Cant get into bios after P965 NEO MB change..pls help

hi all, i just changed to the MSI P965 NEO, when i power up, all i get is the MSI start up utility asking me to press either "tab" or " del" , i pressed but nothing happens..
Can someone please help me out?..thanks

Quote from: accuwipe on 02-December-06, 23:34:15
alrite alrite...here it goes.
Model   RS-380-PMAR (Non-PFC (Regular))
RS-380-PMAP (Passive PFC)
Type   ATX Form Factor 12V V2.01
Input Voltage   90~140V / 180~265V (Selectable)
Input Current   8A @ 115Vac / 5A @ 230Vac
Input Frequency Range   47 ~ 63 Hz
Fan   Sleeve bearing 120mm fan
Power Good Signal   100 ~ 500 ms
Hold Up Time   > 17 ms
Efficiency   > 70% typically
MTBF   >100,000 hrs
Protection   OVP / OCP / OPP / Short Circuit Protection
Dimension   Standard ATX 150 x 140 x 86 (mm)
Operation Temperature   0~40?
Safety   Nemko / TUV / cUL / CE / BSMI / FCC
whats needed
< name brand >
+12v1 = ?
+12v2 = ?
+5v = ?
+3.3v = ?
if your psu doesnt have 12v 1&2 then list the +12v = ?
theres your problem, no futher testing till your power supply has been replaced!
24 to 30 amps on a SINGLE 12v rail power supply needed, and name brand / not generic.

Similar Messages

Unknown Processor Revison & Cant get into bios! RS482M4

Similair to problem to another post but have tried what was suggested.
This is my first attempt at an AMD system and I've hit a dead end on the first switch on...
AMD Athlon 64 3700+
MSI RS482M4 Motherboard
1GB RAM
WD 1600AB H/Drive
Sony CD-RW
When I power on I get the bios screen with the M/B details (RS482M4 A7019AMS V1.1) and processor details (AMD Athlon 64 Processor 3700+DRAM Clocking = 400 MHz).
It then goes a little further, initialises USB drivers, mememore HD and CDRom then states:
CMOS Settings Wrong
CMOS Date/Time Not Set
****Warning: Unknown Processor Revision ****
The processor installed on your system is of an unknown revision. Please contact your BIOS vendor for appropriate upadates.
Fatal Error ... System Halted.
I have tried resettng the CMOS but as I cant get into the BIOS I cant update it and feel like I've been going round in circles for the last 5 hours!
Any ideas?

Bios version is V1.1 and PC doesnt boot to anything - doesnt get beyond saying 'Unknown Processor Revision' to even allow you into the bios to try updating it.
I have also tried asking on the MSI online support but as yet with no reply. Its really annoying me as the motherboard has all the things I need and don't want to have to go and buy another one (have tried the CPU & memory in another machine and all worked fine).

Cant get into Bios, New board (K8T Neo-FIS2R)

I just put in a new board and cpu, everything seems to start up fine. BUT I press DEL to get into the bios settings and it tells me theres no bios installed. My HDs wont autodetect at the start so i havent gotten to windows yet, HD taken from old pc with winxp on it already.
Im totally lost here as what to do.
Can i just DL the newest bios drivers and flash?

Quote
no bios installed
...that's the Promise controller...you have to press Delete when you first power on, you're probably missing the timing because of the Core Cell screen...
...you don't want to flash the BIOS until you get a stable system...well, you could, but...

