Cannot upgrade an AP1242 to LWAP using the upgrade tool 3.4
I have installed the tool on an XP laptop.
If I configure the tool to use an external tftp server then I get upgrade failed.
"Unable to Load the LWAPP Recovery Image on to the AP"
If I use the built in tftp server I get a msgbox with "C:\Program Files\Cisco Systems\Upgrade Tool\images\c1240-rcvk9w8-tar.123-11JX1.tar - LWAPP Recovery Image is not a valid one".
This is the log output
2011/03/15 15:52:57 DEBUG 10.10.10.5 Validating IP address
2011/03/15 15:52:57 DEBUG 10.10.10.5 Opening a telnet connection to the AP
2011/03/15 15:53:00 INFO 10.10.10.5 User has Full privilege
2011/03/15 15:53:00 INFO 10.10.10.5 Getting AP Name
2011/03/15 15:53:00 DEBUG 10.10.10.5 Verify if APs image is 12.3(07)JA or greater
2011/03/15 15:53:00 INFO 10.10.10.5 AP has 12.3(7)JA Image or greater
2011/03/15 15:53:00 DEBUG 10.10.10.5 Identifying the AP Type
2011/03/15 15:53:00 INFO 10.10.10.5 Term Length configured.
2011/03/15 15:53:00 INFO 10.10.10.5 Upgrade Tool supported AP
2011/03/15 15:53:00 DEBUG 10.10.10.5 Check whether AP has supported Radio
2011/03/15 15:53:01 INFO 10.10.10.5 AP has two radios
2011/03/15 15:53:01 DEBUG 10.10.10.5 AP has Supported Radio
2011/03/15 15:53:01 INFO 10.10.10.5 AP has Supported Radio
2011/03/15 15:53:01 DEBUG 10.10.10.5 Verifying Station Role
2011/03/15 15:53:01 INFO 10.10.10.5 Station role is Root AP
2011/03/15 15:53:01 DEBUG 10.10.10.5 Check whether AP has MIC Certificate
2011/03/15 15:53:01 INFO 10.10.10.5 MIC is already configured in the AP
2011/03/15 15:53:01 DEBUG 10.10.10.5 Getting Ethernet MAC address
2011/03/15 15:53:01 INFO 10.10.10.5 Hardware is PowerPCElvis Ethernet, address is 001f.ca28.973a (bia 001f.ca28.973a)
2011/03/15 15:53:01 DEBUG 10.10.10.5 Getting the Radio Status
2011/03/15 15:53:01 DEBUG 10.10.10.5 Entering Configuration mode
2011/03/15 15:53:02 INFO 10.10.10.5 Inside Shutdown function
2011/03/15 15:53:04 INFO 10.10.10.5 Shutdown the Dot11Radio1
2011/03/15 15:53:06 INFO 10.10.10.5 Shutdown the Dot11Radio0
2011/03/15 15:53:06 DEBUG 10.10.10.5 Getting Current System Time
2011/03/15 15:53:07 INFO 10.10.10.5 Updating the AP with Current System Time
2011/03/15 15:53:07 DEBUG 10.10.10.5 Entering Configuration mode
2011/03/15 15:53:07 DEBUG 10.10.10.5 Executing show run
2011/03/15 15:53:08 INFO 10.10.10.5 Saving the configuration into memory
2011/03/15 15:53:08 INFO 10.10.10.5 Getting AP Name
2011/03/15 15:53:08 DEBUG 10.10.10.5 Loading the LWAPP Recovery Image on to the AP
2011/03/15 15:53:09 DEBUG 10.10.10.5 Checking the Upload Status
2011/03/15 15:53:11 ERROR 10.10.10.5 Unable to Load the LWAPP Recovery Image on to the AP
2011/03/15 15:53:18 INFO 10.10.10.5 Dot11Radio0 is up now
2011/03/15 15:53:18 DEBUG 10.18.227.10 Opening a telnet connection to the Controller
2011/03/15 15:53:19 DEBUG 10.18.227.10 Telnet connection to the Controller opened
I see from other posts that JX image is required but it is not working for me. Can anyone help?
If I try to extract the tar file direct to flash I get this:
Loading c1240-rcvk9w8-tar.123-11JX1.tar from 10.1.1.1 (via BVI1): !
