Cannot trace to hosts on ISR's using FW feature set

The issue is that we can trace between networking equipment on tunnels involving the ISR routers using Firewall feature set, but we cannot trace to hosts. For example from (US)AS1, I can trace to (UK)CS1's 192.168.1.2 ip address, but not to host that I find in the arp table for that vlan. I have added ICMP TTL exceeded and TTL time-outs to the ACL's, but it still does not work. Any helf would be greatly appreciated

Elijay, You stated that you are using ISR's. Are you perhaps running inspection? If so, you may want to check your ICMP rules for router-traffic and timeouts. You may want to increase the timeout setting.

Similar Messages

I do not fully understand how to use the "Feature Sets" of "General 1" through 5

I recently upgraded and aparently the printer driver was included in this. When printing through Photoshop Elements 10 a new drop down menu appears for printing with my Epson Stylus Photo 1400. I now have "Printer Features" and when that is selected from a drop down menu "Feature Sets" appears with "General 1" through 5 as drop down menu items. I can not find a user manual for operating all the options I now have. No matter what combo I set up however, my prints have a band in them. The printer now prints an inch of the image, runs the printer heads over the paper 4 times and scoots the paper forward an inch to repeat. Its this part of the print that gets the band. Its as if I am printing on regular paper when in fact it happens with both the matt and glossy. I select the right paper options (you have to select it in 3 different places) and yet the banding continues. PLEASE HELP ME.

I recently upgraded and aparently the printer driver was included in this. When printing through Photoshop Elements 10 a new drop down menu appears for printing with my Epson Stylus Photo 1400. I now have "Printer Features" and when that is selected from a drop down menu "Feature Sets" appears with "General 1" through 5 as drop down menu items. I can not find a user manual for operating all the options I now have. No matter what combo I set up however, my prints have a band in them. The printer now prints an inch of the image, runs the printer heads over the paper 4 times and scoots the paper forward an inch to repeat. Its this part of the print that gets the band. Its as if I am printing on regular paper when in fact it happens with both the matt and glossy. I select the right paper options (you have to select it in 3 different places) and yet the banding continues. PLEASE HELP ME.

Dbms_monitor.SERV_MOD_ACT_TRACE_ENABLE cannot trace service in job class

Hi All,
I have a issue about dbms_monitor.SERV_MOD_ACT_TRACE_ENABLE. It can
trace sqlplus query. But it cannot trace service in job class.
I am appreciated if anyone can help.
Below is test steps
1. add service
srvctl add service -d rdb -s oltp -r rdb1 -a rdb2
2. startup service
srvctl start service -d rdb -s oltp
3. using service in tnsnames.ora
oltp =
(DESCRIPTION =
(LOAD_BALANCE = ON)
(FAILOVER = ON)
(ADDRESS = (PROTOCOL = TCP)(HOST = rdb1)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = rdb2)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = OLTP)
(FAILOVER_MODE =
(TYPE = SELECT)
(METHOD = BASIC)
(RETRIES = 20)
(DELAY = 1)
4. open trace
dbms_monitor.SERV_MOD_ACT_TRACE_ENABLE('oltp');
5. run one query and check trace file
sqlplus /nolog
conn sys/sys@oltp as sysdba
select * from test;
in $ORACLE_BASE/admin/rdb/udump/rdb1_ora_22960.trc
There is the query: select * from test
6. create job class with service
BEGIN
DBMS_SCHEDULER.create_job_class(
job_class_name => 'OLTP_JOB_CLASS',
service => 'OLTP');
END;
7. create job
BEGIN
DBMS_SCHEDULER.create_job (
job_name => 'my_job',
job_type => 'PLSQL_BLOCK',
job_action => 'insert into test values (sysdate);',
start_date => SYSTIMESTAMP,
repeat_interval => 'FREQ=MINUTELY; INTERVAL=10;',
job_class => 'OLTP_JOB_CLASS',
end_date => SYSDATE + 7,
enabled => TRUE,
comments => 'Job linked to the OLTP_JOB_CLASS.');
END;
8. very result the job
select to_char(c1, 'YYYY-MM-DD HH24:MI') from test;
2010-05-16 17:17
2010-05-16 17:27
9. check trace file
in $ORACLE_BASE/admin/rdb/udump/ directory, there is no query like
insert into test values (sysdate);
Thanks in advance
Jacky

Thank you.
I see that we can use alter session to enable trace. But I don't want to add this kind of query into job. It is not convenient to do performance.
I want enable trace for the service 'oltp', and I can get trace files for all queries including job class.
Thanks for your suggestion, I am using sys as test on test db.
Thanks
Jacky

I am getting error like "nca_connect_server: cannot communucate to host "

I am getting error like "nca_connect_server: cannot communucate to host " while replaying my script through Loadrunner 9.1
virtual User Script started
Starting action vuser_init.
vuser_init.c(12): nca_set_connect_opt("SCALE_INFO")
vuser_init.c(16): Error: nca_connect_server: cannot communicate with host
PLease give me some solutions.
you can post me in my email id: [email protected]

Hi,
Please see if (Note: 376631.1 - Forms Server Loadbalancing Using Metrics Server Client Not Working with Mercury Loadrunner) helps.
Regards,
Hussein

NWDS Webdynpro deploy: Cannot login to the SAP J2EE Engine using ......

