Cant communicate between nodes on the same vlan but on different switches (cat/nexus)
Very odd situation that I cant quite figure out.
I have two nexus switches connecte together with PO5
Each Nexus has PO6 which connects to a Cat3750
The nodes are all on vlan 46.
Nodes that are connected to the nexus switches can ping each other but cant ping other nodes on the cat. switch.
Here is an oddity. Nodes on the CAT switch CAN ping nodes on the nexus switches.
It would appear that the nodes on the nexus (or the switches themselves) do not get the arp requests.
Oddity 2. When I do show vpc I see on one of the nexus vlan 46 is active
id Port Status Consistency Reason Active vlans
6 Po6 up success success 1,31,34,46,200,600-605
When I look at the other switch I dont see vlan 46.
id Port Status Consistency Reason Active vlans
6 Po6 up success success 1,31,34,200,600-605
Comparing the configs I dont see a difference between the two (eyeballing sho run)
Here are the running configs for PO6 on both switches (identical)
MTL-N3548COLO-1# sho run int po6
interface port-channel6
switchport mode trunk
spanning-tree port type normal
speed 1000
vpc 6
Not sure what I am missing. Any help is appreciated.
Thanks
Drew
Your setup with vMotion on a separate subnet is absolutely correct. For the vMotion issues I'd suggest you google for vMotion 14% which will list a couple of KB articles with possible issues and resolutions/workarounds.
André
Similar Messages
-
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
I can't print from my iPad2 to my air-print enabled printer (HP Premium e-all-in-one C310). They're on the same network, but have differed IP addresses! The iPad IP is 192-168-1.126 and the printer is 192-168.1.133. That's the only difference I can see. Is there a way to fix this?
fyi:
you put periods between the numbers.
Each device needs a unique number.
for the 192.168.1 the right must number should vary. 192.168.1.x
the numbers you have look ok.
Power off all devices: wifi router, printer, ipad.. wait 10 minutes. poweron router ... wait power on printer wait then power on ipad.
cross fingers.
Robert -
Can you use 'Home Share' where there are 2 itunes on the same computer, but under different user profiles?
check out method one from this support article -> How to use multiple iPods, iPads, or iPhones with one computer
-
Can you add to the Lightroom an ability to process several raw files with the same content but with different exposure into the single picture?
Base raw files can be given with exposure bracketing during shooting, for example.
The goal - to get maximum details in darks and lights (if we use the "ligths recovery" or "fill lights" we lose the quality because raw file just have no all required information).
The similar (but not the same, only the idea) thing - is High Dynamic Range Photography in Adobe Photoshop
Thank youThe plugin LR/Enfuse does this already. And of course Photomatix have a plugin available for Lightroom. This essentially amounts to pixel editing, which is beyond the range of Lightroom's metadata editing.
-
iCal has dropped a monthly event for the previous four months....... why did it disappear? and where is it? It was the same event but a different day each month.
I installed this same digitizer in my T|X some weeks ago. Some discussion of my experience may be found in this Usenet posting and subsequent thread.
The stock digitizer in my T|X had always had some significant alignment issues (for which PowerDigi was able to compensate very nicely) and sensitivity which was uneven, but which usually required a heavier touch than I liked.
Eventually, it began to develop a “dead spot” near the upper left. My T|X was under warranty, so I probably ought to have sent it in to Palm to be repaired, but I wasn't willing to be without it for the required amount of time, and I've heard enough reports of other T|X owners getting unsatisfactory results this way. I'd heard enough good reports about the PDAPARTS.COm digitizer, that I decided that the only acceptable way to repair my T|X would be to install one of those.
After however many weeks it has been, I am still very pleased with the results. It continues to work flawlessly; it is much more sensitive, so it doesn't require nearly so heavy a touch, and I very much like the hard feel that it has, compared to the spongier feel of the stock digitizer.
