Canon iRC4580, One Job to different Papertrays

We use the large Office Printer iRC4580 from Canon. We installed the latest driver 2.0.6
With all printer we know with Apple OS X we have to option to Print the First Page to Tray X and all the others to Tray Y.
With the Canon we have only the option to print to ONE tray and not the split to different trays. Is their a workaround to solve this problem?
Gérard

In the meantime I found a partly solution.
The UFR driver isn't correct (or not for our purpose). I have found the PPD 3.10 driver. With this it is possible, but I need a german driver, this is only availible in the Version 2.90
Is their a way to copy the resources from the german version 2.9 to the us version 3.1?
Here are the original files
3.10 US /Englisch
http://www.canon.ca/inetCA/userfiles/isgdriver/PS0310_osxtlsl_na_Installere.zip
2.9 Deutsch
http://software.canon-europe.com/software/0038591.asp
Gérard

Similar Messages

Airport Printing fails after one job

There seems to be a lot of printing issues with Airport but I can't find a solution for my problem.
I have an Airport Extreme attached to a USB printer.
It will print fine from my Powerbooks running Tiger or Leopard but when I try to print from the new iMac running Snow Leopard it will only print one job and then fail to continue unless I reset the Airport.
All printers work fine via USB.
Any help appreciated

I've got an Airport Extreme Base station.
I've plugged in an USB concentrator on which I have
connected my usb Canon S750 printer and an USB2
HardDrive.
As I don't need this drive all the time, I only power
it when needed.
Everything goes well until I disconnect this Hard
drive.
Eventhough I properly eject it from my iMac desktop
first, whenever I power it off and/or unplug it from
the usb concentrator, the connection to the Airport
Shared printer is lost....
I can't print anymore on it unless I power off then
on the Airport Base Station (or Reset it from Airport
utility).
Has anyone been confronted to this same behavior?
Anyway to solve it?
What USB Hub are you using? Is it a powered Hub?

SAP Scheduler. Multiple jobs for one job definition issue.

Hi.
I am facing one problem concerning scheduling jobs. I've created a job definition and deployed it on server. In onJob(...) method system queries to DB for a single result, when this result matches some conditions job is finished, otherwise it waits for a minute and then queries again. Then I tried to create several tasks for this job definition and set similar execution time for all tasks to check their simultaneous behavior. I was surprised to find out that only one job status is 'RUNNING' and for others status is 'STARTING'. But I expected to see all my jobs in status 'RUNNING'. At first I thought the problem was in MDB pool stuff(e.g. InitialSize of beans or something like that), supposing that there is only one working bean and huge queue of messages. But nothing changed after setting different values for pool params.
So, can anyone help me to make at least 2 simultaneous working jobs for one job definition, if it possible, off cause. Or may be I am wrong somewhere. (By the way, I used Threads in MDB for waiting).
Thanks in advance.

May be I described my problem rather messy. The main question is it possible to create several jobs for one job definition and see them running at the same time (simultaneously)?
Thanks.

Multiple IT1005 for one job

Can we have multiple planned compensation (IT1005) records for one job within the same country? The standard SAP has the time constraint as "3" for IT1005 and that means that it can have multiple records with the same dates. We want to use different pay structures for various positions attached to the same job. How is it going to affect the sub-modules in ECM like Job Pricing where the Job Evaluation/Survey are going to be used based on the same jobs/planned comp records.
What is the best practice in this regard, generally in US and other countries?

Hi,
Yes you can use.
Regards,
Kapil

How use two templantes with only one job ?

I have two templantes and want use with only one job.I use with input one xml data file !!
Is this possible?
Please Help!!
Thanks,
Bruno.

