Cannot see Mac Mini Server from Internet: DynDNS alias gets thru cable modem to wireless router, not to the Mac Mini. How to configure?
I want to make my Mac Mini Server (Lion) visible to the Internet from my home LAN. I have followed the Lion server install wizards and also set up a dynamic DNS at DynDNS.com.
When I enter the Internet address with the proper alias from a web browser, I get dumped into the admin screen of the Linksys wireless router WRT300N. Hint: the WRT300N provides DHCP for the LAN, not the cable modem providing DHCP. The WRT300N has DDNS service set up. NAT and RIP are disabled. The Mac Mini DHCP is reserved.
Suggestions? I could use the Motorola Surfboard SB6121 to provide DHCP but have hesitations.
Point me to the right discussion/article and get me back on track, please.
This sounds like a simple port forwarding issue, but I don't understand your LAN setup.
The WRT300N has DDNS service set up. NAT and RIP are disabled.
The chances are, you're running NAT somewhere in your network. If not the WRT then what? If it's your cable modem then you must have port forwarding configured on the cable modem, and that's where you need to focus - change the port forwarding to point to your Mac Mini's address rather than the WRT.
HOWEVER, it is far more common to have the wireless router perform NAT and DHCP, which is why I question your setup.
Not directly related, but:
The Mac Mini DHCP is reserved
Nix this. Your server should be configured manually, with a static IP address, not DHCP, even with a reservation in the DHCP server. The only advantage of DHCP is for dynamic hosts (hence the 'D' in 'DHCP') or if you expect to change your entire local subnet on any kind of frequent basis. The reality is that you can't just change the IP address of Mac OS X Server like this - there are too many dependencies, so it's better to set it manually, knowing that there's a cost (and pain) to change the server's address.
Similar Messages
-
I cannot see skin of flashhelp in Internet explorer 7
I cannot see skin of flashhelp in Internet explorer 7
I ran into this problem too. The coding for RoboHelp X5 must
have have at minumum IE 5 and javascript 1.2 running on the server
you are viewing your project from. I did come up with a work around
and it is listed in this forum. IE 7 is XML based and X5 is
javascript based. Something to think about. -
Can't connect to server from internet
Hi
I’ve just set up a new Mac mini server with Lion 10.7.1.
It’s configured as "Host name for Internet".
I can reach the router from Internet. NAT on the router is setup to forward the the required ports according to Apple’s document "Well known TCP and UDP ports used by Apple software products"
Still I can’t connect to any service on the server from Internet (Address Book, Calendar, AFP, VPN)
Please help!
AsbjørnYou can test it from outside with a telnet connection:
Open Terminal.app (Applications > Utilities) and insert:
telnet <ip-address-from-router> <port>
so testing the iCal port would be:
telnet 123.234.45.6 8008
or SSL:
telnet 123.234.45.6 8443
When you get "Escape character is '^]'." the connection is established to the server/port.
When you get " telnet: connect to address 123.234.45.6: Connection refused | telnet: Unable to connect to remote host" something is wrong with the setup.
Maybe it's the Port-forwarding, maybe the setup of the server.
Is it working in the local network?
I also would recommend you, to NOT share AFP over the network! The traffic isn't secured in a single way! Instead just configure VPN and establish the AFP connection through that VPN tunnel, but not directly by opening that connection to the internet! -
Cannot see EMC PowerPath devices from ASM instance on Solaris 10 x86
Hello,
I'm trying to use EMC PowerPath devices as ASM disks, but cannot see any usable disk
from the ASM instance.
My configuration:
Hardware: Sun X4600M2
Solaris 10 8/07 x86_64
EMC PowerPath 5.0.2_b030
Oracle 10.2.0.1.0
The PP devices are /dev/rdsk/emcpower* which are softlinks to the correpsonding /devices/pseudo/emcp*.
Since I know that these devices must have suitable permissions, I've set ownership and
permission of e.g. /devices/pseudo/emcp@1:a,raw to oracle:dba and 660. The ASM instance's
init.ora file has *.asm_diskstring='/dev/rdsk/emcpower*', so I assume it will scan all
/dev/rdsk/emcpower* softlinks and fetch the ones with sufficient permissions. But nonetheless
a 'select count(*) from v$asm_disk' gives me 0, i.e. nothing.
I've just read some recommendations of using slice 6 of the disk with partition type 'usr', but
this seems to me quite superficial. I would like to use simply slice (=partition) 0 starting from
cylinder 1.
I would be very glad for any solution.
Best regards
UdoProblem solved.
