Cannot select Airport Express as speaker from iTunes

I have installed iTunes 7.6.2.9 on a MS Windows Vista Home Premium, and I get the speaker selector in the lower right corner as I´m used to, since I have an Airport Express connected to my stereo. I can also click the name of the AE, but the selection stays at "This computer".
The settings in the AE does not give me a clue as to what is wrong. Can anyone here help? Thanks in advance.
Best regards,
David List

Found the problem myself: the parental control settings in MS Windows Vista, which I had turned on for the sake of logging activity on my non-privileged user account. I had set the settings for this account so that nothing was restricted - it was just the logging that was done. Nevertheless, this was what gave me the problem with external speaker, and also with iTunes Store generally dying on me - or at least responding sloooooooooowly.
Best regards,
David List

Similar Messages

  • I am using an airport express to stream from iTunes to my stereo.  My router is a net gear type G.  Setting up is no problem for the first time.  But, when I close iTunes then restart I have to reset (using the reset button)and reset up.  Wanna do it one?

    Using a. Airport express to stream from iTunes.  My Router is a Netgear type G.  The express sets up fine and works the first time.  When I try to use it at a later date after closing then reopening iTunes I have to physically reset the express and then go through the process of finding it again.  Is this normal? 

    I have a 3rd generation (802.11n capable, 2.4Ghz only) airport express, my problem is that I've tried using it to extend my network and that brick wall, no matter how close I get the express to the room, the signal and throughput in that room becomes abysmal.
    As you might imagine, brick is a lot like cement, and it will not allow much of the wireless signal through.
    Regarding your Express, there is no such thing as a 3rd Generation model....yet. You likely have a 1st Generation AirPort Express. Check and confirm the Model No on the side of the Express. A 1st Gen model is A1264.
    Here's my problem, I don't think the express supports "extending" a network from a wired network jack.
    The Express can "extend" wirelessly, or using an Ethernet connection. The configuration for this is very simple, but post back if you need it.
    The jack just seems to be shut off
    Have you temporarily turned off the wireless on a laptop and tried to connect it using an Ethernet cable to the wall jack as a "test"?
    If you can get a good Internet connection this way, then you know the Ethernet cabling and jack are working correctly.
    On the other hand, if you cannot get an Internet connection on the laptop during this "test", then this indicates that the Ethernet cable or jack is not functioning correctly and the wiring will need troubleshooting before you can proceed any further.
    I need to create a whole new wireless network in this room for this configuration to work?
    AirPort Setup will take care of this for you automatically during the configuration of the AirPort Express.
    If I have an apple TV connecting to the express and an AppleTV connecting to the extreme, will they both be visible when connected wirelessly to either network?
    Yes
    Will I be able to connect to my network seemlessly?
    Yes
    Post back after you have confirmed that the Ethernet cable and Ethernet jack are functioning correctly in the temporary "test" mentioned above.  Then, we will continue.

  • Connection to airport express dies out from iTunes after 1-3 hours

    I have iTunes running in Windows XP. It is connected to zyxel WLAN AP through ethernet and Airport express is connected over wlan to this Zyxel. I have two problems where worse one is that after sometime 1-3 hours iTunes looses connection to airport express(remote speakers). Only way to return is to shut down power from AE. Then streaming can be started again. it seems that Internet connection is working all the time through zyxel, so this is not probably related to wlan itself
    Other problem seems to be that Itunes can find AE only after reboot. I have opened firewall, so good ideas what is wrong in these two problems.

    Yes, there's an exception for Bonjour in the firewall (Bonjour is allowed)
    I've try to re-add the "APAgent" which control Airports and restart the firewall but it didn't worked...
    The only solution I've found was to desactivate Windows firewall...
    (Firewall of my ADSL box is activated).
    Maybe I should try to repair iTunes Installation like WPLU...