Cant get into BIOS via DEL key, screen goes blank on load RD240

Hello group, having an issue with a RD240 rackmount server attempting to bring it online for the first time. Currently in a one CPU configuration with one stick on RAM in the correct slot, using SAS. When the computer first boots prompting you to hit either DEL or TAB those keyboard commands are non-effective. Once it bypasses that screen it will move towards the LSI connfiguration utility. If you hit Ctrl +C it will say that the utility will become active after initialization. The screen then just goes blank. At that point I can hit Ctrl Alt Delete and it will reboot the server and then in the same mess again, Del is ignored, I can't boot off the CDROM, cleared the BIOS using the jumpers, nada. Any thoughts on this would be great, at this point I can't get in to configure and if I just let it boot always ends in a black screen. Checked the cables for the SAS and everything looks good across the board to me. Tried different RAM sticks, unplugging the SATA CDROM, etc. I can get into the Mgmt via the web and sensor show everything green across the board etc but something is borked. There is a LED screen on the mainboard with the number 78. I couldn't reference what that means. All drives I can hear click on, Cheetah 15k all around. Steady green light on bottom, top light out. Any input would be greatly appreciated!

Try pressing F1 at the Thinkserver Screen. When Setup Bios appears, you can exit out by pressing Esc. After the screen goes blank, press Ctrl+H to get the Web Bios screen which will allow you to configure your server. I hope that this will help.

HT201263 i cant restore my phone, I keep getting a message to turn off find my iphone, cant get into it b/c my daughter change the password and doesn't remember the password

help, i need to restore my phone, I keep getting an error to turn off find my iphone, I can't get into the phone b/c my daughter change the password and doesn't remember what she changed it to.

Remove an iOS device or Mac on which you can’t turn off Find My iPhone
If you can’t turn off Find My iPhone on the device, turn off the device so it goes offline, then remove it from Find My iPhone on iCloud.com.
Note:   If you have an iOS device, you can also remove your device by first erasing it—just follow the instructions below to remove a device you don’t have. You can later restore the device from an iCloud or iTunes backup.
                           Turn off the device.
                           Sign in to icloud.com/#find on another computer with your Apple ID (the one you use with iCloud).                                                      If you’re using another iCloud app, click the app’s name at the top of the iCloud.com window, then click Find My iPhone.
                           Click All Devices, select the offline device, then click Remove from Account. If you don’t see Remove from Account, click All Devices again, then click the Delete (x) button next to the device.                                                      If the device comes online again, it will reappear in Find My iPhone. To make sure your device doesn’t reappear, turn off Find My iPhone on the device (follow the instructions above to remove an iOS device or Mac), or if you have an iOS device, you can erase it, then remove it (follow the instructions below to remove an iOS device you no longer have).

MSI GE70 2OE Can't get into bios after update

Hello
I had some problems with the intel turbo boost not working properly so I updated my bios with the new version from 2013-09-03. After this update the intel turbo boost works fine but since I can't access my bios anymore. Does anyone have a solution?
Thanks

Problem solved. It seems that after the update you have less time to press delete to enter the bios.

Cant get c-media to work on fressh install pls help!!

Hello all,
I just reformatted my machine with win2k.
Everything has worked fine before no issues.
Since the reformat I am unable to load drivers for the onboard c-media sound chip.
It goes throught the install process and at the end says "invalid data type" for driver, install failed.
I have tried resetting bios via the jumper, no fix there.
It worked fine until I reformatted the PC and reinstalled win2000.
I reload the OS every 4 months or so and has never been an issue. Any help please ?

Just a few thoughts:
- make sure you have c-media enabled in your bios, I know it sounds stupid, but go to bios and check,
-if your system has recognized the card, try remove it from hardware list, and let the system find it again, and then install software,
-try newer version of c-media drivers,
-if nothing works and nobody comes up with a better idea you can reinstal wink2, maybe the next install will by a luckier one
Take care

I cant get into my ipod, it keeps saying connect to itunes, but it cant unlock my phone. Please help..

I cant get into my Ipod. It keeps saing "connect to Itunes" Please help..

Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
A
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
7. iOS - Unable to update or restore
Forgotten Restrictions Passcode Help
iPad,iPod,iPod Touch Recovery Mode
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
You can restore from a backup if you have one from BEFORE you set the restrictions passcode.
Also, see iTunes- Restoring iOS software.

