Cannot use the F1-12 functions on my Satellite C55-A-19K
Hello there
Satellite C55-A-19K have an keyboard drivers?
I cannot use the F1-12 functions and cannot get the wireless on since its on the keyboard...
Can some 1 help please?
Hi
The basic setting on these models is that the special functions on the [F1]-[F12] keys are used without [FN].
So for example activating / deactivating the touchpad is done from [F5] (not [FN] [F5])
It is also possible to change this behaviour. Setting the Function-keys to traditional mode in the BIOS will revert back to the keys used along with [FN].
So activating / deactivating the touchpad in traditional function key mode, requires [FN] [F5].
So be sure to check your function key behavoiur - if you have set it to use [FN] first or not.
And keep in mind that in case the current mode is not what you want, you may change it.
Hope this helps
BR Tom
Message was edited by: MannerhagenVPO
Similar Messages
-
My notification center (windows 7 64 bit) disappear from time to time, any idea?
When it disappears, I cannot use the special keyboard functions like sound,brightness...
Thanks!How is Acrobat 8 not fully Windows 7 compatible? I see discussions on this Adobe Community saying how Acrobat 8 does work on Windows 7 and with 64-bit. It appears that if Acrobat 8 is updated to the latest version, then this should fix AA8-Win7 issues. And I am at the latest AA8 version, 8.3.1.
And how are Acrobat 8 and Reader XI are not compatible? I have always had Acrobat and Reader installed on the same PC, without ever having any issues. And Adobe allows the installation of one after the other. So apparently Adobe allows them both to exist together. If they are incompatible, then why would Adobe allow them to exist together?
Anyway, I did uninstall the FileOpen Plug-in and the Reader XI, then reinstalled the FileOpen Plug-in. So now Reader is not installed and only Acrobat 8 is installed. I then tried to load the PDF file, but I still get the Acrobat 8 error described above. -
I just loaded Final Cut Pro onto a new computer and I cannot use the undo/redo function keys. Is there a problem with the software or do I have a setting set incorrectly.
When I go under edit, both undo and redo are grey so I cannot use. I also cannot use the short cut key.Undo/Redo is command and Z. Are you using a different keyboard layout than US English?
You can set the number of undos from the menu bar: Final Cut Pro > User Preferences > General.
This functionality is dependent on how much RAM is installed in your computer - setting a higher number of steps backwards will use more. How much do you have installed?
Undo/Redo is only available after you have done something to the media in FCP. It is not saved in your project file. Closing a FCP project will lose any saved undo steps, although you can still use one of the Auto-saves of your project file to go back. -
Just installed a HP Color Laserjet CM2320nf MFP printer, at the same time I upgraded to Lion. It prints fine, but I cannot use the scan functions. I downloaded the most recent driver! Any help would be appreciated.
HP says that the drivers for your all in one print/scanner are downloadable from apple. For the scanner to use preview. image capture or the scan icon from the print driver queue. I don't know how old your HP is, but I know that the newer Os from apple don't support a lot of older printers. You might be able find a third party driver that could work.
-
Suddently I cannot use the functions of my magic mouse
Suddently I cannot use the functions of my magic mouse (scroll, etc). I have a iMac user Yosemite. Thanks for the support.
<Re-Titled By Host>Hi PietralataKK,
I understand your mouse was working fine but now you have lost the multitouch features of the mouse. You don't mention if you can click or move the cursor with it.
For this please start with this article to troubleshoot,
Desktop computers: Troubleshooting wireless keyboard and mouse issues in Mac OS X v10.5 - Apple Support
Then for the "trackpad" functionality check out,
Trackpad or Magic Trackpad is jumpy or erratic - Apple Support
Yes, it talks about Magic Trackpad, but the top of the Magic Mouse is like that.
Thank you for visiting Apple Support Communities.
Nubz -
I have just purchased Real player 15sp but it does not seem to recognise Firefox13? and I cannot use the extra functions that it has. Example I cannot download videos. Thank you.
JackCannot download videos
This is caused by the RealPlayer Browser Record Plugin extension. To fix it, disable the extension.
The RealPlayer plugin will still work.
At the top of the Firefox window, click on the Firefox button (Tools menu in Windows XP), and then click Add-ons. The Add-ons Manager tab will open.
