Cannot restart using 4 RAM Modules on 655 Max HT Ready (MS-6730)

When I use four 512MB RAM modules, my computer starts up and works fine. The only problem is, that I can't restart the it (D-LED boot-error: Memory Failure). To make it run again i have to turn it off and unplug the power cable.
When there are only two RAM modules installed (slot 1 & 3), everything works fine.
What settings do I need to make in the BIOS that it works with all 4 memory modules?
I got four identical and tested Kingmax DDR333 Ram 512MB (MPM33d-383, http://www.kingmax.com/product/pro_deskMPMC22D-38KX3.htm)
my pc-configuration:
655 Max-FISR (6730) v1.0
BIOS A6730SMS v 1.1
P4 2.67
Windows 2000 Pro SP3
4 x 512MB Kingmax DDR333 (MPMC22D-383)
MSI Ti4800SE-VTD
Thermaltake 420W; 3,3V/30A; 5V/40A
Ricoh DVD+RW
Seagate Barracuda ATA V 120GB S-ATA
thanks and cheers

buenas wonkanoby
thanks for your reply. finally i made it work: its this freaky kingmax-ram....
i exchanged two of the kingmax modules by veritech modules and everything works fine now. instead i got problems now with an MSI 648Max-L Board from which i took the veritech memory......
so if anyone else reads this:
[size=15]IF YOU GOT AN MSI 655 MAX OR 648 MAX AND YOU WANNA USE TWO OR MORE MEMORY MODULES GET VERITECH DDR333/512MB (OR WHATEVER) BUT DEFINITELY NOT CRAPPY KINGMAX DDR333/512MB!!! [/SIZE]
cheers and enjoy :D

Similar Messages

Can I install an 8Gb Ram Module on a 2010 Imac?

Acording to apple support iMac (Mid 2010): Memory specifications - Apple Support, "You can use RAM module sizes of 2 GB or 4 GB in each slot", but clearly is more cost efficient to be able to install an 8Gb and a 4Gb, as the iMac already comes with two 2Gb modules, the iMac only takes 4 cards and it has a max RAM memory capacity of 16Gb.
Can I install a 8Gb?
Thank you!

For the 21"
Maximum Memory
16 GB
Memory Slots
4 - 204-pin PC3-10600 (1333 MHz) DDR3 SO-DIMM
For the 27"
Maximum Memory
32 GB (Core i5 or Core i7 Actual) 16 GB (Apple)
Memory Slots
4 - 204-pin PC3-10600 (1333 MHz) DDR3 SO-DIMM

17" iMac (1.6Ghz PPC) can use Ram with Heat Spreader?

Hello There Apple Community,
i have a vintage 17" PPC iMac, it support 2GB of max ram., here in my country those memories are hard to find, the ones i found, there are DDR 1GB 400Mhz which is the right one, BUT they have "Heat Spreader" can i use them to upgrade my iMac?
Cheers....

Hello Juan Bermudez,
While it is not explicitly stated that memory with heat-sinks will not fit, I do not believe that they will. The following document provides the specific requirements that your iMac G5 has with regards to memory.
About iMac G5 Memory
1. iMac G5 computers work with memory modules (DIMMs) that meet all of
     these criteria: PC3200, 2.5V, unbuffered, 8-byte, nonparity, 184-pin,
     400Mhz DDR SDRAM.
2. There are two RAM slots. The maximum amount of RAM you can install is 2
     GB. You can use RAM module sizes of 256 MB, 512 MB and 1 GB, in either
     slot.
3. DIMMs with any of the following features are not supported in the iMac G5
     computer: registers or buffers, PLLs, ECC, parity, or EDO RAM.
Memory, 17-inch Replacement Instructions
http://manuals.info.apple.com/MANUALS/0/MA501/en_US/imacG5_17inch_memory_.pdf
Cheers,
Allen

