CANNOT record in plain STEREO!!! Everything outputs to MONO inste

system specs:
e6750 C2D
2 GIG DDR2 RAM
X-fi xtreme gamer
Abit IP35 Pro
Drivers 2.00.09
Under audio creation mode I am trying to record with "What you hear" selected, and either WMA or WAV stereo. While playing a stereo mp3 with two discrete channels, the monitor reflects two discrete channels, but the recording monitor just shows mono (both left and right are doing the same thing). sure enough upon hitting record i only get a mono output with the RAW file. The other problem is even if i try to record with a different program (Nero Wave Editor and even Sound Recorder) I still get a mono recording and for one reason or another, the bit rate sounds much lower even though i select 6bit, 44KhZ.
the only workaround I've gotten was to record under 'multi-channel wave' format, then mute all the other channels except for front L/R. however this contributes to a obnoxiously large RAW file. why can i get a simple stereo recording?

Try this:?Go to "recording devices."?Select the device you are using. Click "properties" of the device you are using. Click "advanced" tab. If your set up is like mine, you will see a window with different recording modes, and a mono recording mode is selected by default. Select a two-channel mode and your problem should be solved.

Similar Messages

Cannot hear headphones in stereo. Feels like mono sounds.

After using this youtube example (https://www.youtube.com/watch?v=hTvJoYnpeRQ) to determine if my headphone is working or not I noticed that I can hear the left channel on the right side of my headphone and the right channel on the left side of my headphone (Essentially, I can hear both channels with just one side of the headphone). This is irritating me as when it comes to some games (Such as Counter-Strike: Global Offensive where listening and determining where noises are coming from), it is crucial to learn where the sources of the audio is coming from. This even happens when I listen to music and I get confused if it's from the left side or the right side of the music when the music I listen to does take advantage of 2+ channels. I have tried it on my old laptop and it can listen to both channels seperately, just fine.
The laptop I am using the HP Envy 15-j058ca and I currently have the latest audio driver on it for 8.1 with the latest Windows updates. Is there something I can do to be able to listen the left and right channels on proper sides instead of hearing it as if it was mono? Thanks in advance!

Please try to update the PC's audio driver if you haven't done so already.
Link:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-124012-1&cc=us&dlc=en&lc=en...
Once installed go to the audio control panel or click on the little sound icon on the bottom right corner of your screen and click on the little Speaker/Headphone Icon above the volume slider.
Once you do that, you will get a window like the one below with General tab highlited.
CLick on the Levels tab and then click on the Balance Button. Move the sliders to check if there is actually an issue with the RIght or Left channels and if the correct channels respond when you move the individual sliders.
Also try with another Headphone.
I'm an HP Employee.
The opinions expressed here are my personal opinions, not of HP.
Click on Thumbs up if my post helped you.
Make it easier for other people to find solutions, by marking an answer “Accept as Solution” if it solves your problem.

Cannot record stereo track along with built-in camera

I'm hoping since imovie 6 is considered superior, by some, to more recent versions that knowledgeable users are still following this forum. I've got a pair of stereo mics going through a lexicon usb interface -- chosen as the input in audiomidi setup -- but imovie will only record them in mono. The same mics record fine in stereo for audio applications such as garageband. The best I can deduce is that when using my macbook's built-in camera -- that is, clicking 'record with isight' -- imovie will receive the audio from the interface, but only in mono -- as would be the case were I using the built-in mic as well. What has your experience been?

When you open iMovie look at the switch under the screen. You will see a camera on the left of the switch and scissors on left. Flip the switch to the camera and the built in camera should come on. Then on the screen it will say record with isight. That starts the record.

Error "You cannot enter a partner function for output NEU"

Hi Experts,
I'm having these error "You cannot enter a partner function for output NEU" (message VN041) when I tried to assign a partner function (e.g OA) in the conditions records for application "EV" (Purchase outline agreement). The system do not allow me to do this for any doc type (LP, LPA, MK, OA, etc). I'm using t-code NACE or MN08.
I want to assign partner for key combination "Document Type". The conditions is already there but with no value, so I want to assign partner function "OA" or "VR".
I already check all the configuration and looks fine. For example, define possible partner functions for output type "NEU" for application "EV" (Purc outline agree).
Hope you can help me to find the problem.
Thanks,
Mairo.