Friends,
I am getting the following error while deploying a web dynpro application through NWDS.
Aborted: development component 'WebDynpro_ErrorBehavior'/'local'/'LOKAL'/'0.2007.05.29.17.02.04'/'1':Cannot login to the SAP J2EE Engine using user and password as provided in the Filesystem Secure Store. Enter valid login information in the Filesystem Secure Store using the SAP J2EE Engine Config Tool. For more information, see SAP note 701654.com.sap.sdm.serverext.servertype.inqmy.extern.DeployManagerAuthExceptionWrapper: Wrong security credentials detected while trying to obtain connection to the J2EE Engine. (message ID: com.sap.sdm.serverext.servertype.inqmy.extern.EngineApplOnlineDeployerImpl.checkLoginCredentials.DMAUTHEXC)
I get this error after I supply the SDM password which NWDS asks before deploying.
Can someone guide?
[email protected]
Thanks

In the additonal error log it says-
Unable to compare host[px1db] and host[x900704] Throwable: java.net.UnknownHostException Throwable message: x900704: x900704
where px1db is my portal server and x900704 is my localmachine name.
I dont know why it says so ...In NWDS i have configured only px1db.
any thoughts.
Vinay

Cannot find PPoE host, can connect to router but not internet

I've been having trouble since I tried using the router. At first, I had no security, then I set up the security and couldn't connect to the router. That finally solved, sometimes when trying to connect to the router, I get the message cannot find PPoE host. But, my connection continues to show that it is strong in the bar at the top.
So, I try to get on the internet -- Safari, Firefox -- no go.
I run network diagnostics and the first three settings are lit, but the ISP, Internet and Server all show as failed.
I'm connecting via airport and a linksys router.
Thanks for any help

You'll have to go into your router's settings and make sure they're correct. When you connect to the internet through a router, the router has to be set up with the appropriate IP information (like setting it for PPPoE). If you have set your router up properly, then all you have to do is connect your Mac to it, either wirelessly or over ethernet, and it should auto-configure if you have your Network settings on "DHCP" (not the manual DHCP, though). You will get an IP address assigned by your router if it worked.
Hope that helps. Networking is always confusing.

Deployment exception : Cannot determine sdm host (is empty). error

Hi all,
i have installed the NW2004 s sneek preview. Trying to deploy a web dynpro application. Yesterday i was able to.
Today The deployment fails with the message
Deployment exception : Cannot determine sdm host (is empty). Please configure your engine/sdm correctly !
1) I am able to log on to SDM.
2) Can see SDM as running in sapmmc
2) the J2EE engine in the SAP netweaver developer studio shows SDM as green color
With parameters
state Running
Productive use No
Debug Off
Is there any problem with SDM. I have found quite a number of threads but knon could solve the problem. The problem looks more so complciated since I was able to deploy yesterday but am unable to today.
Appreciate any help
regards
Sam

Make sure that your NWDS has the j2ee engine linked to it. Under windows->preference->SAP j2ee engine.
If it is configured here, then you should be good. If it is still not working, try to reboot the j2ee engine and try again.
REgards,
Rich Heilman

Cannot determine sdm host

Hi,
I'm developiny webdynpro application usin NetWeaver Developer studio. While I deploy the error below appaers in log.
How can I solve?
Thanks.
Sep 16, 2008 12:49:52 PM /userOut/deploy (com.sap.ide.eclipse.sdm.threading.DeployThreadManager) [Thread[Deploy Thread,5,main]] ERROR:
[006]Deployment aborted
Deployment exception : Cannot determine sdm host (is empty). Please configure your engine/sdm correctly !

