Canon printer paused

Since upgrading to Mountain Lion, every time I try to print to the ethernet networked Canon MP 620 printer, nothing happens.
I see the printer icon in the dock flash, the message says it is printing but nothing happens. I pause the printer then resume a few seconds later and the document usually prints. On occassion, a window opens and I need to enter my password.
Printer is hard wired ( ethernet ) to an Apple Extreme Base Station.
I downloaded the most recent Canon printer drivers. As a non-techie, do I need to remove the old drivers, uninstall and reinstall the printer with the new drivers ?
Any suggestions are appreciated.
Dan

The new driver should overwrite the old. So no removal of files is required at this stage.
What I do recommend you try is removing the current printer from Print & Scan and then adding the network printer again. The see if that will print.

Similar Messages

Can't print on Canon printer since 10.8.2

We have a Canon i-SENSYS LBP 5050n printer. When I upgraded my MB Pro to Mountain Lion, I could not print anymore, until we found a printer driver at Canon Australia's web site, version 3.55. Updating to 10.8.2 again leaves me without the chance to print: the document stays in the printer queue forever: for a while it looks like it migh porint, then it goes into pause mode. Resuming does not help either.
Where can I find a printer driver that allows me to print again, or what else can I do?
Thanks for your help,
Wladimir

Thanks a lot, Pahu, for your help. I just read the other postings, which seem to cover exactl the same problem as I have. I did check for similar threads before posting my question, but obviously I have missed that oen; sorry.
The CAPT backgrounder is running, then entry in System Information > Printers > Canon LBP 5050n > URI is cnbma://localhost:59687 and still it is not working.
Here are the contents of my ccpd.conf file:
# Canon Printer Daemon for CUPS Configuration Data
<Path>
# CUPS configuration files Path
# Default /
CUPS_ConfigPath /
# LOG Directory Path
#LogDirectoryPath /var/log/CCPD/
</Path>
# Printer entries
# Mapping each "Printer-Name" to "Printer Device Port".
# The "Printer-Name" has to be identical to the CUPS printer queue name.
# For example, if you prepare a printer named "XXXX" as a CUPS printer
# queue name, and the printer is connected to the USB port "/dev/usb/lp0",
# you can use the following three lines example just by removing the
# comment symbol "#" of each line.
#<Printer XXXX>
#DevicePath /dev/usb/lp0
#</Printer>
<Ports>
# socket port
UI_Port 59787
# backend data port
PDATA_Port 59687
</Ports>
Some additiona information: the poster of the question in the other thread you informed me about, 6andalf, write that ever since updating to Mountain Lion he cannot print. The same happened to me, until I found CAPT 355 on Canon Australia's web site, as mentioned. When I updated to 10.8.1 I could still print, until I installed 10.8.2.

How can I set up a Canon printer on iMac with cd? (iMac has no cd/dvd drive?)

Purchased the latest iMac with no dvd drive; also purchased a Canon printer with dvd set-up; how can I install printer on iMac?

Macs do not usually need to download anything from the CDs that come w/printers. Read the user manual that came w/the printer and/or contact Canon Support.
Or purchase an external burner. Do not purchase Apple's usb burner. 3rd party burners are 110% better.

I'm trying to share a new Canon printer wirelessly between my HP laptop and my iMac. I've successfully printed from both computers, but, I get errors trying to print on one after I've printed on the other. Any ideas on how to get them to both to print?

I installed a new Canon printer several months ago that I was told by the salesman could be shared between my iMAC and HP laptop. I have successfully used the printer wirelessly from both computers, however, it gets hung up switching between the two and I'm not sure what to do to get it to be consistent. Any ideas?

You didn't state how it's connected to each computer, if it's connected through your router then it should work. If it doesn't then you need to contact Canon and ask for assistance.