648 Max - Identifying but not using both RAM modules

Hi!
I'm totally new here, just stumbled across this forum while googling for a solution to my problem, so please excuse my lack of proper terminology if that should occur.
I have the following system (data obtained from Everest 2.20 and own brain):
P4 2,80 GHz, no OC, no HT
2x Crucial PC2700 DDR-DIMM 1024MB 2,5-3-3-7 @ 166 MHz
MSI 648Max (MS-6585)
PowerColor Radeon X1950Pro AGP 256MB GDDR3, no OC
Thermaltake Toughpower 850W Modular
Hitachi Deskstar T7K250 160GB IDE
BIOS (this is my weak spot...) Everest says BIOS type AMI, dated 28/1/2003, no info other than that
WinXP Home SP3 + all updates AFAIK
In general, the system is originally ready-built Fujitsu-Siemens system from 2002 (i think), but heavily modified by me (RAM upgrade, HDD upgrade, several GPU and PS upgrades).
My problem is that the computer only occasionally uses both RAMs (i.e. showing 2,00GB RAM in My Computer's properties). More often than not, however, it only shows 1,00GB RAM. AFAIK this problem is pretty recent, and did not occur when the RAM was new and installed by me. I have tried to systematically testing the two different RAM modules separately in each of the three DIMM slots, and the computer booted and ran Windows desktop at idle without problems in all configurations. I therefore dismissed the possibility of both MB and RAM failure, and reinstalled both modules in DIMM 1 & 2, where they have always been located. The computer ran with 2,00GB of RAM for a day, then reverted back to only 1,00GB the next morning. Tried moving the RAM in DIMM 2 to DIMM 3, and the computer ran another day on 2,00GB. However, this morning it was back to 1,00GB again.
Through all this, Everest 2.20 has always detected both RAMs in the correct slots, but have displayed 1024 and 2048MB memory on the System Summary page. Rebooting the computer without dismantling it and fiddling with the modules does apparently not change the usable amount of RAM back to 2,00GB when stuck at 1,00GB.
Anybody know what the issue might be (since none of the components seem to be faulty by themselves) and how to solve it? Please keep in mind that my BIOS skills are shoddy at best (but successfully flashed the BIOS once by help of an official guide, no stability issues after the upgrade), so detailed instructions regarding that might be a bit over my head. The same goes for overclocking or manually adjusting any voltages or freqs, which I've never tried.
Thanks in advance!
EDIT: Apparently a total power-off reboot (power down, PS power switch off, push and hold power button till lights go out, switch back on, power up) seems to reset the RAM to the correct amount of 2GB. Any clues?

The voltage to the memory might need to be raised one notch. That adjustment is done in the bios.
You can download the motherboard manual from this link. http://global.msi.com.tw/index.php?func=downloadfile&dno=3576&type=manual
Section 3 page 27 thru 28 cover the adjustment of the memory voltage.
This is for a retail motherboard. I do not know if your motherboard has this in its bios. It is in a section under Frequency/Voltage Control

RFC_ERROR_SYSTEM_FAILURE: The function module "DD_DTEL_GET" cannot be used.

