Cannot use charging cable with bumper.

I just got my bumper for my new phone and am having issues trying to connect the charging cable that was supplied with the phone. If I push the cable firmly into the phone it shows as charging, but the minute I take my hand off it stops charging.
It seems that the cutout in the bumper is slightly too small to allow the connector to pass through it and the cable's clips do not lock the cable into the phone.
Has anyone else experienced this problem?

Those of you needing a good case look at Incase Slider and Incase Snap Case. I have both and they are great. Below link is my review on the slider.
http://discussions.apple.com/message.jspa?messageID=12069793#12069793
Herbie_K wrote:
Your review of the bumper was right on the money. I'm waiting to see the new Casemate Barely-There II case. My wife has one for her 3G and it is a very nice case.
Tonight I discovered the headphone issue when I tried to plug in a Monster cable to listen to iTunes on my stereo. The Universal dock stopped holding up the phone. Had a real time with the jack but finally got it to play.
Still virtually no cases out there for the 4, none in any Apple store I visited. C'mon Apple, if you're going to build a flawed phone that requires a case, you better deliver a case that works!

Similar Messages

HT204291 Help! I cannot see the Airplay symbol on any of my devices anymore! I have tried following all guides and troubleshooting, but to no avail. Just cannot use the AppleTV with any of my devices.

Help! I cannot see the Airplay symbol on any of my devices anymore! I have tried following all guides and troubleshooting, but to no avail. Just cannot use the AppleTV with any of my devices.

Thanks for the link. It didn't work at first on any of the devices but then I decided to enter a manual DNS instead of an automatic configuration. Then followed the steps again from your link and it worked.
It is not stable though as I need to reset the device for it to see the airplay. But when it is connected it stays connected for 30 minutes approx.
Any other suggestions to keep it stable would be fantastic but at least in the meantime I have a workaround.
Thanks

I connected my iPod Touch to a stereo system phono input using a cable with stereo jacks (red and white) on one end and that plugs into the iPod's headphone jack. The problem is that the sound is extremely muffled and bass-heavy, with little treble.

I connected my iPod Touch to a stereo system phono input using a cable with stereo jacks (red and white) on one end and that plugs into the iPod's headphone jack. The problem is that the sound is extremely muffled and bass-heavy, with little treble. I have to turn the bass control on the stereo receiver to pratically zero in order for the sound coming through the stereo to be acceptable. Is there a setting on either the iPod or the stereo that I need to change in order to fix this?

The phono input is for a phonograph. The iPod does headphne output is not that same as a phongraph output. Does th stero have an AUX input? That should be compatible.

I cannot use downloaded ringtons with my Contacts.Ringtones downloaded by programme Ringtones

I cannot use downloaded ringtons with my Contacts.Ringtones downloaded by programme Ringtones

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

"You cannot use this application with this version of OS X"

Hi,
I'm getting this message when I try to open .AVI files that I uploaded from my digital camera, but I'm posting it here instead of in the Quicktime section because I believe that the cause of the problem is more general. When researching this problem, I looked at the info panel for these .AVI files, and the app listed to open them was "Quicktime Player (default) (7.1.3)". But the actual version of Quicktime that I have installed is version 7.4. If I set the file's "Open With" app to be "Quicktime 7.4", it opens fine, but the "Open With" app reverts back to "Quicktime Player (default) (7.1.3)", making the problem come back. I've also noticed that if I right-click on other apps (a PDF file, for example), and choose "Open With" from the popup menu, that I see other versions of apps that no longer exist on my machine (Safari 2.0.4, for example). I think that files associated with these older app versions may be the cause of many of the "You cannot use this application with this version of OS X" issues that have been reported here. My question is where is this list of "installed" products maintained in OS X, and is there a way that I can edit it to remove those product versions that no longer exist on my system. In my particular instance, I'd like to remove "Quicktime 7.1.3" which should allow me to set the associated app for my .AVI files to be Quicktime 7.4 with no possibility of the association reverting to an earlier version that's not only incompatible with Leopard, but also not installed on my system.
Thanks,
Ken

When you associate a file with an application, are you then clicking the "Change All" button? You can rebuild the LaunchServices database. Evidently the location of the command and the database have changed slightly in Leopard from what they were in Tiger. See this thread for the updated instructions:
http://discussions.apple.com/thread.jspa?messageID=5730491
Also, make sure you don't have the old applications archived somewhere. I've been astonished in the past at just how enterprising the system can be in finding some program squirreled away in an obscure backup folder and listing it as an option to open something.
Francine
Francine
Schwieder

Cannot use push notification with Whatsapp

Cannot use push notification with Whatsapp and pop up "Connect iTune for Push Notification" when open Whatsapp

http://www.whatsapp.com/faq/en/iphone/20950116
 Jackson

Using an OEM charger cable with 4S and at 46% charge started making a bing,bing noise and stopped charging......why???