In the Add-ons Manager tab, select the Extensions panel.
Select RealPlayer Browser Record Plugin.
Click on Disable.
Click Restart Now to start Firefox with the extension disabled. My add-on manager says the add-on is disabled.
I tried this and it didn't work, what else? -
I lost my iphone and I use the locate iphone function to wipe to protect my information, but I cannot get the location to restore my iphone, can I request a permanent lock to prevent the thief from using it?, I call your call centre, your staff said they can do nothing, I am great disappointed as your advertisment said that we can protect our phone from lost, however, I think my phone has now been resale and reuse by others, but Apple cannot do anything with your so call "Find my iphone" function, I have brought 4 iphone and iPad for my family use, I will never use your product again and recommend to my company or friends anymore!
Philip SinYou are not addressing Apple here at all.
Apple can do nothing. Sorry.
Like any other make of any other phone, they cannot permanently disable it.
The thief is responsible. Not Apple. You seem to be directing your anger at the wrong people.
No phone manufacturer will do this.
"I am great disappointed as your advertisment said that we can protect our phone from lost, "
It mentions "loss" NOT theft. you cannot find a mention of theft protection. Find my iphone is NOT theft protection and has never been advertised as such. -
Using the Safe Mode function on your PlayStation 3?
i followed the steps it works fine then when i sign in within a afew seconds it cuts off and gets a red flashing light again i dont know what to do :/
RabidWalker wrote:
Using the Safe Mode function on your PlayStation 3?
Safe Mode:
The option to use Safe Mode on the PlayStation 3 was introduced if a problem occurs where it will no longer start up normally.
To use this feature the console will need to have the System Software update 2.60 (or later).
When to Use Safe Mode?
When starting up the PlayStation 3, and the XMB menu no longer appears (you may see a wavy line on the background instead).
When the PlayStation 3 is started up, nothing appears on screen.
When the PlayStation 3 is started up and you encounter the following message ‘The Hard disk’s file system is corrupted and will be restored’. When selecting ‘OK’ the system restores and restarts, however the same message appears.
When the PlayStation 3 is started up and you encounter the following message ‘The Hard disk’s database will be rebuilt’. When selecting ‘OK’ the system begins the operation and then fails (stopping the restoration of the HDD).
There is an issue after the PlayStation 3 update process is started, or a rebuilding of the database occurs.
Safe Mode procedure:
1) Ensure the PlayStation 3 is in standby mode (where the red light is apparent), and then turn the console off at the mains switch.
2) Turn the mains power on, then while in standby touch and hold the power button.
3) Keep your finger pressed on the power button (after 5 seconds you will hear a beep).
4) After 10 seconds of holding your finger on the power button, you will hear a second beep and the console will shut down (you can remove your finger).
5) Touch and hold the power button again.
6) Again hold your finger down on the button until you hear another beep after 5 seconds.
7) A number of seconds after this you will hear a double beep- you can remove your finger.
8) You will be prompted to plug your controller in and press the PS button on your controller. After doing so you will access the Safe Mode menu with a number of options.
Safe Mode Option Screen:
Restart System
Selecting this option will start up the system normally- It will also allow you to exit the Safe Mode Menu.
Restore Default Settings
Selecting this option will restore Default settings on your console (when starting the unit you will be prompted to set time, time zone etc). This option will also delete your PlayStation Network account information from the system.
Your User information will be deleted and restored- the indicator will be an asterix by your username e.g. *RabidWalker.
When logging into your user you will encounter no issues with disc based games. However when attempting to play PSN downloaded games you may encounter the message:
‘To access the system, you must activate the system.
Go to [PlayStation Network] > [Account Management] to activate this system. (80029514). ’
Follow the instruction to activate your PlayStation 3 to play downloaded games (if the system is activated, deactivate and reactivate the system)
Restore File System
This option will begin a process to repair data on your Hard Disk Drive. Therefore it will check for any corrupted data and try and recover this. It the data cannot be recovered it may be erased to ensure that it does not interfere with the operation of the PlayStation 3.
Rebuild Database
If issues continue to persist and you select this option please note that data will be removed during this process.
