Cant access Router's Web Based Management anymore

WRT54G v5
All of a sudden, i cant access the web management pages for my router. I have reflashed using the TFTP program and no change. I have tried resetting my router and it doesnt reset. Anyone have any ideas what else to try?

What I did was a hard reset... (hold reset for 10 or 30 seconds then while holding, unplug unit then release reset button. After 10 more seconds, plug unit back in.)
Between that and using the TFTP program, I was able to get back into my management screen. You will have to reconfigure your router after that. Be sure, if you have a dedicated ip on your computer, you temporarily set it to obtain everything automatically incase your set ip doesnt correspond to the default settings for your router. Then once everything is back up, you can change you ip settings on your PC back to what you had, if any.

Similar Messages

Can't Access Router's Web-Based Setup Page

I have tried this: http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3676
Entering in the default IP and my actual IP address does not work, I'm trying to find out what my security key is.
Solved!
Go to Solution.

When you Hardwired your computer to the Router, on your computer click on Start - Run - CMD and click ok, now in the Command Prompt window type "ipconfig" and hit enter.. Note down the Default Gateway IP address.
Open IE on your Computer and in the address bar type http://default gateway ip and hit enter,when prompted for the Username and Password, Leave the Username blank and type "admin" as a password and click Ok. (If you have changed the Router password, then you need to use that password to login to the Setup page of your Router).
Once you login to the Router setup page, click on the Wireless tab and then click on the sub tab "Wireless Security" and in the window you will find out your security key.

Cannot connect using Accessing the Router's Web-Based

I'm trying to update firmware, I have done all the step to access the router's web-based.. I connected DSL to the Ethernet port on the router, from the router I used another Ethernet cable to connect the router to my laptop.. I can't get an internet connection. The reason why I'm doing the update I have been using WRT54G2 V1 with no problems, all at once I can't connect to the internet using the router. I was told that I need to perform a firmware update.
Thank you for the help

What' s the ip address and the default gateway are you getting on the computer ?
Connect the DSL modem to the Internet port of the router then use port number one on the router to connect the computer.
Click on Start > Run > type CMD hit Enter command promt window will appear on the screen.
In the command promt window tupe "ipconfig" hit Enter. Now you will see the ip address and the default gateway on the screen. Use the default gateway to open the setup page of the router.

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page.
I have tried everything posted to the forums and the Knowledge Base for several weeks now with no luck. I can power push router and gain access to router's web-base interface but only for a few minutes than it quits loading part way through and or does not load at all. If I turn off the wireless side I can access the router at will with no problems. My warranty is almost over. I am at my wits end. I would like to get it replaced under warranty if I can. (^8
Solved!
Go to Solution.

Thank you for your recommendations peanuts. (^8
I bought the router back in December 10, 2006.
I updated the firmware to v1.00.20 back in June 2007. After I did a successful firmware upgrade I reset the router to factory default settings and then reconfigured it. It has worked Ok till a couple of months ago.
I have read everything I can find here on the support forum and in the Knowledge Base several times.
I have tried changing all the different settings to the different recommendations posted here and in Knowledge Base with no success. Each time I would do a long reset back to factory defaults, let it soak for a few hours and then make one change at a time and let it soak.
I have been monitoring 6 other wireless AP(s) around me (none mine) for a couple of months too. None of them are strong enough to connect to. My SSID is different from them. I have tried all the channels. My router is passworded and MAC'd.
It is looking like it is time to call support and try to get a replacement under warranty while it is still in affect.

Error in router's web-based setup page (WRT54G V5)

Hi,
My router’s web-based setup page is unable to load fully.
There seems to be an error with some document.setup.save file.
I have tried to reset my router but the router’s web-based setup page is still unable to load fully.
Please help.
Thanks.

Try Internet Explorer, it usually works.
JavaScript must be enabled.
Temporarily turn off your computer's software firewall, and see if that corrects your problem.
Hope this helps.

Unable to access the Router's Web-Based Setup Page

Hey, I found a little problem when I tried to change the configurartions to my Linksys WRT54GS ver- 6.0 router. Problem is that I can not acces to setup, nor can I connect to Internet trough wire. Can somebody help me with my problem?
Pasi

To view the router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

Cant Access Server Admin and Server Preferences anymore

After upgrading to the latest Mac OS X 10.6.5 Version and/or changing Admin Password (I dont know the reason yet) I dont have access to my Server Admin and Server Preferences while I still can use my Workgroup Manager including Directory Admin (driadmin) and System Preferences. My Client Macs cant access Filesharing services and timemachine backup service anymore on the server, too. Other Services like MyEyeTV, Wuala, iTunes are working fine on the server and can be used by my Client MACs in my LAN.
How could I proceed to fix this issue?
What I have tried so far:
I have tried to access my Server Admin thru the Client Mac mini using Server Admin App.
I checked the OS Version: Mac OS X Server 10.6.5 (10H575)
I checked the Server Admin Version: 10.6.5 (328.4)
I also reinstalled the latest MAC OS X Server Update 10.6.5
I still have root access. (Verified by DataQuest Engineer)
Used also 127.0.0.1 Address to Access the Server.
Is there a more elegant way to fix this issue than reinstall the server?

