Cannot setting up my Cisco router on maverick

When I setting up router, it has problem of setting. But I using the other run lion MacBook Air . It doesn't error. What happen?

I'm not sure but try this:
Connect the laptop to the device and wait for a while.
If there the router has DHCP enabled you will get an IP from the router.
Use command line:
windows 7:
-press start
-type cmd and run it
-type ipconfig
-find your NIC and the default gateway
-copy the default gateway in your browser!
In linux same but use terminal and command is "ifconfig"
Hope this helps
edit: This may also help you

Similar Messages

Cannot set display resolution after upgrading to Mavericks

I have early Mac Mini connected to KVM stitch. Over the weekend I upgraded to Mavericks and it "dowgraded" display resolution from 1920x1200 to 1600x1200 and everythign looks streached. 1920x1200 no longer shows on the list in display properties (1920x1440 shows but it does not look good on my screen). I googled Option key trick and hitting "Scaled" while hold Option key does show some additional resolutions, but not the one I used to have.
Connecting Mac directly to the monitor allowed me to set proper resolution and after removing monitor and pluging mac back into KVM things "held" untill Mac goes to sleep or until reboots.
I am aware that my KVM switch does not communicate EDID but things did work just fine before upgrade to Mavericks.

Hello curtdav,
It sounds like you are getting a graphical anomoly when unplugging an external monitor. I recommend these troubleshooting steps from the article named:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Reset the system
You can reset the Mac's parameter RAM and SMC.
Reset the resolution
Start by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
Thank you for using Apple Support Communities.
Take care,
Sterling

Vlans and cisco router

I have a netgear managed switch and a cisco 1750 router. I would like to set up 2 vlans. the first one is a wan, with a residential cable model connected to it. the other vlan is for my private lan. I will then have the cisco router connected to one port on the switch set up as a trunk. I'm no pro, but from what I've read so far, it should work that way, right? the part I need help with is setting up the cisco router as a gateway and dns proxy, accepting the dynamic ip, gateway, and dns addresses from the cable modem.
I did see this http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Getting%20Started%20with%20LANs&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddcef50
router in a stick *write that down* so my setup should work if I can figure out the router configuration. a good online tutorial or something would be helpful for this. I have plenty of cisco books, but maybe something for dummies would help me get started, before digging into the tough stuff.

In order to set up inter vlan routing or a "router on a stick" with a netgear switch you will need a router that supports IEEE 802.1q VLAN Support.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t1/8021q.htm#28767
On the router interface that is "trunked" to the switch you will need to have a configuration that looks like the what I have below.
Router(config)#interface FastEthernet0/1.1
Router(config-subif)#encapsulation dot1Q 1 native
Router(config-subif)#ip address 10.xx.xx.16 255.255.255.xxx
Router(config-subif)#interface FastEthernet0/1.2
Router(config-subif)#encapsulation dot1Q 2
Router(config-subif)#ip address 10.xx.xx.130 255.255.255.xxx
The sub-interface 1."2" corresponds to the vlan id on the trunk. In this case the .2 is vlan 2.
I have attahced a link that exlains the intricate details on inter vlan routing below:
http://www.cisco.com/warp/public/473/50.shtml
Lastly you may want to check the Cisco IOS feature Navigator. I was looking at it and I did not see that the 1750 has IEEE 802.1q VLAN Support. It looks like the 1751 is the first platform in the 1700 series that does.

Setting up an HP printer through a cisco router

A friend has just bought a new ibook converting over from the PC world and is trying to set up his HP Deskjet 9300 printer to work with a cisco router. The printer works when set up directly to his G4 ibook but not through the router. We have set the IP addressess so we are getting the router wlan light to flash but the lan light does not come on. I think the problem may be what we have entered in the info fields but but cannot find any information to set me straight. I will be heading over this evening to try to help him again so if anyone has some info that will help it will be appreciated - Thanks in advance

Printing to a network ethernet printer (which has an IP address) from a Mac running OS 10.3.x
http://www.ifelix.co.uk/tech/3005.html

I am getting an un expected error message when updating the setting to "extend network". Is there an obvious setting I may be missing? Cisco router being used.

I am getting an un expected error message when updating the setting to "extend network". Is there an obvious setting I may be missing? Cisco router being used.

If you are trying to "extend" using wireless only, you may not be aware that Apple designed the "extend" feature as a proprietary setting to only work with other Apple routers.
It is extremely unlikely that this will work with a Cisco router.
If your plans call for connecting the AirPort Express to the Cisco router using a wired Ethernet connection, it should be possible to configure the Express that way.

My Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

my Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT201364 I've downloaded Mavericks, but cannot set up the installation.

I've downloaded Mavericks, but cannot set up the installation. The clock just keeps turning, and I can't continue or exit. Any idea of what to do next? I believe my system meets the requirements, although I'm not real sure of the age (I think I purchased mid 2007 or early 2008).
Model Name:          iMac
Model Identifier:          iMac7,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          4 MB
Memory:          4 GB
Bus Speed:          800 MHz
Boot ROM Version:          IM71.007A.B03
SMC Version (system):          1.21f4
I appreciate anyone's help.