I probably missed this one earlier or felt that since it referenced an XML data file that I couldn't provide a definitive answer. I'm still not sure I can because we don't use XML for our data files, but use the "field nominated format". An expansion on Tammy's information: 1. use a multi-step job with each b task calling a different MDF. With this correction, it assumes that you either have access to set up the tasks/jobs yourself or can convince your Central administrator to do so. What happens is that TASKA is set up to reference FORMA and TASKB is set up to reference FORMB. Then a job is set up that causes both TASKA & TASKB to be ran. This will likely result in two different print files being sent to the printer. That may or may not be desirable, depending on whether your printer is set up to do something special between each print file (insert separator page, offset, whatever). Personally, I don't recommend this as it can quickly cause an unnecessary proliferation of tasks and jobs (we print 100's of differing form combinations with a single job definition). 2. I can't really address this as I didn't even know that a single form could cause another to be called. I would expect that unless the "base" form (say it is FORMA) is to always print with the secondary form (FORMB) it is restrictive and has the potential to cause a proliferation of FORMA files for the various combinations that are to be printed. Maybe it is possible to have logic to check the value of a data field to control what forms get called. 3. If you pass the XML file through a translation step and then through the transformation agent (maybe it can be done in a single step) this should work. It does add another step to the job as well as requiring learning to use the transformation agent. Depending on the combination of forms to be printed, you might need a different translation definition for each one, or at the very least have a data field that you can check the value of to determine what ^form commands to put in the output file. 4. My recommendation is based on assuming an XML data file has the same capabilities as a field nominated file. Within a field nominated file are various print agent commands, including references to data as well as which forms are to be printed (and a whole bunch of other commands). An XML file should have the same features - I just can't say what they might look like. If your current data file has no "form" reference but depends on the job/task definition you might have to stick with option 1. If it has a "form" reference, then you just need to insert additional references for additional forms. Then it is up to the source of your data (or a transformation agent step) to specify which forms are to be printed. For example, in field nominated format, the file might look like: ^job XYZ additional parameters ^form FORMA.MDF ^field FIELD1 data ^field FIELD2 data ^form FORMB.MDF ^field FIELD1 data ^field FIELD3 data or it might look like the way our files look: ^job XYZ additional parameters ^global FIELD1 data ^global FIELD2 data ^global FIELD3 data ^form FORMA.MDF ^form FORMB.MDF As you can see in the first example, there is a reference to the form followed by all fields that go on it followed by another form reference with the fields that go on it. This particular method, using all "^field" commands for defining the data requires that data duplicated between the forms be duplicated. (Or, the use of some ^global commands like the following.) In the second example, all data is defined first using the "^global" command followed by all of the form references. This allows for the data to be defined only once. If there is something unique regarding a particular form the field can be ^global at the beginning or it can be ^field b after the ^form reference (similar to the first example). As previously mentioned, the XML file should have the same capability but in XML notation, something like the following (forgive me as it has been years since I took the XML class and don't use it in my daily work so the actual format could be wrong, not to mention the actual labels): <job name=XYZ,option=aaaa,option=bbbbbbb> <form name=FORMA.MDF> <field name=FIELD1, value=xxxxxxxxxxx></field> <field name=FIELD2, value="xxxxxxxxxxxxx"></field> </form> <form name=FORMA.MDF> etcetera </job> or maybe: <job name=XYZ,option=aaaa,option=bbbbbbb> <global name=FIELD1,value=xxxxxxxxxxxx></global> <global name=FIELD2,value="xxxxxxxxxxxxx"></global> etcetera <form name=FORMA.MDF></form> <form name=FORMB.MDF></form> </job> or even (but I doubt it): <job name=XYZ,option=aaaa,option=bbbbbbb> <globals> name=FIELD1,value=xxxxxxxxxxxxxxxx, name=FIELD2,value="xxxxxxxxxxxxxxx" </globals> <forms> name=FORMA.MDF, name=FORMB.MDF </forms> </job>

My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

http://support.apple.com/kb/TS2005
http://support.apple.com/kb/HT1861
https://ssl.apple.com/support/proapps/serialnumbers/

Wifi sync 2 iPhones in one iTunes with different Apple-ID's.

Wifi sync 2 iPhones in one iTunes with different Apple-ID's. My Phone will show up in iTunes, my wife's wont. After plugging my wife's phone into my Win 8.1 pc and check Sync over wifi, I hit the eject button, could this be the reason? Or might it be the different Apple-ID's? If the answer is the first, is there any way tohave iTunes forgetmy wife's phone so I can addit from scratch?

Ello,
I know this, but thats in the past now sadly. The question is: Why wont my wife's iPhone show up in iTunes via wifi?
Is it because I pushed the eject button? And if so, is there any way I can make iTunes forget my wife's iPhone and *** it from scratch again?
Or is it because the phones uses different Apple-ID's?

One Key FIgure in more than one column with different restrictions

Hi,
I am using a key figure in more than one column with different restrictions, but restriction in one column is affecting the result in other column. What shall i do to make it independent from one another??

Hi Pravender Chauhan,
If you want in Single column different value for different Rows based on same Key Figure, you can create Structure where you can define different logic for each row but using same key figure.
If you want to use different Key figures then you should have to Restricted Key Figure and for any calculation you can use calculated Key figure.
Assign points if Useful.
Regards,
Rajdeep.

I have 2 Apple iPads with the same Apple account name. How do I set up one with a different Apple account name?

I have 2 iPads with the same Apple account name. How do I set up one with a different Apple name?

Why is the reason you want a different apple id on them? Need more details to make sure we don't accidently set up the self destruct feature and destory the planet.

Is there a way to view all favorites on one page from different albums?

is there a way to view all favorites on one page from different albums?
I can't seem to figure out how to view all favorites at one time.
nothing (thus far) is shared.
paid membership to revel, also.

oops - apparently you can do this from the app,
but not from the web login view.

One job with two steps - how to create one single spool?

