Cant print desktop -23 error

I have tried everything, updated drivers for our printer (ethernet network) Run diskwarrior over the hardrive and diskdoctor, the lot? This applies for all applications (as this is how it started trying to print from quark 4.1).
I have the a printer utility which i started up and printed a test sheet to the printer so the printer is on the network and is fine.
Please help i'm at a loose end
Thanks

Hi, lister -
Welcome to Apple's Discussions.
This may apply - http://discussions.apple.com/thread.jspa?messageID=607636&

Similar Messages

  • Acrobat 8.1.2 cant print pdf no error

    My husband has an emachine desktop with HP Deskjet D4160, 512 RAM and Adobe reader 8.1.2 ... I have a Sony Vio desktop, 1.5 gig RAM, a second printer same model, and the Adobe reader 8.1.2. The 2 computers are not networked. Both of us are using windows XP operating system. We both have the same problem since we installed Adobe Reader 8.1.2, we are unable to print any pdf file. We do not get any error messages.
    After we select print, you can hear the printer click a couple times as though it was getting ready to print, then nothing. There is no printer icon in the tool bar showing that the printer has anything pending. If you open up the printer it also shows Printer is ready with no pending documents. Again, it does not show any errors or warnings.
    I have searched the forum and knowledgebase, found some suggestions where people had an error message to report. I tried what was suggested there including changing going into "Comments and Forms" ... Document and Markup, then changing that to just Document. Didn't change anything.
    This is getting pretty frustrating have both computers with the same problem and have PDF documents that need to be printed. I sure would appreciate some ideas on how to correct the problem. OH .. I also checked for updates from Adobe and we are current, both computers have Service Pack 2 and are current with updates. Windows XP is also updated several times a week with any current patches or updates.

    You may need to check the Reader forum. I have no idea why the problem exists, but it may be that it is something particular to Reader and not Acrobat. The link for the Reader forum is at the top of this forum.

  • HP LaserJet Pro M1536dnf Multifunction Printer (unable to add print driver hpfax1, error code 87)

    Hi, my printer HP LaserJet Pro M1536dnf Mfp, suddenly didnt work so i remove the printer, and downloaded a new driver  http://support.hp.com/us-en/drivers/selfservice/HP-LaserJet-Pro-M1536-Multifunction-Printer-series/3974271/model/3974278#Z7_3054ICK0KGTE30AQO5O3KA30R1 once dowloaded, i run it and uninstall the printer, restart my pc, and proceed to installing. but in the process of installing a error occurr, saying that "Unable to add printer, error code 87", and that " HP Toolbox FX has encountered an error and can not recover. once i click ok. it tells me to restart my pc and reinstall it again. i did it for 8x, and still with the same error. please help really need a help right now. as my boss is going to kill me

