces file size to half of MPEG] and still be able to fit 4 hours footage in one BR Disk ?
    4) even though i specify Min 10 Target 25 Max 30 data rate for MPEG files creation, it creats file at data rate of 30 mbps, can you explain why it is happening as i thought my target rate should be 25 mbps and not the maximum rate specified.
    Thanks ...
    PS...
    my source file is .mov 1920 x 1080i 29.97 fps from Canon 6D. first i tried to create progressive file in Encoder but while imported in Encore realised at 29.97 fps, it allows only interlaced file and had to transcode back to interlaced. so i stick to interlaced file.
    Canon 6D also allows me to shoot in 24fps [motion movie] which Encore can handle as progressive file for authoring. What are the pro and cons of shooting in 24fps, if you can suggest.
    Message was edited by: AnilHVarma

  • Getting error Can't read from the source or disk when moving documents from one folder to another folder in the library

    Hi,
    When we try to move documents from one folder to another folder in the document library using "Open with explorer" getting beloe error.
         Can read from the source file or disk.
        The user having below permission for the Library as well as site.
    Fullcontrol,Limited access--->Given directly
    Read,Limited access--->Givin through the all Test grp
    Contribute,Limited Access-->given through test members grp
    Read,Limited access---> givin through The group grp
    Could you please help me anyone....
    Thanks

    Hi Reddy,
    If you are moving files in two libraries in different sites, then the error will occur and it is by design that there are limitations on the DAV move commands that the DAV client is respecting.
    https://social.msdn.microsoft.com/Forums/en-US/6245f332-c609-4a7b-8e00-c8b5e46f7759/cant-move-files-using-windows-explorer-cant-read-from-source?forum=sharepointgeneral
    If you are moving files in the same library, I recommend you to use Wireshark to reveal the error message and enable IIS
    Trace Logging for Failed Requests to examine the IIS log file for troubleshooting.
    https://social.msdn.microsoft.com/Forums/en-US/47cd569d-98f2-4cca-b78e-fd178c097285/cant-read-from-the-source-file-or-disk?forum=sharepointgeneralprevious
    To narrow down the issue scope, I recommend you to test with another library and see if the copy in explorer can work.
    Best regards.
    Thanks
    Victoria Xia
    TechNet Community Support

  • Encoding Failed- Could Not Read from the Source

    I have a quickly approaching deadline for the short film I am working on, and it would be greatly appreciated if anyone knew anything of my predicament.  Everytime I try to export anything from Premiere Pro (CS4 of course), when I start the queue it says "Could Not Read from the Source.  Please check if it has been moved or deleted."  The files, of course, have not been moved or deleted, and the raw footage for the film is in the same place as everything else.  All my scratch disks are set to the same folder, etc.  I don't understand, and it won't even let me export to my camera.  It says it does, but when I check my camera, it's nothing but blank tape.  Any (quick) help would be very much appreciated!
    Thank you.

  • Error 1901. Error attempting to read from the source installation database

    OS: Windows 7 Enterprise 64-bit
    Browsers: IE 9 and Firefox 10
    Flash Version 11.7.700.169
    I'm logged in as Administrator.  I'm trying to install using this:
    start "" /wait msiexec /i install_flash_player_11_active_x.msi /qb
    and
    start "" /wait msiexec /i install_flash_player_11_plugin.msi /qb
    Both commands result in:
    Error 1901. Error attempting to read from the source installation database: C:\Windows\Installer\3c0cc1.msi
    (the file name seems to be random)
    echo %errorlevel% returns 1603.
    Help.

    Not sure how much I can help you with this.  Error 1603 usually indicates that the installer cannot proceed because something is in use; search this page for 1603: http://msdn.microsoft.com/en-us/library/windows/desktop/aa372835%28v=vs.85%29.aspx

  • Adobe Media Encoder for CS4 error Could not read from the source

    Hello,
    I get an error when I try to export from Premiere CS4. It doesn't matter how I export. Seems like an easy fix, but I can't figure it out. Any help is appreciated:
    - Source File: C:\DOCUME~1\ARTWHI~1\LOCALS~1\Temp\extra and b roll.prproj
    - Output File: E:\Living Accused Movie Transfers\video\Cindy at table.avi
    - Preset Used: NTSC DV
    - Video:
    - Audio:
    - Bitrate:
    - Encoding Time: 16:10:34
    1/21/2009 9:50:25 PM : Encoding Failed
    Could not read from the source. Please check if it has moved or been
    deleted.
    Thank you
    Art