Network printing Printer Pauses /usr/libexec/cups/backend/lpd failed

Morning,
I wonder if anyone has encountered the following problem?
NETWORK SET UP
We have a network of 8 macs & a Fuji Xerox c2255 printer all connected to a gigabit switch.
The Fuji Xerox has an fixed ip address 192.168.1.122 All devices have fixed ip address.
PROBLEM
Only one mac (Mac Pro) can print direct to the Fuji Xerox Printer. This Mac Pro is on 10.5.8. and it is sharing its printer connection with the rest of the studio. Oddily enough, the Appletalk function is turned on. When the appletalk function is turned off on the ethernet port, it can not longer directly print nor share the Fuji Xerox with the rest of the network
The remainder of the Macs are all on 10.6.4 or 10.6.3. When the printer is first installed on the an iMac client, it can print from text files, offices docs, from safari or firefox with out any problem. But when it attempts to print a pdf file (preview) or Indesign files then it pauses the printer. Within the printer queue, if attempt to restart the printer, the printer pauses. It remains in this state indefinitely. When looking at the CUPS logs via the console, the error is printer-state-message="/usr/libexec/cups/backend/lpd failed". This is the message displayed on all the clients that attempt to print directly (via LPD) to the Fuji Xerox. Once this error message is logged, the iMac can no longer print out text files nor word documents.
The following console log is typically of what all the 10.6.x clients are reporting,
D [15/Jul/2010:18:38:07 +1000] [Job 4] STATE: +connecting-to-device
D [15/Jul/2010:18:38:07 +1000] [Job 4] Looking up "192.168.1.122"...
D [15/Jul/2010:18:38:07 +1000] [Job 4] Connecting to 192.168.1.122:515 for printer
D [15/Jul/2010:18:38:07 +1000] [Job 4] Connecting to printer...
D [15/Jul/2010:18:38:07 +1000] [Job 4] STATE: -connecting-to-device
D [15/Jul/2010:18:38:07 +1000] [Job 4] Connected to printer...
D [15/Jul/2010:18:38:07 +1000] [Job 4] Connected to 192.168.1.122:515 (IPv4) (local port 1008)...
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.1 = 7500
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.2 = 1170
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.3 = 400
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.4 = 585
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.5 = 25000
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.6 = 18400
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.7 = 19600
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.8 = 19200
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.9 = 19600
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.10 = 200000
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.11 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.12 = 200000
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.13 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.14 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.15 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.16 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.17 = 200000
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.18 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.19 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.20 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.21 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] prtMarkerSuppliesLevel.1.22 = -3
D [15/Jul/2010:18:38:07 +1000] [Job 4] ATTR: marker-levels=50,75,25,50,100,46,49,48,49,100,-1,100,-1,-1,-1,-1,100,-1,-1,-1,- 1,-1
D [15/Jul/2010:18:38:07 +1000] [Job 4] lpd_command 02
D [15/Jul/2010:18:38:07 +1000] [Job 4] Sending command string (2 bytes)...
D [15/Jul/2010:18:38:07 +1000] [Job 4] Reading command status...
