Canon pixma pro 9000II printing - color management and resolution settings

1) is the printer color management automatically turned off when I select the paper in the color management profile drop down? Or do I need to do something else as well?
2) a little bit of a newbie question, but I'm wondering what resolution to select (for presentation prints) - auto or 300 dpi. And again in the print dialogue box (under "quality and media"), whether to use high or standard. Wondering what to match with what, etc.
Thanks.

The answer to the first question appears to be yes. ColorSync is automatically enabled, and Canon Color Matching is automatically disabled.
Some tips on the second question would still be helpful, however. Again, I'm curious about matching Aperture "print resolution" settings (auto, 300, 72, or custom) to the print dialogue "print quality" settings (high, standard, etc.) under the "quality and media."

Similar Messages

Canon Pixma Pro-100 printer ejects 3.8 in of a 4X6 paper and prints only 2.2 in of the image printing from Photoshop CS6, I'm sure I set everything correctly - what could I be missing?

Using Mac Pro running Snow Leopard (10.6.8) & editing & printing from Photoshop CS 6.
Have new Canon Pixma Pro-100 printer and set it up yesterday. First thing printed was a
document from MS Word (a letter) 8.5 X 11 plain paper - this came out OK. Next I fire up
Photoshop and open a 4 X 6 inch image to do a test print. I set it up in the print dialog as
4X6 paper, Canon's Pro Glossy paper profile, rear tray, standard print quality, Photoshop
manages the color. I load the paper in the rear tray close the covers and hit print. Now, when
it starts to print the printer moves about 3.8 inches of paper out of the printer and starts printing
on the remaining 2.2 inches then spits the paper out. It does this in Photoshop (any image it doesn't
matter), and it does it printing from Capture NX. I have been able to get it to print on the paper
correctly using Apple's Preview program but that that's not going to do me any good. I was on
the phone with Canon tech support for about 2 hours and they were completely puzzled suggesting
I would have to use Canon's printing apps instead to print - that doesn't do me any good either.
I want to be able to print from Photoshop. Any one every heard of this or experienced the same
problem? Thanks JamesD!

Hello again. I recognize that a print is good if you like it and bad if you don't, despite what others might say, but I will at least share my experiences. They might help you or others who are following this thread.
My monitor is calibrated with Spyder 3. Gamma 2.2, 6500K, 83 cd/m^2. Contrast at 50%; brightness about 52%. My monitor lets me choose blackness level - it defaults to 50%.
When I print the test image I linked to above, using Lightroom, with no adjustments, my technical output is as follows:
Middle step wedge shows twelve disticnt steps. Whitest step is color of unprinted paper.
It varies from paper to paper, but I can discerne at least the 252 step and on some papers 253 - telling me I have good highlight detail.
On the black side I discerne 8 or 10, nothing lower. (That sounds like what you are reporting).
Artistically I am very happy how my print looks - nice red strawberries, good flesh tones, etc.
One my monitor, the on-screen image is almost identical to the print. I am surprised that you can see the 2 wedge step on screen at a very similar brightness.
I also checked out this B&W test image:
http://www.northlight-images.co.uk/article_pages/bw_printing/bw-test-image-2.html
You are probably aware of this since you are printing with Print Studio Pro, but others may not be.
You can print a series of test images:
find the one that best suits your taste, enter the calibration values in PSP, and save them as a custom setting. Then, each time you want to print recall the setting.
You can do a similar thing in Lightroom using the printer driver and User Templates.
There would be some one-time trial and error to that approach.
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