Hi,
Go to window ---> preferences
You will get a window opened in that
on the left hand side you have the SAP J2EE Engine option
double click on that
if you are using a server which is situated remotely then go for 1st option
Mesassage Server Host:--<Ip of the server>
Meassage Server Port :<port no>(Generally 3901)
If you have server installde locally on your system then go for the 2nd option
ther will be a browse you acn dind ur server and select that.
Thanks & Regards,
Lokesh

SFTP cannot connect to host

Weird issue here. Probably not DW's fault, but this seemed like the best place to start asking.
I'm using DW CS3 on a laptop running 64-bit Vista Ultimate, and it's connect via WLAN. On this machine I cannot connect to a site over SFTP. I get an immediate "Cannot connect to host" error. All normal FTP sites work fine. I also cannot connect to this SFTP site using CuteFTP on this machine.
However, on another PC, which is running XP Pro and is directly on the LAN (same network), I can connect to the same SFTP site successfully with DW CS3. The site settings are the same: I exported them from one machine to the other.
At first I thought it might be an issue with the Vista machine's Windows Firewall, but I disabled that, and got the same error.
I've Googled a bit for problems pertaining specifically to Vista and/or Wi-fi with SFTP, but so far no luck. I'd prefer to use the laptop as that is my primary work machine, but at least I can use the alternate PC to work on this site until I get this figured out.
Any ideas?
Thanks,
Greg

It definitely feels like a firewall kind of issue. Do you have a firewall set on either of your Dreamweaver installations? You can set this up in the Preferences panel (screenshot attached).
Hi Josh,
That's what I thought. So I temporarily disabled the firewall (Windows Firewall) on the laptop, but that didn't fix it. (The PC on which it does work has ESET's firewall.)
There's also a firewall on my D-LINK router, but its logs didn't show any blocking in real time.

FTP connection error w/DW5.5 - cannot connect to host

I was able to upload to my site on Monday, but the next day I started receiving the FTP error: cannot connect to host. It's not an issue with my provider and I can post using net2ftp.com and Filezilla, but not in Dreamweaver CS5.5.
I went to the manage site area and created an Adobe Test Server - I receive the same error.
I've studied several discussions, but I can't get this to work. Any new ideas?
Craig

I've been managing this site for a long time and update coupons on it approximately every 60 days. For some reason, I'm not having problems:
I opened DW CS5 today and made the changes necessary to update coupons. I was able to connect to the host server with no problem but most of my coupon images were not showing up. DW tells me I have 70 broken links, which can't be the case because I've reviewed them. Some links work and are the same as the broken links other than the file name. Unable to figure it out, I thought maybe restarting my Mac would help. However, upon logging back into DW, I am now unable to connect to the host server. I get an FTP error notice that the file doesn't exist or there is a permissions problem. Funny thing is, I can connect successfully if I test the connection through the Site Management window.
Has anyone else had this issue and if so, what is the solution? I feel like this is probably a simple fix, but I cannot for the life of me determine what it is! If anyone knows a solution, I'd really appreciate the help!
-Toni

"Cannot connect to host:" - Visual Administrator Error

Dear Experts,
I am unable to login using Visual administrator and the portal is also down. When i try to login using VA it gives the error
Cannot connect to Host:XXX and Port:XXXX
and when i try to call the portal url i get a page cannot be displayed error is displayed.
I have tried the following solution with out any luck.
Cannot startup visual administrator due to UME logon client details changed
/thread/731863 [original link is broken]
Cannot startup visual administrator due to UME logon client details changed
Very urgent. Please help ASAP
Thank you
Thanu

Hi Tomas Gustafsson,
Thank for the reply,
dev_jcontrol
dev_server0
dev_dispatcher
-> Displays the line as programming code
Hallo

Cannot connect to Host

Cannot connect to Host: ?
Posted: Apr 9, 2007 1:40 PM Reply E-mail this post
Hi
I have installed Sneak Preview in my system. When i am executing the Web Dynpro application its asking for SDM password. I have given the password which i am using for RemoteGUI.bat. I am able to login to RemoteGUI using the same passord. But when ever i have given the same password to the in SDM in Web Dynpro i am getting the following error
<b>
Error: Aborted: development component 'Sample'/'local'/'LOKAL'/'0.2007.04.08.19.37.49':
Caught exception while checking the login credentials for SAP J2EE Engine. Check whether the SAP J2EE Engine is up and running.
com.sap.engine.deploy.manager.DeployManagerException: ERROR: Cannot connect to Host: [compaq] with user name: [Administrator]
Check your login information.
Exception is:
com.sap.engine.services.jndi.persistent.exceptions.NamingException: Exception while trying to get InitialContext. [Root exception is com.sap.engine.services.security.exceptions.BaseLoginException: Cannot authenticate the user.]
(message ID: com.sap.sdm.serverext.servertype.inqmy.extern.EngineApplOnlineDeployerImpl.checkLoginCredentials.DMEXC)</b>
But my password is correct..
One more question.. How to create SLD in Sneak Previrew....
Please Help Me
Best Regards
Ravi Shankar B

