Canon 7D tethered stopped working

When I click the shutter either on the camera or using LR, the message 'Transferring Files from Camera' stays and nothing happens.
I'm pretty sure this stopped working after upgrading to LR3.5
I upgraded to LR3.6
Tried three different USB cables
Tried each USB port with each USB cable combination
Rebooted
Followed every step here:
http://kb2.adobe.com/cps/894/cpsid_89486.html
Note, everything works fine using Canon EOS Utility
I noticed someone mention upgrading to LR3.6C but I don't see where to download that. Wouldn't it be here?:
http://www.adobe.com/support/downloads/product.jsp?product=113&platform=Windows
Also, in this article:
http://kb2.adobe.com/cps/842/cpsid_84221.html
5D, 1Ds Mark II, 20D, EOS 350D (Rebel XT/EOS Kiss Digital N) on Windows require a driver downloaded from Canon. This driver is not available for 64-bit versions of Windows.
Is it possible that the 7D should be included in that list?
My setup:
Sony VAIO laptop
Window 7 x64 SP1
Intel i5 2.67GHz
4GB RAM
USB 2.0
LR3.6
Is anyone else successfully shooting tethered with a Canon 7D?

I'm happy to say that tethering is working after installing LR4.
Thanks!

Similar Messages

  • Canon MP Navigator stopped working.

    Canon MP Navigator stopped working.  twain_32 folder contains only wiatwain.ds and CNQ4507.  No PIXMA MX870 were present.  Please advise.

    Hi bcb,
    Please try downloading the updated MP Navigator from the following website: 
    http://usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mx_series/pixma_mx870#Driver...
    If the error remains afterward, or there is any difficulty with the procedure, please visit the link below for further assistance.  Thanks so much! 
    http://www.usa.canon.com/cusa/consumer/standard_display/contact_us_consumer
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • IPhone 3G Tethering stop working after upgrade to OS4

    Hi, I have upgraded my iPhone 3G to OS4 and Tethering stop working. I am using iTunes 9.2 for both Mac OS Snow Leopard and Win XP. It indicate that USB is not connected for both OS. Any help will be appreciated.

    I had the same problem after attempting to update last night (on my 3G). The loss of wifi was the least of my worries, however. The update process wiped out my entire phone and reset it as a new phone, and never performed the back up. So, I wasn't able to restore from a back up. It's a glitch in the update, nothing that I did, or didn't do. The issues are too long to list... UGH!
    After hours on the phone with AppleCare Sr Support last night, and 5 hrs at Apple Store today (no exaggeration!), they replaced my phone entirely. Luckily, I had a MobileMe account so, I was able to retrieve/restore my contacts and apps (although the data within my apps was lost - so I have to go through all of them again). Also lost all iCal data... two years worth... not sure how that happened, since that was also synced via MobileMe... the whole update is a mess... If you haven't updated yet, I would wait to update until they work out any kinks.

  • Canon MP Navigator Stopped Working (MX870)

    Running Windows7, 64 bit Oper System
    Canon MX870
    Scanning was not an issue prior to a few days ago. No new software or programs have been installed.
    Went to scan a document and scanning looked like it was working, then it greyed out and received error message: Canon MP Navigator EX has stopped working.
    Searched internet for solutions and tried them. Nothing works. I've gone as far to un-install all Canon products and utilities, even went into registry and searched and removed everything I thought I could related to Canon.
    Still receive error. What do I do now?
    Guess I've pretty much stumped the panal since there's been no response
    Solved!
    Go to Solution.

    Hi jealkon,
    There may be a third party scanner driver interfering with MP navigator.  Please try the following:
    1.  Click 'Start' and then 'Computer'.
    2.  On the left-hand pane, click the down arrow beside Local Disk (C: ).
    3.  Click the down arrow beside Windows to open the folder
    4.  Highlight the twain_32 folder.
    5.  The folder should have 2 folders that start with PIXMA MX870 and a file called wiatwain.ds.  Any other folders or files should be dragged to the desktop. 
    6.  Reboot the computer and try scanning again.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • Tethering Stopped Working??

