Cannot select between express profiles?????

I have two scenarios for two locations in which I use my airport express to connect to remote speakers for iTunes
1. HOME - Join an existing wireless network at my home.
2. WORKSHOP - Create a wireless network at my workshop.
For each of the above scenarios, I have set up a profile with the Airport Utility.
If I have it set to Home, it works perfectly at home. But, when I take it to my workshop, the airport cannot be found even though I have a "workshop" profile. If I cannot find the express, then I can't change the profile over to workshop.
I know that the workshop profile works because I have reset the the express at my workshop and set it up to create a wireless network, and when I take this home, I just select the airport's wireless network that it is creating and make a new profile for home in which it joins an existing wireless network.
By alternating daily between the two locations, I have to reset the airport every time I want to use it at my workshop. I suppose I could change the profile at home to workshop before I leave, but I'm hoping someone has a better solution. Thank you.

It would be nice though if the airport would ask you which profile you want if it doesn't recognize it's environment. At least to be able to change it anytime without resetting would be a little more user friendly.
I wholeheartedly agree on both counts ...
Maybe apple could update the software to help this???
You might want to provide this suggestion directly to Apple? Here's the link:
Product Feedback

Similar Messages

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

Hello Hornet12,
Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
Using AirPlay
http://support.apple.com/kb/HT4437
AirPlay requirements and capabilities
To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
Stream content from
Requirement
Notes
iPad
iOS 4.3 or later.1
From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
iPhone (3GS or later)
iPod touch
(2nd generation or later)
Computer
iTunes 10.2 or later.
Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
Apple TV
Apple TV software version 5.1 or later.
Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
Cheers,
Allen

Cannot select Airport Express as speaker from iTunes

I have installed iTunes 7.6.2.9 on a MS Windows Vista Home Premium, and I get the speaker selector in the lower right corner as I´m used to, since I have an Airport Express connected to my stereo. I can also click the name of the AE, but the selection stays at "This computer".
The settings in the AE does not give me a clue as to what is wrong. Can anyone here help? Thanks in advance.
Best regards,
David List

Found the problem myself: the parental control settings in MS Windows Vista, which I had turned on for the sake of logging activity on my non-privileged user account. I had set the settings for this account so that nothing was restricted - it was just the logging that was done. Nevertheless, this was what gave me the problem with external speaker, and also with iTunes Store generally dying on me - or at least responding sloooooooooowly.
Best regards,
David List

IPhone: Cannot select my provisioning profile - tried all suggestions

I am attempting to load an application onto an iPod Touch. I have followed the PDF document at the iPhone Program Portal to the letter, creating a development certificate with name and e-mail address that matches my agent information, a device profile, app IDs with several variations, including com.companyname.myapp, com.companyname.*, * and myapp, and provisioning certificates (one at a time) based on these.
Both the Apple WWDR certificate and my developer certificate are present in my keychain. It appears I have two keychains - system and login. I have loaded both certificates into one, the other or both keychains.
In XCode, my provisioning profile appears in the organizer, and also appears on the device. In the properties for my project I have set the bundle identifier to the matching variation of the app id used with the device profile, both with and without the Apple prepended identifier. Under the Code Signing Identity I have tried the default value, no value and "iPhone Developer: FirstName LastName."
I have removed all the components from the program portal and recreated them from scratch several times.
No matter what the permutation, my provisioning profile does not appear under the Code Signing Provisioning Profile key. Whether this field is left as the default or the name of my profile is forced in, XCode successfully builds the project with the device as a target, but upon trying to upload reports "an unexpected error 0xE8000001 during the install phase: Verifying application." I have restarted the device multiple times, without effect. I am never asked for a password to access my keychain.
I have read all the threads in the discussion groups on this topic, and tried their suggestions to no effect. I am using the latest version of the SDK (9M2199a), my iTunes is the latest released version (NOT the developer pre-release), the device is running the latest release version of the OS (2.0.1 - 5B108), and I am running the latest release version of Leopard (10.5.4).
Developer support recommended I file a bug report.
Does anybody have any further suggestions?

1. You may have to rebuild your certificates and your provisions. Soemtimes it can be hit and miss even when followign the pdf.
2. If you already managed to get a copy of the app on the device delete it directly from the device. Sometiems the system throws an error if it can't delete it.
3. Certificates go in the login keys.
4. These days you can downlaod the providsion and drag it to iTunes in dock while your phone is plugged in.
(Have xcode off when you do this since it seems to cache data)
5. Check the console to make sure it's checked and for any error messages (minimal info)
6. Once you've installed the certificates and the provision shut down and restart.
7. There are 2 places to set the provision. Select the project (top level) on the left in xcode. Do a get info. iPhone Developer: Your Name (note the space after : This needs to match EXACTLY to your certificates which shoudl show up in Keychain Utility under Keys.
8. Once you have the Developer name then select the provision. If there's none available check mobile provisions in the library and make sure it got copied there.
9. The other place you need to set the provision is select target on left in xcode. Get Info. Set iPhone Developer: Your Name and set the provision popup.
10. Make sure to do a full clean and then rebuild.