    When you attempt to encode media with Adobe Media Encoder CS4 on Windows, the following error message appears in the text file (AMEEncodingErrorLog.txt) that opens when you click the error icon: "Encoding Failed. Could not read from the source. Please check if it has moved or been deleted."
    If it's that correct, you removed an earlier version of Adobe Premiere Pro or Adobe Creative Suite on the same computer.
    Do one or both of the following solutions:
    Solution 1: Create a shortcut to the Premiere Pro executable file, rename the shortcut to Premiere, and move the shortcut to C:\Program Files\Common Files\Adobe\dynamiclink.
    Close all Adobe applications.
    In Windows Explorer, navigate to C:\Program Files\Adobe\Adobe Premiere Pro CS4. (If you installed Premiere Pro CS4 in a location other than the default of C:\Program Files\Adobe, then navigate to your custom installation location.)
    Right-click on Adobe Premiere Pro.exe (which might appear without the .exe extension) and choose Create Shortcut.
    Rename the newly created shortcut to just Premiere.
    Important: The name of the shortcut must be exactly Premiere with no other characters.
    Open a second Windows Explorer window, and navigate to C:\Program Files\Common Files\Adobe\dynamiclink.
    Move the Premiere shortcut that you created into the dynamiclink folder.
    Solution 2: Remove and reinstall all Premiere Pro CS4 components or all Adobe Creative Suite 4 components.
    Do one of the following:
    Windows XP: Choose Start > Control Panel > Add or Remove Programs.
    Windows Vista: Choose Start > Control Panel > Programs and Features.
    In the list of installed programs, select Adobe Premiere Pro CS4, Adobe Creative Suite 4 Production Premium, or Adobe Creative Suite 4 Master Collection.
    Click Change/Remove (Windows XP) or Uninstall (Windows Vista).
    Follow the on-screen instructions to remove all components of Premiere Pro CS4 (including Adobe Encore CS4 and Adobe OnLocation CS4) or to remove all components of your edition of Adobe Creative Suite 4.
    Re-install your Adobe software.

  • Could not read from the source. Please check if it has moved or been deleted

    hi all,
    when i try to render a afx project from media encoder i get the following message
    "Could not read from the source. Please check if it has moved or been deleted"
    i've read on the forum that this is due to an old installation of Premiere.
    I'm using a brand new computer. the only software installed is my cs5 master collection and the updates from adobe website.
    win7 pro
    i7
    16 gig ram
    cheers
    s

    Hello, this is terrible problem, which i found in CS 6 softwares ...
    solution i found only working, is uninstall and reinstall full package.. but it is not all,
    you need to do BRAND NEW admin account in windows, and install it there.
    that means, i could not export after repair from encoder in my original account never more (!!)   .. this is really terrible way how to repair this issue, because :
    1.by reinstalling of software, client WASTE HIS TIME
    2.by necessity to begin work in another windows profile you again WASTE YOUR TIME because of learning and migrating all other profile modifications, which i see really unaccpetable. Adobe means, this solution of repair is ok, and they did not do till today any steps of creating some "clever" solution.
    I ask everybody, who will meet this issue in future, guys, please, complain about this situation, give "BUG Report" to them, and write "feature request" to them , in the way of creating some repair tool, which check actual  "broken" connections between encoder and premiere, which refuses to "take material" from it and encode, and REPAIR it automatically..  
       I am not IT, but ..does it seems so hard to create this ? Adobe IT developers should know their systems, and should create such utility tool really easy.
    Steps to reproduce bug:
    1. i export anything by button "queue" from premiere to Encoder
    2. Encoder will start encoding
    3. Encoder does not show the window of media encoding (down left )
    Results: sound of sheep occur,
    in encoding error file is this reason of canceling the encoding :
    01/02/2014 10:10:48 AM : Encoding Failed
    Could not read from the source. Please check if it has moved or been deleted.
    History of this problem and detailed description, HOW i did "repair" this. With wasting of app 2,5 days of my working time :
    1. after repairing "error 5" problem , i solved it by reinstalling the suite from the new admin user profile (profile B) . 
    I continued my work on my normal working windows profile . (profile A)
    Every cooperation (AE+Pr, export media via "queue" to Encoder) was working fine . . .
    2. suddenly it stop working (without knowing any possible reason - i did not do installations )
    and showed in error export log file :
    "Could not read from the source. Please check if it has moved or been deleted."
    3.repair via procedure(procedure "a"):
    i did this procedure on the profile B (profile from last time installation of repairing problem error 5)
    I did these steps :
    a-uninstall master coll suite
    b-i used Adobe cleaner tool (remove ALL)
    c-removed raw directories in locations
    •C:\Program Files\Adobe
    •C:\Program Files(x86)\Adobe
    •C:\Program Files\Common Files\Adobe
    •C:\Program Files(x86)\Common Files\Adobe
    •C:\ProgramData\Adobe
    d-removed these links from registry file
    •HKEY_LOCAL_MACHINE\SOFTWARE\Adobe
    •HKEY_CURRENT_USER\Software\Adobe
    •HKEY_LOCAL_MACH INE\SOFTWARE\Wow6432Node\Adobe
    •HKEY_CURRENT_USER \Software\Wow6432Node\Adobe
    e-restarted the PC
    f- newly installed the Master Coll CS6
    g-update the software
    result of repair of "3" : problem still exists
    4.Ok i find out after coordination with support, it should have been created  ANOTHER NEW admin account.
    4a:so i did the same procedure (uninstalling) in profile B
    4b: and then i created brand new admin profile (profile C)for INSTALLATION of software
    4c: restarted the pc (and did not updated it yet)
    result :
    ==exporting of any sequence/raw/AE link video material from premiere via "queue" (Encoder) (profile C) : export WORKS
    ==exporting of any sequence/raw/AE link video material from premiere via "queue" (Encoder) (profile B) : export WORKS
    ==exporting of any sequence/raw/AE link video material from premiere via "queue" (Encoder) (profile A) : export DOES NOT WORK ! ! !
    (in profile A, is possible to export some raw video material in encoder which is imported to it via "drag and drop)
    problem i see:, i have my basic profile A, which i am interested to work, because of all my directory modifications are in there..
    this issue should be some "broken" connections between encoder and premiere, which refuses to "take material" from it and encode.
    what i expect :
    to get from Adobe some repair tool, which automatically checks these connections and repair if necessary, without necessity of founding the new profile and reinstallation of whole software.. this is madness !
    what i do NOT expect from Adobe:
    to get from Adobe advice of kind : you have to reinstall full software in new admin profile. sorry , we do not know the solution, because we do not know, how do behave our software.

