Canon scanner not communicating with mac min using OS 10.5.8

I am using a mac mini with OS 10.5.8. I am trying to scan in papers with a Canon Canoscan N1240U. This is the message I am receiving.
     Cannot communicate with canner.
     Cable may be disconnected.
     Check status.
     Scanner driver will be closed.
I have used this scanner before with this mac mini. Any suggestions why this is happening and to correct the issue.

I think you should, if you can, try the scanner on a different computer to rule out a problem with the scanner or it's usb cable. Then, if you have the software install disk for the scanner run it. Or download and install a new driver or software. Use the finder to find and delete any files for the scanner and then reinstall them. set the scanner up in systempreferences as if it's a newly installed item.

Similar Messages

The best audio interface with Mac Mini using new & existing equipment?

Hi,
I got my existing set-up back in 2003. I'm now about to update it.
I've talked to Apple Technical Support re which computer is best for me.
Some important questions remain in terms of the audio interface or sound bridge I should use.
I've detailed below my existing set-up, my existing configuration, my desired set-up (as recommended by Apple expert) and questions I have.
Existing set-up:
Hardware...
1. ViewSonic HDMI 1080p Full HD LED monitor
2. PowerMac G4 (PowerPC processor) computer
3. PCI-424 soundcard within computer (works in conjunction with MOTU 2408 mk3 unit)
4. MOTU 2408 mk3
5. Quested monitors
6. Focusrite Session Pack ff ISA220 compressor
7. MOTU micro lite (midi-usb interface)
8. Keyboard (yet to choose - I'll explain later)
9. ADK Tube Condenser Commemorative Edition microphone
10. ADK Tube Condenser Commemorative Edition microphone power box (supplies both power and phantom power)
Software...
11. Tiger 10.4.11 operating system
12. Logic Studio 8 music program
Desired set-up:
1. ViewSonic HDMI 1080p Full HD LED monitor
2. Mac Mini full spec = £999.00
3. _______________________________________
4. _______________________________________
5. Quested monitors
6. _______________________________________
7. _______________________________________
8. _______________________________________
9. ADK Tube Condenser Commemorative Edition microphone
10. ADK Tube Condenser Commemorative Edition microphone power box (supplies both power and phantom power)
Software...
11. Top-end operating system = Comes with Mac Mini
12. Logic Pro X music program = £139.99
Existing configuration:
ViewSonic HDMI 1080p Full HD LED monitor goes into PowerMac G4 (PowerPC processor) computer
PCI-424 soundcard within computer (works in conjunction with MOTU 2408 mk3 unit)
MOTU 2408 mk3 used as my audio interface for sound in and sound out. This means that the sound comes out of computer via the MOTU 2408 and out of my Quested monitors (they are active so self-powered) which are attached to the MOTU's outputs.
When I record vocals I sing into my ADK microphone (this microphone sources its own power from its own box which also feeds it Phantom Power) which is connected by a mic to jack cable to the Focusrite compressor which is connected by jack to jack cable to the MOTU 2408 which then goes into my computer via a firewire cable.
When I play keyboards or use my keyboard as a midi controller it connects to my computer via the MOTU micro lite (midi-usb interface).
I don't currently have a keyboard. I used to use my basic Yamaha PSR-540 keyboard as a midi controller but as it's not weighted and faulty I needed to get a new one. We got a new one via Thomann which was the M-Audio Pro Keys 88 keyboard but this quickly became faulty. We returned it and have since been considering other weighted keyboards. I am simply wanting a keyboard with Aftertouch, either 76 or 88 keys, weighted keys and very importantly, hammer action where the action is fast. I don't care for other controllers on the keyboard, on-board sounds, iPad compatibility or whatever.
My Questions:
Q1) Can you recommend any keyboards meeting my specifications?
Q2) I can't imagine any of the Blue or other USB mics competing with my ADK and I'm quite happy with it. For vocals and when I've wanted to play the keyboard in as audio (not as a midi controller) I've used the Focusrite compressor to boost the sound. I'm not using many functions/presets on the compressor as I know it's best to record the sound of vocals mostly raw, is this correct, and if so is it worth me continuing to use this compressor or sell it?
Q3) Do I need to have the MOTU micro lite (midi to usb) unit? Don't most keyboards these days connect direct usb to usb on the computer?
Q4) I'm happy and used to the sound out from my Quested monitors. I'm happy and used to the sound in using my ADK microphone. What do I need for these to work best with the Mac Mini? Is my MOTU 2408 good for this, or is another MOTU product needed, or another product altogether?
Q5) Depending on (Q4) do I need a soundcard installed in the Mac Mini as I read on a forum that these days the audio interface acts like the soundcard?
Q6) I have such a bad connection to the internet it's like I have Dial-up!!! I use Airport Wireless which is connected to a router downstairs, which is 02 Broadband. Internet's not an issue downstairs on my girlfriend's intel PC which also uses a wireless connection but not Airport. Is this a problem because of my Airport, or do I need to get a router for upstairs, or should I connect it directy to the router downstairs by ethernet cable?
Many thanks!