The following information will removed:
- Messages
- Playlists
- User changes to Information Screens
- User changes to Picture under Photos
- Video Thumbnails
- Video Playback History
- Video Resume Information
This process may take same time to complete
Restore PS3 System
The option to restore PS3 system is the same as the ‘quick format’ option on the XMB menu. It will reformat the HDD, removing all data and restoring the Hard drive to its original state.
System Update
Selecting this option will install the PlayStation 3 Update but only if the update is on an external media storage device plugged into the console.
This option can be used if any issues are encountered with the installation of the System software update.
If you have any queries regarding this or any other issues please PM me or catch me on Twitter
@RabidWalker
Rabid
-
You cannot maintain the address (partner function 'Ship-to party' is empty)
Dear Experts,
I create one outbound delivery but when I click on address ( Symbol next to ship to party) it is showing below error.
You cannot maintain the address (partner function 'Ship-to party' is empty)
Message no. VPD017
I also check customer master , address is maintain properly.
in partner functions Sold-to party , Bill-to party , Payer , Ship-to party all are same. ( example: if bill to party is ABC then payer , ship to pary , bill to party all are ABC).
Please help.
Regards,
Nirav DesaiHii Nirav Desai,
You do correctly "configure automatic partner determination". The steps are as below -
Customer Master
Sales Document Header
Sales Document Item
Delivery Type
Shipment Type
Billing Header
Billing item
Sales Activities
1. How to define partner?
A grouping of partner functions. The procedure specifies which partner functions are allowed for a particular business transaction (for example, for processing a sales order) and which of those partner functions are mandatory.
Use
You define partner determination procedures in SD Customizing through Functions -> Partner determinat.
u2022 In sales documents, for example, you can specify the partner determination procedure according to sales document type and item category. During order entry, the system first proposes partners from the customer master record of the sold-to party. If this information does not exist in the customer master, the system automatically proposes the mandatory partners from the partner determination procedure that you specify in the document header.
u2022 For billing documents, for example, you can specify a partner determination procedure where the sold-to party, bill-to party, and payer are mandatory but the ship-to party is not (for billing, you are more interested in who orders and pays for the goods than in who receives them).
Thanks and Regards,
Santanu -
"Cannot use the connection type ...."
Nokia 6233
Windows XP SP2
LaunchApplication.exe v 6.82.70.1
Bluetooth "i.Tech BlueCON U"
O2 Bluetooth Dongle Drivers
Using Bluetooth OK to download photos to PC, but no other function so far.
Trying Nokia PC Suite to perform various functions - failure in all cases, common message is "Cannot use the connection type. Check that the needed hardware, software and drivers are available".
No clues anywhere as to what is needed.
Bluetooth clearly works. Nokia PC Suite can't use it.
Totally stuck - wish to use PC connection to synchronise address books.
Help, please.Hi,
I think that PC Suite is not support your Bluetooth driver. Here you can find what drivers are supported:
/discussions/board/message?board.id=connectivity&message.id=114
Anyway, if Microsoft's BT driver support your BT HW, you can try to that stack also...
So, if you want to try to use MS BT driver:
1. Go to Control Panel, System, Hardware and Device Manager.
2. Open Bluetooth Devices, select that device, click Action, Uninstall and OK.
3. Click Action and Scan for hardware changes.
(windows should automatic install MS BT driver) -
Lock the plant so that other user cannot use the same plant.
Hi Gurus!
I ahve this small report which shows the pro-rate factor . In this report I need to block the plant or lock it(a soft) lock witha message that some other user is using the plant so that other cannot use the same plant to post.Following is the report and if soemone can help me out would be very kind enough.I ahve added teh code where validation of plant is doen , so it must be somewhere here the locking should be done as per my thinking . Kindly suggest please.
*& Form get_pro_factor
* get pro rate factor from the given
* combination of plant/sloc/mat#/period
form get_pro_factor .
select single zpr_factor zpr_disp_factor zpr_pipe_net zpr_pipe_gross
from zprfactor
into (zprfactor-zpr_factor, zprfactor-zpr_disp_factor,
zprfactor-zpr_pipe_net, zprfactor-zpr_pipe_gross)
where zpr_werks = p_werks and
zpr_lgort = p_lgort and
zpr_matnr = p_matnr and
zpr_mjahr = p_mjahr and
zpr_monat = p_monat.
v_subrc = sy-subrc.
if zprfactor-zpr_factor = 0.