%Tar checksum error in fd 0
ERROR: Failed to extract from archive file tftp://10.1.1.1/c1240-rcvk9w8-tar.123-11JX1.tar
Maybe the files are damaged but I have dowloaded them all from cisco.com yesterday.
Similar Messages
-
Cannot upgrade an AP to LWAP using the upgrade tool on Windows 7
Hello,
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success. Help!
Thanks,
Kristen Woodard
Network Engineer IIAs an aside here, if the AP are newer, manufactured after 6/2005(Has a MIC and not a SSC), you can do a normal archive download command to run the upgrade to the recovery image. Can even be scripted to run multiple times via shell/cron
HTH,
Steve
Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later. -
I have just upgraded to the new OS X V. 10.10.3 but cannot access my iCloud Drive documents using the resident Pages and Numbers software on my MacBook Pro. Help is needed to access those documents using the resident software on my MacBook Pro rather than the Beta software on iCloud.com.
I have iCloud Drive set on the Finder sidebar and use that to open the Numbers Spreadsheet on iCloud.
OSX 10.10.3
Best. -
I am already paying a subscription for Adobe Acrobat XI Pro Now it want me to buy when using the edit tool or even the tool to insert pages Never had that problem before??????????????
Acrobat Reader can't edit PDF files. Use Adobe Acrobat Pro DC.
-
I cannot shut dow my MacBook Pro using the apple icon (as it was suppose to be), actually I have to press and hold the on/off buttom. I have taken twice for Mac dealer and they did not solve the problem. What must I do? I would to remark that I have installed 2 antivirus and uninstalled one of them. Since then I have facing this troublesome issue. Thanks
Uninstall the other AV software. They are not needed. All they do is cause trouble like you are having now.
If you have been forcing the Mac to shut down with the power switch you may nave corrupted your disk. You should repair it with disk Utilty to remove any corruption the shutdwons may have cased.
Allan -
Please see the subject line thanks
I upgraded to 20gb iCloud but it isn't enough to back up. I get constant error messages saying there is no backup space and I've not been able to use the upgrade. Apple promised to refund then didn't. Please help is there anyway I can use this space?If you were told they would refund the price for the iCloud storage - Contact AppleCare and ask to speak with a senior advisor. Have the case number for the promised refund available.
If you are trying to update your device, but you don't have sufficient space to download and install the update, you need to delete content from your device. Buying storage in iCloud does not add space to the device which is what you need.
You can always update using a computer with iTunes installed - this method is faster, and will allow you to make a backup on the local computer (Local backups restore faster than iCloud backups).
HTH -
On my Iphone I have 1-Camera roll, two Photo Libraries, and 1 delete. I cannot get rid of the Photo albums off the phone. I cannot take things off my Iphone using the itunes because it doesn't pull the Iphone up.
Pat2006 wrote:
I cannot take things off my Iphone using the itunes because it doesn't pull the Iphone up.
Correct. You don't use iTunes to get photos off the iPhone.
See this -> http://support.apple.com/kb/HT4083 -
Using iPhone 3G ,Version 4.2.1,Modem Firmware 06.15.00, In this phone i was using Facebook upgraded app and Smart Sync App. Suddenly my sisiter reset all setings and now I can't use the upgraded facebook app, for smart sync is asking for IOS 4.3,Need help.
Thank you for the answers so far, but I'll make one correction: I said earlier that the Boston Globe website, boston.com, does not have a mobile site, and I would need to visit their regular website on my iPhone. Actually, I just found out that boston.com has a mobile site, so I'd obviously use that instead of the regular site. By doing that, I'd save a ton of data (I think). Does that change your answers?
-
I use photoshop CS3. Shortly, when I try to use one of the tools, they react only with the eraser. So I cannot use the other tools. I tried to reset in general preferences all warnings. Then I can use the tools again, but with the next picture I get stuck with the eraser again. What can I do? Joost van Santen
Have you tried resetting all tools?
-
I cannot use the type tool in Photoshop CC it goes black. Why?
I cannot use the type tool in Photoshop CC it goes black. Why?
What goes black?
What OS version are you using?
And have you updated your video card drivers from the GPU maker's website? (bugs in video drivers being the most common cause of display issues) -
HSL Panel. When using the targeted tool I cannot control individual colors in the photo. In Luminance the entire photo is changing not just one area?
Yes, that's the way it works. The target tool is simply a way to pick a colour to modify, but all colours like that one, no matter where they are in the image, will be modified.