D [15/Jul/2010:18:38:07 +1000] [Job 4] lpd_command returning 1
D [15/Jul/2010:18:38:07 +1000] [Job 4] Backend returned status 1 (failed)
D [15/Jul/2010:18:38:07 +1000] [Job 4] Printer stopped due to backend errors; please consult the error_log file for details.
D [15/Jul/2010:18:38:07 +1000] [Job 4] End of messages
D [15/Jul/2010:18:38:07 +1000] [Job 4] printer-state=5(stopped)
D [15/Jul/2010:18:38:07 +1000] [Job 4] printer-state-message="/usr/libexec/cups/backend/lpd failed"
D [15/Jul/2010:18:38:07 +1000] [Job 4] printer-state-reasons=media-low-report,toner-low-report,paused
APPROACHED USED TO DATE
1. I have reset the Printer subsystem for all clients
2. I have reinstalled the latest PS drivers for this model of Fuji Xerox c2255. I have been on the phone with Fuji Xerox Technical support, FX DocuPrint C2255 v3017.104PS , and confirmed that this is the latest (and only) availible drivers for 10.5-10.6
3. I have had the Studio manger arrange to have the Fuji Xerox printer fully serviced and had the firmware updated to latest version.
4. Via Fuji Xerox Technical support, they advise I use the following settings for LDP printing for FX c2255,
Latest driver for 10.6 : 3017.104.ps
Setting to check :
Queue name : PS
Enable EtherTalk
LPD port : from auto to PS
Software version :
Controller plus PS role 1.100.21
5. I have (manually) deleted the all the FujiXerox drivers from /Library/Printers/ then repair permissions, then reinstalled the latest version of the Fuji Xerox driver from 10.6
WEIRDNESS
1. With the 10.6.x client, when the drivers are first installed, if I create a simply indesign file, I can print directly to the Fuji Xerox. If I then attempt to print out a previously created indesign document, it will pause the printer and the console (CUPS error_log) will display the above result. If I switch my printer to the Mac Pro 10.5.8 sharing the printer, the same document can print out via the hosted Fuji Xerox.
2. The Mac Pro 10.5.8 can print all documents directly to the Fuji Xerox regardless of the format of the document. It is also able to share the printer with the dept. This is the sole means of the dept being able to print out artwork.
3. Prior to the firmware upgrade I have tried an iMac printing/hosting the Fuji Xerox via direct USB cable. The same behaviour as above were experienced.
4. This model of Fuji Xerox only supports LDP or direct USB connection.
5. I have tried using the Bonjour address to configure the printer but the results are no better nor no worse. At one stage, all the iMacs were able to print sucessfully for a day but then 'stopped working' (as reported by the studio manager). They then switch back to the Mac Pro hosting the printer to continue working.
6. I discovered that if the drivers are installed and then a Permission repair carried out (via Disk Utility), it would change all the driver permissions for the files in the /Library/Printers/FujiXerox. When attempting to print (with the revised permissions), the 'print' button would not 'work'; the print dialog would present until Cancel was selected. It was almost like changing the permissions has lock out the functionality of being able to print. Manually moving the FujiXerox to Trash and reinstalling the drivers reverted the printer back to the above behaviour.
7. I discovered that when installing the printer, using LPD, it is better to allow the default settings. If I stuplated that the Fuji Xerox is a two bin set up, rather then a single bin set up, I can not print out from any application. If, I left settings as default, my assumption is that the apps can mange the printer features.
I've been working on this for a while now and this is driving me crazy. I would appreciate any suggestions. Has anyone come across this issue before ? Any ideas ?
Thank you,
Fred