Is there a reason you don't want to use your current Tascam?

Canon scanner not recognised after Mac wakes up.

Hi
I have been using a Canon LIDE 60 scanner since I bought my eMac 4 or so years ago. It's always worked fine.
But since upgrading to Leopard a few months ago I've been having trouble with it.
What happens is that after the Mac goes into deep sleep mode (it's set to have the hard drive sleep too) and the scanner is not recognised after the computer wakes up.
I get an error message when I open up a TWAIN program (CanoScan Toolbox or Image Capture) saying that there is no scanner available.
Sometimes, usually actually, if I disconnect the USB cable and then re-attach it the scanner becomes available again. But sometimes not.
I have what I believe to be the most recent driver for this scanner, dl'd recently from Canon's web site. First I uninstalled the old driver and then restaterd my eMac before installing the new driver.
I'm using whatever version of Image Capture came with Mac OS and I'm using CanoScan Toolbox version 4.9.3.4 (version 5.0 does not work at all).
Any way to get this to stop happening?

Bump
Joey Goldstein wrote:
Hi
I have been using a Canon LIDE 60 scanner since I bought my eMac 4 or so years ago. It's always worked fine.
But since upgrading to Leopard a few months ago I've been having trouble with it.
What happens is that after the Mac goes into deep sleep mode (it's set to have the hard drive sleep too) and the scanner is not recognised after the computer wakes up.
I get an error message when I open up a TWAIN program (CanoScan Toolbox or Image Capture) saying that there is no scanner available.
Sometimes, usually actually, if I disconnect the USB cable and then re-attach it the scanner becomes available again. But sometimes not.
I have what I believe to be the most recent driver for this scanner, dl'd recently from Canon's web site. First I uninstalled the old driver and then restaterd my eMac before installing the new driver.
I'm using whatever version of Image Capture came with Mac OS and I'm using CanoScan Toolbox version 4.9.3.4 (version 5.0 does not work at all).
Any way to get this to stop happening?
Message was edited by: Joey Goldstein

Tascam US-122 MK II not working with Mac Mini

This seems to be a common issue for many people for many years, but I have not found anyone with this exact problem...:
I am using the Tascam US-122 MK II audio interface with my Mac Mini (latest model). I have connected everything correctly, have installed the correct drive (first from the provided disk, then when that didnt work, from the web).
The device is powered and seems to be working. I can see in System Preferences that the mini picks up the signal coming from the US-122 ( a guitar ).
I have then attempted to use it with GarageBand. I have set the input to pick up the US-122. But there is no sound. Garageband registers no input at all, there is no sound at all, and there is also no out sound from the phones on the device. Having checked with Tascam, the problem doesnt seem to lie with the device.
Has anyone had a similar problem? Could it be that I have to reboot in 32 bit? I don't see why this should be the case.... Thanks!

