Canon MP640 is not found via wireless using canonijnetwork tool

MacBook Pro late 2008. OS X (10.5.8)
BT home hub
Canon Pixma MP640 wireless printer.
Printer set up wifi connection to wireless BT homehub without any problems. Confiremed wirelss LAN settings via printer display.
Ran setup disk M1.1 successfully installing drivers. On Canon IJ Network Tool screen, an alert message appears stating "printer not detected".
I have tried adding it through system preferences > print & fax > clicking + tab. Two printers are displayed: Canon MP640 series ...Bonjour; Canon MP640 series canonijnetwork.
I added both printers, but they only appear as USB in the utilities tab. I changed it to network, then selected Canon MP640 series canonijnetwork (only option displayed). Try to print and the dialogue box appears for the printer, stating it is printing, yet nothing prints.
I typed the IP address into safari and checked the settings everything is enabled and IPV4 is being used.
Have been to canon website and downloaded their drivers but when I open them message states cannot be opened on this operating system.
How do you connect this printer via wireless?
Thanks,
Sally

1. Have you restarted your Mac since installing the printer? Canon-installed software starts automatically (actually for scanner operation) that shows a pop-up to confirm that I want to use the wireless Canon installation during the start process.
Canon isn't clear in communicating that to print wirelessly, you are actually installing the printer as a (WiFi) wireless device on your network hub. Then when you print, your Mac first communicates with the network hub, and then the hub communicates with the printer. So, your BT hub must be on in order to print. (My Canon MP560 works the same way.)
Have you followed the Canon network printing troubleshooting guide available here? --> http://www.usa.canon.com/cusa/support/consumer/printersmultifunction/pixma_mp_series/pixmamp640#BrochuresAndManuals
When installed correctly, your printer should appear in your list of installed printers as a Canon MP640 *with a 6-character hexadecimal address*, such as "Canon MP640 F9A3B1" THAT is the network printer.
You can rename it later, if you so desire. The 6 hexadecimal characters are the last 6 digits of the printer's network hardware address. I(t's called a MAC address, but it has nothing to do with Macintosh.)
The 'Canon MP640 series' setup you have installed can ONLY be accessed via a USB cable, and as you discovered, you cannot change the interface. If you have no need for a USB connection, you can delete that print setup from print/fax preferences.

Similar Messages

CRM 7.0 upgrade ( i5/OS PASE program not found or in use)

Hi,
We are upgrading CRM 5.0 to CRM 7.0 on iSeries (V6r1) and facing the following issue.
When I execute this command
   STARTUP    SID(CD3) TYPE(ABAP) RESTART(YES) DVDPATH('/Inst_DVDs/51036889')
        SAPUPLIB(SAPUP) OPTIONS('jce_policy_zip=/Inst_DVDs/51036889/local_policy.jar')
iSeries show this error message in "UPG_A_CD3" job log.
   Message . . . . :   i5/OS PASE program not found or in use. Path name is
       /usr/sap/CD3/upg/STARTUP.
Does anyone has any idea what could be wrong ?
Thank you,
Jack.

Hi,
We are upgrading CRM 5.0 to CRM 7.0 on iSeries (V6r1) and facing the following issue.
When I execute this command
   STARTUP    SID(CD3) TYPE(ABAP) RESTART(YES) DVDPATH('/Inst_DVDs/51036889')
        SAPUPLIB(SAPUP) OPTIONS('jce_policy_zip=/Inst_DVDs/51036889/local_policy.jar')
iSeries show this error message in "UPG_A_CD3" job log.
   Message . . . . :   i5/OS PASE program not found or in use. Path name is
       /usr/sap/CD3/upg/STARTUP.
Does anyone has any idea what could be wrong ?
Thank you,
Jack.

I want to disable 'Spotlight' for repairing my disk "Macintosh HD" , but somehow the command 'sudo mdutil -a -i off' does not work in 'Terminal'. I get result as ' bash: sudo: command not found' .I am using OS 10.10. Please help.