Hi Pahu,
Thanks for your reply. I noticed that you have replied to a number of other postings as well - you're a good sort !! Your knowledge and contribution to this forum is much appreciated and very welcome.
Yes, this is a curly problem. I've actually been trying to resolve it for several months. Interesting the c2255 is not stated as being supported under Apple's Fuji drivers release for SN. The driver has to be downloaded directly from Fuji Xerox. The following is from the c2255 Config page,
Communication Settings
Ethernet Rated Speed
Connection Type Auto
MAC Address "08:00:37.8C:76.0C"
TCP/IP
IP Mode IPv4 Mode
IPv4
IP Address Resolution STATIC
IP Address "192.168.1.122"
Subnet Mask "255.255.255.0"
Gateway Address "192.168.1.1"
IP Filter Disabled
Status Ready
WINS
DHCP Address Resolution Disabled
Primary WINS Server Address “”
Secondary WINS Server Address “”
DNS
Domain Name “”
IPv4
DHCP Address Resolution Disabled
Preferred DNS Server “”
Alternate DNS Server 1 “”
Alternate DNS Server 2 “”
Dynamic DNS Registration Disabled
SSL / TLS
HTTP - SSL 1 TLS Communication Disabled
LDAP - SSL ' TLS Communication Disabled
IPSec
IPSec Communication Disabled
IEEE 802. lx
]EEE802.lx Disabled
SNMP
Port Status Enabled
Transport Protocol UDP
SNMP Version v1 / v2c
Internet Services
Port Status Enabled
Port Number 80
Maximum Number of Sessions 5
Connection Time-Out 30 seconds
SOAP Enabled
Port Status Port Number 80
Maximum Number of Sessions 3
Connection Time-Out 30 seconds
USB-1 (2.0)
Port Status Enabled
Print Mode ‘Postscript 3’
PJL Enabled
Adobe Communication Protocol Standard
Auto Eject Time 30 seconds
USB-2 (2.0) Port Status Enabled
Print Mode Auto
PJL Enabled
Adobe Communication Protocol Standard
Auto Eject Time 30 seconds
NetWare Port Status Disabled
LPD
Port Status Enabled
Print Mode ‘Postscript 3’
PJL Enabled
TBCP Filter Disabled
Port Number 515
Maximum Number of Sessions 5
Connection Time-Out 16 Seconds
SMB
Port Status Enabled
Prim Mode Auto
PJL Enabled
Transport Protocol TCP/IP. NetBEUI
TBCP Filler Disabled
Workgroup "WORKGROUP"
Host Name "AP-8C760C"
Auto Master Mode Off
Password Encryption On
Maximum Number of Sessions 5
Unicode Support Disabled
Administrator Name "ADMIN"
EtherTalk
Port Status Enabled
Print Mode PostScript 3'
PJL Enabled
Printer Name "DocuPrint C2255”
Zone Name “*”
IPP
Port Slatus Disabled
Port 9100
Port Slatus Enabled
Print Mode Auto
PJL Enabled
Pon Number 9100
TBCP Filter Disabled
End of Job Timeout 60 Seconds
WSD
Port Number 80
Data Receive Time-Out 30 Seconds
Maximum TTL 1
Maximum Number of Subscribers 50
Notification Delivery Time-Out 8 Seconds
Print Service
Port Status Enabled
Print Mode Auto
PJL Enabled
TBCP Filter Disabled
UPnP
Discovery
Port Status Enabled
Port Number 80
SSDP
Valid Advertising Period 180 Minutes
Maximum TTL 1
Bonjour
Port Status Enabled
Printer Name "DocuPrint C2255
What is interesting is that this problem occurs with all the 10.6.x macs. There is a Mac Pro that has been upgrade to 10.6; an iMac that has had a complete rebuild with 10.6; two iMacs that have been upgraded from 10.5.x and two new iMacs that came preinstalled with 10.6.2. None of these Macs can direct connect to the Fuji Xerox c2255. Only the 10.5.8 Mac can direct connect to the FX c2255 and can host (or share) the FX c2255 printer to the rest of the network.
One of the bizarra aspects is that the all the Macs can print text files, offices docs, web pages, etc, etc directly to the Fuji Xerox c2255 without any problem. BUT try to print a pdf file from preview or from Indesign and it resorts back to the status described earlier. Oddily enough, if I create a simple pdf in Indesign (circle, squares, a paragraph of text), I can print out the file using Indesign, directly to the printer. If I import one of the previously created documents, the printer reverts to the status described earlier. HOWEVER, if I take the same document and print via the Mac Pro 10.5.8 hosting/sharing the printer, the document will print without any problem. What the... ??!?!?!
I thought it might be a firmware problem but following the onsite service of the printer, I think I can rule that out.
Can you see anything that I might be missing ???
Thank you,
Fred