Thanks. This doesnt seem to have helped, but has made me notice something.
In Audio MIDI Set Up under Audio Devices, I am not able to select the US-122 MKII for sound input: that field is not highlighted. I can only select for sound output, which is of no use...! I have absolutely no idea why, even though it recognises the device, it will not allow me to select it for sound input. Any ideas? Thanks again.

Logic Node 9 not working with mac mini

MBP late 2008 4gb ram 500gb hd + New Mac Mini 2009 Base with 1gb ram
Logic Node installed - settings under audio checked... etc
Node working (slightly) see picture
I had to unplug the edirol keyboard, brother laser printer, fw800 drives, 3 usb hard drives, external alu keyboard griffin powermate and turn off airport to get working.
then after it was working I would still get overload messages (see below)
barely sending anything to the node...
[IMG]http://www.musicrowsongs.com/logicnode.jpg[/IMG]
any ideas?
thanx
michael

1.) when node not working it appears to be the fw800 drives
2) when it does work - no major node processing
[img]http://www.musicrowsongs.com/logicnode2.jpg[/img]
Using a lot of high end waves plugs
mercury v6r7 - perhaps Maserati - API - SSL not going into the node? Why?

Mic not working with MAC Mini on Line in

Hi,
Just got my MAC Mini 3 weeks ago - I've just tried using my audio line-in mic to do a test call with SKYPE and it doesn't work.
I've gone into system preferences and tried to adjust the input volume but it doesn't seem to want to know...
Any advice for this MAC newbie?

Welcome to Apple Discussions!
I would say the fact you get some audio from the mic but not enough for viable use indicates that your present microphone is not outputting a high enough signal. Many elecret condeser type mics, and others with battery power sources output below line level voltages, so the input in the mini would simply not be sensitive enough to register the signal, and you would get exactly the results you describe.
There are microphone preamplifiers you could get to boost the mics signal level, or alternatively, a number of other microphones, including almost all USB devices of this type, which would likely serve your purposes very well.

Usb mike not working with mac mini

Hi,
I bought a samson CO1U usb connection mike to use with the mac mini as there is no mike connection. The device is recognised by the computer but apparently not by i-movies or Quicktime Pro 7 as when I bring up the audio screen nothing registers in the sound level and obviously nothing records - am I doing something wrong or missing something out or is this device just not compatible? Apple help were no help!
Hope someone can be of assistance in this matter as I need to record a voiceover on to an animation video.
cheers, shadwell

Hi, thanks for your reply - did that but still no joy.
In utilities / audio midi it says output ( and input ) not supported and in system preferences/sound the input level is registering nothing.I'm going to try the mike on a friend's laptop to see if it is a problem with the mike or the mini mac - or maybe I'm just making some simple mistake in setting it up in Quicktime.Do you know if any usb recording devices actually do work with the mini mac?
thanks, shadwell

Functioning Monitor will not display with Mac Mini

I'm trying to get an IBM E74 CRT monitor working with an early 2009 Mac Mini. I have it connected with Apple's mini-DVI to VGA adapater. The Mac "sees" the monitor since with screen sharing I can see the Display System Preference when the monitor is attached. It shows the monitor as an IBM E74 and allows what appear to be appropriate choices as far as resolution and refresh rate are concerned. I tried many combinations of resolution and refresh rate with no difference in behavior.
The monitor always acts like no signal is detected (built it message on monitor display). This monitor works fine with a B&W G3 and a late 2007 MacBook Pro. Any ideas why the Mac Mini is not driving the monitor? Have tried all combinations cycling power on the monitor, connecting / disconnecting while the Mac Mini is power up. Have had the monitor connected and powered on when booting the Mac Mini. For whatever reason the monitor does not seem to work with the Mac Mini, but works fine with other computers.
The monitor despite its' age has pretty low time on it and is quite serviceable. Are there quirks with the VGA interface that we may be running into? I would like to get this combo working together if at all possible.