I want to disable 'Spotlight' for repairing my disk "Macintosh HD" , but somehow the command 'sudo mdutil -a -i off' does not work in 'Terminal'. I get result as ' bash: sudo: command not found' .I am using OS 10.10. Please help.

It appears that you may not have a properly installed OS X system.
You must be connected to the Internet to reinstall OS X.
In the menu bar, choose Apple menu > Restart. Once your Mac restarts (and the gray screen appears), hold down the Command (⌘) and R keys.
Select “Disk Utility,” and then click Continue.
Select your startup disk from the list on the left, and then Repair Disk.
After disk is repaired, select Reinstall OS X, then click Continue.
Follow the onscreen instructions. In the pane where you select a disk, select your current OS X disk

Trying to transfer a video clip from iPhone to iPad using transfer app it says device not found, I have used this before wifi is fine and both devices are connected ?

Trying to transfer a video clip from iPhone to iPad using transfer app it says device not found, I have used this before wifi is fine and both devices are connected ?

That does not involve iPhoto for the Mac in any way - try the iPad forum
I will request your post be moved
LN

Canon PIXMA MP600R - not working in wireless mode since installing 10.6.1

I have a Canon PIXMA MP600R which was set up to use over a wireless network and was working completely 100%.
However I installed Snow Leopard two weeks ago and now the printer wont work wirelessly. I have reinstalled the printer three times now, downloaded the printer updates from Apple and still no joy. I have trawled through the help file and the Canon PIXMA MP600R manual and have still not managed to connect wirelessly even though all the criteria's are met - access point, network configuration etc. The printer does not display in the Utility Printer Network List only in the USB list. When trying to connect to the printer to the router the message 'Printer cannot be found' pop up comes up even though all MAC, IP address, network access are met... any ideas?

Not sure why this is giving you so much trouble but I believe the MP600R will work fine on Snow Leopard once we get the machine correctly configured. I think I made an assumption that you were printing fine via wireless with another version of Mac OS X. But given that the printer does not appear to have/had an IP address set, then it would suggest that you were not printing previously via wireless. Is this correct?
To configure the IP address in the MP600R you have to connect the printer to the Mac via USB. Then you select the USB attached MP600R in the Printers list and open the Options & Supplies > Printer Utility. This will open the Canon IJ Printer Utility. Here you select the MP600R and now the Network Settings button should appear. If the button is still not present then you may have to download and install the Canon IJ Network Utility v2.70. In testing 10.6, my printers have already been configured for the network so I have never needed to do this setup step and therefore I am not certain if the facility exists to configure the network settings without this tool being installed. Apologies if this has been the stumbling block.
Once you have the Network Settings button present, select it and go through the procedures to configure the network settings. Once this process has completed, the setup will prompt you to turn off the MP600R and then disconnect the USB cable. Then when you power the MP600R back on, the machine should be connected to your wireless access point. At this stage you can check that the MP600R has an IP address via the Device Settings menu on the printer (refer back to my third reply to check how this is done).
Once the printer has an IP address and shows that it is active, you can now add another printer queue, this time for the wireless connected MP600R. Open Print & Fax, select to Add and choose the Default view. As I said in the first reply, you will probably see the MP600R immediately as a Bonjour Scanner, but we need to wait until the MP600R appears with its Kind column showing 'canonijnetwork'. When this does appear, select it and the Print Using menu will automatically find the correct driver. Click Add to finish adding the network printer queue.
Hope this stops the hair reduction....
Pahu