Hi there,
I´m trying to launch NWCE 7.1 Webdynpro applications accessing ABAP function with no success.
The landscape consists of an SAP NWCE 7.1 EHP1 (Trial) and an SAP NW 2004s ABAP (Licensed). NW2004s is configured as Gateway and Message Server for the SLD. I can ping/test JCOs successfully and the SLD seems to work fine. RZ70 and SM59 show no errors in the "R3" side and both systems seem to be well-registered as Technical Systems.
I have done some simple examples in Developer Studio to ensure that the conection between both stacks is going well, but I have allways the same issue regardless using ARFC/ARFC2, new projects/old existing projects, etc.
When I test for first time the application, the following exception is thrown:
Caused by: com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE: The function module "DD_DTEL_GET" cannot be used for 'remote' calls.
     at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:456)
     at com.sap.mw.jco.MiddlewareJRfc$Client.execute(MiddlewareJRfc.java:1416)
     at com.sap.mw.jco.JCO$Client.execute(JCO.java:4168)
     at com.sap.mw.jco.JCO$Client.execute(JCO.java:3596)
     at com.sap.mdi.jco6.Destination.execute(Destination.java:29)
     ... 136 more
If I refresh the page the last exception disappears and a new one is thrown:
#2# local/prjWD_Acceso_ABAP/FlightListApp#java.lang.NullPointerException
     at com.sap.mdi.ddtypes.DDDataelement.getDescription(DDDataelement.java:305)
     at com.sap.dictionary.types.mdi.util.TextServices.getDescription(TextServices.java:165)
     at com.sap.dictionary.types.mdi.util.TextServices.getQuickInfo(TextServices.java:145)
     at com.sap.dictionary.runtime.DdDataType$TextService.getQuickInfo(DdDataType.java:220)
     at com.sap.tc.webdynpro.progmodel.context.DataAttributeInfo.getDisplayText(DataAttributeInfo.java:385)
     at com.sap.tc.webdynpro.progmodel.context.DataAttributeInfo.getDisplayText(DataAttributeInfo.java:355)
     at com.sap.tc.webdynpro.progmodel.context.MappedAttributeInfo.getDisplayText(MappedAttributeInfo.java:292)
     at com.sap.tc.webdynpro.progmodel.view.ViewElement._getText(ViewElement.java:818)
     at com.sap.tc.webdynpro.progmodel.view.UIElement.getTooltip(UIElement.java:515)
     at com.sap.tc.webdynpro.clientserver.uielib.standard.uradapter.InputFieldAdapter$OrdinaryField.getTooltip(InputFieldAdapter.java:8201)
     at com.sap.tc.webdynpro.clientserver.uielib.standard.uradapter.InputFieldAdapter$OrdinaryField.getParameter(InputFieldAdapter.java:7496)
     at com.sap.tc.ls.renderer.ie6.LSInputFieldRenderer.render(LSInputFieldRenderer.java:160)
     at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:152)
     at com.sap.tc.webdynpro.clientimpl.html.client.RenderManager.render(RenderManager.java:519)
     at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:130)
     at com.sap.tc.ls.renderer.ie6.LSColumnLayoutRenderer.renderColumnLayoutCellFragment(LSColumnLayoutRenderer.java:1882)
     at com.sap.tc.ls.renderer.ie6.LSColumnLayoutRenderer.renderColumnLayoutRowFragment(LSColumnLayoutRenderer.java:1715)
     at com.sap.tc.ls.renderer.ie6.LSColumnLayoutRenderer.renderColumnLayoutFragment(LSColumnLayoutRenderer.java:1600)
Then, editing the application in Dev. Studio, if I delete tables and/or single fields binded to model context, the last exception doesn´t appear any more but the application enter in the catch section executing the BAPI call:
     try
          wdContext.currentBapi_Flight_Getlist_InputElement().modelObject().execute();
     catch(Exception ex)
          wdComponentAPI.getMessageManager().reportException("Execute error."+ex.toString()+ex.getMessage());
          StackTraceElement errores[] = ex.getStackTrace();
          String errorSTR = new String();
          for (int i = 0; i < errores.length; i++){
               errorSTR += errores<i>.toString() + "
          wdComponentAPI.getMessageManager().reportException(errorSTR);
     wdComponentAPI.getMessageManager().reportSuccess("After catch.");
     // Resynchronise the data in the context with the data in the model
     wdContext.nodeOutput().invalidate();
The first two exception seem to be related each other, and it is true that FM "DD_DTEL_GET" is not RFC enabled in R3. Should it be RFC enabled?
As far as I know, one of the JCO conectors is used for retrieving metadata, that is, data related to types, lenghts, etc. The FM "DD_DTEL_GET" is used for that kind of operations and the second exception is related to that aswell (com.sap.mdi.ddtypes.DDDataelement.getDescription).
I don´t know what else should I test in order to launch an RFC function from WDJ and the trial version is about to expire!
Does anyone know about any oss note or any other tips related to this issue, please?
I am going to test the conectivity via Visual Composer and see whether it´s possible :S
Let me know if you need anymore info about the situation.
Thanks a lot!