  • Installed CS5, now can't export from CS4! Help! "Could not read from the source..."

    I installed CS5 but completely ignored the fact plugins were required to be 64-bit. It'll be months before the plugins I require for my projects to be updated!
    So I continued editing in CS4 and when I attempted to export with the media encoder it halts instantly with an exclamation mark, the log says :
    "Could not read from the source. Please check if it has moved or been  deleted."
    And yes I'm not stupid, I did my research.
    I tried uninstalling CS4 and reinstalling. I tried the shortcut fix. I tried moving my cache files. My extensions are correct.
    Right now the only fix seems to be completely removing CS5 and CS4, After Effects just because they share files (?) and all my settings and plugins along with it! I'd rather NOT do that if I can!

    Good detective work, and glad that it worked. Now, your cure will be here for us to link to and for others to find. Your title will help direct others to this thread. Job well done.
    Thanks,
    Hunt

  • CS4 Pr-Encoder: "Encoding failed/Could not read from the source..."

    When i start queueing it apears to be loading fine but then after a few minutes it gives me the yellow hazard triangle on the status column. I have tryied changing settings and still the same.
    "Could not read from the source. Please check if it has moved or been deleted."
    ...is what the details notepad displays
    This is my first Pr CS4 editing, Please help.
    Thanx!

    latest versions of CS4 and snow leopard 10.6.1.
    May have no part in your problem, but many are having real issues with almost anything Adobe with Snow Leopard. There has been a lot of chatter saying that Apple is aware of this, and is working on an OS update to be released soon.
    While I have not seen this particular issue with Snow Leopard, there have been so many more, that I'd certainly put the OS into the list of "usual suspects." In the Encore forum, some had great success by rolling back the OS to whatever was prior to Snow Leopard, just plain old "Leopard?"
    Wish I had a definite cure for your ills, but the best that I can offer is that it does not seem that you are alone.
    Good luck, and I hope that the Mac OS update does fix things for you.
    Hunt

  • Media Encoder - encoding failed - could not read from the source

    Using PPCC, AME queued jobs all fail with the message "Encoding failed. Could not read from the source".
    But doing a simple export works perfectly.

    I recall quite a few other threads about this.  Do a forum search.

  • Accessing comapny code from the source file name

    Hi,
    Iam doing FILE –FILE to scenario.
    My source file name is XXXX237061606.txt. (XXXX is company code)
    My requirement is …
    Based on company code from the source file name; I need to send the file to the corresponding receiver.
    How to retrieve the company code from the source file name?
    Thanks,
    Hem.

    hem chand wrote:>
    > Hi Varun,
    >
    > Could u please provide me detailed procedure to get the company code.
    >
    > Reg,
    DynamicConfiguration conf = (DynamicConfiguration) container.getTransformationParameters().get(StreamTransformationConstants.DYNAMIC_CONFIGURATION);
    DynamicConfigurationKey key = DynamicConfigurationKey.create("http://sap.com/xi/XI/System/File","FileName");
    String ourSourceFileName = conf.get(key);
    This will get you the File name...TRuncate it to extract company code...
    Then have a mapping program with the receivers message type which is persent under SAP BASIS component....
    There map to the required receiver by getting the file name above..
    Create an int mapping for the above mapping and use that in ur enhanced recv determination

  • The system cannot read from the specified device

    What do I do? ive tried on two computers and it says it on both computers when im trying to install! ive looked at all the troubleshooting pages and it doesnt say anything... my computer says the ipod is connected but when i try to install itunes it says that it cannot read from the specified device please help

    hi parkep!
    are you getting an error message number with that error message? if so, what is it?
    are you installing from the CD, or are you using installers downloaded from the Apple website?
    iTunes 6.0.4.2 Installer
    Ipod Updater Installer
    love, b

Maybe you are looking for