if c_wp = p_lgort+0(2).
zprfactor-zpr_factor = 1. " Don C added this routine
endif.
endif.
if zprfactor-zpr_disp_factor is initial.
if not zprfactor-zpr_pipe_gross is initial.
zprfactor-zpr_disp_factor = zprfactor-zpr_pipe_net / zprfactor-zpr_pipe_gross.
endif.
if zprfactor-zpr_disp_factor is initial.
zprfactor-zpr_disp_factor = 1.
endif.
endif.
endform. " get_pro_factor
*& Form valid_plant
* validate whether plant entered in selection screen
* exists in database or not
form valid_plant .
if not ( p_werks is initial and
p_lgort is initial and
p_matnr is initial and
p_mjahr is initial and
p_monat is initial ).
select single werks from t001w into t001w-werks
where werks = p_werks.
if sy-subrc ne 0.
message e048(zmm) with p_werks.
endif.
endif.
endform. " valid_plant
*& Form FIND_MATKL
form find_matkl .
select single matkl into v_matkl from mara where matnr = p_matnr.
endform. " FIND_MATKL
*& Form UPDATE_ZPRFACTOR
form update_zprfactor using p_flag. "DEVK903224
call function 'ENQUEUE_E_TABLEE'
exporting
mode_rstable = c_e
tabname = 'ZPRFACTOR'
exceptions
foreign_lock = 1
system_failure = 2
others = 3.
if sy-subrc <> 0.
message id sy-msgid type sy-msgty number sy-msgno
with sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
else.
select single * from zprfactor where zpr_werks = p_werks
and zpr_lgort = p_lgort
and zpr_matnr = p_matnr
and zpr_monat = p_monat
and zpr_mjahr = p_mjahr.
if sy-subrc = 0.
zprfactor-zpr_rate_flag = p_flag. "DEVK903224
update zprfactor.
endif.
endif.
call function 'DEQUEUE_E_TABLEE'
exporting
mode_rstable = c_e
tabname = 'ZPRFACTOR'.
Thanks
Aaravcall function 'ENQUEUE_E_TABLEE'
exporting
mode_rstable = c_e
tabname = 'ZPRFACTOR'
exceptions
foreign_lock = 1
system_failure = 2
others = 3.
ENQUEUE_E_TABLEE } E_TABLEE is the name of the lock object, it starts with character "E". -
Using the Array SetElements function
Hi All,
I'm trying to use the Array SetElements function to set a value to specific indices within an initialized array but I cannot figure out what the syntax is for the optional parameter 2. I've tried a whole bunch that seem to make sense but always get an error. Has anyone used this function before who can let me know what the syntax to use is?
Thanks,
Nick
Solved!
Go to Solution.Nick,
So the syntax for setting all of the elements to a value can simply be written:
SetElements( myArray,valueToSet )
To add in the optional parameter 2 and define a range is something like this:
SetElements( myArray,valueToSet, "[3..6]" )
The .. operator is analagous to a : in Matlab.
Good luck,
Chris -
Equium A200-15i: I cannot use the touch pad - no response
I cannot use the touch pad in my equium A200-15i.
When I touch the pad, there is no response at all.
Please help me to solve it.
I have tried to uninstalled the program and reinstalled it, but problem still exists.Hi
Did you check if the touchpad is enabled correctly???
Using the key combination FN+F9 you can disable and enable the touchpad functionality!
Please check this function if you have not disabled the touchpad accidentally!
Last but not least I would recommend checking the touchpad settings in the control panel mouse -> Advanced -> Advanced feature settings.
There you will find different options which can be configured to use all the available touchpad features.
Best regards -
Since installing LTR 5.4, which I've now upgraded to 5.6, I've encountered repeated slowness and malfunctions in operations, especially when using the Compare View function and the Tab key to open and close the right and left side panels. Such problems never arose during two years of using LTR-4 and nothing else has changed on my computer. I have a pretty simple system with only a few plug-ins, which are usually not in operation. I have 12GB of RAM in my Windows 7 PC. I could illustrate these problems with screen shots if you would tell me how to submit screen shots. Otherwise I will try to describe the problems in words.