Hi again,
The issue hasn´t been solved yet :(.
After applying Note 1244067 the function module has the RFC flag checked but the Null Pointer exception are still there.
java.lang.NullPointerException
at com.sap.mdi.ddtypes.DDDataelement.getReptext(DDDataelement.java:166)
at com.sap.dictionary.types.mdi.util.TextServices.getColumnLabel(TextServices.java:115)
at com.sap.dictionary.runtime.DdDataType$TextService.getColumnLabel(DdDataType.java:212)
at com.sap.tc.webdynpro.progmodel.context.DataAttributeInfo.getDisplayText(DataAttributeInfo.java:379)
at com.sap.tc.webdynpro.progmodel.context.DataAttributeInfo.getDisplayText(DataAttributeInfo.java:355)
at com.sap.tc.webdynpro.progmodel.view.ViewElement._getText(ViewElement.java:818)
at com.sap.tc.webdynpro.clientserver.uielib.standard.impl.Caption.getText(Caption.java:369)
at com.sap.tc.webdynpro.clientserver.uielib.standard.uradapter.TableAdapter$HeaderCell.getHeaderText(TableAdapter.java:11441)
at com.sap.tc.webdynpro.clientserver.uielib.standard.uradapter.TableAdapter$HeaderCell.getParameter(TableAdapter.java:11043)
at com.sap.tc.ls.renderer.ie6.LSSapTableHeaderCellRenderer.renderSapTableHeaderCellFragment_iteration(LSSapTableHeaderCellRenderer.java:2421)
at com.sap.tc.ls.renderer.ie6.LSSapTableRowRenderer.renderSapTableRowFragment(LSSapTableRowRenderer.java:223)
at com.sap.tc.ls.renderer.ie6.LSSapTableRowRenderer.render(LSSapTableRowRenderer.java:122)
at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:152)
at com.sap.tc.webdynpro.clientimpl.html.client.RenderManager.render(RenderManager.java:519)
at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:130)
at com.sap.tc.ls.renderer.ie6.LSSapTableDefaultBodyRenderer.renderSapTableDefaultBodyFragment(LSSapTableDefaultBodyRenderer.java:301)
at com.sap.tc.ls.renderer.ie6.LSSapTableDefaultBodyRenderer.render(LSSapTableDefaultBodyRenderer.java:119)
at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:152)
at com.sap.tc.webdynpro.clientimpl.html.client.RenderManager.render(RenderManager.java:519)
at com.sap.tc.webdynpro.clientimpl.html.renderer.lightspeed.base.LSRenderManager.render(LSRenderManager.java:130)
Language resources data in the webdynpro are: Current locale = "es", Default VM locale = "es_ES". The backend default language is "EN". Could this be a problem in order to retrieve descriptions or any other language dependent data?
Thank you
Vicente.

FYI to all: Creative Cloud users cannot readily use BC Blog module.

FYI for anyone who has been as confused as I have watching these videos on the adobekb.com site and tv.adobe.com about using the BC CMS Blogging modules....
Creative Cloud users cannot readily use this feature that is discussed. We would have to pay an additional BC monthly charge in order to have the Blog module and other nifty stuff.
If there is an Adobe staff member around, it would be nice to know if there are any plans to change this in the future considering we're already paying monthly for the Creative Cloud.
Also, can you please point out somewhere in your tutorial videos that users will need to purchase the BC upgrade in order to take advantage of the blog module? It's unfortunate that this wasn't more readily apparent to me. I spent quite a bit of time trying to follow the monkeybar tutorial only to realize that the reason my BC interface looked nothing like the one shown in the video was because I didn't have the same BC package.
For now I'll go the tumblr route I guess - since there doesn't seem to be another efficient option.
Thanks!
Best,
Kelly Burr.

I agree, it is disappointing to find out there's an additional charge on top of the Creative Cloud membership. There should be some access

Satelite T130 cannot restart (reboot)

I have Satelite T130-10G PST3AE bios v2.7 and it cannot restart.
After restart the screen blanks the fan makes becames noisy for short time and that is all.
To start it again it is necessary to switch it off and on. It starts normaly.
Restarts were attempted from Win7, Fedora Linux, Bios setup (when saved), ctrl-alt-del before operating system start (boot menu). The result was always as was described.
Thank you for any hint.