Canon Pixma Pro-100 prints very dark

I see that this is a recuring problem with the Canon Pixma Pro-100, but as nothing I have found online helps I'm asking and are hoping that someone can solve this problem for me.
Just picked up a Pixma Pro-100 today, and installed it on my 2011 iMac 27" (Yosemite) with downloaded drivers from Canon's website to be sure i have the latest ones. I also checked the printers firmware but that's the latest at 1.100. Wether I'm printing via Lightroom or Photoshop; or via Canon Print Studio Pro, My Image Garden, or via LR / PS directly; with- or without PS as color manager; the prints turns out to be much to dark.
I have to set an exposure of +2/3 in LR to be anywhere close to getting the same result as on the screen. I'm also careful to select the right ICC profiles for the correct paper. My monitor is calibrated with an Spyder4pro and I also re-calibrated it during this process to see if that helped.
Well. Long story short; the prints are to dark. So i borrowed my wife's 2013 MacBook Pro (Yosemite) Spyder4pro, and installed the latest drivers from Canon. Again; on this machine the prints are also to dark with about +2/3 to correct for the printer to do something that looks like the monitor. Both monitors are also set to about 30% brightness.
I also have access to an Epson Stylus Photo R3000 and the prints from this comes out much brighter.
Sadly I see that many others also have the same problem. So; here's the question. How do I fix this? Do i have to return the printer again and get a refund? Because this is clearly not good enough.
Solved!
Go to Solution.

Hello again. I recognize that a print is good if you like it and bad if you don't, despite what others might say, but I will at least share my experiences. They might help you or others who are following this thread.
My monitor is calibrated with Spyder 3. Gamma 2.2, 6500K, 83 cd/m^2. Contrast at 50%; brightness about 52%. My monitor lets me choose blackness level - it defaults to 50%.
When I print the test image I linked to above, using Lightroom, with no adjustments, my technical output is as follows:
Middle step wedge shows twelve disticnt steps. Whitest step is color of unprinted paper.
It varies from paper to paper, but I can discerne at least the 252 step and on some papers 253 - telling me I have good highlight detail.
On the black side I discerne 8 or 10, nothing lower. (That sounds like what you are reporting).
Artistically I am very happy how my print looks - nice red strawberries, good flesh tones, etc.
One my monitor, the on-screen image is almost identical to the print. I am surprised that you can see the 2 wedge step on screen at a very similar brightness.
I also checked out this B&W test image:
http://www.northlight-images.co.uk/article_pages/bw_printing/bw-test-image-2.html
You are probably aware of this since you are printing with Print Studio Pro, but others may not be.
You can print a series of test images:
find the one that best suits your taste, enter the calibration values in PSP, and save them as a custom setting. Then, each time you want to print recall the setting.
You can do a similar thing in Lightroom using the printer driver and User Templates.
There would be some one-time trial and error to that approach.
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

New Canon Pixma Pro-100 printing with streaks on backgrounds

Hello. I just purchased the printer last week. I'm operating on a MacBook Air. I typically use LightRoom and Photoshop.
I'm a professional photographer and recently look a class at ICP and learned how to print there. I was shocked at how beautiful the prints were. This was using an Epson in a classroom.
I did my research and talked to other photographers and decided the Pro-100 would be perfect for me, and so far, it is.
I've had trouble with magenta casts when using LightRoom. Switched to PhotoShop and got better results. But some prints, especially those with a simple, plain background, faint lines appear across the page.
Here's an example. The lines appear top to bottom every 1/4 inch or so:
Solved!
Go to Solution.

Call Canon at 1-866-261-9362, Monday - Friday 10:00 a.m. - 10:00 p.m. ET (excluding holidays).
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

Canon Pixma Pro-10 printing problem

Hello,
I had my printer for little bit over a year, with no problems, until recently.
I am still using the same paper, which is Ilford Gold Mono, but it happened on several other papers as well.
Basically, it seems that carriage grabs the edge of paper and moves it a bit, which creates the effect- see example attached.
I called the Canon service, but since printer is out of 1 year warranty now, they kicked me back to local repair shop.
I am still hoping that I myself can do something to fix this.
Any advice would be appreciated.

Nobody, hah?
Thanks anyway.

Canon Pixma Pro 9000 printer will not print for Lightroom 2.3 or Photoshop CS4

When I hit the print button on either Lightroom or Photoshop CS4 to print using the "front tray", the printer sends a message to lower the tray for the back tray. The Canon tech rep stated that when I hit the Print button on Lightroom or Photoshop there should be "drop down window" which allows me to choose the "front tray". Until I do this, the printer assumes that I am still using the back tray. My question - why doesn't my Lightroom or Photoshop programs display this "drop down window" when I press the "print" button?? Please!! Can anyone help me??