Class not found in applet using 2 jar files

I have an applet which has been working for years as a stand alone or connecting directly to a derby database on my home server. I have just changed it to connect to MySQL on my ISP server via AJAX and PHP.
I am now getting a class not found error in my browser, probably because I'm stuffing up the class path.
The HTML I am using to call the applet is:
<applet code="AMJApp.class"
codebase="http://www.interactived.com/JMTalpha"
archive="AMJ014.jar,plugin.jar"
width="500"height="500"
MAYSCRIPT style="border-width:0;"
name="jsap" id="jsap"></applet>The AMJ014.jar contains the applet and supporting class files.
The error message is strange to me because it refers to a class I noticed on another web page but which has nothing to do with my applet. Anyway, the message in full is:
load: class NervousText.class not found.
java.lang.ClassNotFoundException: NervousText.class
     at sun.plugin2.applet.Applet2ClassLoader.findClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass0(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadCode(Unknown Source)
     at sun.plugin2.applet.Plugin2Manager.createApplet(Unknown Source)
     at sun.plugin2.applet.Plugin2Manager$AppletExecutionRunnable.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
Exception: java.lang.ClassNotFoundException: NervousText.class
java.lang.UnsupportedClassVersionError: AMJApp : Unsupported major.minor version 51.0
     at java.lang.ClassLoader.defineClass1(Native Method)
     at java.lang.ClassLoader.defineClassCond(Unknown Source)
     at java.lang.ClassLoader.defineClass(Unknown Source)
     at java.security.SecureClassLoader.defineClass(Unknown Source)
     at java.net.URLClassLoader.defineClass(Unknown Source)
     at java.net.URLClassLoader.defineClass(Unknown Source)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
     at java.lang.reflect.Method.invoke(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.defineClassHelper(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.access$100(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader$2.run(Unknown Source)
     at java.security.AccessController.doPrivileged(Native Method)
     at sun.plugin2.applet.Plugin2ClassLoader.findClassHelper(Unknown Source)
     at sun.plugin2.applet.Applet2ClassLoader.findClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass0(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at sun.plugin2.applet.Plugin2ClassLoader.loadCode(Unknown Source)
     at sun.plugin2.applet.Plugin2Manager.createApplet(Unknown Source)
     at sun.plugin2.applet.Plugin2Manager$AppletExecutionRunnable.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
Exception: java.lang.UnsupportedClassVersionError: AMJApp : Unsupported major.minor version 51.0

Thanks again.
The page code is:
<html>
<head>
<title>Applet to JavaScript to PHP</title>
</head>
<body>
<script type="text/javascript">
function updateWebPage(myArg)
document.getElementById("txt1").innerHTML=myArg;
if (myArg=="")
document.getElementById("cbxItem").innerHTML="";
return;
if (window.XMLHttpRequest)
{// code for IE7+, Firefox, Chrome, Opera, Safari
xmlhttp=new XMLHttpRequest();
else
{// code for IE6, IE5
xmlhttp=new ActiveXObject("Microsoft.XMLHTTP");
xmlhttp.onreadystatechange=function()
if (xmlhttp.readyState==4 && xmlhttp.status==200)
    document.getElementById("cbxItem").innerHTML=xmlhttp.responseText;
xmlhttp.open("GET","putitem.php?id="+myArg,true);
xmlhttp.send();
</script>
<form>
<table border=1 align='center' cellpadding=0 cellspacing=0 >
<tr><td style='text-align:center; background-color:#C0C0C0'>Compiled Java Applet</td></tr>
<tr><td><applet code="AMJApp.class" codebase="http://www.interactived.com/JMTalpha" archive="AMJ014.jar" width="500"height="500" MAYSCRIPT style="border-width:0;" name="jsap" id="jsap"></applet> </td></tr>
<tr><td style='text-align:center; background-color:#C0C0C0'>HTML Textbox filled by JavaScript</td></tr>
<tr><td><textarea style='width:500px; height:50px' name='txt1' id='txt1'>Query goes here</textarea></td></tr>
<tr><td style='text-align:center; background-color:#C0C0C0'>HTML diagnostic messages rendered by PHP script</td></tr>
<tr><td><div id="cbxItem">PHP info will populate this space</div></td></tr>
</table>
</form>
</body>
</html>The URL of the problem page is:
http://www.interactived.com/JMTalpha/AMJTest.htm
The code in the page is based on the following test page, which works:
http://www.interactived.com/test5Applet.htm
And the Applet, before I made any changes can be seen at this address:
http://www.interactived.com/jartest0906.htm
Thanks again for you interest.
Edited by: 886473 on 21-Sep-2011 00:47

Help! 'Page not found error' when use the word 'account' on my web page!