I think it is hardware related issue since this issue seems to appear using all the different systems (windows, linux)
But did you already try the new OS installation? If not do that!
Back to the idea where the hardware could malfunction:
In my opinion firstly the RAM modules should be tested and checked. Since the RAM modules could cause such or similar issues, I think this is a good idea to check this part.
The best would be the usage of new, good tested modules.
But if motherboard is affected, the new modules would not be helpful very much :(

Help with 655 Max and Possible Memory Problems...

Just recieved my 655 Max and have put my system together, but when I turn it on it makes a constant beeping sound. I tried taking out both memory sticks, lol, and turning it on and the sound stops, I tried putting in one memory stick and the sound starts again.
I suppose this is a memory problem.
by the way I am using Corssair 256mb CMX256a-3200C2 memory.

[The alarm that you are getting is the CPU Fan Alarm you will have to diable it in the Bios. I am using a Vantec Aeroflow heatsink and my CPU alarm also is constantly on and was very annoying till I disabled it. My system still doesn't boot to XP yet as I have RMA'd bothe the MB and Ram. QUOTE]Originally posted by TritonB7
Hey Kaiguy the comp does continue to make sounds till I shut the system off. And I'm not sure how a standard pc tone sound would sound like, :(. But it does make beep followed by a lower pitched beep, and it repeats this till I shutdown the system.
(1) I cannot Access Bios.
(2) I have two sticks of Corsair 256mb CMX256a-3200C2 memory. I do not have any other ram available that will be compatible with this motherboard. Ive tried using one stick at a time in each of the slots. No Luck.
I highly think that both sticks not working is very unreal.
(3) and reseting bios by the jumper isnt working either.
I can probably try buying some diffrent memory, or returning the whole mobo and exchanging it for the same one.
By the way on my monitor when i turn the comp on it says 8x Extreme or something close to it while the comp is beeping. I doubt that, that has anything to do with it. This is my first MSI board :( , I've always been an Asus person but Im still open for MSI i'm sure I just recieved a faulty board.
[/QUOTE]

How to extract data by using function module in generic extraction please

how to extract data by using function module in generic extraction please give me steps required

Dear Deba,
Generic Extraction via Function Module
/people/siegfried.szameitat/blog/2005/09/29/generic-extraction-via-function-module
If the requirement is like extracting data from multiple tables with some complex logic then views cannot be used..so u cna go for FM is used where it can be achieved.
Chk these
/people/siegfried.szameitat/blog/2005/09/29/generic-extraction-via-function-module
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a0f46157-e1c4-2910-27aa-e3f4a9c8df33
check the following thread
generic extraction with function module
Generic Extraction with function module
Regards,
Ram.

