Cannot see my Airport Express

I have two AirportExpress and one TimeCapsule. I can see all three using a PC AirPort Utility. However, from a MAC AirPort Utility I can see only one at the time (I can see only the one I am connected to wirelessly). All three devices are connected to the same ethernet network with cables. How do I get the MAC to see all three device simultaneously?

I just did. Now I cannot neither the AirPort Express nor the TimeCapsule that I am connected to. However, I can still see all three devices on the PC.

Similar Messages

Airport Extreme works fine. Cannot see two Airport express units

Hello. I just bought a new Airport Extreme and 2 Airport express units to replace my old linksys routers and to take advantage of my new MacBook Pro and iTV units. I am a Mac newbie after 20 years of PC's. The Netgear DGND3300 DSL modem feeds DSL signal to the Airport Extreme unit and it works well with good internet and signal. I am trying to use the 2 Airport Express units to extend the signal around the house. The Airport Utility has seen both of them but then they disappear and it cant find them again. They are 10 feet away for now until I get them configured. How do I get them to connect and how do I configure them to extend the wifi range?
Thank you.

The first thing to check is your AirPort Extreme.
Open AirPort Utility - click Manual Setup
Click the Wireless tab/label below the row of icons
Make sure there is a check mark next to "Allow this network to be extended"
Update to save changes
You may have already done this, but it was not mentioned in your post and is a critical step to "extend" the network.
"Hard Reset" each of the AirPort Express devices by holding in the reset button for 10-12 seconds. Then power down one device and configure one at a time.
Open AirPort Utility - Click Manual Setup
Click the Base Station tab/label below the icons
Enter a name for the device, device password and adjust Time Zone settings
Click the Wireless tab
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the AirPort Extreme wireless network
Check mark next to Allow Wireless Clients
Wireless Security = Same security setting as the AirPort Extreme network
Wireless Password = Same password as the AirPort Extreme network
Confirm Password
Update to save settings. Close AirPort Utility immediately as soon as you see the message that the settings have been stored. You should have a green light on the Express in 40-45 seconds.
Now, log back on to the wireless network provided by the AirPort Extreme and you should see the AirPort Express that you just configured, if you are using a Mac. The Windows Firewall or anti-virus software may block the connection if you are using a PC. (The AirPort Express "disappears" as soon as you click Update in AirPort Utility because it has joined another network...that's why you don't see it. It uses a "temporary" network with a name like Apple Network xxxxxs during the configuration only).
Configure the second AirPort Express the same as the first. You will probably want to assign a different device name to that Express to keep things straight.
To "extend" effectively, the Express should be located approximately 1/2 the distance between the AirPort Extreme and the area that needs more wireless coverage. Depending on obstructions, you may need to alter this distance a bit.
The "extend" setup works like the hub and spokes of a wheel. The AirPort Extreme is the "hub" and each Express resides at the end of a "spoke". Each Express communicates directly to the "hub", not to another Express at the end of another spoke. For that reason, you cannot "extend" a device that is already configured to "extend".
Message was edited by: Bob Timmons

PC cannot see wireless Airport Express using Ethernet on D-LINK DIR-655 Router

This seems to be a recurring issue going way back, but I have yet to see a real solution posted.
I am using my Airport Express (APX) to stream music from the computers on my network to my stereo via Airplay. I have APX set up to wirelessly join my existing wireless network, which uses a D-Link DIR-655 router hooked to a Time Warner cable modem. I can succesfully connect all of my wireless devices via Airplay, through iTunes to my APX, including two laptops and an iPhone. However, my primary desktop PC, which does not have a wireless card is linked directly via ethernet cable to my D-Link router, and it is not able to see my APX. I can, however, see the Airport Express from my PC through my Airport Utility by directly typing in the IP address. Note that the APX set-up option to allow Ethernet clients is checked. I also noticed that my laptops will stop detecting the APX if I directly connect them to my D-Link router via Ethernet and turn off their wireless cards. They will resume detecting APX when I turn their wireless connections back on. So, bottom line, I am convinced that this is not a firewall problem. Although I have tried every conceivable setting of my D-Link router and APX, I am convinced it is either a wireless to ethernet communication issue, or some obscure setting on APX.. Any help would be appreciated.
Thanks,
Wayne

I think I found the fix based on reading some Apple TV forums where several people were having the same problem. Under Advanced Network settings in the D-Link setup, I just checked "Enable Multicast Streams" and that seemed to do the trick.

Itunes can't see my Airport Express speakers after I close my laptop

So this is a weird issue- and I haven't been able to find a prior discussion on this topic. Apologize in advance if I asking something that is already well documented.
but I've seen the problem on two separate laptops now: if I stream my itunes through my airport express speakers and then subsequently close my laptop (presumably putting it into hibernate or some other energy saving mode), itunes cannot see the airport speakers upon reopening the laptop. I have to reset Itunes - and then it will see these speakers every time. Same thing happens when I reset my airport express- sometimes I have to reconfig the router through the airport utility. As soon as a press update and the router resets... then itunes cannot see the airport express speakers.
Not a huge issue- just requires a lot of rebooting to fix. Buts its frustrating.. my macbook speakers are lame. I wish itunes has some sort of speaker refresh button that would reset the speaker settings.
My wife says it is known itunes bug.. anyone know anything on this?
Thanks in advance everyone!!