I have encountered the weirdest problem when making some changes to my website.
When adding text within the <p></p> tags everything is fine until I type the word 'account' or 'accounts' then I get a 'page not found' error.
Any other text can go between those tags, only the word 'account' causes the problem.
Any ideas?
(I am using Dreamweaver MX 2004 and its a PHP page)
I am so confused on this one, so any help would be much appreciated!
Thanks.

http://www.reformationassociates.com/ - This is the website, the weirdest part is, it is only happening on pages after they have been opened through Dreamweaver, so it's only once I access them that the problem occurs, I dont have to make any changes, just open them and they suddenly show up as 'page not found'.
http://www.reformationassociates.com/archive/Pinnacle.php is one of the pages that was accessed yesterday via Dreamweaver and we have had to change the word to 'acct' to stop the 'page not found' error.
Afriad I dont know what SSI files are? sorry....
Thanks.

Getting 'File not found' error while using server object model code

Hi,
I am using server object model code to pull list data in a console application. My machine has standalone installation of SP 2010. I am getting error 'File Not Found', however the same operation is working fine with client object model code.
Code I am using:
string strURL=http://servername/sites/sitename;
SPSite siteObj=new SPSite (strURL); //getting error here.
I have already checked the below,
1. Framework being used is 3.5.
2. I have proper access to site.
3. Running visual studio as admin.
Any help is much appreciated.
thanks
Tarique
thanks and regards Tarique Aslam

Hello Tarique ,
Couple of pints need to check:
1. User running the console application needs to have at least read permission to the SharePoint databases
2. Set application by changing the "Platform target:" option on the "Build" to "Any CPU"
Also refer this similar thread:
http://social.msdn.microsoft.com/Forums/sharepoint/en-US/2a419663-c6bc-4f6f-841b-75aeb9dd053d/spsite-file-not-found
Hope it could help
Hemendra:Yesterday is just a memory,Tomorrow we may never see
Please remember to mark the replies as answers if they help and unmark them if they provide no help

