Cannot upgrade the firmware.

I am using a BEFW11S4 router Version 4. When I checked the site and after a full day of messing around I found that the problem I was having was covered in the latest update. I downloaded the bin file and tried the upgrade process from the router management. It failed. leaving the router still working but still with my original problem. Went to user groups and read what i could find. I turned off virus program, firewall and connected directly to internet to download bin file. (did this 4 times) tried again. failed. still did not upgrade the firmware and read more and downloaded the utility It could not access the router - Login failed. tried to login to router and logged in fine. spent another 4 hours trying to find any other suggestions either on the linksys site and in the forums and could not find anything. Keep in mind I have been using cisco products for about 20 years now and I am fully qualified Network technician. Please don't annoy me with any more simplistic suggestions I need a workable solution since I have about two or three hundred of these types of units out there. My interim solution was to go to staples and pick up a $49 Belkin router that works just fine. The solution suggested by the linksys person on the phone was to pay $29 to maybe resolve the issue. can anyone see the economics in that?
P.S. went to the lela download link in the message at the top of this forum. It says to download lela click here. Did so and got a really nice demo. there was no download. so if anyone knows where to download that it might be worth a try.
Message Edited by tekkiefirst on 07-17-2008 03:22 AM

Try upgrading the firmware of router ... reset it & reconfigure it ... if it works ... that will be fine if not ... then possibly the router is gone bad ...

Similar Messages

FAQ Broken: How do I upgrade the firmware on a WRT54G Wireless-G Broadband Router?

I tried to view the above question in the FAQ, but it goes to the answer for a different question.
I then tried "How do I upgrade the firmware on my router?" a little further down,
but it acts like I'm not authenticated, and won't accept my Linksys Forums e-mail address
and password. When I try the password recovery, it says my e-mail address is invalid.
Can someone please point me to instructions for upgrading the firmware on my WRT54G?
Specifically, someone told me that the router needs to be listening on the default 192.168.1.1
IP address, but mine is listening on 10.1.1.2. Do I need to change this just to flash new
firmware, because that will be a little painful.
Thanks,

Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - "Default Gateway of Your Router"...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
**To Check the Default Gateway of the router...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
**To all the above setting using the wired computer.

My iphone 4 when you upgrade the firmware on ios7.0.2 produced an error 3194

my iphone 4 when you upgrade the firmware on ios7.0.2 produced an error 3194 ... now my phone is not working ... every time an error 3194 ... I can not update ios and drop naturally I do not Pogue. hosts cleaned, cut off the antivirus ... did everything I recommend in this case ((what do I do? (
on other machines the same ...

Some additional suggestions here that may help if you haven't tried them:
http://support.apple.com/kb/ts4451
Regards.

I upgraded to OS Yosemite on my MacBook Air...and I cannot upgrade the Adobe Flash download that Adobe keeps asking me to download. I get the screen and when I click on the icon it just creates a new window but not download. Thoughts?

I upgraded to OS Yosemite on my MacBook Air...and I cannot upgrade the Adobe Flash download that Adobe keeps asking me to download. I get the screen and when I click on the icon it just creates a new window but not download. Thoughts?

I just tried the link and it is just fine. If the GateKeeper pops up then open Security & Privacy preferences, click on the General tab, set the last radio button to Anywhere.

SCCM 2012 R2 SQL Database Upgrade Fails : Setup cannot upgrade the ConfigMgr database. Contact your SQL administrator.

Hi Friends,
We have planned to upgrade our SCCM 2012 SP1 infrastructure to SCCM 2012 R2 so we have setup test environment to test SQL database upgrade before doing same in production.
But while testing SQL database upgrade on test machine, it is getting failed with below error.
ConfigMgrSetupWizard.log
ConfigMgrSetupWizard Verbose: 1 : Scripted setup failure handling callback called. Failure: 29.
ConfigMgrSetupWizard Verbose: 1 : Received error [Setup cannot upgrade the ConfigMgr database. Contact your SQL administrator.] from native code.
ConfigMgrSetup.log
ERROR: SQL Server error: [23000][2627][Microsoft][SQL Server Native Client 11.0][SQL Server]Violation of PRIMARY KEY constraint 'ContentDistribution_PK'. Cannot insert duplicate key in object 'dbo.ContentDistribution'. The duplicate key value is (921). :
tr_ContentDistributionNotification_insert
ERROR: Failed to execute SQL Server command: ~-- ~-- Rebuild ContentDistribution tables ~-- ~IF (EXISTS(SELECT TOP 1 1 FROM dbo.SMSData WHERE SMSBuildNumber <= 7900) AND dbo.fnIsSecondary() != 1) ~BEGIN ~ exec spRebuildContentDistribution
@TruncateTables=0 ~END
Failed to create process of SetupWpf.exe.
Can anyone please help to get this resolved.
Thanks.