1. Did you try just to switch back to the cpu-speaker and the directly back to the express?
2. Did you do a firmware update of your express? Just open the express-server-program to do so.

Itune on iMac cannot connect to Airport Express, but Itune on XP can

Hello
I've the following situation:
Itune cannot see the Airport Express unless my Iphone Remote controle is connected to Itune. And eventhough, Itune fails to connect to it.
Here is the environment of my network
1) third party LAN/Wireless router (connected to the internet)
2) iMac (10.4.11) connected via the LAN port to the router
3) Airport Express (7.3.2) connected to the wireless network
4) one Iphone connected to the wireless network
5) one XP computer connected to the wireless network
6) All devices are in the same subnet
What really puzzle me is that Itune on the XP laptop can broadcast music to the Airport Express without any issue. But Itune on the Mac does not see at all the Airport Express unless I connect my Iphone to Itune. When I do so, the Airport Express become listed in the status bar of Itune. But if I try to make Itune connect to it, it try for a while then it stop trying without any error message.
I really don't understand what is going on. Does any body can give my a bit more information how Itune and Airport Express communicate? Or have any idea where I should direct my troubleshooting?
Thanks in advance for any help

So did i screw something up last night when i connected using my PC?
That sounds likely. Maybe the security type or password?
And if so how do i re-set the link with my mac??
Try the options described on pp. 30-33 of http://manuals.info.apple.com/enUS/AirPort_Express_SetupGuide.pdf
Once you get things working again, suggest you save the settings in a profile. In future when you bring the PC home, create a different profile for experimentation. Switch back to the usual profile when you're done with the PC. Eventually, you should be able to develop one profile that works with both machines.

My Airport Utility doesn't see my Airport Express??

My Airport Utility doesn't see my Airport Express. . .so I cannot run iTunes. . it used to work fine. .

Version of utility, and express? Makes a huge difference.

Airport utility cannot find my Airport Express, repeated rescans, nothing, even with direct connect via Ethernet. Help!

I use Airport Express to stream iTunes to my home stereo. This is the ONLY thing I use it for. It quit working and now Airport Utility cannot find the Airport Express unit, even after repeated re-boots of all components, resetting the Airport Express, even when connected directly to my router via Ethernet. I use a D-Link wirless router.
I downloaded the latest Airport Utility, but it will NOT work with XP (from the Apple website, not my words).
The Airport Express will achieve a solid green indicator after reset, but Airport Utility cannot find it. Until Utility can find and recognize the Airport Express hardware, I cannot adjust or reset any settings, etc.
Help!

I downloaded the latest Airport Utility, but it will NOT work with XP (from the Apple website, not my words).
The latest version of AirPort Utility.....5.6.1.....will only run on a Windows 7 machine.
Try AirPort Utility 5.5.3 for Windows (make sure that you have Service Pack 3 installed on your PC, otherwise the application will not run on an XP machine).
The Airport Express will achieve a solid green indicator after reset, but Airport Utility cannot find it.
After a "hard reset" or "factory default reset", the light will not be green.....it will be slowly flashing amber after it restarts. See this Apple support document for more information on various resets:
Resetting an AirPort Base Station or Time Capsule FAQ

Cannot configure the Airport Express

I connected my Airport Express to my router (not an Extreme Base station). I got the solid green light, I can see the network wirelessly and I can access the internet with no problems.
The problem is that I cannot access the Airport Express in order to configure it (I want to add some filtering and some additional security). The Setup Assistant is searching for an Extreme Base Station which it cannot find (since I do not have one) and so does the Airport Admin util.
Is there a way (or perhaps a different configuration utility for Win XP) to configure the Airport Express?
Thx
Windows XP

Thanks for the help. I was out of the country for a few weeks but now I am back trying to resolve the problem. Nothing helps, the Airport Express "insists" on the fact that it cannot find a base Station. I am not sure what else is there to do and I am closed to go back to my old 802.11b D-Link wireless router. Do you have any other idea that may resolve the problem?
On another note, why does there have to be any connection between the Airport Express and any base station? Why can’t I configure the Airport Express without being connected to any basestation?

Airport Utility can no longer see my Airport Express Base Station.

Hi all the problem I have is as follows;
I've set up my Airport Express Base Station some time ago to print wirelessly from my HP Photosmart C4280 and it was working fine.
However recently when I've gone to print a document, even though the printer is working fine and the Airport Express Base Station is showing a green light nothing happens. I've gone into the Airport Utility and its say's it can't see the Airport Express Base Station (even though it still has a green light showing). If I unplug the Airport Express and plug it in again, the Airport Utility can suddenly see it again.
I've successfully gone through the reset process but after a few minutes the Airport Utility can no longer see the Airport Express Base Station which means I can't print a document wirelessly. I've repeated the reset process several times with the same outcome.
Everything was working fine up until recently, has the Airport Express Base Station developed a fault? or is there something I'm not doing.
Any advice would be greatly appreciated.