... well uninstalling "Hands Off!" Application solved the problem.
Also if I assumed that i disabled this application, it was still active.

Cant access router's login page

my macbook cant access the router's login page,but i cant access the internet through this wifi
here is some info i think may be useful
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 80:e6:50:00:a0:c6
inet6 fe80::82e6:50ff:fe00:a0c6%en0 prefixlen 64 scopeid 0x4
inet 192.168.2.101 netmask 0xffffff00 broadcast 192.168.2.255
nd6 options=1<PERFORMNUD>
media: autoselect
status: active
en1: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:91:16:20
media: autoselect <full-duplex>
status: inactive
en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:91:16:21
media: autoselect <full-duplex>
status: inactive
bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=63<RXCSUM,TXCSUM,TSO4,TSO6>
ether 82:e6:50:00:cc:00
Configuration:
id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
ipfilter disabled flags 0x2
member: en1 flags=3<LEARNING,DISCOVER>
          ifmaxaddr 0 port 5 priority 0 path cost 0
member: en2 flags=3<LEARNING,DISCOVER>
          ifmaxaddr 0 port 6 priority 0 path cost 0
nd6 options=1<PERFORMNUD>
media: <unknown type>
status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
ether 02:e6:50:00:a0:c6
media: autoselect
status: inactive
Internet:
Destination        Gateway            Flags        Refs      Use   Netif Expire
default            192.168.2.1        UGSc           28        0     en0
127                localhost          UCS             0        0     lo0
localhost          localhost          UH             34 2643545     lo0
169.254            link#4             UCS             1        0     en0
169.254.71.63      74:2f:68:73:6d:e   UHLSW           0        0     en0    281
192.168.2          link#4             UCS             2        0     en0
192.168.2.1        94:c:6d:30:49:de   UHLWIir        29      178     en0   1029
192.168.2.101      localhost          UHS             0        0     lo0
192.168.2.102      74:2f:68:73:6d:e   UHLWI           0        0     en0    290
If some people cant help I'll really appreciate.

What I did was a hard reset... (hold reset for 10 or 30 seconds then while holding, unplug unit then release reset button. After 10 more seconds, plug unit back in.)
Between that and using the TFTP program, I was able to get back into my management screen. You will have to reconfigure your router after that. Be sure, if you have a dedicated ip on your computer, you temporarily set it to obtain everything automatically incase your set ip doesnt correspond to the default settings for your router. Then once everything is back up, you can change you ip settings on your PC back to what you had, if any.

Can not login to my EA4500 router's web based setup page

Hello All-I have a EA4500 router. I attempted to login to my router' web based setup page late last year using my IE11 browser.I received an error message stating that I cannot login with that browser. I need an updated IE,Google Chrome or Mozilla Firefox to be able to visit that site. I attempted about 3 more times and received the same error message. I switched to Google Chrome that worked very well up to tonight(3/31/2004). Cisco web page is preventing me from opening my setup page. I believe I should be contacting Customer Support about this problem but none of their support options cover this problem. Thanks in advance.

IE 11 isn't compatible. Use Google Chrome if you don't want to uninstall IE 11 and go back to IE 10.
You can force the local login by disconnecting the cable from the router's internet port and then logging in.
If the Smart Wifi is giving you trouble and you don't mind reconfiguring your router. Then you could disable Smart Wifi services.
To disable Smart Wifi Services:
Reset the router to factory defaults (recessed button for 30 seconds or through the router UI)
For setup choose "I want to skip Setup and configure my router manually"
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

How to administer an Access database via web-based interface?

There are times when I need to edit a database record to do something my CMS wasn't designed to do, so I have to manually edit it. Normally I just ftp the Access mdb file to my pc, make edits, and reupload the mdb file and hope nobody updated the database in the meantime. Does anyone know of a web-based database admin system that will allow me to edit Access data? Sure would be nice if I could install something on the server that would allow me to edit any datasource there and not have to have a separate, customized interface for each datasource.
Thanks for looking, Bill

I would recommend naming that page with an extension that the web server will not serve. Rename it to use it and then rename it back when done.
Or just put access restrictions on it via the web server, so one needs to authenticate to the system before using it.
Or stop using Access and use a decent DB: Access is not appropriate to be used as a DB for a web application. But that might not be an option.
Adam

500 Internal error observed while accessing a Static Web based course

Hi Experts
When I try to start a static web-based course in portal, a 500 Internal server error comes up on the screen and the course not played at all.
Please suggest.
Regards
Shaily

Hi Shaily,
Give some more details about product and also share screen shot for error
Regards,
Dhuvaraganathan M.