    With 3.1 tethering my XTi (400D) was working and I was soo excited because this is one of the features I have wanted for a while when I am doing studio shooting. But for some reason it has stopped working and I have no idea why?
    It sees my camera when I plug it in for import, but when I go to the tethering ( File > Tether > Start Session ) nothing happens. No error, no connection, just nothing.
    Any ideas on how to troubleshoot this?

    Spikeyjonze,
    Thank you very much for sticking with me on this one, I figured it out tonight. It is 90% operator error and 10% a misleading application error. You have to be in a "Project" for tethering to work, even though while you are in an "Album" the "Start Session" is active it doesn't actually do anything. Now I thought I was shooting into a Album before, but I must have just been mistaken.
    So, Aperture developer types. I think an "Album" should act the same as a "Folder" and when you select tethering none of the options are available to choose. Here is a screen shot of tethering when I have an Album selected.
    http://www.vensland.com/wp-content/gallery/blog-photographs/screen-shot-2010-11- 02-at-8-29-51-pm.png

  • Bluetooth tethering stopped working

    Hi,
    I’ve been using my phone’s data connection to go online with my macbook by way of Bluetooth. It’s been working fine for about a year, but sometime in the past few months (possibly after the 10.5.6 update) it stopped working. Now when I try to hit the connect button in the network preference panel, I get "A Bluetooth serial failure has occurred: Failed to open an RFCOMM serial channel. Check if authentication needs to be enabled in your device."
    I’m sure that nothing has changed on the phone, so somehow the OS isn’t recognizing the phone as a modem anymore. Can anyone offer up any help?
    Thanks

    deleting the blues tooth preferences would reset them to default.
    but to revert to an earlier of bluetooth you may want to try replacing 2 bluetooth drivers from your install DVD.
    Use pacifist so extract and install
    /System/Library/Extensions/IOBluetoothFamily.kext
    /System/Library/Extensions/IOBluetoothHIDDriver.kext
    disclaimer I have not needed to do this on my system and cannot be responsible if anything breaks it is just a suggestion.

  • Canon MX870 scanner stopped working

    The fax still works but scanner gives a "stopped working" error.  I have tried all the usual trouble shooting including going to the twain32 folder to check for third party interference.  Nothing has worked.  Any ideas?

    Hi katevancolen!
    So that the Community can help you better, we will need to know the Computer Operating System you're using (Windows XP/Vista/7/8 or Mac 10.x), and how you're connecting to your device (USB, Wi-Fi, or ethernet). Any other details you'd like to give will only help the Community better understand your issue! Thanks and have a great day!

  • Help with Canon MX870 - scanner stopped working

    Hi,
    I bought a Canon Pixma MX870 printer/scanner a month or so ago and it was working fine up till this week. I had installed the Canon software and ran the OS X Software updpate when setting it up.
    All of a sudden last week I couldn't print. It kept saying the printer couldn't be found. So I downloaded the Apple Canon printer software and reinstalled it thinking it couldn't do any harm. The printer is working again. The scanner not so much. If I do manage to get it to work (either by using the scanner from System preference > Print/Fax > and choosing open scanner or by using the MP Navigator it typically now will only work 1 time. After that it says "scanner not found" and sometimes if I close and reopen the scanner from Print/Fax it says "trying to open scanner session".
    I know the MX870 is connected to the network. The blue wifi light is lit, it shows in the router's list of connected devicies, it also shows in Safari's list of Bonjour Devices.
    I need this machine to scan and play nice with OS X - I need to scan more than print.
    I ran Disk Warrior, ran chrons to do maintenance and fix permissions etc. I tried deleting and re- adding the scanner. That didn't work and I had to restore it from backup.
    Anyone have any ideas on what to do next?
    Thank you.