Hello experts,
I have created two queries in SQVI. One is based on the table BSIK, the other on on BSAK.
The report layout is the same in both queries.
Now I schedule one job in SM36/SM37 with two steps corresponding to my queries.
I want my second step to append the spool created in the first step. Is that possible?
In order to do this I unchecked "New spool request" in the request attributes for the second step of the job.
I use the same printer, the same format (X_65_80), but it doesnt work.
The help on the field says
".... name, output device, number of prints and the format must match..." - What "name" do they mean?
"In addition, the existent spool order must not already be competed. This can occur if a spool is released for output...." - I use "send to SAP spooler only" option, is that what thay mean? How cen you have an "uncompleted spool" in the job.
If anybody knows ho to do this (without development!), please advise
Best regards,
Fatima

Hi,
Please do following steps :
1. Go to transaction code SM36
2. Do as per below screen shots
You can see Job steps is empty
Click on (Check and Save)
Next Screen
You can see one step created
Click on Create
You can see above it is showing as Step 2
Give again program name and variant
Click on (Check and Save)
You can see two steps are created
Go back (green arrow)
You can see know SAP is showing 2 Step(s) successfully defined which was earlier blank
Click on
Next Screen
Now schedule job as per your requirement.
Prerequisite create variants for both the programs as we need to mention the same .
Hope, this solves your issue else revert.
Regards,
Tejas

Is it possible to display one table on different sheets?

I'd like to use one table on different sheets.
On these sheets are also other tables, but one should be the same on each sheet.
Is this possible?

You can make one table refer to (take data from) another.
Here is a simple example where I made a table named "Source" and duplicated the table and named is "Destination-1".
the table "Destination-1" refers to table 1 like this:
A1=Source :: A1
copy cell A1 in the table "Destination-1" , then select ALL cells using the menu item "Edit > Select All", then paste
you may now duplicate this table to make additional "copies" as needed. To duplicate a table, select the table, then select the menu iten "Edit > Duplicate"
NOTE: you should be aware that data flows FROM the table "Source" to the destination tables-- NOT the other way.

Multiple idocs in Single Job behaves differently (RBDAPP01)

Hi,
How to debug the background Job for Program RBDAPP01 which already posted the Idocs in 53 status from 64.
I wanted to analyze why multiple idocs in same job behave differently than the single idoc in a job. In case of multiple idocs in a single job i put packet size 1, but no help.
Thanks,
Asit Purbey.

I found the solution, so closing this Post.

I am trying to save one picture in different versions- How do I do that- there is nothing that allows me to save as

I am trying to save one picture in different versions- How do I do that- there is nothing that allows me to save as- How do I do that??

http://www.apple.com/aperture/
Regards
TD

Splitting a background job over different application servers

I am running my program in the background and its taking long to complete. I have done some optimizations and it has greatly improved but still not running as fast as I want because its processing large amounts of data and the amount of time that I want all the data to be processed is little compared to the runtime of the program so now I want to split the background job over different application servers. Can someone tell me how do I go about doing that and example ABAP code will be greatly appreciated.
Many thanks

Hello, If you are interested in BANK_PP_JOBCTRL, here are some of the inputs. Its work very efficeintly, though you will have to investigate a little bit froom your end.
With in package bank_pp_jobctrl , you will find these FM. I have mentioned the use of it as well.
RBANK_PP_DEMO_GENERATE_DATA: To create the Business data for Parallel Processing.
RBANK_PP_DEMO_CREATE_PACKMAN: To create Packages out of the business data.
RBANK_PP_DEMO_START : To process data in parallel.
RBANK_PP_DEMO_RESTART: To re-process failed records during parallel Processing.
You will need to call above in your report program in the same sequence as shown above based on you requirement. I did used only first three.
TO generate events you will need to execute SE38: RBANK_PP_GENERATE_APPL to create application this will create the FM with numbers as shown below.
Events: This PPF automatically triggers various events during the execution of theStart Program. Each of this event is associated with a custom function module which contains the business logic.
For implementing this framework, at least the below mentioned methods should be implemented .
0205 – Create Package Templates : This method is used to write the logic for creating packages which in turn decides the data to be processed in parallel. This function module is called in loop at the loop ends only when the exporting parameter E_FLG_NO_PACKAGE has a value ‘X’ passed back to the Parallel processing framework.
1000 – Initialize Package :This method is the first step in processing a package. It fetches all the parameters required for the parallel processing to start. All the parameters are passed to this FM as importing parameters and it is the responsibility of this FM to save it in global parameters so that it can be utilized by Parallel processing framework.
1100 – Selection per Range : This method is used to read data for a package. The objects selected must be buffered in global data areas of the application for later processing. The package information is stored as interval in global parameters and this information is used to select the package specific data.
1200 – Selection for Known Object List: This method is used instead of method 1100 if it is a restart run. The objects to be processed are known already.
1300 – Edit Objects: The processing logic to be implemented using parallel processing for the selected objects is written in this method. This function module is used to implement the business logic and
Also, obiviously you would like to log your messages , so the framwrok provides macros to do it.
Let me know if you need some further help as I know there is very little information provided on this.
Regards/Ajay

Canon iRC4580, One Job to different Papertrays

Similar Messages

Maybe you are looking for