After so many attempts, I don't remember what the display was when I first requested for help. I just trying everything that I
could think of.
I don't think that I downloaded the right Driver the first time. As a last resort, I downloaded the Driver again from Canon and to my surprise, another menu appeared. It was different from the previous ones and rather confusing. The Canon tech had described what I should bd looking for and so I proceeded ahead one drop menu after another and finally the right menu appeared giving me the choice between the automatic back tray and the front tray. After I clicked on the front tray, everything worked fine.
Thanks, Was DYP, for taking time to attempt to help me. It's my opinion that Canon's documentation was not complete and therefore created some confusion.

I just received an OEM copy of Adobe Photoshop Lightroom 5 with my Canon Pixma Pro 100 Printer. What exactly is OEM. Is it a full version? Can I transfer files between different computers?

@

OEM means "Original Equipment Manufacturer", or in your case, Canon (not Adobe) is providing the software. It is identical to what you can buy from Adobe. It is the full version (that's the only version of Lightroom that exists)
Transfer files between different computers ... this is not a function of Lightroom. Lightroom neither helps nor prevents you from transferring files from one computer to another.

Why I Got A Canon Pixma Pro 10

I have had an Epson R3000 printer since it came out in 2011. I was getting puddled photo black ink marks on my Ultra Premium Luster Paper prints. Really liked the print detail, color and contrast. Heck I've used Epson printers since the mid 90's. I was getting exactly what is seen here http://www.dpreview.com/forums/thread/3384029
Must be getting surplus ink on the print head. Tried cleaning it but I didn't get the job done. Would like a removable print head. Never used anything but Epson inks and paper.
Just couldn't take it any more. Started printing today with the Canon Pixma Pro 10. Seems to produce very nice prints IMO. Love the Canon Print Studio Pro plug-in for Photoshop.
Please understand I not complaining. Just decided to move on...
Charlie Wesley
St. Augustine Beach, FL
Canon 5D Mk 111, Canon EOS - 7D Mk II, Canon G1X, Canon Pixma Pro 10 Printer, Sekonic L- 358 incident/ flash meter, Canon EF 24- 105 f/4 IS, Canon EF 70 -200 mm.L f/4, Sigma 180 mm. HSM f/3.5 EX DG APO Macro IF AF, Canon EF 100- 400 mm. F/4.5- 5.6 L IS, Canon EF 500 mm. f/4 L IS, 1.4 TC, 12 & 25 mm. Ext. tubes, Better Beamer, Canon 580 EX II flash

Nobody, hah?
Thanks anyway.

Canon Pixma pro 100 Ink how to identify the black cartridges when label was accidently removed

I just started putting a new Canon Pixma Pro 100 printer together- I was not thinking and removed two of the grey (light), and grey cartridges labels. Now I do not know which to put in the slots, I cannot see any gradient by holding them up to the light, and the actual cartridge is not marked. I am soooo dumb, any suggestions.

You got a 50/50 chance. Go for it!
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 8.7, Lightroom 5.7

Canon pixma pro 100

Hi guys,
I've just received my new canon pixma pro 100 printer & I'm having problems setting up. When powered up the printer instantly made a grinding noise. Switched it off a few times but the print head holder failed to slide along the rails. All stoppers & tapes have been removed so nothing to obstruct the set up process.
Can anyone help or had similar issues?
Thanks in advance.

You are possitive there is no packing or tape left inside? 100% sure?
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 9, Lightroom 6

Managing Color with LR and the Canon Pixma Pro 9000 10.1.2.0 printer driver

I would like help understanding how to manage color in LIghtroom with the Canon Pro 9000 10.1.2.0 printer driver. When I ask LR to manage color in the Printing Module Color Management Profile, it warns me to turn off the printer managing color. But I cannot find where to do this in the driver.
The Color Options menu in the driver gives an additional choice for "Color Mode", but there are no choices here except "Standard", "Linear" or "Tone". The only Canon documentation I can find shows a choice to turn off printer management here, but this driver doesn't give me that choice.
If I look in the driver's "Color Matching", I see only two choices: ColorSync or Vendor Matching. ColorSync brings up Canon profiles like "Pro9000 Fine Art Photo Rag", but selecting one of these gives a warning of unexpected results. This pushes me back to Vendor Matching. But is this turning off the printer driver and leaving it to Lightroom?
Right now, I am getting the best results from choosing "Managed by Printer" in LR's Color Management Profile, and setting "Color Matching" in the Canon driver to "Vendor Matching". If I instead choose one of the Canon profiles in LR's Color Management Profile (and it tells me to turn off the printer managing, which I cannot do), then my prints have a slightly bluer color cast.
Is there a way to turn off the printer managing color in this driver and turn this over to LR, or am I getting the best results possible with the printer managing color anyway?
I am using a 2.4 GHz Intel iMac with OS 10.5.4, 2 gigs SDRAM, standard ATI Radeon HD 2600 Pro video card. I downloaded the Canon printer driver from their website, so I assume this is the latest. there is another driver available at their website, but for a lower bit depth. Should I abandon the 10.1.2.0 for this other one? I work with Nikon D300 NEFs, and I assumed the higher bit depth printer driver will work better with these images.
Any help will be greatly appreciated!