    Marlinespike wrote:
    However, I went to take a screenshot and something very weird happened. It popped up a dialog box where the scanner was checked as shown in your screenshot with an 80.????? IP address (the ? are because I don't recall)
    The 80 number would have been the MX870 wifi network address - not the IP address. The scanner selector tool does not show the device IP address, only the network address.
    ...asking if "Canon IJ Network Scanner Selector 2" could accept incoming connections from the network and there was a 3rd choice listing the scanner as "Canon MX870 series_3DXXXXX (where I am putting in Xs because I suspect it is a serial number).
    Based on this I would guess that the firewall is enabled on your Mac and the prompt is to add an exception to for the networked MX870 (and the X's are the last digits of the wifi network address shown in the selector tool) so that communication can flow between both devices.

  • Tethering stopped working on windows 7 after itunes 10.7 update

    This problem seems to have been addressed many times in the forums for Apple OS, but not for Windows. Most reponses refer to the kext files which as I understand do not apply to Windows?
    I have an iphone 3G that I updated to IOS 6.0.1, and this also required me to update iTunes to 10.7. However after the update USB tethering no longer works, nor can I get USB hotspot to work. The driver installation repeatedly fails.

    Sorry I didn't update this sooner. Not sure exactly what worked, but what I did was uninstall some recent Windows Updates, uninstall the MotionInJoy drivers I was using to get a PS3 controller to work (I had read these drivers could be an issue), restarted at least once or twice, and FINALLY got Bluetooth working again. Then (re)updated Windows, but NOT the Bluetooth update that was available (perhaps I did the first time around, and perhaps it isn't Boot Camp friendly), and then reinstalled MotionInJoy, but kept the PS3 controller plugged in via USB, as when it goes Bluetooth, apparently it overwrites all other Bluetooth drivers, which could have been my original problem.
    Anyway, all of the above has been working just fine for a couple of weeks now, but I continue to avoid installing the available Bluetooth update via Windows Updates, just in case.

  • Canon 70D suddenly stopped working

    I recently shot a job with my 70D, came home and uploaded my photos with a card reader. Today, I reinserted my card and camera would not turn on. I put batteries, including my fully-charged backup battery, in charger. I inserted the two were fully charged batteries and it's still not working. I found out my 3rd-party batteries have not communicating with my camers. Only when I inserted my Canon battery in the single-battery postion, does it work. I just ordered two more Canon batteries 

    Hi zimbobway! Thanks for posting. Am I to understand correctly that you are using a battery grip with the camera and it will only power on with a single battery in the battery compartment of the camera without the battery grip installed? If so, are you also using a third-party grip or are you using a Canon grip?   Does the grip power the camera on when only Canon batteries are used in it?

  • USB Tethering stopped working after OSX Update to 10.6.4

    I'm using the I-Phones tethering option on the swiss Swisscom network on daily bases.
    So far no problem using it with the USB cable.
    Since the latest OSX Update the availability of tethering by USB is very inconsistent.
    Bluetooth works perfectly.
    Strangely the Network panel shows the USB connection as not functioning but all I-Phone Functions such as I-Tunes connection, picture connection to I-Photo works perfectly.
    Deleting and reactivating the USB-I-Phone setting in the network panel didn't work neither resetting the network services on the I-Phone
    Any ideas how to get this back to work?

    WillRukMac wrote:
    I have the same problem as you... If you solved it can let me know too? Hope someone reply this thread help us!
    I've found a post in google - Reregister your I-Phone in I-Tunes.
    It worked for me so far.

  • Since upgrading to OS X Yosemite my Canon LBP6000 has stopped working ???

    - I have worked through all the Printer Troubleshooting suggestions from Apple Help ..... I have checked all the cords are plugged in, my MacBook Pro has been restarted twice, I have deleted the Printer and Added it again ..... ???
    So annoying.....

