Cant connect to the WRE54G setup page.

Title says it all!
I can't seem to connect to the setup page, the request keeps timing out.
The router is a WRT54G V2.2
The expander seems to work, it can find the Wireless network if I remove the WPA2 security encryption. That's not something I want to do since I dont want any filthy pirates on my network!
I tried plugging it directly into the router, the computer. Unsure about my IP address though. It should be fine since my gateway seems to be 192.168.1.1
I appreciate any help.

First of all connect the WRE54G with the Router through the Cable and then connect a Computer with the Router through a cable again.
Then try opening up the setup page of the WRE54G with the Default IP address 192.168.1.240 if that doesn't work then reset the WRE54G and power cycle.. As the lights gets stable then try to open the setup page again with the Default IP address 192.168.1.240 and try updating the firmware as well by downloading it from the Cisco website...
Secondly the highest Security Mode that can be set is - WPA Pre-shared Key..

Similar Messages

I just bought an airport express. i set it up and was able to be detected by my macbook, but i still cant connect wirelessly. the same goes when i tried my iphone. please help!

i just bought an airport express. i set it up and was able to be detected by my macbook, but i still cant connect wirelessly. the same goes when i tried my iphone. please help!

Is the status light green?
Your Airport device may be in Bridge Mode.
Airport Utility 6:
Open Airport Utility, select the Airport Express and click Edit. Navigate to the Network tab and change Router Mode to DHCP and NAT. Then click Update on the bottom right.
Airport Utility 5:
Open Airport Utility and click Manual Setup. Navigate to the Internet icon and change Connection Sharing to Share a Public IP Address. Then click Update on the bottom right.

WRT54G V8 Can't connect to web based setup page?

Earlier I reset my router and was able to use 192.168.1.1 to visit the web based setup page while trying to re-establish a home network now that I have a new computer using Windows 7 which can not use the easylink advisor. I was able to get on the page to update my SSID and WEP key. But when my wireless devices were still having problems connecting to the internet I tried to go back to the page and found that I can't get it to connect, though my desktop is able to connect to other internet sites just fine.
Does anyone know what i can be doing wrong? I am using Verizon DSL. I was able to ping the router and all tests showed that it was connected fine, yet I still cannot get on the setup page and my laptop still can't connect to the network. I have tried resetting the router again, and still nothing. And yes, I have gone through numerous power cycles. I also tried going though the network map on my computer, but the computer says it was unable to create a map for it even though at the time I had it listed as a Home network.
Message Edited by TaiShan on 01-03-2010 07:06 PM
Solved!
Go to Solution.

Wireless connections to 192.168.1.1 often fail. When accessing the router setup pages, always use a computer that is wired to the WRT54G.
If the above does not solve your problem, then here are my other tips for viewing the router setup pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
Some Zone Alarm users have reported that adding 192.168.1.1 to their list of "trusted" addresses fixed the problem. This trick might also work with other firewalls.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. The router should work, but you will need to setup your router again from scratch. If you saved a router configuration file, DO NOT use it.
If you still have trouble, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Message Edited by toomanydonuts on 01-03-2010 10:54 PM

Cant connect to the internet using my wrt54g

i bought the linksys wrt54g yesterday brought it home put in the setup disk and everythin was goin good until it came to step 10 and an error message came up saying: cant connect to the internet please shut off modem and turn it back on so tryed that still didnt work. so i found a thread when i searched this problem that said i had to bridge my westell 6100 modem to the router or somthin like that so i followed those steps and it still doesnt work can som1 help me please!?

Did you try to change the routers Ip address to 192.168.2.1?
I am not sure of that modem and not sure if it has a built in router ot not. Call your ISP and see if that modem is also a router running DHCP and everything else.
Richard Aichner (Ikester)

I cant get past the log in page

I download the Acobat XI pro. I cant get past the log in page. The response is "connect to the internet and try again". I am connected.

hello any one help me please tell me about flash player. http://www.shechoice.co.uk/ how can i instal flash player in window 8.

I have the WRT300N. When I go to the basic setup page an...

I have the WRT300N. When I go to the basic setup page and click on DHCP, none of the devices connected to the router show up. When I first set up the router they did. Does anyone know why I can't see them anymore?

Click refersh & see if all devices are there or not ...
Also you can check if all computers or devices areturned on or not ....

Was trying to install windows 8.1 but didn't install bootcamp first. Am in a loop. Keep coming back to the windows setup page. What to do?

Was trying to install windows 8.1 but didn't install bootcamp first. Am in a loop. Keep coming back to the windows setup page. What to do?

Please reset NVRAM - Startup key combinations for Intel-based Macs - Apple Support and OS X Mavericks: Reset your computer’s PRAM. You have Bootcamp settings in the nvram that are causing problems.

HT204400 no matter what i try, my apple tv says it cant connect to the network and it gives me error -3906. i have tried restart and reset, wifi, ethernet same error. all other devices work fine.