I have the error in NACE or using tcode MN08.
As soon I executed those transaction the system shows the condition records created for varios Doc Type (e.g LP, LPA, MK, etc) but with no partner function assigned. For example:
Doc. Type / Name                     /             Funct /   Partner     /            Medium / Date/time /   Language
LP        /       Scheduling Agreement     / blank / blank /                                          2      /          3   /              EN
LPA      /      Scheduling Agreement                              / blank    / blank   /                1        /       3         /        EN
For example, I try to assign function "OA" for Doc. Type "LP", choose value from quickpick. Then when I press enter, the system give me the error "You cannot enter a partner function for output NEU", message no. VN041. Do not allow me to continue, so I have to leave this field blank, with no change.
Thanks,

Recording from a stereo

How do I set up a voice memo recorder to record from my stereo? It should be possible (as the manual on the voice memo recorder briefly notes, and Apple confirms), by switching the button behind the microphone from "mic" to "line." But so far I've only succeeded in getting a message that no microphone is connected. Ordinarily I have an AV cable hooked up in a way that works for sending music from the ipod to the stereo -- connecting to the output jacks for a VCR, since all the others were in use by cd player, tape deck, and phonograph player). But when I try switching it to the input jacks and recording an old LP, I get only the error message, whether I plug it into the place where the microphone goes or instead where the earphones go (which I guess can't be right) on the ipod. Can anyone explain what configuration would work? Am I right in assuming I don't need any further wires?
Dell Latitude D610 Windows XP
Dell Latitude D610 Windows XP

Hi,
Are you trying to upload to your computer, the audio tracks on old LPs played on the stereo? If so, probably a better way to go is to get a second set of audio cables to go from the audio/line-out jack of either the phonograph or amplifier (depending upon your stereo's setup) to the audio-in jack at the back of your Dell (assuming you have a sound card installed).
I suspect if you use the iPod Voice Memo mic for recording the LP as it plays over-the-air so to speak, the quality won't be great. Better to input directly into the sound card the audio output produced by the stereo.
Depending upon what you want to do with the audio tracks once it's on the Dell, you can get other pieces of hardware, such as an M-box, or software to further clean up to sound, before you import it into iTunes (for example).
Ed

Cannot record through line-in in bootcamp MBP late summer '09 model

cannot record through line-in in bootcamp MBP late summer '09 model
audio source (mp3 player) <3.5mm male input-------------3.5mm male input> line-in to macbook pro late summer 2009 model bootcamp windows xp sp2
when i select microphone in the audio panel - it works
when i select line-in and plug in the 3.5mm jack input to 3.5mm jack input to a fm radio for ex. it doesn't work
how do i make the line-in work?
i remember that when i first installed mac osx sl and windows xp bootcamp - the first couple of times around when partitioning the hd - the line-in worked a couple of times, in between times somewhere along the line i made some change to the spdif settings ?? or driver / to make the red light that comes on in the line-in jack go away - the other method was to use a toothpick to push a tiny button inside the jack, did that once -but the redlight came back again after a restart on bootcamp side.
thanks in advance,
-r

Although I don't use it, the Line-Input jack should require a signal about 40dB higher than what a microphone alone puts out. If your cable only adapts the connector and does not provide amplification, I'm not surprised you get nothing. If you are lucky, you MIGHT get a low signal by going into System Prefs/Sound/input/line-in and turning the input level slider all the way up. But the real answer to to get a mike preamp or mixer, or a mike with line-level output. Some products take a mike input and convert it to digital into the USB port.

After upgrading to IOS8.1 my microphone stopped working. cannot make a call, cannot record a voice memo, but Siri works !!!

after upgrading to IOS8.1 my microphone stopped working. cannot make a call, cannot record a voice memo, but Siri works !!! Surely this must be software since I presume there are not two microphones, one for Siri and one for everything else. Tried resetting, rebooting, switching off noise cancelling. What else is there?

Hi there hansadj,
You may find the microphone troubleshooting steps in the article below helpful.
If your voice is too faint or sounds unclear using iPhone, or iPod touch
-Griff W.

How to link two recording channels for stereo?

I have a zoom 6 interface which naturally records vocals in stereo with audition with its built in stereo
Mic. However, I have an external stereo mic which connects to two different inputs on my interface.
I want to link these two inputs in audition to record in stereo without recording two separate busses.
How can I do this?
Thanks!

You need to select a stereo input option in the channel sources choice on the track control panel (LHS). If it's possible to pair the two inputs, then this is where you do it.
Alternatively, just don't bother! Simply record two mono tracks and mix them down to a stereo track afterwards. Mind you, if you are recording vocals like this, then there really isn't a lot of point, as your voice is mono anyway, and you only really need a single output from the mic - one side or the other would do. If you are recording ambient sound, then okay, stereo - but you really don't need that for a single voice.