ResourceAdapter not found during deployment using WL 7.0 SP2

Hi,
          Am using WL 7.0 SP2 on Win2k w/ JDK 1.4.
          Am using the non-managed mode (wherein the admin server is also the managed-server).
          Am trying to deploy my RA. On uploading the RAR using
          the admin console, I get the following error (from the server.log):
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Deployer Initiating a deployment task with id 8 for application bs-ra
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Deployer preparing application bs-ra on vspl-dev-server
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Deployer prepared application bs-ra on vspl-dev-server
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Management Configuration changes for domain saved to the repository.
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Deployer activating application bs-ra on vspl-dev-server
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info Connector Initializing connection pool for resource adapter BookStore-
          Resource Adapter_eis/BSResourceAdapter.
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Error Deployer Unexpected error was encountered during the deployment proce
          ss.
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Error Deployer The Slave Deployer failed to complete the deployment task wi
          th id 8 for the application bs-ra.
          java.lang.NoClassDefFoundError: javax/resource/spi/ResourceAdapter
               at java.lang.Class.getMethods0(Native Method)
               at java.lang.Class.getDeclaredMethods(Class.java:1034)
               at java.beans.Introspector$1.run(Introspector.java:847)
               at java.security.AccessController.doPrivileged(Native Method)
               at java.beans.Introspector.getPublicDeclaredMethods(Introspector.java:845)
               at java.beans.Introspector.getTargetEventInfo(Introspector.java:551)
               at java.beans.Introspector.getBeanInfo(Introspector.java:289)
               at java.beans.Introspector.getBeanInfo(Introspector.java:76)
               at weblogic.connector.common.internal.ConnectionPool.<init>(ConnectionPool.java:402)
               at weblogic.connector.common.internal.ConnectionPoolManager.addManagedConnectionFactory(ConnectionPoolManager.java:64)
               at weblogic.connector.deploy.ConnectorDeployer.activate(ConnectorDeployer.java:315)
               at weblogic.connector.deploy.ConnectorModule.activate(ConnectorModule.java:221)
               at weblogic.j2ee.J2EEApplicationContainer.activateModule(J2EEApplicationContainer.java:1662)
               at weblogic.j2ee.J2EEApplicationContainer.activate(J2EEApplicationContainer.java:1087)
               at weblogic.j2ee.J2EEApplicationContainer.activate(J2EEApplicationContainer.java:1074)
               at weblogic.management.deploy.slave.SlaveDeployer.processPrepareTask(SlaveDeployer.java:1110)
               at weblogic.management.deploy.slave.SlaveDeployer.prepareUpdate(SlaveDeployer.java:730)
               at weblogic.drs.internal.SlaveCallbackHandler$1.execute(SlaveCallbackHandler.java:24)
               at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:213)
               at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:189)
          --------------- nested within: ------------------
          weblogic.management.ManagementException: 149233 - with nested exception:
          [java.lang.NoClassDefFoundError: javax/resource/spi/ResourceAdapter]
               at weblogic.management.deploy.slave.SlaveDeployer.convertThrowable(SlaveDeployer.java:834)
               at weblogic.management.deploy.slave.SlaveDeployer.processPrepareTask(SlaveDeployer.java:1180)
               at weblogic.management.deploy.slave.SlaveDeployer.prepareUpdate(SlaveDeployer.java:730)
               at weblogic.drs.internal.SlaveCallbackHandler$1.execute(SlaveCallbackHandler.java:24)
               at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:213)
               at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:189)
          Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Warning Deployer Failures detected initiating weblogic.management.ManagementE
          xception: 149233 - with nested exception:
          [java.lang.NoClassDefFoundError: javax/resource/spi/Resource
                                                                                              Adapter] task for application Activate application bs-ra on
          vspl-dev-server
          Jun 9, 2003 5:32:32 PM EDT vspl-dev-server Info Management Configuration changes for domain saved to the repository.
          Jun 9, 2003 5:32:36 PM EDT vspl-dev-server Error Connector ManagedConnectionFactory not found for jndiName eis/BSResour
          ceAdapter.
          Jun 9, 2003 5:32:39 PM EDT vspl-dev-server Error Connector ManagedConnectionFactory not found for jndiName eis/BSResour
          ceAdapter.
          Jun 9, 2003 5:32:47 PM EDT vspl-dev-server Error Connector ManagedConnectionFactory not found for jndiName eis/BSResour
          ceAdapter.
          Jun 9, 2003 5:32:48 PM EDT vspl-dev-server Error Connector ManagedConnectionFactory not found for jndiName eis/BSResour
          ceAdapter.
          There are two things I observer here.
          1. The ResourceAdapter class does not seem to be found by Weblogic. It's part of the javax.resource.spi package.
          I checked the weblogic.jar archive in the WL-HOME/server/lib folder. It does not seem to have the class. Why ?
          2. It complains about the ManagedConnectionFactory not being found. Am assuming that if the RA was deployed
          in the first place, I would not have seen this error (coz, the ManagedConnectionFactory would have been
          deployed in the previous step). Right ?
          I did observe that WL 7.0 supports only JCA 1.0. In JCA 1.0's (public) API, there is no mention of the
          javax.resource.spi.ResourceAdapter class, though the spec talks about it. ??
          Note: I had designed and implemented my RA as per JCA 1.5 (but nothing 1.5-specific, I guess).
          Any ideas ?
          thanks,
          raghu