After some tests with plain files instead of devices via undocumented parameter
asmallow_only_raw_disks=false in order to check ASM functionality,
I've finally created new node devices only for oracle (and set_asm_allow... back to true).
original EMC PowerPath pseudo devices (e.g.):
-bash-3.00$ ls -l /devices/pseudo/emcp@13:a,raw
crw------- 1 root sys 215, 832 Dec 10 15:29 /devices/pseudo/emcp@13:a,raw
corresponding new character device with proper ownership and permissions:
-bash-3.00$ ls -l /u01/app/ora-dev/raw/emcp13a
crw-rw---- 1 oracle dba 215, 832 Dec 10 14:56 /u01/app/ora-dev/raw/emcp13a
With *.asm_diskstring='/u01/app/ora-dev/raw/emcp*' in ASM-instance's init.ora,
I was able to see the devices via select * from v$asm_disk and could create the
ASM diskgroups.
Regards
Udo -
Cannot see data in BSO from transparent ASO partition
I have 2 cubes: BSO (target) and ASO (source).
BSO should show data from ASO corresponding element "Fact" from dimension "Scenario".
I can see the data using ASO directly, but I cannot see data viewing it from BSO using transparent partition...Hi,
When you have the data in the ASO( i.e source cube) ,it should reflect in the BSO ( i.e destination) . I am sure there is problem with the transparent partition ,you had created .Validate and share more info of error ( if you encounter during partition creatino) , that should be resourceful
Sandeep Reddy Enti
HCC -
I purchased Lightroom from B&H Photo a few months ago. I did not instal the software, because I was purchasing a new computer in the near future. I am now purchasing that computer, but cannot find the software. B&H suggested that I contact you directly to help me. I have the receipt, and you can look to see that the program was never used. It would be great if you could just send me another copy of the software. Thank you very much.
MarcDownload from Adobe's website
Win: Adobe - Lightroom : For Windows
Mac: Adobe - Lightroom : For Macintosh
Install then enter your serial number when prompted.
I have the receipt, and you can look to see that the program was never used.
The receipt is only of use to B&H. Adobe will have no record of it.
If you quote an Adobe Lightroom serial number then Adobe can confirm if that serial number has ever been registered. That step should not be required at this stage though. Just install the software. -
I have iPhone 6, 8.3. I cannot use bluetooth at all from my device, even to connect my macbook pro. I did all the recommended trouble shooting such as reboot and reset network settings. but it does not recognise any bluetooth device. Pls help.Thank you.
See iPhone BT profile on what can be connected/paired:
iOS: Supported Bluetooth profiles - Apple Support
And BT troubleshooting:
iOS: Troubleshooting Bluetooth connections - Apple Support -
ICloud notified me my iPhone was offline. I cannot see a map, or send a tone. Should I be able to do these even though the device is offline?
Thanks for any help?If you think getting your web pages to appear OK in all the major browsers is tricky then dealing with email clients is way worse. There are so many of them.
If you want to bulk email yourself, there are apps for it and their templates will work in most cases...
http://www.iwebformusicians.com/Website-Email-Marketing/EBlast.html
This one will create the form, database and send out the emails...
http://www.iwebformusicians.com/Website-Email-Marketing/MailShoot.html
The alternative is to use a marketing service if your business can justify the cost. Their templates are tested in all the common email clients...
http://www.iwebformusicians.com/Website-Email-Marketing/Email-Marketing-Service. html
"I may receive some form of compensation, financial or otherwise, from my recommendation or link." -
This past month I have been having problems connecting to my home wireless connection. I have a MacBook Pro OSX Version 10.6.8. Previously I had no problems whatsoever. I have tried unplugging the wireless router, turning off the wirless airport, deleting the network name from my list of servers and trying to reconnect this way. These methods have worked temporarily, but the same problem keeps coming back. Most of the time my personal wireless connection does not even come up among the list of available networks. My fellow flatmates have PCs and both of them are able to connect to the network without problem.
The router is a d-link model DIR-615. I am not tech savy, so if any other information need to be provided in order to better understand my situation, please let me know.
Please help me!If I open the list of networks in a window it says "connection timeout," but if I just select it from the drop down it tries for awhile and then stops with no prompt. When I try to run network diagnostics it says "sorry, we can't connect to the internet" (or some solution-free variation of that)
-
when i follow the steps it does it but when it gets to itunes it says 'iTunes could not contact the iPhone software update server because you are not connected to the internet' but i am connected to the internet ..?
Were you definitely connected to the internet at the time? If you don't have iOS 5 on your iPhone then the only way to update it would be via iTunes, once updated to the latest version of iOS you'll be able to update your iPhone without connecting to iTunes "over-the-air".
Before updating however it goes without saying to Backup your iPhone, this should happen by default upon connecting your iPhone to iTunes.
Regards,
Steve -
Switched from DSL to CABLE. WRT54G Wireless Router stopped working.
When I switched from DSL to CABLE, my WRT54G Wireless Router stopped working. I am not able to access the router page (192.168.1.1) Also, when I use the set up CD for re-installation, the wizard aborts in the middle saying it can not connect.
I appreciate any help to resolve this problem.