Cannot select ldap user profile for SGD Global Admin

Hi all,
I'm trying to select some ldap users to be in the SGD Global Administrators role, but I am unable to check the check box next to the user profile once I navigate to the account. There is no check box to check.
I am actively using LDAP for regular user auth and application assignment, so I know my LDAP "works" in that sense, I just can't use it to assign global admins.
Any thoughts?
Adam

The only way to do this is to create a user profile for the (would-be) admin account. And since they're an LDAP user, you'll have to use LDAP mirroring to do this. For example, let's say the user you want is "cn=Joe Admin, ou=Users, dc=example, dc=com"
Go to "User Profiles", and browse to/open:
dc=com
cd=example
create the directory object "ou=Users"
Inside of "ou=Users", create the user profile object "cn=Joe Admin"
Add this user object to the Global Administrators role.
http://docs.sun.com/source/820-4907/chapter3.html#d0e13589

Cannot select multiple speakers ( airport express)

cannot select multiple speakers in itunes ( have two airport expresses) ... tries to connect and then always times out.

Only firewall I have is what is standard on my mac, and if that is what your talking about, I do not know how you do that UDP traffic thing.

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Hello Cloud19,
The article linked below provides some helpful information and troubleshooting that can help resolve issues with AirPlay and your Airport Express.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Cheers,
Allen

Steady green light on A1084. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it. Is there a fix?

Steady green light on A1084. Mac OS X 10.7.5. IMac. Verizon DSL Actiontec GT704-WGB modem. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it and send a signal to airport express to play airtunes through my stereo amplifier. Is there a fix?

I plugged a model A1034 Airport Extreme Base Station into the Verizon DSL Actiontec GT704-WGB modem with an ethernet cable and now the AirPlay icon appears in the Itunes window immediately to the right of the volume control and I can select it and play Airtunes wirelessly through the A1038 Airport Express Base Station in another room connected to a stereo amplifier by a Monster mini-to-RCA left/right audio cable running from the output jack on the A1034 Airport Express Base Station into the CD jacks on the amp. The problem is that I have to select the Apple Network Airport Express Base Station as my network in order to select the Airport Express Base Station when I click the AirPlay icon, which means I have no Internet signal to the Imac. If I select the Airport Extreme Base Station or the Verzion modem as my network, then I have an Internet signal to the Imac, but the Airport Express Base Station is grayed out when I click on the AirPlay icon, so I cannot select the Airport Express Base Station and send tunes to the Airport Express. It would be nice to play Airtunes while simultaneously accessing the Internet. I don't understand your question about what program I am using for which I require AirPlay. I am not learned about computers in general, and even less so about Macs than PCs. I thought the program I was running was Itunes, and there was no separate program to run to use AirPlay for the purpose of sending a signal from the Itunes on the Imac to the A1084 Airport Express base station in a another room, and then out as described above to the stereo amplifier to listen to Itunes music remotely in the other room, without any kind of cable, wire, etc., connecting the Imac to the stereo amplifier. I would guess that the most common use for the A1084 is to play Itunes through a stereo in another room without the need to run wires from the computer to the stereo. I realize it would be easy simply to run a very long mini-to-RCA left/right audio cable across the floor connecting the Imac to the amp without the need to use AirTunes, Airplay or any kind of AirPort, but it would be both unsightly and a tripping hazard.

Cannot convert between unicode and non-unicode string data types.

I'm trying to copy the data from 21 tables in a SQL 2005 database to a MS Access database using SSIS. Before converting the SQL database from 2000 to 2005 we had this process set up as a DTS package that ran every month for years with no problem. The only way I can get it to work now is to delete all of the tables from the Access DB and have SSIS create new tables each time. But when I try to create an SSIS package using the SSIS Import and Export Wizard to copy the SQL 2005 data to the same tables that SSIS itself created in Access I get the "cannot convert between unicode and non-unicode string data types" error message. The first few columns I hit this problem on were created by SSIS as the Memo datatype in Access and when I changed them to Text in Access they started to work. The column I'm stuck on now is defined as Text in the SQL 2005 DB and in Access, but it still gives me the "cannot convert" error.

I was getting same error while tranfering data from SQL 2005 to Excel , but using following method i was able to tranfer data. Hopefully it may also help you.
1) Using Data Conversion transformation
data types you need to select is DT_WSTR (unicode in terms of SQL: 2005)
2) derived coloumn transformation
expression you need to use is :
(DT_WSTR, 20) (note : 20 can be replace by your character size)
Note:
Above teo method create replica of your esting coloumn (default name will be copy of <coloumn name>).
while mapping data do not map actual coloumn to the destination but select the coloumn that were created by any of above data transformer (replicated coloumn).