Mid 2007 or later should be ok >   OS X Mavericks: System Requirements
How long has the installation taken so far? On a high speed broadband connection, it should take about 45 mins to an hour.

HT4519 I switched to a Cisco Router model EA6500, in now periodically receive a message on both of my email accounts "cannot get email" the connection to the server failed" it's happening on both by iPad and iPhone. I've talked to Cisco and they couldn'

I switched to a Cisco Router model EA6500, in now periodically receive a message on both of my email accounts "cannot get email" the connection to the server failed" it's happening on both by iPad and iPhone. I've talked to Cisco and they couldn't help

Start by working throudh the Troubleshooting iOS and WiFi knowledge base article and see if that helps the situation. When you get to shutting down the router, be sure to disconnect power as shutdown on some is really just standby mode.

Setting PPPoE clients speed Via Cisco router

Hi i have a 7200 cisco router working as NAS (network access server) for PPPoE sessions , the clients connected DSLAMS and the Cisco connected to an AAA external Raduis server.
i want to set the user speed Via cisco router in a way which can be controlled in the Radius server , and not through the actual speed of the DSLAMS ports
Thanks alot

Hello Mohamed,
there is a feature called controlled subscriber bandwidth that may fit your needs:
see
http://www.cisco.com/en/US/docs/ios/bbdsl/configuration/guide/bba_con_sub_bdwth_ps6441_TSD_Products_Configuration_Guide_Chapter.html
it manipulates the ATM traffic parameters on a per user basis
these settings can be done on radius AV:
example:
The following example shows how to configure RADIUS attributes for a user profile for DBS:
[email protected] Password = "userpassword1", Service-Type = Outbound
     Service-Type = Outbound,
     Cisco-Avpair = "vpdn:tunnel-id=tunnel33",
     Cisco-Avpair = "vpdn:tunnel-type=l2tp",
     Cisco-Avpair = "vpdn:l2tp-tunnel-password=password2",
     Cisco-Avpair = "vpdn:ip-addresses=172.16.0.0",
     Cisco-Avpair = "atm:peak-cell-rate=155000",
     Cisco-Avpair = "atm:sustainable-cell-rate=155000"
Hope to help
Giuseppe

Set cisco router for dhcp

hi ! i want to set up r1 and r2 (see below) to get ip address from r3. what do i need to configure on all routers. thanks.
r1---r2--r3

Hi,
To configure a Cisco router as a DHCP server:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca75c.html
To acquire an IP address via DHCP on an Ethernet interface of the router, use the following command in interface configuration mode:
Router(config-if)# ip address dhcp
The question is how are your routers connected (what type of interfaces), and what is the purpose of this topology.
HTH,
Mohammed Mahmoud.

How do I set up my hp laserjet printer through Cisco router?

I'm using my HP Laserjet 4000TN printer for my entire network. I need to be able to use it with all my computers. So I usually plug it into the modem via Cat5 cord and it grabs an IP address which I add in System Preferences and I'm good to go. However, I recently had to change my network. I now use a DSL modem as basically a dumb hub. Which then goes into a Cisco 800 series router. From there I need to be able to plug my computer into that router and then see it on both of my computers. (What's the point of having a home network if you can't print from it from any computer on the network?)
I was told to assign it a static IP address of 192.168.7.5. However, when I do this on my computer it doesn't seem to be going through to the printer. Whenever I try to print a test page it does not work.
It is grabbing IP address 192.168.7.22. However, when I enter this as the printer on the computer it is also not printing a test page. Very frustrating. I am unsure if this is the perfect forum for this as obviously it's the Cisco router that has changed and therefore it's not really a Mac issue. But I am unsure where else to turn.
Any help would be greatly appreciated.
Thanks!

I found the solution. I was using WEP encryption and I needed to be using WPA encryption.

Remote access VPN with Cisco Router - Can not get the Internal Lan .

Dear Sir ,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Below is the IP address of the device.
Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
IP address:10.10.10.1
Mask:255.255.255.0 F0/0
IP Address :20.20.20.1
Mask :255.255.255.0
F0/1
IP address :192.168.1.3
Mask:255.255.255.0
F0/0
IP address :20.20.20.2
Mask :255.255.255.0
F0/1
IP address :192.168.1.1
Mask:255.255.255.0
I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
Need your help to fix the problem.
Router R2 Configuration :!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R2
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip tcp synwait-time 5
interface FastEthernet0/0
ip address 20.20.20.2 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Router R1 Configuration :
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login USERAUTH local
aaa authorization network NETAUTHORIZE local
aaa session-id common
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
username vpnuser password 0 strongpassword
ip tcp synwait-time 5
crypto keyring vpnclientskey
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group remotevpn
key cisco123
dns 192.168.1.2
wins 192.168.1.2
domain mycompany.com
pool vpnpool
acl VPN-ACL
crypto isakmp profile remoteclients
description remote access vpn clients
keyring vpnclientskey
match identity group remotevpn
client authentication list USERAUTH
isakmp authorization list NETAUTHORIZE
client configuration address respond
crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
crypto dynamic-map DYNMAP 10
set transform-set TRSET
set isakmp-profile remoteclients
crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPNMAP
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip local pool vpnpool 192.168.50.1 192.168.50.10
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
no ip http server
no ip http secure-server
ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
ip access-list extended NAT-ACL
deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended VPN-ACL
permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
end