Intel iMac continuous crashes - cannot restart

Computer has been running fine for the last 3 years (it has bootcamp running Windows).
Have not had a problem before with crashes. Was using it all day today, then a grey colour came down my screen and a message told me to +restart my computer. hold down the restart key.+
I did this and the computer restarted with an errorlog that i could send to apple - i did this and it worked fine for 10 minutes, then the same thing happened.
I kept restarting and sending the errorlogs to apple - and the crashes have kept happening. I have notcied that my Entourage application is now also unexpectadly closing down.
Now after about the 10th restart it just will not start at all - it comes up wiht a black screen and the error log appears on that.
*Here is a copy of one of the many error logs I receive:*
panic(cpu 1 caller 0x001A49CB): Unresolved kernel trap (CPU 1, Type 14=page fault), registers:
CR0: 0x8001003b, CR2: 0x00000000, CR3: 0x00ecd000, CR4: 0x000006e0
EAX: 0x3b9aca00, EBX: 0x00000000, ECX: 0x00000000, EDX: 0x00000000
CR2: 0x00000000, EBP: 0x2526bec8, ESI: 0x037a5e92, EDI: 0x00000000
EFL: 0x00010206, EIP: 0x0032cd79, CS: 0x00000008, DS: 0xe13b0010
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x2526bcf8 : 0x128d0d (0x3cc65c 0x2526bd1c 0x131f95 0x0)
0x2526bd38 : 0x1a49cb (0x3d2a94 0x1 0xe 0x3d22b8)
0x2526be48 : 0x19b3a4 (0x2526be58 0x2526be68 0xe 0x190048)
0x2526bec8 : 0x2ba5cc (0x2ba5d4 0x0 0x1 0x13546b)
0x2526bf58 : 0x2ba5fa (0x0 0x1 0x2526bf78 0x19e23a)
0x2526bf78 : 0x13d989 (0x0 0x0 0x0 0x0)
0x2526bfc8 : 0x19b21c (0x0 0x0 0x19e0b5 0x407ea10) Backtrace terminated-invalid frame pointer 0x0
Kernel version:
Darwin Kernel Version 8.11.1: Wed Oct 10 18:23:28 PDT 2007; root:xnu-792.25.20~1/RELEASE_I386
Model: iMac4,1, BootROM IM41.0055.B08, 2 processors, Intel Core Duo, 2 GHz, 2 GB
Graphics: ATI Radeon X1600, ATY,RadeonX1600, PCIe, 128 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 667 MHz
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 667 MHz
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x89), Broadcom BCM43xx 1.0 (4.170.46.9)
Bluetooth: Version 1.9.5f4, 2 service, 0 devices, 1 incoming serial ports
Network Service: Built-in Ethernet, Ethernet, en0
Serial ATA Device: Maxtor 6L250M0, 233.76 GB
Parallel ATA Device: PIONEER DVD-RW DVR-K05
USB Device: Built-in iSight, Micron, Up to 480 Mb/sec, 500 mA
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Mitsumi Electric, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mA
USB Device: Bluetooth USB Host Controller, Apple, Inc., Up to 12 Mb/sec, 500 mA
USB Device: IR Receiver, Apple Computer, Inc., Up to 12 Mb/sec, 500 mA
If anyone knows a solution I would be most grateful - I need ot get this sorted asap.

Try following this procedure to reset SMC
http://support.apple.com/kb/HT1543
which is basically disconnecting all cables and power, and reconnecting following a precise procedure. If you are connecting into a crowded or old power strip (surge suppressor), try connecting it directly to the wall outlet, at least initially (as a test). Power it up with nothing connected, except for the power cord. If that works properly, connect just your keyboard/mouse and use it that way for a while, to make sure it continues to work properly.
If the same issue occurs, even with nothing connected, you'll have to look at other causes.
To see if it might be software, insert your Mac OS X installation disc and restart with C key held down to start up from the optical drive. Does it get to the Installer screen without crashing? If so, it may indicate some problem with your currently installed system.
If it still crashes, one thing you can try is removing your RAM modules and reinserting them into their slots. While you are looking at the bottom edge of the iMac, wipe off the dust on the air intake vents; I added some RAM recently, and I was amazed at how much dust there was on those vents, blocking airflow.

Msi 655 max fisr ht ready: does it have fsb800 support?

i own msi 655 max fisr mobo, that supports ddr333 and fsb 533 as msi says. but it can handle also ddr 400 through overclocking and the bios has an option for fsb selection up to 250 mhz. according to me, this meens that one can use a cpu at fsb 800 by overclocking the mobo from the bios, even if it doesn't support the microcode of the cpu. does anyone have tested this statement, as at the time it is onlu speculation by me, as it is too expensive for my to buy new cpu and try it.
moreover, my revision of the mobo is stepping b0, thus it supports ht cpus and if it proves to support fsb 800 by overclocking, then i can keep it for a while, upgrading my system only with new cpu. i'll be thankful if anyone can provide me with some information on this topick.

What I am trying to explain is the downclocking of a DDR 400 RAM 1st to 333 Mhz then try to o/c to get DDR 400 or above, not saying that you are wrong.
Any board can support o/c'ing but it is all up to whether the hardwares that you have and their capability to do so as no one can actually determined whether or not the hardwares that you have will definately let you ends up the way it's really meant to be as there's always important facts being left out so it's always trial and error...
I have 2 of these systems running on the same mobo, but the highest I can reached with DDR 400 RAMs are just near DDR 400 not exactly 400 MHz and FSB are at near 170 quad = 170 x 4 = 680FSB... from a FSB 533 CPU. Both have different results as 1 is with DDR 333 RAMs o/c'ed to 380MHz on 2.8 B CPU and another with DDR 400MHz down to 333MHz then o/c'ed up to near 400Mhz on 2.8B CPU also...