    Hey , Welcome to the HP Support Forums!
    I understand that you're getting the error 'Unable to add print driver hpfax1, error code 87' when installing your HP LaserJet Pro M1536dnf Multifunction Printer on your Windows 7 computer. I would like to assist you today with resolving this install issue. Thank you for including all of the troubleshooting steps that you have completed prior to reaching out for support. At this time I am going to walk you through some additional software and driver troubleshooting steps. Please follow all of the steps below.  If you're using your HP Laserjet through a USB Cable connection, please disconnect that cable now.  Step one: Remove Driver: 1. Click on your Start menu 2. Select Control Panel 3. Select Programs and Features 4. When Programs and Features opens a list of programs installed on your computer will populate. Click on the 'Installed ON' tab at the top to change the date so the recently installed items show at the top. This will make it easier to manually locate the three HP Laserjet items you need to uninstall.  5. Next, look for the HP LJ M1530 MFP Series HP Scan, HPLaserJetHelp_LearnCenter, and HP LaserJet Professional M1530 MFP Series. If you see any 3 of these, or all 3 of these items, please click on them and select Uninstall.   Once you have confirmed that those three items have been uninstalled, please close Programs and Features and proceed to the next step.   Step 2: Clear Temp Files:  Click on your Start menuIn the 'search programs and files' box located right above Start after you click on it, type %temp% and hit enter on your keyboardWhen the Temp folder opens, select Ctrl + A at the same time on your keyboard. Everything in this folder will now highlight.Select the 'delete' button on your keyboard. The Temp folder contains temporary internet files. No actual files or folders on your computer will be affected by deleting the Temp files. Should a Temp file still be used than you will automatically get the pop up to 'skip' that item.Close the Temp folder once it is emptiedRight click the Recycling Bin on your desktop and select Empty Recycling BinPlease proceed to the next step.    Step 3: Download Installer Package:  Please click here to download the Full Feature Installer package. Once the download is complete, click on the download to allow it to 'Run'An extraction should now automatically occur. Once the extraction is complete an installer window will open. Please close the installation window.  You do not want to run the installation at this time.   Step 4: Run Scrubber:  To ensure that no trace of the HP Software and Driver package remain on your computer, I am going to have you run a Scrubber built into the installer package for your printer.  Click on your Start menuIn the 'search programs and files' box located right above Start after you click on it, type %temp% and hit enter on your keyboardWhen the Temp folder opens locate the 7z folder. Click on this folder to open it. This is the HP Laserjet Installer Click on the Utilities folder under the 7z folderDouble left click on Scrubber. It is an application which should launch the HP Uninstaller. Please follow the onscreen prompts to complete the uninstaller.    Once the uninstall has completed please proceed to the next step. Be sure to Restart your computer if the uninstall process prompts you to.    Step 5: Check Print Server Properties:  Click on your Start menuClick on Devices and PrintersIn the Devices and Printers window look for your HP Laserjet. If you see it listed please right click on it and choose 'Delete' or 'Remove Device'. Next, click on any device listed under 'Printers and Faxes' once just to highlight itClick Print Server Properties at the top of the windowClick on the Drivers tabLook for your HP Laserjet driver. If you see it click on it and click Remove at the bottomClick Remove Driver OnlySelect OKSelect Apply and OK on the Print Server Properties windowClose Devices and Printers. Please proceed to the next step.  Step 6: Run Disk Cleanup Utility: Click on your Start menuSelect All ProgramsSelect AccessoriesSelect System ToolsSelect Disk Cleanup Run a Disk Cleanup on the C DriveWhen prompted, check Downloaded Program files, Temporary Internet Files, Recycle Bin, Temporary Files, and Thumbnails Once the Disk Cleanup is complete, please proceed to the next step.    Step 7: Run CCLeaner:  To ensure that there are no malicious files on your computer or Registry conflicts on your computer I am going to have you run a CCLeaner before we install your printer. Please click here to download the CCLeaner Tool. Once the website opens select the link at the top for 'Free Download'. Once the download is complete please complete the Scan. Should multiple malicious files be found you may need to run the Scan multiple times to remove all malicious files. Once your system comes back as clean, please proceed to the last step.    Step 8: Install Device:  Please click here to download the Full Feature Installer package for your HP LaserjetOnce the download is complete please allow the download to RunPlease follow the onscreen prompts to install your HP LaserjetIf using a USB Cable connection please do not plug in the USB Cable until the installer window prompts you to  Once the installation has completed successfully please test your machine to confirm that everything is functioning properly. Please respond to this post with the result of your troubleshooting. I look forward to hearing from you. Good luck!

  • Cant printing of a logo in a script.

    hi all,
         i have printed everyting in a script except a logo in the window assigned to that .
    instead it is printing its logoname in that.
    i went to se38 and typed medruck and i copied everything in that .but all of it cant print.
    so , tell me how to print that .

    HI  jyothsna,
    we are using ECC 6.0 version..
    when i cpoy "rvorder 01"  to "zrvorder01"
    every thing is copied into my sscript with eng lang.
    after uploading the logo into se78  i', trying to create a graph window in script.
    it is giving no errors but..
    1.creating elements is ged out..
    2. when i 'm trying to create a graph  from layout it is not giving options to create
    her i want to create a seperate window for company logo...
    thanks  in advance...