I figured it out. Darn simple.
          My ManagedConnectionFactory implementation referenced ResourceAdapter as
          it has to implement the ManagedConnnectionFactory interface of JCA 1.5.
          In JCA 1.0 (which is supported by WL 7.0 & 8.1), the ResourceAdapater
          is undefined. Hence, the classloading problem.
          Sorry for any confusion.
          raghu
          raghu h wrote:
          > Hi,
          >
          > Am using WL 7.0 SP2 on Win2k w/ JDK 1.4. Am using the non-managed mode
          > (wherein the admin server is also the managed-server).
          >
          > Am trying to deploy my RA. On uploading the RAR using
          > the admin console, I get the following error (from the server.log):
          >
          >
          >
          > -----------------------------------------------------------------------------------------------------------------
          >
          >
          > Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info
          > Deployer Initiating a deployment task with id 8 for
          > application bs-ra
          > Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Info
          > Deployer preparing application bs-ra on
          > vspl-dev-server Jun 9, 2003 5:32:31 PM EDT
          > vspl-dev-server Info Deployer prepared application
          > bs-ra on vspl-dev-server Jun 9, 2003 5:32:31 PM EDT
          > vspl-dev-server Info Management Configuration
          > changes for domain saved to the repository. Jun 9, 2003 5:32:31 PM
          > EDT vspl-dev-server Info Deployer activating
          > application bs-ra on vspl-dev-server Jun 9, 2003 5:32:31 PM
          > EDT vspl-dev-server Info Connector
          > Initializing connection pool for resource adapter BookStore-
          >
          > Resource Adapter_eis/BSResourceAdapter.
          >
          > Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Error
          > Deployer Unexpected error was encountered during the
          > deployment proce
          >
          > ss.
          >
          > Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Error
          > Deployer The Slave Deployer failed to complete the deployment
          > task wi
          >
          > th id 8 for the application bs-ra.
          >
          > java.lang.NoClassDefFoundError: javax/resource/spi/ResourceAdapter
          > at java.lang.Class.getMethods0(Native Method)
          > at java.lang.Class.getDeclaredMethods(Class.java:1034)
          > at java.beans.Introspector$1.run(Introspector.java:847)
          > at java.security.AccessController.doPrivileged(Native Method)
          > at
          > java.beans.Introspector.getPublicDeclaredMethods(Introspector.java:845)
          > at java.beans.Introspector.getTargetEventInfo(Introspector.java:551)
          > at java.beans.Introspector.getBeanInfo(Introspector.java:289)
          > at java.beans.Introspector.getBeanInfo(Introspector.java:76)
          > at
          > weblogic.connector.common.internal.ConnectionPool.<init>(ConnectionPool.java:402)
          >
          > at
          > weblogic.connector.common.internal.ConnectionPoolManager.addManagedConnectionFactory(ConnectionPoolManager.java:64)
          >
          > at
          > weblogic.connector.deploy.ConnectorDeployer.activate(ConnectorDeployer.java:315)
          >
          > at
          > weblogic.connector.deploy.ConnectorModule.activate(ConnectorModule.java:221)
          >
          > at
          > weblogic.j2ee.J2EEApplicationContainer.activateModule(J2EEApplicationContainer.java:1662)
          >
          > at
          > weblogic.j2ee.J2EEApplicationContainer.activate(J2EEApplicationContainer.java:1087)
          >
          > at
          > weblogic.j2ee.J2EEApplicationContainer.activate(J2EEApplicationContainer.java:1074)
          >
          > at
          > weblogic.management.deploy.slave.SlaveDeployer.processPrepareTask(SlaveDeployer.java:1110)