P.S. The router acts like a one-port wired router.Here is my favorite method for resetting a router to factory defaults, and trying to get it working again.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you. -
HI,
When I upload photos from my Canon Rebel 1000D to iphoto the images are labelled JPEG, yet I shoot in RAW.How do I get iphoto 11 vers9.1.3 to not convert the photos to jpeg. I seem to have tried and read so much but just can't figure it out. How do I get iphoto 11 vers9.1.3 to not convert the photos to jpeg. Or do a have to use a different system? I have Adobe Bridge. Or can I upload directly into photoshop?
Also how do you install dmg's properly I am having problems installing them?
I have a Mac OS X 13 inch Version 10.6.7
Advice desperately needed
Thanks
NlouisDo you have Aperture installed? I found your model on a compatibility list; however, there was a note that it requires Aperture 2 to be installed:
http://www.apple.com/aperture/specs/raw.html
According to this excerpt:
To see a list of digital cameras with RAW-format support that are compatible with iPhoto, visit this Aperture webpage (any camera compatible with Aperture, Apple’s advanced photo editing and management program, is compatible with iPhoto as well)
which is at the bottom of this page:
http://docs.info.apple.com/article.html?path=iPhoto/9.0/en/pht41627265.html
I may be wrong, but I interpret that info to mean you need Aperture 2 before iPhoto will work with RAW? -
I have playlists on my original iPod but are not in the library. How can I move them from the iPod to the library?
She can choose to either enable the setting on her iPod to Manually manage music and videos. With setting enabled she can sync content to her iPod from multiple computers without it affecting whats already stored her iPod. For more information on syncing content to an iPod manually see this article.
http://support.apple.com/kb/ht1535
However, I would recommend copying whats on her iPod to her iTunes library first. There are several ways to accomplish this. See this older post from another forum member Zevoneer discussing the different ways to do it.
https://discussions.apple.com/thread/2452022?start=0&tstart=0
B-rock -
HOW CAN I TRANSFER PHOTOS FROM MY IPOD TOUCH TO MY PC BUT THESE PHOTOS ARE NOT IN THE SAVED POTHOS FOLDER. THEY ARE IN SEPARATE AND DIFFERENT FOLDERS THAT MY DAUGTHER SAVED FROM HER PC. IS THERE ANY FREE WAY TO DO IT. PLEASE REPLY TO JUMACAVA07@HOTMAIL.
THANKSIf you need to Transfer photos from iPod to PC,I have a method for your reference,I suggest you use iStonsoft iPod to Mac Transfer software to copy photos from iPod to Mac,a professional software,Not only can you quickly Copy pictures from iPod to Computer,but also can save a lot of trouble and time
[B]Follow these steps to Transfer photos from iPod to Mac[/B]
Step 1. Download and run the iStonsoft iPod to Mac Transfer software on your Mac computer
Step 2. Connect iPhone with Mac
Step 3. Hit "Photos" to scan photos from iPod to Mac
Step 4. Click "Photos" button to transfer photos from iPod to Mac
Step 5. Wait a while,you will success Transfer these photos from iPod to Mac
How to Transfer/Copy Photos/Pictures from iPod to Mac computer -
I buy for mac app but not for the iPad, so how do I reinstall a program that has already purchased? I need help because I bought the imovie'11 but when he opened it only brought 8 movie trailer templates instead of the 15 it says on the program. How do I solve this problem? Once paid for a program incomplete. I also liked that the AppStore itself had a button to reinstall programs already bought, because it is very hard to understand how to do this in the store, only option is to install and hide purchase, and how do I reinstall, attention'm talking about reinstalling a computer mac, not an ipad or iphone.
Thank you.Prodesigntools.com , go ahead and download the software from there and use your serial number to serialize it.
Maybe you are looking for
-
Hello! I am facing with the problem that a PSE file (tcode STRUST) on my SAP NetWeaver system is out of date. I deleted this PSE file. Now when I log in onto SAP system the warning/error comes up. Question: What are the technical steps to solve this
-
In house production time in material master .
Dear All , What will happen if i do not enter ( keep blank ) the inhouse production time in MRP 2 view ? Where i am using routing for all inhouse produced material . all the scheduling parameter are correct as per routing considered . i have checked
-
I am trying to create a BP(Organization) and assign a Sales Area for the BP in the Role Sold to Party. But when I try to assign a Sales Area to the BP through the Button 'Choose Sales Area' But the Button is in Display Mode and not in Change mode and
-
Unable to connect to WMI on remote machine
I get this error in my CCM.log after trying to install on a client server 2003 sp2. ---> Connected to administrative share on machine LCAPP22.lc100.net using account 'lcdom100\XXXXXX' SMS_CLIENT_CONFIG_MANAGER 11/26/2007 1:43:01 PM 7856 (0x1EB0) --->
-
HP Envy error C00D11BA appears after installing Microsoft Word. No audio due to config conflict.
I was installing the newest version of Microsoft Office Home & Student 2013 and noticed that the tutorial had no audio. After installation was complete, I had no audio at all on my new HP Envy laptop, whereas I had no problems beforehand. I get this