The problem is clearly cumulative, growing worse as usage time passes. Compare View feature gradually slows down and eventually seems to choke as my work session proceeds. If I Exit LTR and re-enter and start all over, things will work normally for maybe 30 minutes, but then the Compare View feature begins to become very slow to respond. In a recent example with my screen full of thumbnails in Library mode I highlighted two images to compare. LTR started to open the Compare View screen by first having the top row of thumbnails disappear to be replaced by the "SELECT" and "CANDIDATE" words in their spaces (but no images), but Compare View never succeeded in gaining control of the screen. After some seconds the top row of thumbnails reasserted its position and the Compare View windows disappeared. But LTR kept trying to bring them back. Again the top row of thumbnails would go away, Select and candidate would reappear, try again, and give up. This went on for at least 2-3 minutes before I tried to choose File and Exit, but even that did not initially want to respond. It doesn't like to accept other commands when it's trying to open Compare View. Finally it allowed me to exit.
To experiment I created a new catalog of 1100 images. After 30-40 minutes, the Compare View function began to operate very slowly. With left and right side panels visible and two thumbnails highlighted, hitting Compare View can take half a minute before the two mid-size images open in their respective SELECT and CANDIDATE windows. When the side panels are open and two images are in the Select/Candidate spaces, hitting the Tab button to close the side panels produces a very delayed response--25-30 seconds to close them, a few more seconds to enlarge the two images to full size. To reverse the process (i.e., to recall the two side panels), hitting Tab would make the two sides of the screen go black for up to a minute, with no words visible. Eventually the info fields in the panels would open up.
I also created a new user account and imported a folder of 160 images. After half an hour Compare View began mis-placing data. (I have a screen shot to show this.) CANDIDATE appears on the left side of SELECT, whereas it should be on the right. The accompanying camera exposure data appears almost entirely to the left of the mid-screen dividing line. Although the Candidate and Select headings were transposed, the image exposure data was not, but the data for the image on the right was almost entirely to the left of the line dividing the screen in two.
Gurus in The Lightroom Forum have examined Task Manager data showing Processes running and Performance indicators and they see nothing wrong. I could also send screen shots of this data.
At this point, the only way I can process my images is to work 30-40 minutes and then shut down everything, exit, and re-start LTR. This is not normal. I hope you can find the cause, and then the solution. If you would like to see my screen shots, tell me how to submit them.
Ollie
[email protected]Since installing LTR 5.4, which I've now upgraded to 5.6, I've encountered repeated slowness and malfunctions in operations, especially when using the Compare View function and the Tab key to open and close the right and left side panels. Such problems never arose during two years of using LTR-4 and nothing else has changed on my computer. I have a pretty simple system with only a few plug-ins, which are usually not in operation. I have 12GB of RAM in my Windows 7 PC. I could illustrate these problems with screen shots if you would tell me how to submit screen shots. Otherwise I will try to describe the problems in words.
The problem is clearly cumulative, growing worse as usage time passes. Compare View feature gradually slows down and eventually seems to choke as my work session proceeds. If I Exit LTR and re-enter and start all over, things will work normally for maybe 30 minutes, but then the Compare View feature begins to become very slow to respond. In a recent example with my screen full of thumbnails in Library mode I highlighted two images to compare. LTR started to open the Compare View screen by first having the top row of thumbnails disappear to be replaced by the "SELECT" and "CANDIDATE" words in their spaces (but no images), but Compare View never succeeded in gaining control of the screen. After some seconds the top row of thumbnails reasserted its position and the Compare View windows disappeared. But LTR kept trying to bring them back. Again the top row of thumbnails would go away, Select and candidate would reappear, try again, and give up. This went on for at least 2-3 minutes before I tried to choose File and Exit, but even that did not initially want to respond. It doesn't like to accept other commands when it's trying to open Compare View. Finally it allowed me to exit.
To experiment I created a new catalog of 1100 images. After 30-40 minutes, the Compare View function began to operate very slowly. With left and right side panels visible and two thumbnails highlighted, hitting Compare View can take half a minute before the two mid-size images open in their respective SELECT and CANDIDATE windows. When the side panels are open and two images are in the Select/Candidate spaces, hitting the Tab button to close the side panels produces a very delayed response--25-30 seconds to close them, a few more seconds to enlarge the two images to full size. To reverse the process (i.e., to recall the two side panels), hitting Tab would make the two sides of the screen go black for up to a minute, with no words visible. Eventually the info fields in the panels would open up.