My apple TV has been working fine. Now it gives me error -3906 and says it cant connect to the network. it wont accept the password for my wifi. I have tried to restart and restore both the apple tv and my modem. still the same issue and same error message. any ideas?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT4993 Everytime i plug my phone into itunes it says it cant connect because the phone is locked well i restored my phone twice and set a new passcode the last time and it still wont work . I even deleted itunes and reinstalled it , it dosent work . HELP

Everytime i plug my phone into itunes it says it cant connect because the phone is locked well i restored my phone twice and set a new passcode the last time and it still wont work . I even deleted itunes and reinstalled it , it dosent work . HELP PLZ !!

I had the same issue. I tried everything unchecking / rechecking, formatting Iphone and restoring from backup etc etc.
In the end it was a simple issue which might of might not help you.
A number of months ago I relocated by Itunes folder to a NAS drive. It appears when I did the last I tunes update Itunes set the destination path of the Itunes media to the default location, the result was Itunes couldn't install music,apps, video until I set the correct destination path.
The bit that confused me was it was transferring some media. This was of course the media I had downloaded since the last Itunes update which had gone to the default location.
I hope that makes sense and is off some help.

I cant connect to the itunes store from my ipad

i cant connect to the itunes store in my ipad even the two movies that i rent before 4 days didnt download

Try logging out of your account on the iPad by tapping on your id in Settings > Store and then log back in and see if the two stores then work.

TS3297 Error message: 'Cant connect to the itunes store. An unknown error occured (-3212) please check you have an active internet connection and try again'. Help !

Can someone help me please ? I was using itunes (downloading albums etc) just half an hour ago. I had a pop up asking me if i'd like to download the latest version of itunes, which i accepted. When the update had finshed downloading, i then restarted my computer, as i usually would. Tried to re access the itunes store, and received the following error message: 'Cant connect to the itunes store. An unknown error occurred (-3212) please check you have an active internet connection and try again.
Needless to say, i have an active internet connection and cant see any reason why this would be happening, it has never happened before ?
Any help would be appreciated.

Do you have PeerBlock installed/ > TS3297 Error message: 'Cant connect to the itunes store.

I cannot connect to the add-ons page to get new ones

When I go to Tools, add-ons, I get the "What are add-ons?" and it tells me that when I connect to the internet the panel will feature many options.
I am online why can I not connect to the add-ons page?
Dan

There have been a number of issues with server problems over the last few days. Try to go to that Mozilla page again. The issues have been intermittent and could return at any time until a final resolution is found. This forum page has also been affected by the problem(s).
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''
Not related to your question, but...
You may need to update some plug-ins. Check your plug-ins and update as necessary:
*Plug-in check --> http://www.mozilla.org/en-US/plugincheck/
*Adobe Shockwave for Director Netscape plug-in: [https://support.mozilla.com/en-US/kb/Using%20the%20Shockwave%20plugin%20with%20Firefox#w_installing-shockwave Installing ('''''or Updating''''') the Shockwave plugin with Firefox]
*Adobe PDF Plug-In For Firefox and Netscape: [https://support.mozilla.com/en-US/kb/Using%20the%20Adobe%20Reader%20plugin%20with%20Firefox#w_installing-and-updating-adobe-reader Installing/Updating Adobe Reader in Firefox]
*'''''Shockwave Flash''''' (Adobe Flash or Flash): [https://support.mozilla.com/en-US/kb/Managing%20the%20Flash%20plugin#w_updating-flash Updating Flash in Firefox]
*'''''Next Generation Java Plug-in for Mozilla browsers''''': [https://support.mozilla.com/en-US/kb/Using%20the%20Java%20plugin%20with%20Firefox#w_installing-or-updating-java Installing or Updating Java in Firefox]

I cant connect to the itunes store and the support team didnt really help anyone facing this issue with ipad mini!!! I need help

I cant connect to the itunes store and the support team didnt really help anyone facing this issue with ipad mini!!! I need help

Here's the troubleshooter.
Can't connect to the iTunes Store

Hi My ipad 4 cant connect to the appstore its says Fatal Unable to process your request. Please Try again.

Hi My ipad 4 cant connect to the appstore its says Fatal Unable to process your request. Please Try again.

I had the same problem last night with my iPad Mini and then this morning on my iPhone. I did contact support this morning and they sent me a form to complete for the engineers. Support did tell me that I don't have to change my password (have done it already twice - frustrating!!).. Last night I was able to get my iPad to work but I had to sync it on my computer, after back up/sync was completed, the item that I was able to purchase on my iPhone yesterday finally was able to download onto my iPad. But wasn't able to get into the itune store online kept receiving the same error.

Customise the My Setup Page

Hi Guys,
Does anyone know if we can customise the My Setup Page.
We have created a new field, that we can see via the admin-user management page. But i want users to see this on their My Setup Page.
Any ideas??
Regards
Minesh

I am guessing you are specifically talking about the my profile page through my setup. We had the similar issue and have heard that this is a product enhacement. Will be available in the future

Cant connect to the WRE54G setup page.

Similar Messages

Maybe you are looking for