Cannot surf internet with WRT54G v5 on Windows Vista RTM x64

Hi, I have a Linksys WRT54G v5 router with Firmware Version: v1.01.1, Nov. 10, 2006. On Windows Vista x64 I Network conections says that I have Internet access, as a matter of fact Windows Update works fine and downloads some update without any problem.
I tried on two onboard network cards thai I have on my MSI K8N Neo2 Platinum: Nvidia NForce 3 and Realtek RTL8169/8110 Family Gigabit Ethernet NIC. I tried also installing a PCI Realtek network card and no luck at all.
The thing is IE7, MSN, and any application that tries to access Internet cannot connect. IE7 says "address invalid". However on IE7 64 bit surf internet perfectly, everything else fails to surf.
Same router is working fine on Windows XP x64 Edition and 32 bit.
Any ideas would be appreciated.Message Edited by Hernan on 12-23-200610:20 AM

Hi, well check whether after installing the drivers for the Ethernet card whether the pc picks up an IP address. You can check it from start > run > cmd and then ipconfig. If you are unable to pick up an IP address then try to lower the card speed
If still unable to get it working then check with the Microsoft whether the cards do support vista or no.

Similar Messages

I cannot sync to itunes on my computer (Windows Vista 32 bit) with my mini conected.

I cannot sync to itunes on my computer (Windows Vista 32 bit) with my mini connected. What should I do?
My Mini will not boot up. I tried holding both buttons down. I got a "connect to itunes" message. I connected. and nothing happens.

Hello there Chess-ster,
If I understand correctly your iPad mini is not being recognized in iTunes on your Windows Vista PC. I would recommend you use the troubleshooting in the following article:
iPhone, iPad, or iPod touch not recognized in iTunes for Windows
Start with these steps and work your way down as needed:
Restart
Turn off your computer and your iOS device, then turn them on again.
Update your computer
Check to make sure that you've installed all required updates for your computer.
Update iTunes
Check that you have the latest version of iTunes installed on your computer.
Check the USB cable
Verify that the 30-pin to USB cable or Lightning Connector to USB cable is free of debris and not damaged. If another cable is available, test with that cable instead.
USB cables that are bundled with third-party products or accessories might work only to charge those products and might not transmit data. Also, if you're using a third-party case or extended battery pack, try removing the case and connecting the Apple-supplied USB cable directly to your device.
Thank you for using Apple Support Communities.
Cheers,
Sterling

Right-click with 2 fingers on Windows Vista taskbar and nothing appears

I just updated my Bootcamp to 2.1, I thought it would solve my problem
"Right-click with 2 fingers on Windows Vista taskbar and nothing appears" but I still have this problem, I cannot right-click on my windows vista at all.
though, right-click on the notification area works.
right-click = pressing the trackpad with 2 fingers.

Now I have figured out I have to use 3 fingers instead of 2 fingers.
but in the BootCamp Control Panel there is an option that says
* Use 2 fingers for right-click

After uninstalling iTunes and re-installing, I cannot download the update. I have Windows Vista.

After uninstalling iTunes and re-installing, I cannot download the update. I have Windows Vista. Should I un-install again, and if so, where are the instructions for windows vista?

Have you tried to use another browser?
This may help you out -> iTunes: Downloading iTunes for Windows using Internet Explorer

Hey, I'm doing some cross browser testing and i want to know Is there any difference between the behavior of Firefox in an operating system 64bit & operating system with 32bit. (like windows7/windows vista...)

''duplicate of https://support.mozilla.com/en-US/questions/905881''
Hey, I'm doing some cross browser testing and i want to know Is there any difference between the behavior of Firefox in an operating system 64bit & operating system with 32bit. (like windows7/windows vista...)

Hi Kossa,
You can also check if the issue occurs in
Clean Boot. If the issue disappears in the Clean Boot environment, you can continue to narrow down which entry is causing the issue.
Besides, uninstall it and re-download
a fresh copy of FireFox to check the result. If the issue still exists, create a new user account to see if it occurs.
If the issue persists, you can contact Mozilla Support directly and use Internet Explorer (IE) during the time.
J
Please Note: The third-party product discussed here is manufactured by a company that is independent of Microsoft. We make no warranty, implied or otherwise,
regarding this product's performance or reliability.
Regards,
Linda

Captivate is not compatible with Windows Vista RTM

I can confirm that Captivate 2 is not compatible with Windows
Vista (RTM Final MSDN). I have been testing it on several systems
with various versions of Vista. It had partial success with RC2,
but with RTM it crashes quite frequently (when vista is drawing new
windows). I can't tell however if captivate is directly responsible
or if it is perhaps an incompatible version of Flash (current using
latest version 9 beta) that is to blame. However, since Vista is at
RTM then I would say that it is now the responsibility of Adobe to
fix the compatibility issues with a new update. Technically vista
is not due to domestic market until january 07, however businesses
will be able to purchase vista in only two weeks, and as Captivate
is generally used for business/training use i would certainly think
that it should be of high importance that these issues are
resolved.
Can anyone else comment on their experiences with Captivate
and Vista?