If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices'

Updated my iTunes and now my mac can not see my airport express no matter what I have tried

recently updated my itunes and the firmware on my airport extreme and suddenly itunes does not recognize my airport express for speakers and my mac through airport utilities can not see my airport express. *** I have tried everything and nothing will bring the airport express back to life what to do

rosenkd wrote:
*** I have tried everything
... including a "hard reset" or a "factory defaults reset"?

I cannot get my Airport Express to accept wireless clients.

I cannot get my Airport Express to accept wireless clients. After resetting to factory default and reconfiguring, it works briefly but then stops again.
The Airport Express is on the second floor of my house and is seen by Airport Utility. Using a LAN cable with the Express works no problem.
My network is created by an Airport Extreme (ground floor) and extended by a Time Capsule (first floor)
Have run through all settings repeatedly and as I said I can get it to work briefly by resetting and then reconfiguring, but after a short while again my iOS devices can no longer connect and revert to cellular.

I cannot get my Airport Express to accept wireless clients. After resetting to factory default and reconfiguring, it works briefly but then stops again.
The Airport Express is on the second floor of my house and is seen by Airport Utility. Using a LAN cable with the Express works no problem.
My network is created by an Airport Extreme (ground floor) and extended by a Time Capsule (first floor)
The issue is most likely due to the fact that the AirPort Express may be too far from the AirPort Extreme to properly extend it with enough bandwidth to be useful.
It is important to understand that with Apple 802.11n or 802.11ac base station an extended network works in a wheel-like fashion with the base station to be extended at the hub and each extending base station along one of the spokes. This type of configuration does not allow for daisy chaining the base stations. That is, in your case, both the Time Capsule and AirPort Express are attempting to extend the AirPort Extreme.
Each extending base station must be within a certain signal quality range in order to extend the network properly. Please check out the following AirPort User tip for details.

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Hello Cloud19,
The article linked below provides some helpful information and troubleshooting that can help resolve issues with AirPlay and your Airport Express.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Cheers,
Allen

I lost my internet last night and now i cannot get my airport express to work

i lost my internet last night and now i cannot get my airport express to work it is blanking yellow on /off

Have you tried AirPort Utility it the Utility folder? If so, what was the result?

Cannot configure my AirPort Express (1st generation) anymore. Am using AirPort Utility 5.4.2 Setup Assistant. What do I do wrong?

I cannot configure my AirPort Express (1st generation) as base Station anymore. I had to reset it because I lost my password.
I first tried my IPads (IOS 6). These returned the message: Your AirPort Express cannot be configured with this software. Go to apple.com/nl/support/airport for more information.
As it is an old one, I have downloaded the eldest available AirPort Utility I could find on the Apple site (AirPort utility 5.4.2) to my computer. I ran the AirPort Setup Assistant wireless and the assistant found my AirPort named " Apple Network XXXXX". (I notes that the Assistant also returned the message: If this is not the AirPort Extreme you want to set up ...)
I clicked <NEXT>
After trying to connect to Network, I received the message: Cannot connect to network or there are no AirPort base stations on the network.
To be sure I retried running the Assistant after connecting the computer and the AirPort using an ethernet cable. The error message was the same.
What do I do wrong?
Am I using the wrong Utility software? If so, which version do I have to download and from where?
Is a first generation AirPort anyhow compatible wth 4the generation IPads or shoud I just buy a new AirPort.
I hope someone can help me...

Ok, thanks for clarifying that for me. You are correct. Your iOS devices will NOT be able to administer the 802.11g base stations because the version of the AirPort Utility that they use is incompatible.
For Windows XP, AirPort Utility for Windows v5.5.3 should work. However, v5.4.2 that you have should work as well.
Your XP computer needs to connect to the AirPort's wireless network BEFORE you can access the AirPort with the AirPort Utility. You may want to try connecting your computer directly to the AirPort using an Ethernet cable.

Airport Utility cannot find my Airport express on Windows 7

   I have a working Airport express with a static ip address. The static ip address has been hard coded in my main router. The airport express is connected to my network via ethernet cable. Airport Express Version 7.6.1. I am having conectivity issues from my new Windows Desktop. The airport utility 5.6.1 on my new desktop cannot find my airport express. The manual setup button has been greyed out. I can ping the device. I can click on "configure other" and configure the airport-express (which is how I set it up).    If I reboot my desktop and then quickly fire up the airport utility, it finds the device. On hitting rescan, in a few minutes everything gets greyed out again.
The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
How do I find out what is blocking the airport utility on my new desktop. The Bonjour Service is up and running.   Any help/advice on trouble shooting this issue is appreciated.

The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
You only need one computer on the network to access the settings in the AirPort, so unless you like to look for things, it is probably not worth the effort to try to troubleshoot the blocking action on the Windows 7 machine.
It is not always the Windows Firewall and/or the anti-virus program that blocks connection attempts like this, but that would be the first place to look.
In general, you have to get into the Firewall settings to create an "exception" for the AirPort connection. The same would be true for the anti-virus if that is what is blocking the connection attempt between the PC and AirPort.

Cannot see my Airport Express

Similar Messages

Maybe you are looking for