I would say the VGA interface did evolve somewhat over that time period. In particular, the thing that may have changed that could be the underlying cause of the problem is sync termination impedance has trended upwards. It's not unusual to find older monitors with low impedance on sync. Some even had 75 ohm impedance, which required a line driver for sync the same as for video.
It could be the IBM monitor has fairly low termination impedance and the mini is unable to provide sufficient output on the sync lines to drive TTL levels, whereas the MBP is doing better. You could check this with a simple ohm meter with the IBM monitor turned off. Ideally, for the mini, you would want to see a high impedance reading on H and V sync, like close to 2k ohms. If it's 500 ohms or less, then the mini may not be able to drive sync properly.
On an old monitor like that, it is likely to have old fashioned components with axial leads rather than surface mount components. If you are handy with a soldering iron, you could find the offending resistors and bring the monitor up to a more modern, high impedance standard of 1.8k to 2.2k.

Apple aluminum keyboard w/o keypad not working with Mac Mini

I'm in the process of reconfiguring our old Mac Mini to run some of our old games that no longer run on the newer Macs. We had a spare Apple aluminum keyboard (without the numeric keypad) which I thought I'd use with the Mini. The alphanumeric keys work fine, but the function keys don't seem to. (In particular, I can't get the volume keys to work.)
I've checked my keyboard settings in System Preferences. Software Update shows everything up-to-date.
The aluminum keyboard WITH the numeric keypad works fine with the Mini. Also the keyboard without the keypad works properly with my Intel iMac.
Does anyone know what's going on?

Hi,
am I right in assuming that you are talking about the Wireless Aluminum Apple keyboard ?
If so, the 2009 version of it requires OSx Leopard 10.5.8 to work properly.
http://support.apple.com/kb/HT1809
The 2007 version of that keyboard requires at least OSX Tiger 10.4.10 plus this keyboard software update http://support.apple.com/kb/HT2394
Maybe downloading and apllying the update can help.
Regards
Stefan

AirPlay mirroring not working with Mac mini mid 2011

I recently upgraded my Mac mini to mountain Lion Osx for being able to use AirPlay Mirroring Feature with my Apple Tv3 5.0.
Normal l'y i should qualify for being able to use this Feature but the only thing i CAN get is a green screen... When activating thé mirroring on the upper right corner Of my desktop screen...???
If somebody CAN help trouble shooting this problem
Thanks

the next thing i would confirm is that there is no network issue. is your mini connected to your home network via wifi, or wired? if it's wifi, then i would try to connect it with an ethernet cable, just for testing purposes. if it's connected via wired connection and that's how you're getting your green screen, then it warrants a trip to visit the "geniuses" (please Apple, don't censor me for putting geniuses in quotes). because you would've effectively isolated the problem to your mini. good luck.

External Isight Not Working With Mac Mini

Hello
Thank You for taking the time to look at this for me , I have 2 external isight cameras and i can get neither one to work with my late 2009 mac mini running snow leopard , although they both work on the latest mac mini (running lion) , When connected they open Ichat Av but i cant get a video from them.
Thanks In Advance