  • Cant print document after lion installation with my fuji xerox printer

    i cant print after lion installation with my fuji xerox c1110b printer, even after i remove and reinstall the driver.
    in the print window  under status indicate error,
    for other program even the print button is not working,  need help
    thanks

    As a temporary fix until the new driver, you can still use Generic PCL Laser printer selection to print black and white on Fuji Xerox C1110B.  When adding the new driver, select Options & Supplies.  When the new window rolss down, click on the middle Driver button.  Then select Generic PCL Printer, and OK.
    Maybe there is another substitute driver we can use to print in color as well until Fuji Xerox gets its act together?

  • Cant print from internet on my d1660.

    cant print from internet without restarting the spooler. and have lots of trouble then. usually prints ok from desktop office.

    Have you ever had another printer installed on this computer? If so, it is possible that the wrong printer is selected in some of your software settings.
    007OHMSS
    I was a support engineer for HP.
    If the advice resolved the situation, please mark it as a solution. Thank you.

  • Hour glass wont go away on display, so cant print or scan.. Please advise.

    Hour glass wont go away on display, so cant print or scan.. Please advise.

    traumax,
    Try downloading and running the print and scan doctor located here:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
    It can fix a lot on its own and if not give a better idea of what is going on and would you mind clarifying where we see the hour glass - on the printer or the desktop? 
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • 8600 printer in an error state message -- will print from Mac but not from my pc

    We have two computers wirelessly connected to my hp 8600. The Mac prints fine, but recently I started receiving error messages when I try to print from my desktop PC: "Printer in an error state"  I have tried unplugging from the wall, turning on and off, rebooting, so far nothing helping. 

    Samsdad wrote:
    But I had done that when I first set up my printer. And it worked up until a couple days ago. Don't know what changed.
    Then try look at these tips to see if these can figure the problem?
    Wireless printing center
    Common fixes for wireless connectivity issues
    I Can't Find the WEP or WPA Key or Password for My Wireless Network
    HP Wireless printing center
    I am a Volunteer to help others on here-not a HP employee.
    Replies aren't online 24/7 because of Time Zone differences.
    Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

  • Cant print on tcode f883

    hi
    anybody knows why I cant print from the tcode f883 after displaying a PRINT REQUEST NUMBER?
    in other clients, its possible but in development its not

    icutwo222 wrote:
    Missing xml viewer file on my computer....need assistance to recover file.
    Hi,
    It came with Windows. What is an error when you try to open file ?
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Cant open itunes. get error message 7 followed by error message windows error 127.     i have redownloaded new updates with luck.   window xp

    cant open itunes. get error message 7 followed by error message windows error 127.     i have redownloaded new updates with luck.   window xp

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it, which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    tt2

  • I installed a new printer and now Photoshop Elements tells me I can't print.  The error message is "The saved printer information is not compatible with this version of Photoshop Elements, or the saved printer is no longer available.  You will need to che

    I installed a new printer and now Photoshop Elements tells me I can't print.  The error message is "The saved printer information is not compatible with this version of Photoshop Elements, or the saved printer is no longer available.  You will need to check your printer settings before printing."  I have uninstalled and re-installed Photoshop Elements, checked my printer settings and still I can't print a photo.

    Hi ,
    Please update to PSE 13.1
    13.1 has solved this problem.
    Refer to this link.
    Photoshop Elements Help | Printer errors with Photoshop Elements 13

  • Can't install the software for the Brother MFC-9440CN because it is not currently available from the Software Update server....how do I get the driver then..it ised to work in my old mac..but cant print to it in my new unit

    Can't install the software for the Brother MFC-9440CN because it is not currently available from the Software Update server....how do I get the driver then..it ised to work in my old mac..but cant print to it in my new unit

    Download the Brother Mountain Lion drivers here.