I also created a new user account and imported a folder of 160 images. After half an hour Compare View began mis-placing data. (I have a screen shot to show this.) CANDIDATE appears on the left side of SELECT, whereas it should be on the right. The accompanying camera exposure data appears almost entirely to the left of the mid-screen dividing line. Although the Candidate and Select headings were transposed, the image exposure data was not, but the data for the image on the right was almost entirely to the left of the line dividing the screen in two.
Gurus in The Lightroom Forum have examined Task Manager data showing Processes running and Performance indicators and they see nothing wrong. I could also send screen shots of this data.
At this point, the only way I can process my images is to work 30-40 minutes and then shut down everything, exit, and re-start LTR. This is not normal. I hope you can find the cause, and then the solution. If you would like to see my screen shots, tell me how to submit them.
Ollie
[email protected] -
How do I use the Match Pattern Function to exclude only 0.000?
Hi,
I'm trying to use the mattch pattern function to find the first string in a table thats is >0. My table looks like:
1,0.000000,0.000 %2007/01/13 00:16:19 196281
1,0.000000,0.000 %2007/01/13 00:16:22 196282
1,0.831262,0.000 %2007/01/13 00:17:20 196375
2,0.811154,0.000 %2007/01/13 00:17:20 196375
If I us the paremeter "1,[~0]" It doesn't find the line 1,0.831262,0.000... which is the one that I want. I also tried :1,[0-9].+[~0] and that didn't work either. the problem is that the first digit after to 1, isn't allways going to go from 0 to 0.0 sometimes it might go from 0 to 2.??.
Thanks for the help
Matt"Matt361" <[email protected]> wrote in message news:[email protected]..
Hi,
I'm trying to use the mattch pattern function to find the first string in a table thats is >0. My table looks like:
1,0.000000,0.000 %2007/01/13 00:16:19 196281
1,0.000000,0.000 %2007/01/13 00:16:22 196282
1,0.831262,0.000 %2007/01/13 00:17:20 196375
2,0.811154,0.000 %2007/01/13 00:17:20 196375
If I us the paremeter "1,[~0]" It doesn't find the line 1,0.831262,0.000... which is the one that I want. I also tried :1,[0-9].+[~0] and that didn't work either. the problem is that the first digit after to 1, isn't allways going to go from 0 to 0.0 sometimes it might go from 0 to 2.??.
Thanks for the help
Matt
Hi,
1,[~0] matches a "1" a "," and then any character that is not "0".
1,[0-9].+[~0] matches a "1" a "," and then any character that is "0-9", any number of anything!! (1 or more) and then anything that is not "0". Note that you have to escape a . to match a ".". Like this "\.".
There is no way to check if there is anything other then a "0" in the match, from within the match pattern function. So I think you won't be able to find a pattern that does the trick.
Why not use a whileloop to find the first item? Or use the Spreadsheet String To Array, and then compare the desired row or column with the string "0.000000"? (Or replace all ,0.000000, by a string like ",NULL,", then match the pattern?)
In LabVIEW 8 there is a new Match Regular Expression function. Haven't tried it, but it should be much more powerfull then the Match Pattern function. But also much more complex.
Regards,
Wiebe.
Maybe you are looking for
-
Trouble sending files via bluetooth from my powerbook to Blackberry Pearl
I didn't know who else to check first. So I'm taking a chance here. Over the weekend I made the big step of purchasing a Blackberry Pearl 8100. I was looking forward to trying the bluetooth feature. So I paired my phone with my Powerbook G4. Everythi
-
Cannot open a pdf file - i get a long string of coding and no text
I try to open a pdf file but get a string of codes.
-
How to send reply to the sender of a multicast messg
Hii all, I have a problem in sending reply to the sender of a multicast message. My problem is that, a process sends a request to all the peer processes in a multicast group and the receivers have to send a reply to this request and the reply should
-
Problems with messaging locking up
I have had my Charge for about a year now and I don't have many complainants about it, but recently when using the text messaging it started locking up if there was a MMS that was included in the stream. The only way I have found to fix it is to dele
-
i used to download app using my freind ID nw i get mine so i try to sync wiz itunes in lap it ask me to authorize and it already authorized but keep asking to authorize ???? what shall i do ?