I have an iPhone 4S.I have been using an OEM charger to charge the thing up and early this morning it started to 'ping'and all night I was getting a ping,ping,ping.It stopped chartgbing at 46% and then died to 30% of charge before I found the old original charger cable and so far its all OK....Can some one explain why this would have happened or occured and have they had the same problem.
I am debating whetnher to order anew lead to charge the thing.....
Assistance will be appreciated.

I have an iPhone 4S.I have been using an OEM charger to charge the thing up and early this morning it started to 'ping'and all night I was getting a ping,ping,ping.It stopped chartgbing at 46% and then died to 30% of charge before I found the old original charger cable and so far its all OK....Can some one explain why this would have happened or occured and have they had the same problem.
I am debating whetnher to order anew lead to charge the thing.....
Assistance will be appreciated.

IPod error sign that shows ipod end of charging cable with an arrow

my third generation iPod just got restored and now it shows the ipod end of the charging cable that goes in the bottom of the ipod with an arrow pointing to the left.
When plugged in it shows the apple icon then this error icon and shuts itself off
What do I do??
Please help me

Connect the iPod to a 6-pin FireWire port on a computer, the iPod power adapter, or a car adaptor. Until you've done one of these things, the iPod will not be able to complete the restore process, and you can't use it again until it's done.
(15557)

Is it possible to use a cable with two headphone jacks on either end and an electric guitar adapter to record in Garageband?

Hey everyone,
I got my Macbook Air (Mid 2013 model) last month and I want to record my acoustic-electric guitar on Garageband (which came with the Air).
I don't want to buy a guitar that has a USB. I have a cable with a 3.5 mm headphone jack on both ends like the one pictured here on this website http://www.bestdealaz.com/item.php?id=628 (i didn't buy it from this site though).
I connected a 6.3 mm guitar adapter (http://www.ebay.com/bhp/headphone-guitar-adapter) to this cable. Then I connected one end of the cable to my guitar and the other end to the Headphone/Microphone jack on the left side of the MBA.
I saw how other people were saying to go to System Preferences / Sound and then change audio output to audio input.
I can't do that. I tried.
Please help!
Thank you.

Hello Massimo Pascucci,
The issue that you are facing when creating an endpoint with internal loadbalancer is the limitation of not allowing same ports to be listening under a single cloud service. This reason for this is that there is a limitation of only one private IP (Also
known as the Internal load balanced IP) per cloud service.
There is also a limitation on the Internal load balancer more than one port to be published per load balancer:
You can leave your feedback by following the link below:
https://social.msdn.microsoft.com/Forums/en-US/1805c5a0-3906-4cd6-8561-9802d77e0ae5/is-it-possible-to-use-both-an-ilb-and-an-elb-listening-on-the-same-port-in-the-same-azure-cloud?forum=WAVirtualMachinesVirtualNetwork
Refer to this article for more information on Internal load balancer:
http://azure.microsoft.com/blog/2014/05/20/internal-load-balancing/
Thanks,
Syed Irfan Hussain

HT6154 I tried to update software for my iphone...now I cannot use it-stuck with an itunes logo and the plu..when I go to itunes to look for my name iwth device there is nothing

I tried to update my iphone,,ran downstairs ot garden since it took 30 minutes. I cam e back with an itunes logo and plug on the front cannot use my phone or call it....apple's store in tampa is close...I will probably get in a car accident on my way to the store 1 hour and 30 minutes away after I get pulled over for speeding after I get a flat tire(;

Hello hstacy
Check out the articles below to troubleshoot issues with resolving issue with issues updating your iPhone. If you are having issues with it not being seen, pick one of the two articles that goes with the type of computer you have.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/ts1591
Regards,
-Norm G.

Cannot Use Rollover Functions With Templates

I'm surprised that you do not hear anything about this, but
if you create a template in Dreamweaver 8, your buttons will work
but you cannot use rollover effects. That stinks! Does anyone know
of a hack, plug in, etc. to get around this bug? It seems like i
always find the bugs for some reason.
Thanks for any help.