Cannot Record Rosetta (Toslink)

Can someone please tell me what could be wrong with my setup? I'm new to Logic from Cubase.
The input and output is from the G5 (toslink)to the Rosetta (toslink). From the Apple's system preference (sound), I can clearly see the signal from the Rosetta, but I cannot record this signal into Logic 7. The audio track is selected, the record button is enable and the Audio Core is ready.
Will someone please tell me why I cannot record? The signal is there.
Thanks,
Daz
Mac OS X (10.4.7) Dual G5, Logic Pro7, Rosetta 200

I had some problems like this with a digidesign driver.
It would not let me use the spdif with logic. I am not
familiar with the Rosseta, if it has a driver program,
see if you can find anything like a manager interface
that might have the settings you need to tweak.

Cannot record anything! (Audigy2 Plat

The problem I'm having is that I simply cannot record anything.
I tried different things including setting the source to "What U Hear". I can hear everything from all inputs, but when I record into a file, I alway get an empty file.
Does anybody have any clue what might be going wrong here?

... Have LG RW Dvd drive when I insert a new DVD, and click properties on the device, shows that the disc has no free space
Hi,
To my understanding, that is the normal behaviour for new (blank) DVD.
You need to install DVD writer software application (e.g. Roxio Creator, etc) in order to write files into the DVD disc. Most DVD writers comes with such free software, so do check again for any CD that comes with the writer, or download freeware
from the Internet.
Hope that helps.
Cheers,
Tas Chew

I can record voice memos fine using the built-in iPhone 4 mic. And my Bluetooth headset (Jawbone Era) works fine when I leave messages on voice mail systems etc. when calling on the iPhone 4. However, I cannot record voice memos with my Bluetooth mic.

I can record voice memos fine using the built-in iPhone 4 mic. And my Bluetooth headset (Jawbone Era) works fine when I leave messages on voice mail systems etc. when calling on the iPhone 4, so it appears my headset mic is fine. I can also use voice activated dialing, although it fails miserably interpreting numbers. However, I cannot record voice memos with my Bluetooth mic. I just get barely audible static. Any suggestions? Thanks.

Hello, did you ever get an answer to your question? I just picked up a Jawbone Era and using on an iPhone 4s running 5.0.1. Seems to work fine on regular calls, but not on the built in Voice memos application. It worked fine on my older Jawbone Icon, but haven't tested on the 4s or iOS 5.
Thanks!

My mac's keyboard is not working with my mac.the green light blinks and i cannot get onto my mac. everything on the support questions does not help because i cant go on the mac and i cant sign in

my mac's keyboard is not working with my mac.the green light blinks and i cannot get onto my mac. everything on the support questions does not help because i cant go on the mac and i cant sign in

If you can't sign in, then you can't troubleshoot and/or pair the keyboard until after that........ so, for that, you will need to borrow someone's USB wired keyboard in order to get signed in and to the Keyboard Bluetooth Preferences.

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Hello Cloud19,
The article linked below provides some helpful information and troubleshooting that can help resolve issues with AirPlay and your Airport Express.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Cheers,
Allen

G/L account cannot record in the business transaction.

Dear Experts,
When i am using cash journal (FBCJ), some G/L account cannot record in the business transaction. (error msg: you cannot enter tax code in business transaction).
I want to know how to edit the business transaction to disable the tax code requirement for those G/L account
Regards,
Wilson

Hi
If you want to disable the tax code requirement for that particular GL a/c XXXXX.
1) In FS00 Please chck if there is any tax category specified(under control data tab), please ensure that no tax code is specified.(this particular chk mark will make the gl account as tax relevant)
2) if no tax code specified in fs00, you need not specify anything in the transaction code FBCJC2 (For that business transaction) in the field tax code.
3) So at the time of posting transaction in FBCJ it will not give any error.

Stereo 3D output solution?

Greetings,
I'm interested in stereo 3D content production via Adobe After Effects, but would like to be able to preview on the same computer/monitor. I'm working in OSX, but am not opposed to rebooting to Win 7 when I need to preview in 3D, if need be.
Has anyone been successful with using any 3rd party "middleware" to allow stereo 3D output to a 3D-ready monitor using the Radeon 5870 in either OSX or Bootcamp?
I'm also holding off on buying a new monitor for this system until I can find a solution, since they 3D-ready monitor may need to be specific to the solution.
Any info would be much appreciated.
Thanks,
Brian

the high end nVidia Quadro 4000 card has 3D stereo output support. You may want to check the nVidia web site (things like the Quadro product pages or the developer/community web boards) for more info. The card is just starting to ship this week, but there may be feedback from testers, nVidia staffers, and others more familiar with the process.
Good luck!

CANNOT record in plain STEREO!!! Everything outputs to MONO inste

Similar Messages

Maybe you are looking for