Hal -
Using the upgrade option ...
I have already upgraded my MacBook to Leopard - I used the clean install option and backed up all my files ... my brother is now interested in upgrading but does not have the time to backup everything on his computer, if he uses the upgrade option will it keep all his preferences and everything? ... he basically wants to be able to install Leopard and then continue using his Mac without having to redo anything he already had setup on it (if that makes any sense), is that possible?
Machieu wrote:
I have already upgraded my MacBook to Leopard - I used the clean install option and backed up all my files ... my brother is now interested in upgrading but does not have the time to backup everything on his computer, if he uses the upgrade option will it keep all his preferences and everything? ... he basically wants to be able to install Leopard and then continue using his Mac without having to redo anything he already had setup on it (if that makes any sense), is that possible?
If you don't have time to make a full backup, you don't have time to install Leopard.
A backup takes less than an hour. A bad install takes forever to recover from without a backup.
People who don't have time may make mistakes. And never upgrade a system that you need on a day-to-day basis unless you really have the time. And a backup.
Theoretically, on a well taken care of machine, you can do a simple upgrade (I did 2 - one on each of my MBPs - but I still had a backup) and it might work. If it fails then the option is an archive and install but the archive will be over a failed install - it won't be a virgin archive. If that fails you have to do an erase and install and without a backup you have saved nada, zip, zilch.
There's an old saying that if you take a shortcut, leave plenty of extra time. -
I have Elements 9 Mac do I have to use the upgrade addition for Elements 10?
OK I am a little confused regarding my plugins installed in Elements 9 Mac after installing Elements 10 Mac. How do I get my plugins to work with version 10? Will this happen automatically after I install 10? I am using a full version of Elements 10 not an upgrade.
No. Regardless of whether you use the upgrade or the full version, each version of PSE is a complete, standalone program. You will need to reinstall third party content, although for actual plug-ins some people have had success in just making an alias of the plug-in folder from the older version and putting that into the plug-ins folder in the newer version. But layer styles, effects, etc must be reinstalled in the new version.
-
I have lost my iphone and now i cannot locate it even when i use the find my ipphone app
i have lost my iphone and now i cannot locate it even when i use the find my ipphone app
It may be off, out of battery power or no internet connection. The lower section of the following link has some other things you may want to do (change passwords, report to law enforcement and to your cellular carrier: If your iPhone, iPad, or iPod touch is lost or stolen - Apple Support
-
I have been a proud owner of Apple products for many years. However, this problem is very frustrating! Any help will be appreciated. I used the migration tool to transfer the contents of my old MacBook Pro to my new shiny MacBook Pro Retina! After migration finished I tried to access my new MacBook Pro retina. However, when asking me to log in it refuses to accept the passwords from either the new MacBook or the old one! I do not have the option of using my Apple ID either.... Please help! Unfortunately, I am past my 90 day Apple Support!!
Restart holding down the CMD+R keys, launch Disk Utility and erase the HD, quit DU, and restore the OS. On first boot, use the Setup Assistant to do the migration. Details in Pondini's Setup New Mac guide.
Maybe you are looking for
-
Can more than one apple id use apple tv
I have one computer I use my apple id and iTunes on, my husband uses an external hard rive connected to laptop for his id and our son uses the laptop with his id . We all have our own iTunes. We haven't quite got the hang if home sharing and I was th
-
Where can I get an OS 10.5 or higher for my iBook G4?
I have OS 10.4.11 on my iBook G4. I am trying to install a printer driver for a new home printer. The installer disk tells me I need an OS version 10.5 and above. Where do I get that version?
-
How to use Role Menu item in BI 7.0
Hi experts, From web applications desiger in version 3.5 we can use Role Menu item to access our querys easily. In version 7.0 this item has been deleted from standard items. How can we manage it ? Thanks a lot Best regards, Santi
-
Errors in impdp command on oracle 10g database
Hi, could you plz help me to solve below errors which are coming while doing import with impdp command in oracle 10g 10.1.0.4.0 os: Red Hat Enterprise Linux ES release 4 ORA-06502: PL/SQL: numeric or value error: character string buffer too small ORA
-
Hi, I'm very new in this SAP world. I downloaded the NSP to play with it a little bit but I didn't realize when my license expired. Now I cannot login in the system and the only available instructions I've found specifies to use a saplicene.exe progr