Canon PIXMA MP600R - not working in wireless mode since installing 10.6.1

I have a Canon PIXMA MP600R which was set up to use over a wireless network and was working completely 100%.
However I installed Snow Leopard two weeks ago and now the printer wont work wirelessly. I have reinstalled the printer three times now, downloaded the printer updates from Apple and still no joy. I have trawled through the help file and the Canon PIXMA MP600R manual and have still not managed to connect wirelessly even though all the criteria's are met - access point, network configuration etc. The printer does not display in the Utility Printer Network List only in the USB list. When trying to connect to the printer to the router the message 'Printer cannot be found' pop up comes up even though all MAC, IP address, network access are met... any ideas?

Not sure why this is giving you so much trouble but I believe the MP600R will work fine on Snow Leopard once we get the machine correctly configured. I think I made an assumption that you were printing fine via wireless with another version of Mac OS X. But given that the printer does not appear to have/had an IP address set, then it would suggest that you were not printing previously via wireless. Is this correct?
To configure the IP address in the MP600R you have to connect the printer to the Mac via USB. Then you select the USB attached MP600R in the Printers list and open the Options & Supplies > Printer Utility. This will open the Canon IJ Printer Utility. Here you select the MP600R and now the Network Settings button should appear. If the button is still not present then you may have to download and install the Canon IJ Network Utility v2.70. In testing 10.6, my printers have already been configured for the network so I have never needed to do this setup step and therefore I am not certain if the facility exists to configure the network settings without this tool being installed. Apologies if this has been the stumbling block.
Once you have the Network Settings button present, select it and go through the procedures to configure the network settings. Once this process has completed, the setup will prompt you to turn off the MP600R and then disconnect the USB cable. Then when you power the MP600R back on, the machine should be connected to your wireless access point. At this stage you can check that the MP600R has an IP address via the Device Settings menu on the printer (refer back to my third reply to check how this is done).
Once the printer has an IP address and shows that it is active, you can now add another printer queue, this time for the wireless connected MP600R. Open Print & Fax, select to Add and choose the Default view. As I said in the first reply, you will probably see the MP600R immediately as a Bonjour Scanner, but we need to wait until the MP600R appears with its Kind column showing 'canonijnetwork'. When this does appear, select it and the Print Using menu will automatically find the correct driver. Click Add to finish adding the network printer queue.
Hope this stops the hair reduction....
Pahu

Similar Messages

Canon pixma mp600R not working after security update

Hi,
yesterday apple software update installed the last updates for my intel imac with 10.4.11. After that my canon printer is not working via airport. USB works fine. the networking utility sends and receive pings to the printer.
Tried to reinstall with the canon network tool. after checking of the airport signal (good) the printer utility open but I cannot add my printer, because its not shown.
does have anyone a idea to get the printer working wireless again?
P.S. My ibook prints pretty fine wireless to the canon. So its not a airport problem.

Hi Martin, try this...
Safe Boot off the HD & use Disk Utility from there to Repair Permissions, reboot once more.
Mac OS X: About the Reset Printing System feature ...
http://support.apple.com/kb/HT1341?viewlocale=en_US
Reinstall the Driver if need be.
Fix Permission before & after any SW update.

Computer not working in wireless mode

Being new to the Mac world I got everything when I bought my imac G5. I have a netgear modem and airport card but have never been able to work in "wireless" mode. Last week I brought my new work laptop home which automatically recognised my netgear equipment and I managed to log on to the internet through a wirless connection. How can I get my Mac to do this ?? (I am a bit of a technophobe so easy instructions are required !!)

Hi novice, and welcome to Apple Discussions.
Have you tried using AirPort Setup Assistant, which is in the Utilities folder inside your Applications folder? This will lead you through the necessary steps.
If you've already tried it and been unsuccessful, post back with more details.
H

Canon Pixma MP495 not working with mini

I'm trying to use the scanner on my Canon Pixma MP495 with my Mac Mini. The printer works okay, but when I click on the scanner, I get an error that says reopeon or okay - MP Navigator EX quit unexpectedly.

I would like to add I might have the problem solved.
I found an older Windows forum from 2009 where another person had a similar problem and it was suggested to use the add 'local printer'. Of course, the wizard set it up so not sure what it did but I did what they suggested and the scanner finally works.
Also, when I went to print something, the preview picture came up and the door to the printer popped open but one of my ink cartridges is out so it couldn't print.....bummer.
At least I never got the 'driver not installed correctly' message.
As soon as I get a chance to get some more ink and try it, I'll post the results.
**fingers crossed it works**
Thanks~
squirt11

I have a mac mini which will not wake from sleep mode since installing yosemite.