Dear All,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Waiting for your responce .
--Milon

Help with Remote access VPN on Cisco router 3925 via Dialer Interface

Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
        quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
Thanks

Hi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0         192.168.1.1     YES NVRAM up                    up
GigabitEthernet0/1         unassigned      YES NVRAM up                    up
GigabitEthernet0/2         unassigned      YES NVRAM up                    up
Dialer1                    210.245.54.49   YES IPCP   up                    up
Dialer2                    101.99.7.73     YES IPCP   up                    up
NVI0                       192.168.1.1     YES unset up                    up
Virtual-Access1            unassigned      YES unset up                    up
Virtual-Access2            unassigned      YES unset up                    up
Virtual-Access3            unassigned      YES unset up                    up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much !

HT5569 Yesterday, my ability to receive gmail, facebook, safari,etc.ceased on my ipad2. The wifi shows it is connected and the cisco router works ok with another computer connection. Can anyone tell me what I need to do with ipad in order to get it worki

Yesterday, my ability to receive gmail,facebook,safari,etc. ceased to perform The wifi connections shows that it is connected but I cannot get through the internet . I use a Cisco router and it is working fine with another computer and also a printer. I contacted the internet provider and they show the ipad at the router but not out through the internet. Also, yesterday my wife eliminated some programs(games,etc) from the ipad. Anway, I am thinking I am missing some setting that is not turned on as everything seems to be working fine.
Any suggestions?

Settings > General > Reset > Reset Network Settings

Problems connecting to a Open Network via Wi-fi on Cisco Router

Hi everyone, I know I'm new here but I'm in need of your help, so if you can assist please do so as I cannot live without wi-fi and might have to go back to my nokia again if I can't sort this out.
Vodafone finally released the Iphone on their network in Ireland today and I've picked a 3gs up straight away.
At work I have a wi-fi network with a CISCO router (I have no access to the router as only IT do and they won't change anything to satisfy me and my Iphone anyways). This network has no encryption whatsoever and its free to join, you don't need any password or anything. My nokia at the start couldn't connect as it said that the network needed a pre shared key, this isn't true and in the end it was just change a setting to no auth required for it to log into the network and work perfectly.
Today I got to work and the Iphone can't connect to the network, just says it can't join the network. I cannot find anything about authentication on the settings of the phone nor can I work around this at all. I've had a Ipod touch for (the 2nd gen) for over 2 years and I gave up trying to set it up at work because I just couldn't find what was wrong with it, I ended up almost not using it other than when traveling or on the gym.
So first question is there any way I can access the authentication settings for wi-fi connections on the Iphone? Maybe its just a little change that is needed like the nokia.
Has anyone experienced this problem on a open network that they cannot join?
Any other sugestions? Anything really?
Thank you very much for your time guys, I would really really appreciate your help on this.
Regards,
Rod
PS: I've also tried to install the Iphone configuration utility however I don't know how to access the profiles on the phone, anyone can help with this so I can try the profile I've created?
I don't think it is going to work because the options available on the configuration utility are basicly the same available on the Iphone itself.
Anyone has any sugestion on how to solve this problem??? Thanks very much.

Sun Mar 28 06:02:24 unknown Preferences[292] <Warning>: wifi handler: (null)
Sun Mar 28 06:02:27 unknown kernel[0] <Debug>: AppleBCMWLAN::setASSOCIATE() [configd]: lowerAuth = AUTHTYPE_OPEN, upperAuth = AUTHTYPE_NONE, key = CIPHER_NONE, flags = 0x0
Sun Mar 28 06:02:27 unknown configd[22] <Error>: WiFi:[//////////////////>: Failed to associate with Internet: 5
Sun Mar 28 06:02:27 unknown kernel[0] <Debug>: AppleBCMWLANJoinManager::join(): No such network: "Internet"
Sun Mar 28 06:02:27 unknown Preferences[292] <Warning>: WiFiManagerAssociationCallback: err(5), err(00000005)
This is what I get on the Iphone configuration utility debug console. I edited out just a couple of numbers in case this is sensitive information the company wouldn't want me to share.
Message was edited by: F-22

Cannot setting up my Cisco router on maverick

Similar Messages

Maybe you are looking for