  • I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

    I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

    Hello Hornet12,
    Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
    Using AirPlay
    http://support.apple.com/kb/HT4437
    AirPlay requirements and capabilities
    To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
    Stream content from
    Requirement
    Notes
    iPad
    iOS 4.3 or later.1
    From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
    With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
    iPhone (3GS or later)
    iPod touch
    (2nd generation or later)
    Computer
    iTunes 10.2 or later.
    Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
    Apple TV
    Apple TV software version 5.1 or later.
    Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
    Cheers,
    Allen

  • Cannot connect airport express to ipad I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    cannot connect airport express to ipad
    I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express.  Does anyone have a solution?

    I could not "see" my Express via my wireless router or via the Airport Utility until I reset it to Factory Settings by unplugging it then holding in the tiny reset button while plugging it back in, waiting for the flashing yellow LED signal before letting go.
    Then I set it up to DHCP - "connect to wireless network" and DOWNGRADED the firmware to 7.3.x
    I would tell you the exact Firmware but I can no longer "see" the Airport express............ AGAIN or still.....
    BUT at least I am listening to music streaming from my MacBook Pro... Hmmm.
    I log back into the router (Linksys WRT110) and it no longer shows the Airport Express as a DHCP client AND the Airport utility can no longer "find" any Airport Devices..
    So if I don't move, or there are no cosmic events, or maybe my KARMA is effecting the device or my "VIBES" are good, but I'm not sure if will continue to work.. Sure would like to use this little device from hel*.
    Since I have had this Airport Express I have spent many hours trying to get it to work.
    It works just long enough to fool me and then takes a dump...
    Maybe this time?
    5 Minute later...
    Music was playing. I went into iTunes and switched from Airtunes to Computer speakers. When I tried to switch it back GUESS WHAT?
    [An unknown error (-15006) occurred while trying to connect to remote speaker "Airtunes"]
    Wonderful Green LED though. Totally useless piece of equipment AFAIK.
    Message was edited by: Daniel Shattuck

  • Can I play tracks from my iPod via Airport Express on only from my laptop?

    I can play tracks from my laptop thorugh my Bose Lifestyle  Airport Express.  Is there a way to play tracks from my iPod Touch through my Bose system via Airport Express?   My Airport Express is set up as a client to my Sky Broadband wireless router.

    I set up my laptop to my Bose Lifestyle System via Airport Express. It may be different for MAC but I just downloaded the Airport Express software and followed the on-screen set-up procedure, which includes entering your WI-FI key.  I do not have an iPad.  You need to select Airport Express in iTunes as your sound media. This is easily switched by an icon in the bottom right corner of the screen.  You will need to switch this back if you want to revert to using the laptop speakers.

  • Apple AirPort Express - Streaming Music on iTunes - Frequent Music Drop out

    *Apple AirPort Express - Streaming Music on iTunes - Frequent Music Drop outs*
    I have just purchased an Apple AirPort Express for the sole use of streaming music from my laptop to my home cinema system.
    My system has bundles of power (Core 2 Duo, 3gb RAM, 320gb hard disk, Intel-N WiFi) and is running Windows Vista Premium. I am using the latest version of iTunes (version 8) and have it setup to play through remote speakers. I have my AirPort Express connected to my home cinema system.
    When I play music on iTunes through ONLY my computer speakers I have no problem with drop outs.
    However, when I play music through either (1) my AirPort Express or (2) multiple speakers (i.e. the AirPort Express and my computer speakers together) I experience frequent and unbelievably annoying drop outs in the music stream.
    I have determined this has nothing to do with interference with the wireless signal and believe this is something to do with iTunes - the reason being the drop outs occur in BOTH the computer speakers AND the AirPort Express speakers (when I select multiple speakers) but does not occur when I select ONLY the computer speakers.
    Please could you provide some advice on this as I am unable to use the AirPort!
    Many thanks
    Elliot

    You don't say which Airport Express you are using and what its settings are.
    There are two Airport Express models. The original model works on 802.11b/g on 2.4 GHz. The later model can do 802.11n on 2.4 GHz or 5.0 GHz. My experience is that interference when using the 2.4 GHz band creates drop-outs when sending audio from iTunes to an Airport Express. I now have an 802.11n network on 5.0 GHz and no longer have drop-outs. I also have a 2.4 GHz 802.11g network for my iPhone and other devices that can't do 802.11n. They are connected to each other by ethernet.
    Interference on 2.4 GHz occurs because a lot of people nearby have wireless networks too. You may not notice the interference when doing other network activity that is not time dependant but it shows when streaming music. Using a utility like iStumbler or AirRadar I can see I am the only one using the 5.0 GHz band in range of my computer.