27/10/2012 11:10:33
com.apple.launchd[1]
*** launchd[1] has started up. ***
27/10/2012 11:11:02
com.apple.launchd[1]
(com.parallels.vm.prl_naptd) Unknown key for boolean: SuccessfulExit
27/10/2012 11:11:05
com.apple.WindowServer[79]
Sat Oct 27 11:11:05 Jordan-Bakers-Mac-mini.local WindowServer[79] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
27/10/2012 11:11:34
com.parallels.vm.prl_naptd[129]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
27/10/2012 11:11:34
com.parallels.vm.prl_naptd[129]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
27/10/2012 11:11:34
com.apple.launchd.peruser.501[160]
(com.kodak.BonjourAgent) Unknown key for string: Kodak Version
27/10/2012 11:11:34
com.apple.launchd.peruser.501[160]
(com.kodak.BonjourAgent) Unknown key: Kodak Version
27/10/2012 11:11:34
com.apple.launchd.peruser.501[160]
(com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
27/10/2012 11:11:38
[0x0-0xa00a].SoftwareUpdateCheck[173]
SoftwareUpdateCheck: network unreachable
27/10/2012 11:11:38
com.apple.launchd.peruser.501[160]
([0x0-0xa00a].SoftwareUpdateCheck[173]) Exited with exit code: 3
27/10/2012 11:11:38
com.apple.launchd[1]
(com.apple.suhelperd[175]) Exited with exit code: 2
27/10/2012 11:11:43
com.parallels.vm.prl_pcproxy[190]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
27/10/2012 11:11:43
com.parallels.vm.prl_pcproxy[190]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
27/10/2012 11:11:43
com.apple.launchd.peruser.501[160]
(com.apple.Kerberos.renew.plist[187]) Exited with exit code: 1
27/10/2012 11:11:44
WitnessUserAgent[191]
WitnessUserAgent r304 started for user 501
27/10/2012 11:11:54
WitnessUserAgent[191]
Connected to daemon: <BUDaemonServer: 0x10ea50>
27/10/2012 11:12:26
uclocator[192]
Core Location could not establish your current location
27/10/2012 11:12:26
uclocator[192]
Error Domain=kCLErrorDomain Code=0 "The operation couldn’t be completed. (kCLErrorDomain error 0.)"
27/10/2012 11:12:39
System Preferences[217]
.scriptSuite warning for result type of command 'timedLoad' in suite 'SystemPreferences': the type NSNumber ('long') doesn't match the result Apple event code ('doub').
27/10/2012 11:12:59
com.apple.launchd[1]
(com.apple.xprotectupdater[34]) Exited with exit code: 255
27/10/2012 11:13:11
com.apple.launchd.peruser.501[160]
(com.apple.AirPortBaseStationAgent[189]) Exited: Killed
30/10/2012 16:51:29
com.apple.launchd[1]
*** launchd[1] has started up. ***
30/10/2012 16:51:55
com.apple.launchd[1]
(com.parallels.vm.prl_naptd) Unknown key for boolean: SuccessfulExit
30/10/2012 16:51:56
com.apple.WindowServer[87]
Tue Oct 30 16:51:56 Jordan-Bakers-Mac-mini.local WindowServer[87] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
30/10/2012 16:52:00
com.apple.launchd[1]
(com.apple.xprotectupdater[33]) Exited with exit code: 252
30/10/2012 16:52:10
com.parallels.vm.prl_naptd[136]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 16:52:10
com.parallels.vm.prl_naptd[136]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 16:52:10
com.apple.launchd.peruser.501[160]
(com.kodak.BonjourAgent) Unknown key for string: Kodak Version
30/10/2012 16:52:10
com.apple.launchd.peruser.501[160]
(com.kodak.BonjourAgent) Unknown key: Kodak Version
30/10/2012 16:52:10
com.apple.launchd.peruser.501[160]
(com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
30/10/2012 16:53:35
com.parallels.vm.prl_pcproxy[196]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 16:53:35
com.parallels.vm.prl_pcproxy[196]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 16:53:36
WitnessUserAgent[197]
WitnessUserAgent r304 started for user 501
30/10/2012 16:53:36
com.apple.launchd.peruser.501[160]
(com.apple.Kerberos.renew.plist[193]) Exited with exit code: 1
30/10/2012 16:53:50
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:50
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:52
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:52
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:52
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:53
WitnessUserAgent[197]
Connected to daemon: <BUDaemonServer: 0x401100>
30/10/2012 16:53:54
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:55
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:53:55
Photo Booth[182]
*** <QCNodeManager | namespace = "com.apple.QuartzComposer" | 391 nodes>: There is already a node registered with name "/userbackdrops"
30/10/2012 16:54:25