They have always worked in every version from DW2 through the
current CS3,
which is what I am using.
Show me a child page where they are not working, please, by
posting a link
to one.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"dsmflash" <[email protected]> wrote in
message
news:fakq86$6a$[email protected]..
> Well, something must be up with my version of Dream 8
because mine do not
> work
> and I have created my temps to the letter. So what
version of Dream are
> you
> using and how do you get rollovers to work? How can a
rollover effect
> work
> when the template is locked?
>

Using audio cable with iPod

When I got my iPod, I bought a kit of accessories that included an AV cable, and audio only cable, etc. Since I have some yoga exercise videos on my iPod, I use the AV cable to connect the iPod to my TV so that I can do the practice. I've also done this for audio-only yoga practices by just connecting the audio plug of the AV cable (ie, instead of using both the audio and visual plugs).
So, what I'm not sure how to use is the audio-only cable. The one I have has plugs on either end that are identical, both with headphone symbols. So, yesterday I tried plugging one into my iPod, one into my stereo's headphone jack--it fit, but this didn't work, even when I turned my stereo to the AUX setting. Is it even possible for the stereo headphone jack to receive input coming in? Am I doing something wrong?
I'm sure this is a dumb question, but I'd appreciate any input!

Ya, going from headphone jack to headphone jack will not work as both are outputs.
The audio only cable is really made for things like car stereos that have a aux input jack of that type. For the home stereo you typically have RCA jacks (the red, yellow, and white style ones).
You can buy a cable with the 1/8" iPod headphone plug on one end and a pair of (red & white) RCA jacks on the other and use that, but you might as well just use the A/V cable you have an ignore the yellow RCA plug when using it for audio only.
Patrick

Cannot use isight camera with Windows 7 x32 on Macbook mid-2009

Very very weird,
it worked until bootcamp was upgraded mid next year.
I have been looking for a solution siunce then.
Wife is using the notebook and she is mad every time she is answering call from Skype or MSN Messenger she needs to reboot into Lion.
She uses Windows 7 x32 on bootcamp most of the time yet she cannot use the camera.
The camera shows grey and freezes wiuth busy mouse cursor.
booting intro Lion works so it is something with the drivers.
Can anyone help?
I have looking for months already and I did not see solutions...
Andrea

Issue Fixed.
BootCamp 3.2 - 3.3 breaks the functionality with Windows 7 at the latest patch level.
The fix has been:
upgrading OSX to Lion
Patch to latest release
Go To Boot Camp Assistant
Download Windows Support Files to Jump Drive (second option I believe it is)
Reboot into Windows 7
Run Setup - BootCamp 4.0 will install
Reboot
Launch Skype or MSN Messenger - ISight will magically work again!

Cannot use HP scan with 7520 on OSX Mavericks

I have added a new computer to the household---a 2014 macbook air. I currently use my 7520 to print and scan without any problems on our other home computer (2011 macbook pro). I just installed the latest drivers and software (for Mavericks 10.9) and software, and I can print just fine using any print dialog. I can also scan documents if I use Apple's built-in scanning software from the system preferences menu.
BUT: I cannot use HP scan at all! Every time I attempt to scan a document, it tells me a dialog that says:
"HP Photosmart 7520 series-AirPrint is currently unavailable. Please check if it is turned on and connected, or try again later."
I don't get it---I can connect and scan just fine using NON-HP scan software, and this is the latest software/driver kit. I really like HP scan for its wireless and editing abilities, and am very frustrated! How can I fix this?
Thanks!

SunShyne
I think that did it! I missed a step in your previous explanation. Will see if it holds. I'll report back here if it loses it again, bot all good for now.
Thanks

Cannot use Intel widi with my Satellite L50-A-11T

Hi,
I have a Satellite L50-A-11T and i've tried to use Intel widi with Windows 8.1 and doesn't work, it says that the system is not compatible.
With Windows 8 it was ok and worked fine, but in the instruccions for upgrading it said to remove Intel widi.
Why is that?
Thanks in advance.

You misunderstood this info.
Intel WiDi isnt supported in Win 8.1 on Toshiba notebooks BUT instead of Intel WiDi you can use Miracast.
But Intel WiDi is not Miracast.
Intel WiDi was developed by Intel.
Miracast is an standard supported by developed by WiFi Allianz and Intel is a part of this Allianz
Windows 8.1 as well as Android 4.2 support the Miracast standard.
But this does not mean that you can use it always you need the compatible hardware parts.
In case your TV would not support Miracast standard, you will not be able to use it

Cannot use charging cable with bumper.

Similar Messages

Maybe you are looking for