I cant get into my itunes store

i cant get into my itune store

Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US

Cant get into the administrator

After a clean install of W2003 with SQL2005 Express and
CF7.02 with no errors. I get an error message "The page cannot be
displayed" when trying to open the Adminstrator for the first time.
I cant get into the Web Srv Cnfg Tool either.
here is where my adminstrator page points to. Sorry, I am
extremely new to all of this CF and IIS
http://127.0.0.1/CFIDE/administrator/index.cfm
After turning off the Friendly Http message filter this is
what gets displayed.
%1 is not a valid Win32 application

You could try the process noted in this older thread
http://www.adobe.com/cfusion/webforums/forum/messageview.cfm?catid=143&threadid=1160221
but I actually had no luck with it, so I resolved it by
simply installing a 32 bit version of Win2003/IIS6 on the 64 bit
hardware. I didn't have the luxury of time to keep playing with the
64 bit OS.
when the next version of CF comes out, it will hopefully
address both Vista and 64 bit and at that time I will consider
re-installing the 64 bit OS/IIS to take advantage of the superior
architecture and processing power.
you could try a search of Microsoft.com and see if they have
anything new suggested in relation to 32 bit extensions on a 64 bit
system, or even try Tek-tips.com for a similar search and inquiry
in the IIS forums.
Some day I may try it again, but at this time I will stick
with the 32 bit OS/IIS combo on the 64 bit HW

MOVED: [nForce] K7N2 D2-FSR cant get in window after manual setting

This topic has been moved to Overclockers & Modding Corner.
[nForce] K7N2 D2-FSR cant get in window after manual setting

I'm a bit of a noob at o/c so not sure I can give you sound advice.
pci is unlocked I think, though if use core centre then you can control it-I'm not using corecentre.
are you using priority 10 for prime 95 and In-place FFT's torture test? I believe that is most demanding. If you getting reboots then you're overclock is not stable, need to lower fsb and retest. Your psu is probably marginal as well so maybe that isn't quite strong enough to be pushed further. Can you try beefier one?
I don't know how far you can push vcore up; maybe one of our resident experts can advice.
I started out on this journey with exact problem you faced; I couldn't change High Performance mode from optimised to manual. I still haven't found a solution unless I enable DOT. I've tried bios b5, b6.1 and now trying b6.0, without success. O/S fails to load. Did you say b3 allowed you do to that and increase fsb in bios or was it change of memory? I'm thinking my expensive ram is not very flexible and doesn't suit the nforce 2 chipset. At moment with bios b60, high performance manual, memory to manual (2-2-2-11) and DOT enabled-private I passed memtest overnight. I'll try prime95 tonight if I have no issues tday.
Dave

[nForce] K7N2 D2-FSR cant get in window after manual setting

hi there,
i m a new guy here, not very good in english!!
before i send this, i had look some of the guide.
but cant find people with the same problem as me.
the problem is i cant get in window after set my High Perfomance Mode to MANUAL in cell menu.
nothing change just Optimized to Manual.
if access in, still will freeze after few second.
everything is fine with Optimized Mode, no error in Prime 95 for 9 hours.
hope can get some HELP from you all.
i also using core cell, will my setting in Bios appear same in core center???
example: 210 FSB in bios = 210 FSB in core center.
i hope to hear from you all soon.
10x.

I'm a bit of a noob at o/c so not sure I can give you sound advice.
pci is unlocked I think, though if use core centre then you can control it-I'm not using corecentre.
are you using priority 10 for prime 95 and In-place FFT's torture test? I believe that is most demanding. If you getting reboots then you're overclock is not stable, need to lower fsb and retest. Your psu is probably marginal as well so maybe that isn't quite strong enough to be pushed further. Can you try beefier one?
I don't know how far you can push vcore up; maybe one of our resident experts can advice.
I started out on this journey with exact problem you faced; I couldn't change High Performance mode from optimised to manual. I still haven't found a solution unless I enable DOT. I've tried bios b5, b6.1 and now trying b6.0, without success. O/S fails to load. Did you say b3 allowed you do to that and increase fsb in bios or was it change of memory? I'm thinking my expensive ram is not very flexible and doesn't suit the nforce 2 chipset. At moment with bios b60, high performance manual, memory to manual (2-2-2-11) and DOT enabled-private I passed memtest overnight. I'll try prime95 tonight if I have no issues tday.
Dave