My wife's T|X still has its stock digitizer, and it has so far not shown any of the same problems that mine did, or for which the T|X has become notorious, but the feel is noticeably inferior. She's content with it the way it is, but I think that if I were to ever buy another T|X for myself, I wouldn't wait for the stock digitizer to fail. The PDAPARTS.COM digitizer is simply superior in every imaginable way; and, in my opinion, a T|X with the PDAPARTS.COM digitizer installed is sufficiently superior to one with the stock digitizer (even if it isn't defective) to be very much worth the expense and trouble of installing it.
Post relates to: Palm TX -
Can I synch 2 phones to the same iMac, but have different address books?
If you and your wife have separate user accounts on the Mac, then each of you will have separate libraries to sync. You can them maintain separate address books, calendars, apps, etc.
-
I recently set up a new iTunes account for my son by giving him his own Apple ID & own login on the Mac we own.
In addition I have an existing iTunes account with a different Apple ID & different login on the same Mac.
We would like to share some purchases but do not know how to copy or import certain files. The summary is two
different apple ID's, different iTunes libraries, on the same computer, but different parts of the hard drive.
Please advise. Thanks.Load the library which doesn't contain the songs and drag them into the open iTunes application window. If you need to move them between different computer user accounts, put them into /Users/Shared/.
(74502) -
How can I access a response file on the same computer but with different login?
When trying to access a response file on the same computer that was used to set it up, but with a different login, I get an error message that the network resource was not found. How can I retrieve the responses on the same computer but under a different login/username?
The response file is associated with a specific login (as determined under Edit > Preferences > Identity) so you cannot retrieve it if you're using a different login.
-
Hi,
Hopefully someone can help. I have the application "djay" and in two different menus there is the action "Eject". I was wondering if it's possible to apply different keyboard shortcuts to those actions with the same name? I can't see how to do it as it seems you can only write the action but as there are two it doesn't seem to work for me.
For example:
djay>Table-1>Eject - ⌘⇧1
djay>Table-2>Eject - ⌘⇧0
Thanks in advance for any help!!A NodeList doesn't only contain 1 element. In your example it contains ALL <Data> elements inside the document.
NodeList nodes = document.getElementsByTagName("Data");
System.out.println(nodes.getLength() + " \"Data\"-elements found");
for(int i=0; i<nodes.getLength(); i++) {
Node node = nodes.item(i);
} -
I recently authorized my iphone to my wife's imac and synced them so we could share music and apps. Can we both still use separate apple id's to purchase apps and music and still share them?
Kappy wrote:
Unfortunately, apps and music purchased under one Apple ID cannot be shared with a device on a different Apple ID.
Sorry Kappy, not quite true:
Here's how to do so using different computers:
Transfer what content you want to the separate iTunes library on each computer. To transfer content from your library to your wife's library so that she can use it on her phone or from your wife's library to your library, do this:
1. Launch iTunes under your wife's login.
2. Sign her out of iTunes & then you sign in.
3. iTunes>Preferences>Devices>Disable auto-sync when an iPod/iPhone is connected.
4. Connect your phone, DO NOT SYNC!
5. Store>Authorize this Computer(only have to do this once).
6. File Transfer Purchases(all of the purchased content on your phone will be transferred to your wife's library).
7. When complete, eject your phone, sign out of iTunes, sign your wife back in.
You can now sync whatever content you want to your wife's phone. Just remember, all updates to apps obtained using your account must be done while signed in using your account: sign wife out, you sign in, update apps, you sign out, sign wife in, sync her phone.
This way you can share content(permitted under the EUSLA) and still maintain your separate logins. Do the same on your computer if you want to share content from your wife's library.
Just load whatever content you want to share on each others phones, transfer the content, then delete it from the respective phone if you don't want to keep it there. -
I have a street address and a billing address. A question is posed with a checkbox — "Is the billing address the same as the street address?" If Yes is checked, the street address automatically fills the billing fields. If No is checked, the user must fill in new information. In both the street address and billing addres, the State field is a drop-down list. How can I get the drop-down list selection in the street address State also be selected in drop-down list for the billing address State?