          >
          > at
          > weblogic.management.deploy.slave.SlaveDeployer.prepareUpdate(SlaveDeployer.java:730)
          >
          > at
          > weblogic.drs.internal.SlaveCallbackHandler$1.execute(SlaveCallbackHandler.java:24)
          >
          > at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:213)
          > at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:189)
          > --------------- nested within: ------------------
          > weblogic.management.ManagementException: 149233 - with nested exception:
          > [java.lang.NoClassDefFoundError: javax/resource/spi/ResourceAdapter]
          > at
          > weblogic.management.deploy.slave.SlaveDeployer.convertThrowable(SlaveDeployer.java:834)
          >
          > at
          > weblogic.management.deploy.slave.SlaveDeployer.processPrepareTask(SlaveDeployer.java:1180)
          >
          > at
          > weblogic.management.deploy.slave.SlaveDeployer.prepareUpdate(SlaveDeployer.java:730)
          >
          > at
          > weblogic.drs.internal.SlaveCallbackHandler$1.execute(SlaveCallbackHandler.java:24)
          >
          > at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:213)
          > at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:189)
          > Jun 9, 2003 5:32:31 PM EDT vspl-dev-server Warning
          > Deployer Failures detected initiating
          > weblogic.management.ManagementE
          >
          > xception: 149233 - with nested exception:
          >
          > [java.lang.NoClassDefFoundError: javax/resource/spi/Resource
          >
          > Adapter] task for application Activate application bs-ra on
          >
          > vspl-dev-server
          >
          > Jun 9, 2003 5:32:32 PM EDT vspl-dev-server Info
          > Management Configuration changes for domain saved to the
          > repository. Jun 9, 2003 5:32:36 PM EDT vspl-dev-server
          > Error Connector ManagedConnectionFactory not found for
          > jndiName eis/BSResour
          >
          > ceAdapter.
          >
          > Jun 9, 2003 5:32:39 PM EDT vspl-dev-server Error
          > Connector ManagedConnectionFactory not found for jndiName
          > eis/BSResour
          >
          > ceAdapter.
          >
          > Jun 9, 2003 5:32:47 PM EDT vspl-dev-server Error
          > Connector ManagedConnectionFactory not found for jndiName
          > eis/BSResour
          >
          > ceAdapter.
          >
          > Jun 9, 2003 5:32:48 PM EDT vspl-dev-server Error
          > Connector ManagedConnectionFactory not found for jndiName
          > eis/BSResour
          >
          > ceAdapter.
          >
          > -------------------------------------------------------------------------------------------------------------
          >
          >
          >
          > There are two things I observer here. 1. The ResourceAdapter class does
          > not seem to be found by Weblogic. It's part of the javax.resource.spi
          > package.
          > I checked the weblogic.jar archive in the WL-HOME/server/lib folder. It
          > does not seem to have the class. Why ?
          > 2. It complains about the ManagedConnectionFactory not being found. Am
          > assuming that if the RA was deployed
          > in the first place, I would not have seen this error (coz, the
          > ManagedConnectionFactory would have been
          > deployed in the previous step). Right ?
          >
          > I did observe that WL 7.0 supports only JCA 1.0. In JCA 1.0's (public)
          > API, there is no mention of the
          > javax.resource.spi.ResourceAdapter class, though the spec talks about
          > it. ??
          >
          >
          > Note: I had designed and implemented my RA as per JCA 1.5 (but nothing
          > 1.5-specific, I guess).
          >
          > Any ideas ?
          >
          > thanks,
          > raghu
          >
          >
          >
          >