Cannot select multiple airports using remote app.

Why can't I select multiple airport express units using the remote app?

Thanks for the reply.. I also tried that way.. I face couple of issues
1) I could not find an option of saving a Draft Message
2) After multiple recipients(I have selected 12 recipients) in "TO" section, if I type a word in "TO" such as "Pre", it shows me all the contacts containing "Pre" but I cannot select the last contact incase there are more than 20 contacts coz I am unable to scroll down till the end.. If I do so.. I cannot select coz screen scrolls up automatically..
Pls try ... If required I will insert video

Cannot select from dropdown list

This is very weird. I am a long-time FF user. Suddenly, I find that I cannot select from a dropdown list. Clicking on the list shows all the options but moving the mouse doesn't change the highlighted option.
Safe Mode - Didn't help
New profile - Didn't help
What is going on here? Please help. Thanks

Troubleshooting plugins
* https://support.mozilla.com/en-US/kb/Troubleshooting%20plugins
Check and tell if its working.

Cannot select Us Europe Asia options on yahoo finance home page

The web page is finance.yahoo.com
Cannot select the US Europe Asia options on this page.
The cursor should show a hand with pointing finger when hovering over these areas
but does not change from normal cursor shape.
This problem first showed up today March 8th.
Works OK with microsoft explorer.

This style rule in userContent.css or Stylish should do it.<br />
I don't know if there is a better way to fix it in this case as I'm not a expert in this matter.
Add code to the userContent.css file.
*http://kb.mozillazine.org/userContent.css
The customization files userChrome.css (interface) and userContent.css (websites) are located in the chrome folder in the user profile folder.
*http://kb.mozillazine.org/Editing_configuration
<pre><nowiki>@-moz-document domain(finance.yahoo.com){ .yui3-tab-panel-selected { position: static !important; } }
</nowiki></pre>

I cannot select previously searched items in google toolbar search through mouse, I have to selct it by keyboard or retype it.

In firefox 4 I cannot select previously searched items in google toolbar search through mouse, I have to selct it by keyboard or retype it.
Also during switching between tabs I notice black screen.

I just tried clicking the left button of the mouse BEFORE placing the pointer above the drop-down arrow of the Google search and worked. If the word was deep down the list, i scrolled down the wheel of the mouse. Always keeping the left button pressed and releasing it once i had pointed my choice.

Does the condition specified in the function 'DECODE' allow 'BETWEEN' expression?

Does the condition specified in the function 'DECODE' allow 'BETWEEN' expression?

As a completely different approach, in 8i SQL and 9i PL/SQL we can use the CASE function. This delivers decode functionality, but allows us to use conditions e.g.
SELECT CASE WHEN col BETWEEN 1 and 9 THEN 'one' ELSE 'two' END FROM my_table;I love DECODE and wouldn't use anything else for straight value substitutions but CASE does have the advantage of clarity when it comes to maths, etc. Also I believe DECODE is not ANSI compliant. In which case (ho ho!) I suspect it will probably be deprecated, as Oracle seems to be moving towards ANSI SQL compliance, as part of its open standards drive.
Cheers, APC

Cannot convert between unicode and non-unicode string datatypes

My source is having 3 fields :
ItemCode nvarchar(50)
DivisionCode nvarchar(50)
Salesplan (float)
My destination is :
ItemCode nvarchar(50)
DivisionCode nvarchar(50)
Salesplan (float)
But still I am getting this error :
Column ItemCode cannot convert between unicode and non-unicode string datatypes.
As I am new to SSIS , please show me step by step.
Thanks In Advance.

My source is having 3 fields :
ItemCode nvarchar(50)
DivisionCode nvarchar(50)
Salesplan (float)
My destination is :
ItemCode nvarchar(50)
DivisionCode nvarchar(50)
Salesplan (float)
But still I am getting this error :
Column ItemCode cannot convert between unicode and non-unicode string datatypes.
As I am new to SSIS , please show me step by step.
Thanks In Advance.
HI Subu ,
there is some information gap , what is your source ? are there any transformation in between ?
If its SQL server source and destination and the datatype is as you have mentioned I dont think you should be getting such errors ... to be sure check advance properties of your source and check metada of your source columns
just check simple oledb source as
SELECT TOP 1 ItemCode = cast('111' as nvarchar(50)),DivisionCode = cast('222' AS nvarchar(50)), Salesplan = cast(3.3 As float) FROM sys.sysobjects
and destination as you mentioned ... it should work ...
somewher in your package the source columns metadata is not right .. and you need to convert it or fix the source.
Hope that helps
-- Kunal
Hope that helps ... Kunal

Cannot select between express profiles?????

Similar Messages

Maybe you are looking for