Error accessing Infoview and web-based Administration Console

Post Author: rsir
CA Forum: WebIntelligence Reporting
After installing Business Objects 6.5.1 with SP3 in a single server as a primary node, everything works fine, except for the InfoView (wiasp) interface and the web/based administration interface (wiadmin). We've investigated in the BusinessObjects support site and in many forums about the problem and tried every single possible solution in order to correct the problem, without success.
The system we're working on is this:
Server model: Hewlett-Packard BLADE series BL 460C
OS: Windows 2003 SP1
Web Server platform: IIS6
What happens is that when we try to log in to infoview in the welcome screen, the url changes to:
http://(servername)/wiasp/scripts/login/webiStart.asp
And it displays the "The page cannot be displayed" error.
Also, when trying to log in to the web-based administration console (the client version works fine), it displays this error:
"The system is not started (Error: ADC 00071)"
We've tryed enabling parent paths in the IIS, redeploying the cluster node throught the configuration tool, checking the web extensions to be allowed, etc. without success.
Thank you very much in advace for any help.
Roderic Sir

Post Author: sarika_us
CA Forum: WebIntelligence Reporting
Hi,
I am facing the same problem. Could you please tell me how you resolved it.

Router's Web-based page not loaded correctly.. Need Help!!

I'm using WRT54G v2.2 router and recently i noticed tat i've flashed a wrong firmware which is WRT54GL version, so wat i did was i flash the original v2.2 firmware which i noticed it had not been updated since 2007... after i flashed the router and i log into the 192.168.1.1 webpage.. all the tabs and many options are missing as though the page was not loaded correctly or fully loaded and i cant even get into the management page and so on..
I really need help on this..

Hold the reset button down for 30seconds and then release it. Unplug the power cable for 10 seconds. try accessing the set up page once again and see if it makes a difference.

AnyConnect - cant access router's lan, but everything else is reachable.

Hello,
i have a strange problem which i am trying to resolve, but i have run out of ideas.
I have a router on which i have Anyconnect as RA , and DMVPN to form S2S vpn with other locations.
I can successfully connect to router via anyconnect, it will push a routing to the clients ok. I can ping all router interfaces, and even the remote lans.
But i cant ping any computer on local lan of the router. Its not the problem of the firewall on router (zbf) as i have tried to disable it completely with no effect.
I have also tried to connect via anyconnect to other router in the dmvpn network and i can access my local lan.

Hmmm, i have added access-list 105 deny ip 192.168.5.0 0.0.0.255 192.168.5.0 0.0.0.255
just to be sure but it does not fix the issue.
Which is expected from my side as the anyconnect vpn pool is " ip local pool SSLVPN-POOL 192.168.5.200 192.168.5.210 and svc address-pool "SSLVPN-POOL" netmask 255.255.255.0
" . As my local subnet is 192.168.5.0/24 it is in the same subnet so there should not be NAT taking place. Or am i mistaken somewhere ?
I do not have ip nat inside statement on virtual-template1 also.
Will try to extend the SSLVPN-POOL to the whole subnet or changing the subnet for it, to see if this has any effect.

After installing all lenovo updates for n500 I cant access the boot rescure and recovery anymore!!!

hi,
i´ve just installed all actual updates for the n500, including a bios update. since then I cant get into the boot up utilities(I think its called thinkvantage) anymore with the lenovo button when booting up (instead, I get a menu where I can choose where to boot from!!!!)... when pressing f8 on bootup there used to be something like "repair system" in the menu, its gone too...
also, rescure and recovery in vista basic does not load anymore, the gui process is running but nothing happens... please help!!!
what can I do??? I didn't touch any partitions or delete anything... before the updates, it did work. installing the newest bios from the website did not solve the problem too...
Message Edited by herbun on 06-19-2009 04:53 AM

I am beginning to love lenovo. and vista. I´ve used the boot disk found at http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-54483
(vista version), made a disc with it, "fixed" my mbr... and now vista stops booting all together. something about a missing bootmanager. I love it. really. both. lenovo, and vista.
edit: lucky me, I had a dart cd to repair the boot manager. so I can at least boot again. but, still no solution to my problem... any ideas?
edit 2: I tried again. this time, no error. but still, I have the same problem with a not working thinkvantage. any ideas?
edit 3: seems like the only solution left after reviewing all hints and tips is installing rescue and recovery, but has anyone installed it on a N500 yet? does it work? does it damage the pc? which version should I install, if it works?
Message Edited by herbun on 06-19-2009 06:17 AM
Message Edited by herbun on 06-19-2009 06:33 AM
Message Edited by herbun on 06-19-2009 06:40 AM

Cant access Router's Web Based Management anymore

Similar Messages

Maybe you are looking for