How can I set Firefox to print to PDF, the only otions I have are (1) My Canon printer, (2) Fax or (3) Microsoft XPS document writer. There is no option for PDF

A couple of weeks ago, from the file menu, in my print options was to print a web page to PDF, that facility is no longer there. does anyone know how can I set Firefox to print to PDF.
The only options I have are (1) My Canon printer, (2) Fax or (3) Microsoft XPS document writer. There is no option for PDF

Firefox generally displays the printers in Windows' Printers folder (Start orb > Devices and Printers). If it is missing one of the printers listed there, could you indicate which one it is, for example, Adobe Distiller, PrimoPDF, CutePDF Writer, etc.?
If you previously had an add-on which added print-to-PDF functionality just to Firefox, perhaps it got disabled. You could check here:
orange Firefox button ''or'' classic Tools menu > Add-ons > Extensions
Also, are you really running Firefox 8.0.1? That version from last November is no longer secure and has been superseded by Firefox 11. If you browse the web widely, you should update for your security.

Sharing the Canon printer on my iMac with a Windows Vista PC

Sorry guys,
You must have been asked this many times before. I just cannot share my Canon iP4500 with a friend's PC running Vista. I have installed Bonjour on his PC, but haven't got a clue how to access it on Vista. The PC and the iMac both connect to a wireless router, but trying to make them talk to each other is proving very difficult!
If someone here has the knowledge and patience, what I would like is a step-by-step guide. Do I need to install the Canon printer driver onto the PC? The assistance on the Apple web site is very sparse in this area, to say the least!
Thank you in advance.
Graham

Hi Graham,
In the Sharing pref pane on the Mac, are Windows sharing and Printer Sharing both enabled?
Not positive on the PC end, but I think Printer Sharing should not be enabled.
Bonjour on the PC is accessed by right clicking on a Connection, at least in XP.
See if this is some small help...
http://www.macosxhints.com/article.php?story=20060414230039896

TS3938 Can no longer scan with my MP800 Canon printer

I've seen lots of posts on this, and it is extremely frustrating that I'm starting to think it's just assumed that the owners of MP800 Canon printer/scanners will just toss out a perfectly good, little-used piece of hardware and buy something new. I've tried going to the HP site, loading the new drivers, etc. I've also tried changing from MP Navigator to Image Capture, but nothing happens when I open the Scanner, except for an empty screen that turns completely white when I click on Show Details.
I am REALLY disappointed in Apple OS update. In the PC world (which I bought a mac to get away from) I would just uninstall the entire printer, then re-install it and count on the correct drivers etc. to be loaded. I've tried to find a way to do this on the forums, but no luck. Is there any way to un-install the printer/scanner completely? And then re-install it to pick up the new drivers/software or whatever, that would work?

Uninstalling and reinstalling the drivers should resolve this issue. Please perform the following to remove the currently installed drivers: (If any items are not listed, move on to the next step.)
1. Open Finder
2. Open the 'Library' folder.
3. Open the 'Printers' folder.
4. Open the 'Canon' folder.
5. Send the 'BJ Printer' folder to the trash.
6. Return to the 'Library' folder.
7. Open the 'Receipts' folder.
8. Locate any items related to your printer and send them to the trash.
Leave the 'Canon Printer Drivers.pkg' file in the folder if it happens to be listed.
9. Return to the 'Library' folder.
10. Open 'Image Capture'.
11. Open the 'Twain Data Sources' folder.
12. Send any Canon files related to your printer to the trash.
13. Open the Applications folder.
14. Open the Canon Utilities folder.
15. Send the MP Navigator to the trash.
16. Restart your computer.
To get your MP800 Canon printer operating , please follow these steps:
Download the following drivers:
mcpd-mac-mp800-10_51_2-ea11.dmg
msd_-mac-mp800-12_13_3-ej7.dmg
mpnosx207ej7.dmg
Once the downloads are completed, open each installer package to begin setup.
Once this process is completed, try scanning and printing with your MP800 Canon printer.

"Can't install the software because it is not currently available from the software update server." Running Mavericks, Canon printer. What do I do?

We have a canon printer and it connects fine to my boyfriend's HP. I can't get it to connect to my macbook though--when I plug it in with USB it asks me if I want to install the software, has me agree ot the user terms and conditions, and then I get the error message. I've installed all updates, tried turning my computer on and off. Where do I go from here?

Did you install the Software Update beforehand? I believe you need this so that your Mac's database will update on your newly connected devices. Try the solutions here. I just did what it says there and then restart my computer and my router after all the process and it works for me. Goodluck!
http://www.techyv.com/questions/software-not-available-software-update-server

I am trying to scan a legal size document from my Canon printer onto my MacBookPro. It scans the document as a letter size.

I am having trouble scanning a legal size document from my Canon printer onto my MacBookPro. I have set the printer paper size option to legal size on my printer. The scanned document comes through as a letter size document after scanning. I do not see an option in iPhoto to change the paper size.
Can anyone advise?
Thanks.