Hi cptv8
I appreciate your taking the time to report back your
findings about Vista. Perhaps it will be helpful to those that are
early adopters.
You stated:
Technically vista is not due to domestic market until january
07, however businesses will be able to purchase vista in only two
weeks, and as Captivate is generally used for business/training use
i would certainly think that it should be of high importance that
these issues are resolved.
You have a valid point. However, you are making it in the
wrong venue. How? Well, Adobe doesn't normally make it a habit of
visiting the peer-to-peer support forums. This means users
supporting users. If you are concerned that Adobe is aware of this
issue, you should really consider using a different channel. The
Wish Form. And you can easily get there by simply
clicking
here.
Now I don't claim to be a guru of anything in particular, but
it seems to me that businesses are very slow to adopt things. They
tend to take a very pragmatic and slow approach. Many are just now
making the leap to XP! So I'm guessing that Vista will be slow to
gain ground. I'm also confident that the Captivate team is well
aware of the Vista issues and will be addressing them as best they
can.
Sincerely... Rick

IPhone 3G 2.1 connection error with iTunes 8 on Windows Vista Enterprise

I was previously able to connect my iphone with my work computer (Windows Vista Enterprise) and it would recognize my phone. However, since I updated my iphone to version 2.1, it will not recognize the phone and gives me the following error message:
"iTunes could not connect to the iphone because an unknown error occured (0xE8000024)."
I am able to connect my phone with version 2.1 to my home computer running Windows XP SP2.
Any idea what may be causing the connection error in Windows Vista?

Hey TranceCadet,
This could be caused by a USB connection issue.
Make sure the iPhone is directly connected to a high speed USB port on the PC and not plugged into a hub, monitor, or keyboard. Disconnect any other USB devices, other than the keyboard and mouse.
This article has some general USB troubleshooting tips: http://support.apple.com/kb/TS1286
You may also want to disable or reconfigure any security software. This article will walk you through putting the PC in a selective startup mode, which will bypass most application conflicts.
http://support.apple.com/kb/HT2292
Jason

Error with Contribute 3 on Windows Vista

Hi
With Contribute 3 on Windows Vista, does anyone know if
anything can be done about the following error:
Error 1904.Module
C:\Windows\system32\Macromed\Flash\Flash.ocx
Failed to register. HRESULT -2147220473. Contact
Your support personnel
MMxtp has stopped working
A problem caused the program to stop working correctly.
Windows will close the program and notify you if a solution
is available.
Many thanks
lukaro

I've got the same problem. Adobe support are hopeless since
they bought Macromedia. "We don't support Contribute 3 any longer.
You'll have to upgrade to CS3". Downloaded CS3 trial. Same
problems. "Sorry, we don't support trial versions of products" What
a bunch of wankers. How the hell do they expect anyone to buy their
products if 1. they don't work and 2. they don't support them. I'll
find something else to buy from now on.

HT1178 Can the time capsule be used with a pc running Windows Vista , 7 or 8 as a backup drive

Can the time capsule be used with a pc running Windows Vista , 7 or 8 as a backup drive. If so what software do I need to buy?

Can the time capsule be used with a pc running Windows Vista , 7 or 8 as a backup drive.
Yes, on XP, Vista and 7. Have not tried 8.
If so what software do I need to buy?
Genie Timeline Pro does a very nice job...and it is similar to Apple's Time Machine. It's not cheap though. Check with the Genie folks for more info and compatibility with Windows 8.
Genie Timeline Pro | Overview | Time Machine Backup Software for ...
Other users may have some other suggestions.

Hey, I'm doing some cross browser testing and i want to know Is there any difference between the behavior of Firefox in an operating system 64bit & operating system with 32bit. (like windows7/windows vista...) Thanks,

Hey, I'm doing some cross browser testing and i want to know Is there any difference between the behavior of Firefox in an operating system 64bit & operating system with 32bit. (like windows7/windows vista...) Thanks,

Hi O_H_I_O,
Have you got an error code ?
Considering it is a brand new machine ,please update the machines .To get a better performance of the machines ,we should always keep it up to date .
There is a possibility that the DVD/CD-ROm drives driver is old or has corrupted .Please open the device manager , update or reinstall the driver to have a check.
Apart from this ,we can run the built-in tool to a diagnostic :
Control Panel\All Control Panel Items\Troubleshooting\All Categories\Hardware and Devices
We also can run the following fixit tool to have a check.
Fix problems with CD or DVD drives that can’t read or write media
http://support.microsoft.com/mats/cd_dvd_drive_problems
Best regards