uclocator[198]
Core Location could not establish your current location
30/10/2012 16:54:25
uclocator[198]
Error Domain=kCLErrorDomain Code=0 "The operation couldn’t be completed. (kCLErrorDomain error 0.)"
30/10/2012 16:55:07
iChatAgent[225]
[Warning] [AIM] Could not change my visibility to 0
30/10/2012 17:01:48
[0x0-0x1c01c].com.skype.skype[258]
WirelessAttach: IOServiceOpen error: e00002c7
30/10/2012 17:01:48
[0x0-0x1c01c].com.skype.skype[258]
WirelessAttach: IOServiceOpen error: e00002c7
30/10/2012 17:01:49
[0x0-0x1c01c].com.skype.skype[258]
WirelessAttach: IOServiceOpen error: e00002c7
30/10/2012 17:01:49
[0x0-0x1c01c].com.skype.skype[258]
WirelessAttach: IOServiceOpen error: e00002c7
30/10/2012 17:04:01
iChat[222]
------ startPreview: previewing: 2
30/10/2012 17:04:23
iChat[222]
------ startPreview: previewing: 2
30/10/2012 20:38:13
com.apple.launchd[1]
*** launchd[1] has started up. ***
30/10/2012 20:38:45
com.apple.launchd[1]
(com.parallels.vm.prl_naptd) Unknown key for boolean: SuccessfulExit
30/10/2012 20:38:48
com.apple.WindowServer[78]
Tue Oct 30 20:38:48 Jordan-Bakers-Mac-mini.local WindowServer[78] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
30/10/2012 20:38:48
com.apple.launchd[1]
(com.apple.xprotectupdater[33]) Exited with exit code: 252
30/10/2012 20:39:07
com.parallels.vm.prl_naptd[129]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 20:39:07
com.parallels.vm.prl_naptd[129]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 20:39:07
com.apple.launchd.peruser.501[158]
(com.kodak.BonjourAgent) Unknown key for string: Kodak Version
30/10/2012 20:39:07
com.apple.launchd.peruser.501[158]
(com.kodak.BonjourAgent) Unknown key: Kodak Version
30/10/2012 20:39:07
com.apple.launchd.peruser.501[158]
(com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
30/10/2012 20:39:11
com.parallels.vm.prl_pcproxy[184]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 20:39:11
com.parallels.vm.prl_pcproxy[184]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 20:39:11
com.apple.launchd.peruser.501[158]
(com.apple.Kerberos.renew.plist[181]) Exited with exit code: 1
30/10/2012 20:39:11
WitnessUserAgent[185]
WitnessUserAgent r304 started for user 501
30/10/2012 20:40:09
com.apple.launchd[1]
*** launchd[1] has started up. ***
30/10/2012 20:40:35
com.apple.launchd[1]
(com.parallels.vm.prl_naptd) Unknown key for boolean: SuccessfulExit
30/10/2012 20:40:36
com.apple.WindowServer[87]
Tue Oct 30 20:40:36 Jordan-Bakers-Mac-mini.local WindowServer[87] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
30/10/2012 20:40:38
com.apple.launchd[1]
(com.apple.xprotectupdater[33]) Exited with exit code: 252
30/10/2012 20:40:49
com.parallels.vm.prl_naptd[128]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 20:40:49
com.parallels.vm.prl_naptd[128]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 20:40:49
com.apple.launchd.peruser.501[159]
(com.kodak.BonjourAgent) Unknown key for string: Kodak Version
30/10/2012 20:40:49
com.apple.launchd.peruser.501[159]
(com.kodak.BonjourAgent) Unknown key: Kodak Version
30/10/2012 20:40:49
com.apple.launchd.peruser.501[159]
(com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
30/10/2012 20:40:50
com.apple.launchd.peruser.501[159]
(com.apple.Kerberos.renew.plist[182]) Exited with exit code: 1
30/10/2012 20:40:50
com.parallels.vm.prl_pcproxy[185]
QKqueueFileSystemWatcherEngine::addPaths: open: No such file or directory
30/10/2012 20:40:50
com.parallels.vm.prl_pcproxy[185]
QFileSystemWatcher: failed to add paths: /Library/Managed Preferences
30/10/2012 20:40:50
WitnessUserAgent[186]
WitnessUserAgent r304 started for user 501
30/10/2012 20:40:52
WitnessUserAgent[186]
Connected to daemon: <BUDaemonServer: 0x10f390>
30/10/2012 20:41:30
uclocator[187]
Core Location could not establish your current location
30/10/2012 20:41:30
uclocator[187]
Error Domain=kCLErrorDomain Code=0 "The operation couldn’t be completed. (kCLErrorDomain error 0.)"
30/10/2012 20:42:21
com.apple.launchd.peruser.501[159]
([0x0-0x11011].com.apple.iChat[209]) Exited: Terminated
30/10/2012 20:44:07
iChatAgent[230]
[Warning] [AIM] Could not change my visibility to 0
30/10/2012 20:44:41
iChat[228]
------ startPreview: previewing: 2
30/10/2012 20:45:26
com.apple.launchd.peruser.501[159]
([0x0-0x18018].com.apple.iChat[228]) Exited: Killed