We found out that there were duplicate entries in the PkgStatus_G and the PkgServers_G tables in the SCCM DB. We identified them, deleted them , and then we were able to run the /TESTDBUPGRADE command and it went through fine. We performed
all of this on a COPY of the PROD DB and then moved the changes in PROD. Hope this helps someone.
- Dave

I have an old iMac version 10. 4.11 and I have the iPhone 3GS which I cannot upgrade the latest applications I want to buy the iPhone 4S but I need to back up all the information on my iMac and move it to a different computer contacts songs etc which is t

I have an old iMac version 10. 4.11 and I have the iPhone 3GS which I cannot upgrade the latest applications I want to buy the iPhone 4S but I need to back up all the information on my iMac and move it to a different computer contacts songs etc which is the easiest way to do this

Glenn,
I tried upgrading to leopard, even bought the software and brought it home but it wouldn't let me. So i went back to apple, gave them the specifications of the machine and been told my machine is simply too old for leopard. This is incredible to me because it really isn't THAT old (i think just a little over 6 years maybe) and yet i'm left out on the curb when it comes to using newer apple products. I understand technology moves on but the mindset that i am supposed to dump a perfectly working machine after a couple of years or face not being able to use any other apple product is counter to what thought apple was about.

I have a WRT54G v8.1. I upgraded the firmware, and now it DOES NOT WORK.

I have a WRT54G v8.1. I upgraded the firmware, and now it DOES NOT WORK. It keeps telling me that this router is not supported. There is no firmware to roll back to. It worked fine until a power outage. HELP!

If your Internet Service Provider is Cable follow this link to configure the router.
If your Internet Service Provider is DSL follow this link to configure the router.

Why I cannot upgrade the macbook 5.3 at the operating system to the latest version it seem to only go at 10.5 max

Why I cannot upgrade the mac book 5.3 at the operating system, the actual ver. 10.5 and cannot upgrade to a newer version

Forgot to mention that in order to upgrade to 10.8 you must first upgrade to 10.6.8. Get it here and then run software update to get access to the App Store http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard

Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
Who can tell me what does this error message mean and how to elinate this error message ? also how to deal with 100% CPU utilization ?
Thanks.

Hello,
i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
i also have a could of questions if anyone can help
the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
thanks in advance.

MSI DR4-A,How do I upgrade the firmware? (How do I flash?)

I can't use my MSI DR4-A for anything now since i dont know how to upgrade the firmware (flash) can somebody please explain how to flash it better then the ReadMe file the lates update came with..cause i seriously don't understand the readme neither does any of my friends..so please help me someone...

I updated the Firmware yesterday, what I did was the following.
Downloaded the latest (2.50) firmware from the download page, and putted all the files (DVFLASH.EXE and 250D.BIN) on a floppy.
Went to Bootdisk.com and downloaded the win98SE OEM bootdisk (as suggested by others here) and ran the exe by using a second floppy.
Rebooted my pc with the newly created bootdisk in the floppy drive.
After a while you'll see the prompt.
Replace the bootdisk with the disk where DVFLASH.EXE and 250D.BIN is on and make sure the promt says A:\ (assuming this is your floppy drive).
Then type DVFLASH 250D.BIN
(also assuming the version is 250D.bin, which it is now atm).

T61p cannot upgrade HD firmware

When i make a CD for upgrade new firmware driver and tell me cannot find new firmware driver?
what is the problem about it?And how can i do?
Thanks!

When i make a CD for upgrade new firmware driver and tell me cannot find new firmware driver?
what is the problem about it?And how can i do?
Thanks!