Dear DYP: Unfortunately, those choices are not available in the 10.1.2.0 Canon Printer driver. There are only 2 radio buttons, ColorSync and Vendor Matching. ColorSync then provides a drop-down menu, with no choice for turning off the printer driver.
But I think I found the answer. I found a deeply buried FAQ on the Canon site (no direct URL; sorry!) Here it says:
"Issue: How do I disable the printer driver color correction when using the CUPS driver in Mac OS X 10.5.x?
Solution: Change color management options for printing (Mac OS X 10.5.x)
Change color management options for printing
Open the document you wish to print.
Click 'File' and then click 'Print.'
Note: If the Print window contains only two pop-up menus, click the triangle beside the Printer pop-up menu for expanded options.
Select 'Color Matching' from the Print Options pop-up menu.
Select 'ColorSync' if you want the application you are using, and not the printer driver, to control the color management of the printed output.
Note: If you are using Adobe Photoshop CS2 or CS3 and have selected 'Let Photoshop Determine Colors', the 'Color Matching' from the Print Options pop-up menu is automatically set to 'ColorSync.'
Select 'Vendor Matching' if you want the printer driver to control the color management of the printed output."
I tried it, and chose "Automatic" as a choice in ColorSync. The choices under "Color Options" are then greyed out, implying that the Canon driver is now turned off.
The prints came out great, with no color cast, and a little brighter than the printer managed prints.
So, Vendor Managed means printer manages, ColorSync means LR manages.
Thanks, everyone, for keeping me going on tracking this down!

Canon pixma pro 9500 having problems with my print out. colors are glazed and missing colors

canon pixma pro 9500 having problems with my print out. colors are glazed and missing colors
i have prfiled the mac and printer wiht colormunki and uplodated the profile sucessfully
i set the printer to correct icc profile
print out comes out same with glazed colors and missing tones/colors
however when i use the same printer on windows and with light room, following same icc profile, colormunki calibrated profile, the print our are excellent.
i have also tried using printer manage profile using the Mac and Aperture and get same poor prints
can you please assist and thanks

I've a Pro9000 and also use Colormunki successfully.
When I use Colormunki, I calibrate both of my monitors and the printer/paper combination. Colormunki saves the generated profiles to the correct places -- I don't load or change any profiles after that as that would mess-up what the Colormunki had just done for me, and this would likely mess-up the prints.
Though I double-check the settings in the print dialogue, the choice for the printer handling things is already grayed-out. Colorsync handles it all just fine.

How to print from Lightroom 5 to Canon Pixma pro-100?

Using Lightrooms printmodule with this printer is a big problem for me. Using Cannon Print studio Works, but then you
loose a lot of great functionallity in LR print module.
It seems that when I make a preset or set up printer with correct ICC profile the canon printer driver automatically resets to its own default.
It looks like a print driver in the background resets everything i do. Very confusing and Canon support points to adobe.
My setup:
Macpro with OSX 10.9.2 (latest version)
Lightroom 5.3 (creative cloud member, always latest version)
Canon Pixma pro-100 (bought new april 2014)
I have looked several places on internett and it looks that there are a lot people having similar problems.
I would appriciate any help to find an easy setup/soltion !
Thanks in advance
Nicolaas

I have the Pixma Pro-100. But I'm using Windows 7, so I'm afraid I can't be a lot of help to you. I tried to help someone in another forum the other day and showed some screenshots, but he said he didn't have anything like that on the Mac.
If you're going to use ICC profiles, you have to turn off color management either in the printer or in the printer driver. It doesn't matter which one, just make sure that it gets turned off. Then what I do is I use soft proofing with the appropriate paper profile to prepare a soft proof copy for printing. After I have set my printer settings the way I want them and have everything just right in Lightroom, I save the preset for printing. And it seems to keep what I have set. If you can show me some screenshots of your printer driver, perhaps I can be of assistance.
Regardless of whether I allow Lightroom to manage the color or allow the printer to manage it, I am getting really nice prints. So I'm sure there's something that you are probably just overlooking.