The cursor moves when using a track pad and magic mouse, but I can't click on anything. Also computer always starts in safe mode now.
Am I the only one having this problem. I have sent the error messages to Apple, but have not seen any updates that might address this issue.
I now have to turn off the sleep function which don't seem right to me. Any advice would be appreciated.

Hi ..
See: "If your machine only boots into Safe Mode (Shift key) any of these may be the cause" > ..Step by Step to fix your Mac | Apple Support Communities

Bridge does not work for wireless clients - connecting to existing network.

Hi - I really hope somebody can help out here, after hours of trial & error, I have finally given up
I need to connect my Airport Extreme Base Station to my existing network. I have a linksys router (192.168.15.1) connected to my modem and this linksys router acts as DHCP server too.
I suppose I have to use "bridge mode" for that to work. But should the linksys be connected to the AEBS using the AEBS's WAN or LAN port?
If I use "bridge mode", then wired computers to the AEBS works fine - getting an IP from the linksys etc. BUT, the wireless clients will have a self-assigned IP and not get through to the internet. It's like the AEBS will not allow wireless clients to "get through" unless AEBS itself is handing out IP addresses.
Page 36 of this manual ( http://manuals.info.apple.com/en/DesigningAirPort_Networks10.5-Windows.pdf ) shows the setup I want. But in the picture, it says "Ethernet WAN port" but the text says: "The Apple wireless device (in this example, a Time Capsule) uses your Ethernet network to communicate with the Internet through the Ethernet LAN port ( <--> )." I don't know which one to use, WAN or LAN - they show WAN but say LAN?
When I set it up as "share an IP address", the AEBS status tells me "double nat" and to change from "shared IP" to "bridge mode". I do that, and everything seems fine - for the wired clients. Now the wireless clients cannot connect, Airport on the MacBook Pro just say "Connection failed" and the MacBook says "Invalid password" (translated from danish), even though I set the Airport Utlity to save the password in keyring, so it should be correct... If I disable wireless encryption, the wireless clients will connect but get a self-assigned IP, and therefor not work (cannot get online)...
It seems the only way I can get wireless to work, is if I set AEBS up as DHCP, but then it won't be on the "same network" as the linksys (192.168.15.1), but rather on 10.0.x.x as I select. If I select 192.168.x.x within AEBS, I'm also getting some error messages, conflict/subnet thing.
Anyway - I really hope somebody knows how to get wireless clients to get an IP address from existing ethernet when connected to the AEBS.
Thanks!!

I've given up and had to go back to running "Double NAT" which also reports as a "problem" within the AEBS, but I just "ignore" it so the light will always be green.
It still ***** though, as "Double NAT" is also a reason for "Back to my Mac" not working properly, but how the ** am I supposed to avoid Double NAT when the wireless will not work in bridged mode?!

Canon Printer mx860 not working since upgrade to Yosemite, it is connected to my Mac via usb. Any suggestions? Thanks. LL

My 2009 Canon MX860 Pixma printer not working since an upgrade to Yosemite on my MAC version 10.10. It is connected by USB. Have had no previous issues with printing, scanning or faxing. When trying to print my Calendar I only get light vertical dotted lines, none horizontal, no words and vague header colors. Checked printer image on the on my MAC which shows the same problem. All of the color and black cartridges are new.
The recent upgrade to the Canon application says it is completed but it is not, image on application upgrade is a circle with an X.
Any suggestions? Could this simply be a compatibility problem? I'd sure like to keep my Canon printer.
Thanks, LL

Can you open System Information (Applications > Utilities) and select Printers in the left sidebar. If the MX is the only printer connected to the Mac then its information will be shown in the right pane. If you have more than one printer, then a list will be shown in the top right pane. Select the MX to see its information in the bottom right pane. Can you copy this information and paste back here for me to check.
Also an FYI - this is the Mavericks forum. The Yosemite forum is here

Canon Pixma MP450 not known

I want to use a Canon Pixma MP450 networked for my macBook.
Since I do not find this type of printer in the default list of printers. I download the installation package from Canon website and install it.
However, even after installing the package, I do not see Canon printer in the list of printer when I am adding a new printer.
Thanks for your help,

If your network consists of the MP450 being shared from a Windows computer, then you will not be able to use the Canon driver. This is because the driver has been written to work on a direct USB connection only, and that is why it doesn't appear in the Canon list of printers.
What you will need to do is look at using a driver that will work across your network and that is the most compatible with the MP450. You have the option of the free drivers from Gutenprint, which you can get from Sourceforge, or buying the PrintFab software. Note that the MP450 is not listed as a supported printer with Gutenprint, so you will have to try a few options to get the best output, whereas it is listed as a supported printer by PrintFab.