    G'day Pahu .... thanks for having a go at helping me out ... much appreciated....
    Now, I'm not sure if this is what you are after ????
    Canon LBP6000/LBP6018:
      Status:    Processing
      Print Server:    Local
      Driver Version:    3.55
      Default:    Yes
      System Printer Sharing:    Yes
      Shared:    No
      URI:    usb://Canon/LBP6000/LBP6018?serial=0000B1C43Ejl
      PPD:    Canon LBP6000/LBP6018 CAPT (UK)
      PPD File Version:    3.55
      PostScript Version:    (3010.000) 550
    (3010.000) 651
      CUPS Version:    2.0.0 (cups-408)
      Scanning support:    No
      Printer Commands:    none
      CUPS filters:
    capdftopdl:
      Path:    /Library/Printers/Canon/CUPSCAPT/Bins/capdftopdl
      Permissions:    rwxr-xr-x
      Fax support:    No
      Printer utility:    /Library/Printers/Canon/CUPSCAPT/StatusMonitor/StatusMonitor.app
      Printer utility version:    3.55
      PDEs:
    FinishingPDE.plugin:
      Sandbox compliant:    Yes

  • USB tethering stopped working after iMac software update.

    Yesterday my Internet was slooooow so I followed a tip to repair disc permissions in disc utility, at the same time I was downloading and installing software update for the iMac. I've always tethered with a USB cord (Bluetooth has NEVER worked with the Mac and phone, but does with the iPad).  All the solutions I find one here for this issue give instructions I don't understand (where/how to do them exactly, like iPhone config utility...where?!), and how I'm supposed to download iTunes again on a mac that has no Internet because i can't tether...physically impossible. Very frustrated.  I don't understand why software updates are issued that cause problems like this, but no immediate solutions updates are issued after. One top of that, how are we supposed to fix issues when we can't tether and dont have separate Internet (I can't update my iPhone software without a special trip to a wifi hotspot....I live in Saudi Arabia...it's not easy to do that).
    Sorry, so many questions. Frustrated.  I there a SIMPLE solution out there?!

    WillRukMac wrote:
    I have the same problem as you... If you solved it can let me know too? Hope someone reply this thread help us!
    I've found a post in google - Reregister your I-Phone in I-Tunes.
    It worked for me so far.

  • Since upgrading to OS X Yosemite my Canon LBP3300 has stopped working ???

    Please help me !!!

    First step is to remove the LBP3300 from Printers & Scanners.
    Next, open Finder and select Go > Go to Folder. Then type (or copy) the following and press the Go button.
    /Library/Printer/Canon
    Here you will see the CUPSCAPT folder. Trash this folder.
    Still in Finder, use the Go > Go to Folder and type (or copy) the following and press the Go button.
    /Library/LaunchAgents
    Trash the file "jp.co.canon.CUPSCAPT.BG.plist"
    Last action in Finder is to use the Go > Go to Folder and type (or copy) the following and press the Go button.
    /Library/Caches
    Here you will see the Canon folder which you can Trash.
    With the above complete, empty the Trash and restart the Mac. Once you have logged back in download and install the CAPT v3.67 driver. When the installation has completed, open Printers & Scanners and add the LBP3300. Then see if you can print.

  • Help! canon 9000f scanner stopped working

    - says error connecting the scanner. USB cable is connected and drivers reinstalled (twice) but same message. Interestingly it recognizes the scanner hardware but when i press the scan button it gives error 2.155.33

    Hi nikinhkg,
    Thanks for visiting Apple Support Communities.
    You may find the troubleshooting steps in this article helpful:
    USB and FireWire Quick Assist
    http://support.apple.com/kb/ht1151
    You may also want to try the steps in this article:
    Troubleshooting printer issues in OS X
    http://support.apple.com/kb/TS3147
    Best,
    Jeremy

Maybe you are looking for