Printing Issuse From Lightroom 4 To Canon Pixma Pro 9000 MK II

I have been trying to print from Lightroom 4 to a Canon Pixma Pro 9000 MK II. Whenever I try to print via the front try (for canvas) I get an error message (code 1281) and I cannot print. I have tried a few different papers as well as canvas and all of them give the same error code.
I have also tried printing from Elements 9 with the same problem.
I can print via the front try using Canon's own software, Easy Print Pro, but I cannot soft proof the image first and I cannot the the correct size of image either.
Does anyone have any idea how I can get round this problem?
I have spoken to Canon and they have passed the buck saying that as I can print using thier software it is an Adobe issue.
Printer: Canon Pixma Pro 9000 MKII
Software: Adobe Lightroom 4
Operating System: Lion OSX

The final answer was as per Rikk Flohr's instructions,
Lightroom>Print Module
Print Settings button Bottom Left-hand Panel
Set the Center Pull-down to Quality and Media
Paper Source: Front Tray
I was having difficulty finding these previously, thanks Rikk.

Print Color Management Problem w. Photoshop Elements and Tiger/Leopard

Has anyone tried printing with ICC profiles through Photoshop Elements 6 for Mac? Apparently, it does not work on Tiger nor Leopard? My prints look very dark and over-saturated.
The Datacolor folks, who make the Spyder3 calibrators I'm using, say my prints look like they are being "double color managed," possibly once by PSE and once by the printer driver (even though it's turned off).
Over at the Adobe Forums some say it's a problem with Leopard. I'm not so sure, because I found that printing color management works fine on a Mac with Photoshop Elements 4.01 and Tiger. Any comments? Thanks.

Aha! Got it. Adobe has confirmed that the problem is on their end. PSE 6 is double color managing the images. Here's what one user got in reply from Adobe on the subject. There are two separate answers:
Thank you for contacting Adobe Technical Support.
After consulting with my colleagues about the issue you raised, I can let you know the following:
The issue is both on our as well as the driver software side and the workaround we have given is the best available at this time. This issue is affecting all printers, not just Epson or Canon.
The soft proofing effect that you are seeing in the print preview is indeed an attempt at soft proofing. However since Photoshop Elements managed prints are incorrectly double colour managed it is not as useful as it was initially designed.
As to the exact details of why this occurred, we have no official information.
We believe that this will resolve the issues you are experiencing, however, should the reply not help solve the problem, please contact us again, quoting the case number given above, and we will re-open the case.
Answer # 2
We have had word back from our engineers regarding your issue.
The Photoshop Elements team are aware of the problem and are working with Apple and the printer manufacturers to get this to work correctly. In the meantime, the only workaround is to switch off colour management in Photoshop Elements and let the printer handle the colour management.
Unfortunately we can not make an estimation as to when a fix will be provided. We will close the case for the time being as there really is nothing more we can do about this issue besides offering the suggested workaround. Closing this case does not mean that the research will stop however and the engineers are working on a solution to this.
As the tech noted, let the printer handle the color instead. Tell PSE not to manage color so it is the step sending the data unaltered. When the print dialogue comes up, under the Color Correction heading, change the pull down menu to "ColorSync". In the menu below that, choose the correct profile for the paper you're using. If the Brightness menu is still active, look for any choice that allows you to turn it off. If none exists, leave it on Normal. If the options below that for Color Balance and Intensity are not grayed out, make sure they are at the center positions (no effect).
These steps are the same as before, except you're doing them in reverse. Photoshop is doing nothing and the print driver is handling the ColorSync chores rather than the other way around.

Canon pixma pro 9000II printing - color management and resolution settings

Similar Messages

Maybe you are looking for