Hi Ravi,
there could be two reasons:
1. Check whether you have made entry in Hosts file for your system hostname and IP address mapping. If not, you have to make entry in the host file.
2. Did you change the password of Administrator? If you have changed password of Administrator then, Open config tool and go to the secure store. Here, provide Same password of Adminsitrator in J2EE admistrator password field.
Password of Administrator in UME and in config tool should be same at all the time.
After doing this, try to deploy your application once again.
Regards,
Bhavik

[TimesTen]TT2778: Cannot infer type of parameter from its use

Hi,
On Timesten [[TimesTen 11.2.1.5.0 ] the below query results in error TT2778.
SELECT COUNT(1) cnt123 FROM DUAL WHERE %Var1String LIKE %Var2String,
Here both Var1String and Var2String are variables of String type.
Error Trace:
Caused by: java.sql.SQLException: [TimesTen][TimesTen 11.2.1.5.0 ODBC Driver][TimesTen]TT2778: Cannot infer type of parameter from its use -- file "saCanon.c", lineno 16963, procedure "inferExprTNLike()"
at com.timesten.jdbc.JdbcOdbc.createSQLException(JdbcOdbc.java:3287)
at com.timesten.jdbc.JdbcOdbc.standardError(JdbcOdbc.java:3436)
at com.timesten.jdbc.JdbcOdbc.standardError(JdbcOdbc.java:3401)
at com.timesten.jdbc.JdbcOdbc.SQLPrepare(JdbcOdbc.java:2285)
at com.timesten.jdbc.JdbcOdbcPreparedStatement.<init>(JdbcOdbcPreparedStatement.java:194)
at com.timesten.jdbc.JdbcOdbcConnection.prepareStatement(JdbcOdbcConnection.java:342)
Any pointer will be of great help.
Thanks and Regards,
Sud

While TimesTen has a high degree of compatibility with Oracle DB SQL there are still some significant differences due to them being essentially different products from a different origin. For example, Timesten is not really compatible with Oracle in terms of the bind-mode. Oracle uses late bind-mode and prepares queries on the first execution. TimeTen employs early bind-mode and TimesTen needs the data type before preparing queries. Because of this, the query you mentioned has different behavior in Timesten and Oracle.
You can work around this in TimesTen using somethign like the following:
SELECT COUNT(*) cnt123 FROM DUAL WHERE CAST(%Str1 AS VARCHAR2(1000)) like CAST(%Str2 AS VARCHR2(1000));
Chris

[Microsoft][SQL Server Native Client 11.0][SQL Server]The text, ntext, and image data types cannot be compared or sorted, except when using IS NULL or LIKE operator. 'Items' (OITM) (OITM)

Dear Experts,
i am getting the below error when i was giving * (Star) to view all the items in DB
[Microsoft][SQL Server Native Client 11.0][SQL Server]The text, ntext, and image data types cannot be compared or sorted, except when using IS NULL or LIKE operator. 'Items' (OITM) (OITM)
As i was searching individually it is working fine
can any one help me how to find this..
Regards,
Meghanath.S

Dear Nithi Anandham,
i am not having any query while finding all the items in item master data i am giving find mode and in item code i was trying to type *(Star) and enter while typing enter the above issue i was facing..
Regards,
Meghanath

Error in SQL Query The text, ntext, and image data types cannot be compared or sorted, except when using IS NULL or LIKE operator. for the query

hi Experts,
while running SQL Query i am getting an error as
The text, ntext, and image data types cannot be compared or sorted, except when using IS NULL or LIKE operator. for the query
select T1. Dscription,T1.docEntry,T1.Quantity,T1.Price ,
T2.LineText
from OQUT T0 INNER JOIN QUT1 T1 ON T0.DocEntry = T1.DocEntry INNER JOIN
QUT10 T2 ON T1.DocEntry = T2.DocEntry where T1.DocEntry='590'
group by T1. Dscription,T1.docEntry,T1.Quantity,T1.Price
,T2.LineText
how to resolve the issue

Dear Meghanath,
Please use the following query, Hope your purpose will serve.
select T1. Dscription,T1.docEntry,T1.Quantity,T1.Price ,
CAST(T2.LineText as nvarchar (MAX))[LineText]
from OQUT T0 INNER JOIN QUT1 T1 ON T0.DocEntry = T1.DocEntry LEFT OUTER JOIN
QUT10 T2 ON T1.DocEntry = T2.DocEntry --where T1.DocEntry='590'
group by T1. Dscription,T1.docEntry,T1.Quantity,T1.Price
,CAST(T2.LineText as nvarchar (MAX))
Regards,
Amit

Cannot trace to hosts on ISR's using FW feature set

Similar Messages

Maybe you are looking for