NTFS is not working in 64bit-mode

NTFS is not working in 64bit-mode but in 32bit-mode all right !!! ***?!

dont work int volume with XP and ext volume just sample NTFS file server ! I do not understand ! (((

Home Sharing not working between wireless PC's / devices and ethernet wired PC's on the same router.

Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router. I installed a new Verizon FIOS ActionTec MI424WR GigE wireless / ethernet router, replacing the original FIOS router. With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices. With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices. Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
Only the router was changed. No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01. Three PC's are wired and all are running Windows 7. There also is a Windows Home Server connected to the router by ethernet port. It does not run iTunes but does provide WebDAV services to my iOS devices. This works fine. Two PC's are wireless, one running Windows 7 and one running Windows 8. All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point. Two of the wired PC's are connected via a high-speed ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router). All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
Obviously the router seems to be the issue, something between the ethernet and the wireless access point components. I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices. There is no setting that isolates the wireless network. I have done the following:
Read the router user manual and checked all the settings
Rebooted the router and tested.
Turned off the router's firewall and tested.
Home Sharing is turned on all the devices and all use the same Apple ID.
Restarted iTunes and tested.
Verified iTunes is "Allowed" in each PC's firewall.
Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's. I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's. I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
I hope someone may have had a similar problem and has a fix suggestion. I'm stumped! I have a;so contacked ActionTec and awaiting an answer.

Solution from ActionTec is:
Log into your router.
Click the Advanced icon
Cclick Yes
Click on the IGMP Proxy
Select Disable
Click Apply

My iPhone will not work in landscape mode anymore, how do i get to work again

my iPhone will not work in landscape mode anymore, how do i get to work again??

Double click round home button then slide icon on the bottom of screen to so you go all the way to left. There you will see a square icon with a circle arrow . That is the screen rotation control button. Tap on that to lock/unlock screen rotatio

I hooked up new iMac to wireless network and now iPad and iPhone do not work using wireless. I am using a Netgear N300 router. Also my Netgear ethernet/homeplug for wireless TV internet no longer works. Any ideas?

I hooked up new iMac to wireless network and now iPad and iPhone do not work using wireless. They did before hooking up the iMac. I am using a Netgear N300 router. Also my Netgear ethernet/homeplug for wireless TV internet no longer works. Any ideas? I have tried unplugging, restarting, and resetting. No luck! Thanks!

You should probalby contact Netgear

Input Textfields not working in fullscreen mode

Input Textfields not working in fullscreen mode any one help me.

Quotes from Adobe:
"Users cannot enter text in text input fields while in full-screen mode. All keyboard input and key-related ActionScript is disabled while in full-screen mode, with the exception of the keyboard shortcuts that take the viewer out of full-screen mode."
Check with this article to know more: http://www.adobe.com/devnet/flashplayer/articles/full_screen_mode.html

HT1750 space.bar.and.delete.key.not.working.on.wireless.keyborad

space.anddelte
space.and.delete.keys.not.working.on.wireless.keyboard.help!

Before replacing the keyboard do 2-3 SMC resets using the instructions in iMac SMC and PRAM reset

[T400] Cisco VPN client not working over wireless adapter (but works on cabled connection)

I have a very strange problem.
I need to connect to my work via the cisco vpn client (version 5.0.00.0340).
My previous laptop (T43 , windows XP) worked well through both wired / wireless connections. My desktop machine (vista) works via wired connection (it has no wireless connection).
On my new T400, the VPN client works via a wired connection but not via the wireless adapter.
On the wireless apapter, the vpn seems to connect OK, but when I try to access resources via the VPN there is little response.
I get this in the vpn log...
405 08:56:57.073 04/16/09 Sev=Warning/2 IPSEC/0xE3700003
Function CniInjectSend() failed with an error code of 0xa4510009 (IPSecDrvCB:846)
I've tried disabling the firewall (in both the T400 and the router), removed access connections, and disabling tcp v6. I've rebooted everything too.
But, nothing seems to work. I suspect the problem is on the t400 somewhere, because the old laptop used to work OK via wireless.
I've seen some google links on cisco vpn not working via wireless but nothing seems to apply to my exact situation yet.
Anyone else had this problem or know of a fix? Thanks in advance.
Solved!
Go to Solution.

all good now, got it working.
The Deterministic network thing was not installed on the wireless adapter for some reason.
So, I installed the latest wireless driver, reinstalled the vpn and all is good now.

Canon PIXMA MP600R - not working in wireless mode since installing 10.6.1

Similar Messages

Maybe you are looking for