After upgrade the firmware, it can't be initialize

Hi,
I use PCI-7344 and UMI-7764
and upgrade the motion software and firmware to 7.2 version
but I can't be initialize the motion card in MAX
the error code is -70038
由 ycw7 在 03-25-200601:53 PM 上編輯的訊息
====================
●LV Version：LabVIEW7.1
●OS：WindowsXP(SP1)
●Hardware：PCI-7344, PCI-6602, PCMCIA 6024E
Attachments:
error.jpg ‏122 KB

Hey ycw7,
After getting this error, I would recommend that you take the board out of the PC, uninstall the NI-Motion driver software, and make sure that any motion configuration files or any files regarding motion get deleted. Then do a reinstall of the NI-Motion 7.2, place the board back in the computer after the installation is complete, and this time try the board in a different slot, and see if you can initialize the board. If this doesn't work, then if you have another PC that you can install Motion 7.2 on, try it in another machine and see if you get the same error. If you still get this error, then you might want to try reverting back to an earlier version of NI-Motion, like 7.0, and see if you can get that to let you initialize the board. Finally, if none of these work, then you should contact National Instruments and work with them about what to do next. Let me know if you have any questions. Thanks, and have a great day.
Regards,
DJ L.

Error upgrading the firmware from 3.0 to ny version on WLC

Hi All,
Please help me on this issue:-
I am currently running 3.0 version on my WLC 4402 and i want to upgrade it to the latest versions. I am following the correct procedure mentioned in the cisco link but its failing.
The error is TFTP Path is getting as:c:\temp\/ error and the firmware is not getting uploaded,
Plz see the snap shot and let me know what am i doing wrong.

I forgot to add, please read the release notes to see which version you can upgrade to as this will have to be done in stages.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805f381f.shtml

Need Help!!! Cannot upgrade EFI firmware 1.5.1

My Boot ROM Version is: MBP31.0070.B02
I followed every step and up to click the shut down button and i clicked it then received a message:
"An unexpected error occurred (28 : 3).
Your firmware can not be updated."
Any ideas how to fix it? Thanks.
PS. I cannot run bootcamp, neither. It said i have to update my boot rom version, can anybody help me at this problem, also? I tried all the EFI firmware update from 1.2 to 1.4 and it said my MBP dont need this update.

Yes, it does indeed appear that it is GUID. Curiouser and curiouser.
OK, so let's check over things again.
THe drive you are booted from when trying to install the Firmware is the internal drive on the MBP.
It is using the GUID partition scheme.
What else can it be here?
1) Your internal drive has a single partition, formatted as HFS extended( journaled) on it at the present time?
2) You don't have any other devices (external FW or USB drives, external keyboards etc) attached at the time when you attempt the update (the power adaptor is the only that that should be attached to your MBP when you do a Firmware update)?
3) You are using the correct updater (http://support.apple.com/downloads/MacBookPro_EFI_Firmware_Update_1_51) . (It may be worth downloading a fresh copy just in case).
Cheers
Rod

My airport extreme is saying that I need to upgrade the firmware to 7.3.1 but I can't find where to get that download.

I bought a new airport extreme on ebay and it works but as soon as I hooked it up it says I need to update the firmware to 7.3.1 and gives me a link to go to but it won't give me an option for that update. I tried the other updates that it gives an option for but none of them work. Help!

OK, if your Extreme is an original "round" 802.11b/g model you need AirPort Utility 5.6. The problem with that version is that Mountain Lion will refuse to let you install it. Other than that, there is nothing wrong with using AirPort Utility 5.6 and your older Extreme should work just fine with your new MacBook.
This dilemma is easily solved. You simply need to extract the app from the installer package using a package extractor like Pacifist or unpkg. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
When the AirPort Utility .dmg file finishes downloading, open it to expand and reveal the AirPortUtility56.pkg package installer file.
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
Open Pacifist and from its File menu, navigate to the package and open it.
Click the "reveal triangles" until you see AirPort Utility 5.6.app:
Select it and then click Install from Pacifist's toolbar. It will then be installed in your Utilities folder, and you can quit Pacifist.
Mountain Lion will not allow you to delete its existing version of AirPort Utility. Just ignore it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist. Launch AirPort Utility 5.6 and firmware upgrade options for your older Extreme will be available.
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder instead of resorting to the above procedure. It will run without complaint. It is only the package installer that is the problem.
If you have an older computer with a version of AirPort Utility earlier than 6.0, you can administer it that way as well.

Cannot upgrade the firmware.

Similar Messages

Maybe you are looking for