  • Cannot connect Airport express wireless

    Hello, cannot connect airport express wireless to linksys router.  Connected now with ethernet  cable but cannot figure wireless connection. My laptop cannot find the express while preforming setup scan, yet I'm connected to it.  I can connect with my iphone but not wirelessly. Any suggestions?

    ....I was then told over the phone that airport express will not connect to third party routers.
    This is NOT correct.
    The AirPort Express will connect to a wireless network if you know the following:
    1) The name of the wireless network
    2) The exact setting for wireless security that the network is using
    3) The wireless network password
    Most users know 1) and 3), but very few know the exact type of wireless security settings that their wireless router is using. The Express will not connect to the wireless network unless it receives all of the information listed above.
    So...we will assume that you know the name of the wireless network and the password for the network.
    Do you know the exact type of wireless security setting that your wireless router is using?  If not, the Express will not connect.
    You may need to check the setup of your wireless router....or if the router was supplied to you by an Internet Service Provider, they may be able to tell you what type of wireless security setting is being used.
    Post back when you have this info and we will proceed. There are still no guarantees that the Express will connect....but at least there may be a chance.

  • Restore needed iphone cannot make or receive calls restore from itunes

    restore needed iphone cannot make or receive calls restore from itunes www.apple.com/support

    Hi donte001,
    I apologize, I'm a bit unclear on the exact nature of your issue. If you are having issues making or receiving phone calls on your iPhone, you may find the troubleshooting steps outlined in the following article helpful:
    iPhone: Troubleshooting issues making or receiving calls
    https://support.apple.com/kb/TS3406
    Regards,
    - Brenden

  • Iphone cannot make or receive calls. restore from itunes

    Hey, my iphone 4s said "iphone cannot make or receive calls. restore from itunes" but when i try to restore it, there is a -1 error. please help

    Connect the phone to your computer and open iTunes. It should prompt you to restore. If it doesn't see this:
    http://support.apple.com/kb/HT1808

  • ITunes cannot see Airport Express / Windows XP

    I have an interesting problem that I cannot figure out.
    I am only using the Airport Express to stream music to my stereo. Therefore the Airport Express is in client mode, connected to my home network over a wireless connection (predominantly D-link hardware), WEP is enabled and working fine, and all hardware has the latest firmware. Finally, all hardware has functioning internet connections.
    My Apple Powerbook with its Airport card can connect to my Airport Express (in client mode) without difficulty. The Aiport configuration programs can "see" the Airport Express and iTunes finds the device fine. The Powerbook works the way it should, and I can stream music the way I want.
    However, the problem is that my IBM notebook cannot see the Airport Express through any of the configuration utilities, and iTunes on the notebook cannot find the Airport Express. I have tried disabling all firewall and antivirus software. iTunes is configured to look for remote speakers with Airtunes. No dice on streaming music from the IBM Notebook to the Airport express.
    What is strange is that on the IBM notebook, I can open the Airport Admin Utility and choose "other." Then I put in the IP address for my Aiport Express 192.168.0.103, and I can communicate and configure the Aiport Express.
    So the problem is iTunes cannot find the Airport Express on my IBM laptop. I have tried everything that I know of to solve the problem. I can communicate with the Airport Express on the IBM by using the "other" command in the Admin Utility. Somehow there is a flag or something that is not coming up automatically to let the notebook know that an Airport Express is in the network.
    Suggestions?

    Have you tried re-installing iTunes as the problem may lie with that and not the network setup itself.