My wireless keyboard is not found, My wireless keyboard is not found

My wireless keyboard is still not found after changing batteries. What can be wrong?

If you don't have a wired keyboard to do the following then, first, try restarting. Then if it is found and connected, go into Bluetooth Preferences and make sure it's setup and paired there. In addition, add it to Favorites by clickling on the small tools icon.
Next, check this box in Advanced. You can check Allow Bluetooth devices to wake this computer. Mine is unchecked because it may sometimes be responsible for waking the computer from sleep.
And you'll be far better off getting a decent wired keyboard. The Apple wireless ones eat batteries alive, and are prone to failure. I have one, but stuck it in a drawer right away, where it's been almost 4 years. Typing on it was horrid, as well.

Class Not Found Error when using Junit

Hi
I am using Junit4.1, Eclipse 3.2.1
I am getting this error
Class not found
start.test.TestPdfGenerationService
java.lang.ClassNotFoundException: start.test.TestPdfGenerationService
     at java.net.URLClassLoader$1.run(URLClassLoader.java:200)
     at java.security.AccessController.doPrivileged(Native Method)
     at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:306)
     at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:268)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:251)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.loadClass(RemoteTestRunner.java:683)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.loadClasses(RemoteTestRunner.java:425)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:445)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:673)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:386)
     at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:196)
what would the possible reason for that and how can i come out of it..

the reason: the class is not in the classpath. Or the project's runtime classpath.
Make sure it's added to the build path and if necessary exported all the way to your JUnit project.

Class not found error while using ikvm error code IKVMC0100: class "javax.b

hi iam writing a java application which uses bluetoth i.e. javax.bluetooth;
now i need to create exe for c# i.e. my GUI is C# and business logic is java,
so these are steps i have followed
* created a java project (iam using netbeans 6.1)
* after build i used command prompt and travesed to dist of my project location which contains jar
* here i typed ikvmc my.jar
but now it says the following it also contains others but one of such is
Warning IKVMC0100: class "javax.bluetooth.LocalDevice" not found
it also creates exe but if use that in my c# then raises the exception...
so please help me.. what is the solution for this....

If you have the SDKPanel sample, you have a Flex sample and debugging information. Please let me know (off-forum) what you're buildng, and we'll make sure your dev environment is configured correctly.

Class not found error when using javah

Im just trying to create a simple hello world program using jni however I already got stuck trying to create the c header file when I run the javah program. It keeps telling that the class is not found but the class is in the local directory. Should a classpath be set or are there other things that I am missing?

You should have a classpath pointing to the local directory.

HTTP 404 Not Found Error when using htp.anchor

Hi All,
We have customized hire flow and Oracle aplication 11i and added some HTML pages from PL/SQL. We are receiving "HTTP 404 Not Found Error" intermittently when clicking on submit button to go to the next page. If we close the browser and perform the same transaction it is working fine.
Can you please help us in troubleshooting this issue.
Thanks & Regards,
Veerababu.

If you are using Apache, check the error log for more details about the 404. If you are using EPG, there are similar logs somewhere but I can't tell you where off-hand.
Scott

FormTemplate not found Exception while using adobe Services

Hi,
We are trying to create a pdf file using Adobe Services from webDynpro.
However, in doing so, we get an error saying-
"The error is:
com.sap.tc.webdynpro.services.exceptions.WDRuntimeException:
FormTemplate was not found"
Followed by the message-
java.io.FileNotFoundException: ./temp/webdynpro/public/asianpaints.com/login_form_using_adobe/webdynpro/Components/com.apl.test.login_form_using_adobe.LoginForm/PdfForm_InteractiveForm.xdp (No such file or directory
(errno:2))
at java.io.FileInputStream.open(Native Method)
at java.io.FileInputStream.<init>(FileInputStream.java:106)
at
com.sap.tc.webdynpro.clientserver.adobe.AdobeFormHelper.getTemplateURL
(AdobeFormHelper.java:659)
However, the PdfForm_InteractiveForm.xdp (template Source) file exists
in the specified position.We are using Adobe Reader 6.0 on NWD04
Could you please let us know the solution to this problem at the
earliest as we are in the midst of the development.
Thanks in advance
Apeksha

Hi,
Thanks for the reply. I worked recreated the application by simple reinserting the interactive UI element and binding its dataSource context with a node whose values i need to display in the pdf format and pdfsource bound to attibute of type binary. However, when i deploy, i get the following exception:
Processing HTTP request to servlet [dispatcher] finished with error.
The error is: com.sap.tc.webdynpro.services.exceptions.WDRuntimeException: Error during call to AdobeDocumentServer: Failed to create a Data Manager. Please ensure that the Document Services Data Manager service is running:
com.adobe.FailedCreationException
Exception id: [001083FE64E6006900000218000010E80004194FC07D8B75]
However, the Document Services Data Manager service is already running along with IIOP provider.Are there some other things that need to be taken care of?
Thanks in Advance
Apeksha

Canon MP640 is not found via wireless using canonijnetwork tool

Similar Messages

Maybe you are looking for