655 MAX HT_SERIAL ATA PROBLEM (GHOSTLY WERID)

Ok.. I never thought there could be ghosts in a machine until now.
I have a 655 MAX HT MB.
The only Drive I have is a Seagate Baracuta 120 Serial ATA.
At work when I plug in the computer everything works fine.. The Promise SATA controller finds the ARRAY and I boot to Windows like a good boy.
Now, When I take my computer home to use. I turn on the machine and Wala.. No Array is found in the promise controller. I then go into the setup for Array (scratching my head) where you can see the drive. So I try to Define a new array, but for some weird reason It will not write the Array and Says Error has accured and it will restart.
So I give up and reseat everything trying new SATA cables the works. I used to do Tech suport back in my younger days so I am very framiliar with what I am doing so I thought.
Here I am at work bringing in my computer to the Tech. He plugs it in Powers the machine up and everything works fine.
So at home I did try multiple power outlets and with a UPC and without one as well. If anyone knows what might be causing the Array not to show up at my home please let me know. I am really boggled by this problem.
Thanks
Count

Hello
We are MSI distibutors in Portugal and I have the same problem, I already test every MB and the problem persists.
If you connect te PS2 mouse everything work's fine....
But if put enable in the bios the USB Legacy Support everything work's !! :D
Best Regards
Paulo Gouveia
Technical Manager
MSI Distributor
http://www.jpsacouto.pt

655 max overclock

can someone tell me the maximum of 655 max can overclock?

Okay, after *extensive* testing, I think I've figured out what the problem is. If I put a DIMM in banks 1 or 2 (or both) it won't POST. I can fill banks 3 and 4 and it works perfectly, though not in dual channel mode.
It doesn't matter what RAM I put in and this wasn't obvious at first. I was simply trying to t-shoot by using a single stick in bank 1.
While I can live, for now, with only 2 banks filled, this isn't the advertised product I purchased two months ago. I sent in an RMA request yesterday. How dependable is the RMA process at MSI? How long does it normally take?

655 max 6730 crashing specialist comp

i have a 655 max msi 8xtreme 6730 version 1.0 mother board with a 2.4 northwood p4 512 ram i have tried the basic config with nothing more than the board and a video card ranging from radeon 7000 gefrce 4 and now geforce fx 5200 and othe hard ware like sound blaster live 5.1 various ether net or lan cards and various didgital cameras and nothing works on this hunk of useless worthless equipment the only reason why this thing exist is to bring out the inner anger from deep in my spirit from just crashing with no message to mem dumps X( ;( ?( :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O please e-mail me @ [email protected]

I have a MSI 655 MAX-L (BIOS= A6730SMS V3.0 02252003) and a
Club3D 9800Pro 128Mb VGA card (BK-ATI VER008.004.008.018)
I had the problem that when WinXP Pro SP1 was started, it
freezes or black screen (Monitor led burning orange instead
of green) and i have to reboot with reset button.
Also sometimes it went back into VGA mode and i had to reboot WinXP.
WinXP log file says:
Source: ati2mtag
Discription:
The driver ati2dvag for the display device DeviceVideo0 got stuck in an infinite loop. This usually indicates a problem with the device itself or with the
device driver programming the hardware incorrectly. Please check with your hardware device vendor for any driver updates.
The solution for me is: Disable Fast Write is the BIOS and
in WinXP and put AGP to 4x instead of 8x in WinXP
Now i got 5723 points in 3DMark 2003 and no problems
You can find these options in WinXP: Display Properties ->
Settings -> Advanced -> SMARTGARD
I use: WinXP PRO SP1, Radion v3.04 drivers, SiS IDE v2.03, SiS AGP v1.16a,
Try this solution, maybe it will help
Greetz
thedude
ps: i still like to have a solution to put agp back to 8x and enable fast write

Cannot restart using 4 RAM Modules on 655 Max HT Ready (MS-6730)

Similar Messages

Maybe you are looking for