  • Can't even select AirPort Express in iTunes

    For whatever reason, the remote speakers are listed in my iTunes, but I can't even select it. It won't connect and it won't even let me choose to try to connect to them... but they are shown as an option. What gives? You can select and play through my other Mac computers, but not this one. Does anyone have any thoughts as to what is going on?
    Thank you in advance...
    - Jay

    Welcome Albert.Pang,
    Have you tried to power cycle your Airport Express? Unplugged it from its power source and wait 10 seconds and plug it back in and wait 3 minutes and try Airport Admin Utility again.
    or
    Have you tried to reset your Airport Express? While plugged in to its power source take a paper clip and push the little button next to the Audio Port and hold it in for 10 seconds. Unplugged the Airport Express from its power source and wait 10 seconds and plug it back in. Now you will have to use Airport Setup Assistant again.
    I hope this helps....
    Powerbook G4 1.67 15", 1 gig ram, 128 vram, 80 gig harddrive   Mac OS X (10.4.6)   Powermac G3 266 mt, Dell 5150,ibook G4, 1 gig shuffle, epson printers, airport

  • Itunes - airport express - remote speaker not compatible?

    Airport Express unit (AX) connects to my network and verified to be connected to the network just fine...but on itunes (v. 7.4.2.4) on my desktop (Dell Dim E510 with wireless, Windows XP, Linksys router WRT350N with AX for airtunes)...when I switch speaker to the AX/stereo unit, comes back with message - "the remote speaker xxx is not compatible with this version of itunes"... I've battled this issue for a long time -- any idea what is the problem?

    OK I got it working again. I'm not sure exactly what did the trick, but I'd recommend the following:
    1. Repair your wireless modem connection via your taskbar (rick-click on the Wireless Network Connection, Repair)
    2. Start itunes while the Airport Express Setup Assistant is running
    3. Restart your computer
    4. Keep trying, after 2 days it's working again (???)

  • Does iTunes/Airport Express support speaker-specific volume control?

    Hi there,
    So say I have two Airport Expresses, one in the living room with speakers and another one in the bathroom with speakers. Can I setup the volume in the bathroom to be lower?
    Thanks.

    You can do this using Airfoil at http://rogueamoeba.com/airfoil/

  • Cannot see Airport Express as an Audio Output option!

    Hello All,
    Very frustruating.
    I bought an AirPort Express hoping to use it as a Audio output device for movies/spotify etc.
    Plugged it all in to my reciever (using optical cable) configured it to my TC network.
    Opened itunes and the Airplay function is working perfectly. Music is streaming as expected.
    However i cannot see the AE in the audio output options (when i "option+click" the speaker icon).
    Tearing my hair out as this was the primary reason for purchasing the AE!
    any help would be greatly apprecaited.
    Tim

    Trying to play movies through VLC and stream the Audio component to my AirPort express. Similary use Spotify on my computer and stream the audio component.
    I thought i would be able to enable my laptop (Macbook Air) to use the Airport Express as its 'speakers' through selecting it as the output source in System preferences.
    However it does not show up in the system preferences at all, what has me stumped is the Airport Express is 100% functional through itunes as well as some third party applications (Airfoil).
    Im very confused as other users (from extensive google searching) appear to be able to atleast see the AirPort Express as an output device.
    Any help greatly appreciated.

Maybe you are looking for

  • In Photoshop elements 13, the elive button does not appear in expert mode.

    This is happening in the trial version. Windows 7,  hp530 laptop.

  • Why is DW CS4 not elipse based

    I have been so busy I just noticed the DW Beta. I have been using DW since the beginning for prototype UI creation. I also used homesite before that. I was holding my breath & hoping DW CS4 would be eclipsed based. Not only would it gain some credibi

  • Boot Camp Reveals Deeper Problem?

    Today, I tried to install Windows onto my new MacBook using the Boot Camp software. However, it told me that I could not partition the disk and that I needed to run a "Repair Disk" in order to be able to do so. I proceeded to do this, but it gave me

  • Package assigning issue to object which is moved from other system

    Hi Experts, We have moved one develoment (workflow development) from one server to another server with basis people help and can see everything perfecly in my system . But , i need to save them under my own requyest ,then only i can move them to prod

  • Priming cache by reporting agent problem

    Hello All, I have few questions regarding article on bwexpertonline for priming the cache. The article is really great and big help....but i am not getting out put the way it should be. 1) I created a query  - which doesnt have any variable/selection