Lazy Oak wrote:
I am having trouble scanning a legal size document from my Canon printer onto my MacBookPro. I have set the printer paper size option to legal size on my printer.
Experience has taught me that it pays to be very precise and specific when dealing with computers. Precisely and specifically, what you describe is impossible. It is impossible to scan a document (of any size) with a printer.
I surmise that you are using an all-in-one, ie, an apparatus which combines a printer, a scanner, and sometimes a fax machine, in the same device. That takes us to the next step -- the page size set for printing is used for printing -- it has nothing to do with scanning. It may be possible that Canon provides software which synchronises page sizes used for printing and for scanning, but we don't know what applications and drivers you are using…

Printing Problem on Canon Printer

Hi Gurus,
Greetings and Thanks in advance!
I have problem in Invoice printing on new Canon LBP 2900 B printer. Whenever I print on this printer the one character from right side does not print. Whereas if the same printing we are doing on HP Laserjet printer it comes perfectly.
I tried to create a new output device through SPAD in which I have used following:
Device Type: SWIN Windows printing via SAPlpd (since i didnt find Canon printer in the list so i used windows standard)
Device Class: Standard Printer
Host Spool Access Method: G:Front End Printing with control Tech.
Host Printer: _Default
But it was giving the same problem. Please suggest the solution.
Regards
Rajesh
Edited by: Rajesh Gupta on Jul 7, 2010 3:59 PM

Check
1135052 - Printer-Vendor-Programm - Wizard-Note:: CANON
Markus

Is there any way to print to a canon printer from macbook?

Is there any way to print to a canon printer from macbook?

Yes. What happens when you try?

Adobe Photoshop CS6 and Canon printer problem!!

Use Photoshop CS6 to edit and print (try to print) to a new Canon Pixma Pro-100 printer. Photoshop is up to date and the Mac runs OS 10.8.5 - Canon printer driver is current at ver. 11.7.1.
When I print from Photoshop to the Pro-100 (let's say a 4X6 landscape snapshot to 4X6 borderless paper) the printer starts up and moves the paper out about 4 inches and then prints the
first two inches of the image, stops and ejects the paper!. I've tried different versions of printer the printer driver and made sure every things is up to date. However, I can print from MS Word,
Nikon Capture NX2, or Canon's own Print Studio Pro and it works fine. Canon is no help because if it works OK with their Print Studio Pro then it's not their issue - I tend to agree with them.
The same thing happens print from Photoshop to 5X7 or 8X10 paper - it gets ejected so far and then only prints part of the image. I've searched the Internet and posted in Forums but can't find
where any one would have the same problem. What I'm hoping for here is someone at from Adobe who's knows Photoshop tech stuff will post here with suggestion because there is no more
phone support for Photoshop CS6. I'd like to really keep this printer and get Photoshop to work with it but if I can't I'm going to offer it up free to a good home! JM Davis

Thanks for your answer, indeed this fixed the problem. Quite stupid I did not see this myself

How do I set up a Canon printer that is asking for a WPS button?

I am trying to set up a Canon printer and cannot figure out how to do it with Airport Extreme as they are asking for a WPS button to be pushed....Please Help!

What operating system is being used on the computer that is configuring the printer and AirPort Extreme?
Apple has not supported the WPS type of setup for some time, so it may likely be necessary to use the manual setup option to configure the printer. Check the printer documentation for that procedure.
In this type of setup, the printer connects just like a laptop. You search for the wireless network, select it and enter the password to connect.

Canon Printer mx860 not working since upgrade to Yosemite, it is connected to my Mac via usb. Any suggestions? Thanks. LL

My 2009 Canon MX860 Pixma printer not working since an upgrade to Yosemite on my MAC version 10.10. It is connected by USB. Have had no previous issues with printing, scanning or faxing. When trying to print my Calendar I only get light vertical dotted lines, none horizontal, no words and vague header colors. Checked printer image on the on my MAC which shows the same problem. All of the color and black cartridges are new.
The recent upgrade to the Canon application says it is completed but it is not, image on application upgrade is a circle with an X.
Any suggestions? Could this simply be a compatibility problem? I'd sure like to keep my Canon printer.
Thanks, LL

Can you open System Information (Applications > Utilities) and select Printers in the left sidebar. If the MX is the only printer connected to the Mac then its information will be shown in the right pane. If you have more than one printer, then a list will be shown in the top right pane. Select the MX to see its information in the bottom right pane. Can you copy this information and paste back here for me to check.
Also an FYI - this is the Mavericks forum. The Yosemite forum is here

Canon printer paused

Similar Messages

Maybe you are looking for