Connecting iPod Shuffle to Windows Vista RTM

Dear all, I'm having problems connection my great iPod Shuffle to my newly installed Windows Vista RTM.
When I connect the iPod it's is shown as a Device. But I cannot copy any files to the device. It "hangs" for a few minutes before it stops with an error message. "Could not actualize to device. Unknown Error (-50).
Any ideas what this could be? Or is iTunes just NOT "Vista Ready" yet?
Thanks
Simon

1) Check and see if it will sync under XP compatibility mode (right click the program, not the shortcut> click properties, there will be a compatibility tab). A popup may nag you about changing the compatibility, just ignore it for the time being.
2) Check your USB hardware drivers to have them up to date. Vista is one of the weirdest OS's I've been around lately that uses older (read: not native or "updated") drivers and messes up on them...
3) The iPod service might be misbehaving. You can restart it by going to start> right click my computer>
manage> services and applications> services> click iPod service> click restart service.
4) NT OS's (including Vista) tend to be "closed oriented" on bidirectional hardware access, so make sure you can connect to other devices as well.
So much for the rumored iTunes update with the "colored" shuffles... I guess that's for later...

Distribution of JRE on Windows Vista Ultimate x64

The automatic update of the JRE on my Windows Vista Ultimate x64 system often comes up saying a new update is available but then as soon as I go ahead to install it, the update tells me that the particular version of the JRE is already installed.
How can this automatic update bug for new JRE installations be fixed.

iTunes cannot work if Quicktime doesn't, so that has to be fixed first.
Have you ever installed any of the following:
ACE & K-Lite mega codecs package, QT alternative, Storm codec, WinAVI video converter
If so the must be uninstalled.
Then or if you don't have them then continue with this;
Download the version of QUicktime that does not include iTunes:
http://www.apple.com/quicktime/download/win.html
Remove Quicktime using the method for QUicktime in this article:
XP
http://support.apple.com/kb/HT1925
Vista
http://support.apple.com/kb/HT1923
When you get to the system32 folder, you can delete any file or folder with Quicktime in the name.
Restart your PC and then install the Quicktime you just downloaded.
Check to see if it works and if it does try iTunes.

Windows 7 RTM x64 Power Manager and switchable graphics not working

Installed Windows 7 RTM x64 on my T400. After windows update and installing Lenovo's drivers, everything is accounted for. ATI graphics works fine, and I can see the Intel graphics on the shortcut menu. I just cannot manually switch to the built-in graphics, nor did I see the Power Manager. What do I need to do? I have installed the drivers for the power management, even though on the list of driver on lenovo's webpage it says it's only for SL models.
Help would be appreciated.
Specs:
T400
LED
ATI/Intel switchable graphics
4Gb

Have you installed the Power manager http://www-307.ibm.com/pc/support/site.wss/WIN7-BETA.html#powm ?
And after that, make sure you have installed the right driver (the one for switchable graphics): http://www-307.ibm.com/pc/support/site.wss/WIN7-BETA.html#m8xswitch
Hope that helps.
I also have Windows 7 Professional x64 on my T400 and everything works fine (i only uses programs and driver from here: http://www-307.ibm.com/pc/support/site.wss/WIN7-BETA.html
T400 2767-AG8
Windows 7 Professional 64bit

Distribution of Java JRE on Windows Vista Ultimate x64

The automatic update of the Java JRE on my Windows Vista Ultimate x64 system often comes up saying a new update is available but then as soon as I go ahead to install it, the update tells me that the particular version of the JRE is already installed.
How can this automatic update bug for new JRE installations be fixed.

Uninstall the software cleanly via the "Add or Remove programs" panel, then run another install. The breakdown is in the licensing system, not the application itself. Do not run the clean scripts until you have attempted this. If it still fails, then indeed a call to Adobe tech might do wonders...
Beste Grüße
Mylenium

Active Protection System Fail On Windows 7 RTM x64

I have a ideapad u110 and installed 64bit windows 7 RTM...
After installing APS, windows 7 shows blue screen and going to restart...
How do i resolve this problem or how can i find correct driver for windows 7 rtm x64?

When i try to install this driver "http://www-307.ibm.com/pc/support/site.wss/WIN7-BETA.html#tvap", installer shows "This sistem does not support Active Protection" alert. I have a ideapad u110 notebook..

Cannot surf internet with WRT54G v5 on Windows Vista RTM x64

Similar Messages

Maybe you are looking for