Has anyone done this?
-
Two ODSs share the same InfoSource but with different updata mode load?
We've got two different ODSs (ODS1 and ODS2) for two respective clients (client 1 and client 2). Client 1 has already going alive and in the InfoPackage, we only pick up ODS1 (Client 1) as feeding target and we have conducted initial load and several times of Delta loads for ODS1 (data load daily). But now we are going to start to load data to ODS2 (Client 2) and at the same time we will have to continue our delta load to ODS1.
It could not be possible that the two ODSs will be feeded data with different pace (ODS1: continue delta load, ODS2: initial load) if they share the same InfoSource. Then what's the best way to resolve this issue?
Thankshi Pradip,
Tell you a bad news that the solution doesn't work on two of the EBP (a source system which is similar to R3, we've got 4 EBP ODS/InfoSources, but two of the four don't work with the last step listed below) ODSs/InfoSources. The steps I took on production are:
1. Conduct Full Repair data load to ODS2;
2. Delete init option of ODS1 from Scheduler menu;
3. Run Init without data transfer to set delta pointer for both ODS1 and ODS2.
But the last step to run Init without data transfer has taken 1 whole day and eventually becomes red since it takes so long time to set delta pointer.
When I said our solution worked is that I conducted the test on our GL ODS and the Init without data transfer took about 1 hour to finish.
Also when we conduct the last step to do the Init without data transfer to click Start button to set pointer, a msg box titled "Activate ODS Data" pops up saying that "No requests have been selected for activation. Do you want to make a selection, or activate all the requests?" with buttons "Activate all requests", "Select requests" and "Cancel". If clicking the button "Select requests", another msg box pops up to prompt to input a Date range, we didn't input any date range, just click continue, then the Init without data transfer will run forever!
Thank
Message was edited by: Kevin Smith -
Can you sync two iphones to the same computer but with different itunes account
i have got an iphone 4 and my brother would like to get one but we are unsure whether we can both sync our phones on the same computer, within him ended up with all my music and photos. is there a simple way round this?
check out method one from this support article -> How to use multiple iPods, iPads, or iPhones with one computer
-
Several layered effects of the same kind but with different adjustments for the same layer
Hi,
I wonder if it there is an easy way to have several different instances of e.g. glow or bevel and emboss on the same layer.
I know I can achieve this by using smart objects or a duplicate layer with zero blending.
I just wondered if there is a way to do this directly in the layer effects.Hi emil emil,
thx for your answer!
I wasn't even refering to different objects on the same layer, btw. it would be enough if I was able to layer e.g. different bevel and emboss on top of each other (With different colors, softness and size.) But I guess the answer remains the same.
Maybe you are looking for
-
How do you use web inspector with Windows 7
I plug in the USB cable from my Windows desktop to my phone, The drivers are loaded successfully, but where can I find the Windows equal to Safari's advanced preferences.
-
VPN Access to an IP that can be accessed via EIGRP
I have a question. I have a VPN that sits on the external interface using the IP of 10.5.79.X/20. I have a production network connected to a corporate network using MPLS and EIGRP to share the routes. The production network can access the corporate n
-
Dynamic link new feature or bug
If I create an Encore project comprised of dynamic-link sequences from Premier and build a DVD, that works fine. However, if later I change one or more of the sequences in Premier, save everything, and open Encore, it does not know that some of the
-
Uploaded BP Master Data Card with excess character such as "
Hello, I successfully uploaded the BP master data for the new company I created. However, as I checked the BP Master Data form some of the Vendor Name I uploaded have an extra character (double quote) - " for ex.: In my template its only - ACETECH, I
-
Hi all, Facing some problems in changing Infotypes. Scenario: Have to add another tab with some Input fields in the standard Infotype 0045. Problem: Have added the tab with the fields . But the fields are appearing as output fields and moreover even