Z68A-GD55 can't get into BIOS anymore

Just built new Z68 computer gradually over 3 days. Then loaded applications and everything worked great for 2 days. Decided it was done and time to change boot priority in BIOS. Couldn’t get into BIOS. Got splash screen but no further.
Found forum message recommending CMOS reset. Tried button, jumper, remove battery methods. Still can’t get into BIOS. Get BIOS Prompt ("...press DELETE"), but nothing after that except flashing cursor top left of screen. Back to barebones; same result. Screen messages before BIOS prompt: 98, 99, A3. Will not boot MS DOS (Win98 version) from USB drive (would before). I’d appreciate any suggestions. Thx.
Key build steps:
• Ran Memtest barebones 48 hrs.
• Added SSD (ACHI) and Installed Windows 7 Pro. SSD was new.
• Added, formatted HDD
• Enabled multi-monitor in BIOS; added Radeon HD6870; 2 monitors on Radeon, none on internal; installed Radeon drivers.
• Enabled Virtu in BIOS, d-mode; Installed Virtu
Not overclocked.

After replacing the PSU with a Corsair TX650M (650w, 3.3v30A, 5v30A, 12V54A), the barebones config could access the BIOS. Installed everything except boot SSD; still OK.
Before letting the computer boot back into Win7, I connected two old 19" LCD monitors (Microtek C997SD). For setup and testing, I had been using a 24" widescreen. But Win7 had never seen anything but the Microteks, which I intend to use with this computer. Tried to enter BIOS to verify settings were still correct for SSD. Got splash screen -- regular BIOS background, but no Icons (Green Power, Utilities, Overclocking, etc.). Computer locks: PS/2 keyboard (incl. Ctrl-Alt-Del) and USB mouse, do nothing.
Connected widescreen, verified BIOS OK. Shut down and reconnected Microteks, attempted boot into Win7, and all was OK. I just can't use a Microtek to access BIOS.
I hope MSI recognizes how valuable the volunteers here are. Your advice solved the problem at least a couple of days earlier than I would have done on my own. Thank you.

I have tried to change my User id which is an email address I no longer want to use. Now I am constantly getting requests from icloud and Apple ID for my password and cant get into my icloud account.

I have tried to change my User id which is an email address I no longer want to use. Now I am constantly getting requests from icloud and Apple ID for my password and cant get into my icloud account.

To change the iCloud ID you have to go to Settings>iCloud, tap Delete Account, provide the password for the old ID when prompted to turn off Find My iPhone, then sign back in with the ID you wish to use. If you don't know the password for your old ID, or if it isn't accepted, go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. Then edit the name of the account to change it back to your old email address. You can now use your current password to turn off Find My iPhone on your device, even though it prompts you for the password for your old account ID. Then save any photo stream photos that you wish to keep to your camera roll. When finished go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was. Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

How to get into BIOS in Windows 8

my question is this will the same fan control software that was on windows seven 64 bit lenova work with windows 8 and 8.1 just wondering if i have to uninstall before i upgrade or will it be compatable with 8 and 8.1 upgrade hope someone can steer me in the right direction here it would be appreciated-thanks

Hi,
follow the links below:
http://forums.lenovo.com/t5/Windows-8-and-8-1-Knowledge-Base/How-to-get-into-BIOS-in-Windows-8/ta-p/...
http://support.lenovo.com/en_US/detail.page?DocID=HT076607
win8 should be installed on the big HDD.
If you have enough computing skills Win8.1 Update could be installed on the small SSD using the new feature - WimBOOT.
x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
Do it well, worse becomes itself
Русскоязычное Сообщество English Community Deutsche Community Comunidad en Español

Cant get into bios after P965 NEO MB change..pls help

Similar Messages

Maybe you are looking for