Magic trackpad not working with mac mini

I have a new Mac mini and I paired a wireless trackpad and magic trackpad. I paired the trackpad with my MBP and it works exactly like the trackpad on my MBP. When I use the trackpad with the mini, I can't get it to "right click" or two finger scroll. For example, if I'm in iTunes, and want to scroll through my library, a two finger scroll on the trackpad just moves the curser, the only way I can move up and down on a page is to use the arrows. I can't get it to give me anything with a right click. When I go to System Prefrences, it only shows "keyboard" and "mouse", but no set up options for the trackpad. And under the mouse settings, it doesn't give me any "secondary" click options. What am I missing?

I had the same problem. Rebooting the computer fixed the issue for me.

Piano keyboard not communicating with Mac

I have installed the driver for my Yamaha keyboard, but it's not connecting with the Mac. Is there a step I'm missing?
Thx,
Redhousearts

The Yamaha support site shows drivers from OS 8 (1997) which makes this a very old machine indeed. The site shows it to be discontinued, as you say. The keyboards of that vintage used a cable MIDI to USB which is now difficult to find widely available since most recent controllers are USB interface. It seems that you will have to consider a more up-to-date controller for use with your Mac. I have used M-Audio controllers with a great deal of reliability in conjunction with my Macs causing no trouble for driver and recognition: simply plug and play with both GarageBand and Logic as well as Finale (for Speedy Entry using MIDI input). I find the M-Audio reasonably priced and effective for my studio work at my DAW. My current controller is M-Audio Oxygen 49; no concerns on iMac and MacBook Pro (10.6.8)in addition to MacBook Pro (10.7.2). Good luck in your search.

Mini DP to HDMI does not work with Mac Mini 2014?

Hi All,
I just upgraded from a Mac Mini 2011 i5 to a Mac Mini 2014. My old Mini worked fine running 2 displays with an HDMI cable to one monitor and a Mini Displayport to HDMI from the Thunderbolt port to another monitor. I can't seem to get the new 2014 Mini to see the monitor from either the Thunderbolt ports. Is this no longer supported?
Thanks
Ray

Hi there LaureynR,
You should still be able to do this. I would recommend taking a look at the article below for troubleshooting steps.
Apple computers: Troubleshooting issues with video on internal or external displays
-Griff

Apple Remote not working with Mac Mini

Hi there,
I woke up to quite a strange problem today... My Apple Remote is no longer working with my Mac Mini! I tried all the controls, including launching front row, and the volume controls - but no go...
I even tried it in Windows BootCamp under iTunes, but it still wouldn't work..
I tried pairing it in System preferences, but again, it wouldn't recognise my apple remote when i held down the Menu+fast forward keys for 5 seconds...
The weird thing is, it works fine with my iMac on another floor (out of plain sight from my Mini..), and it isn't paired with the iMac or anything...
Any idea what the problem might be? Thanks in advance!

So you got a dead remote or a dead battery. Call AppleCare and it will be taken care of. What's the big deal? These things happen from time to time.

Canon scanner not communicating with mac min using OS 10.5.8

Similar Messages

Maybe you are looking for