  • Print a custom Error message in the XML bursting program's log file...

    Hi,
    I having this requirement, where i need to print a custom error message in the xml bursting program's log file.
    Actually i am having a report where i create invoices and then those invoices are emailed to the respective customers, now say if a customer has three contacts and there is only two valid email id's so what happens is bursting will be successful for two contacts whereas the third contact dosen't get any emails. when this happens i need to log a message in the bursting programs log file stating a custom message.
    Two things i want to know..
    1- Whether is it possible to write into the xml bursting programs log file
    2- If yes, then how..
    note: it ll be greatly appreciated if the answer is elaborated.
    thanks,
    Ragul

    Hi,
    I having this requirement, where i need to print a custom error message in the xml bursting program's log file.
    Actually i am having a report where i create invoices and then those invoices are emailed to the respective customers, now say if a customer has three contacts and there is only two valid email id's so what happens is bursting will be successful for two contacts whereas the third contact dosen't get any emails. when this happens i need to log a message in the bursting programs log file stating a custom message.
    Two things i want to know..
    1- Whether is it possible to write into the xml bursting programs log file
    2- If yes, then how..
    note: it ll be greatly appreciated if the answer is elaborated.
    thanks,
    Ragul

  • How to print only fatal error in log file in tomcat4.1

    Hi all ,i m using tomcat4.1
    1> i want to print only fatal error in log file ,but it print all thing in log file ,how i can avoid it(because i think this process is consuming my resource)
    assume below ip address is corect:
    this is exact printing in my log file
    .12.2.3.3  - - [24/Oct/2007:00:00:00 5050] "GET /menu/ir.jsp HTTP/1.1" 200 2828
    12.2.3.3  - - [24/Oct/2007:00:00:00 5050] "GET /menu/bottomAdv.jsp HTTP/1.1" 200 528
    12.2.3.3  - - [24/Oct/2007:00:00:02 5050] "GET /menu/alerts.jsp HTTP/1.1" 200 323
    12.2.3.3  - - [24/Oct/2007:00:00:02 5050] "GET /alerts/createAlertShow.jsp HTTP/1.1" 200 26140
    123.2.3. - - [24/Oct/2007:00:00:05 5050] "GET /menu/getsensex.jsp HTTP/1.1" 200 642
    12.2.3.3 - - [24/Oct/2007:00:00:05 5050] "GET /menu/latestRecommendation.jsp HTTP/1.1" 200 5210
    12.2.3.3 - - [24/Oct/2007:00:00:05 5050] "GET /portfolio/watchlist/displayWatchlistItemsShow.jsp?watchlistId=20070509013642953_1&watchlistName=First&refreshRate=900&flag=1 HTTP/1.1" 500 7257
    12.2.3.3  - - [24/Oct/2007:00:00:05 5050] "GET /menu/iwealthNewsScroller.jsp HTTP/1.1" 200 2828
    112.23.3  - - [24/Oct/2007:00:00:06 5050] "GET /menu/alerts.jsp HTTP/1.1" 200 323
    112.23.3 - - [24/Oct/2007:00:00:06 5050] "GET /menu/bottomAdv.jsp HTTP/1.1" 200 528
    12.2.3.3  - - [24/Oct/2007:00:00:07 5050] "GET /menu/alerts.jsp HTTP/1.0" 200 323
    12.2.3.3 - - [24/Oct/2007:00:00:09 5050] "POST /Transaction/equity/modifyConfirmShow.jsp?DelId=0 HTTP/1.1" 200 28661
    12.2.3.3  - - [24/Oct/2007:00:00:09 5050] "GET /menu/getsensex.jsp HTTP/1.1" 200 6422>what will happen if i change timestamp="false" and what is the significance of verbosity="1" or "2" or "3" ,or "4" and what happen if i change debug="1" or other in below code
    <Logger className="org.apache.catalina.logger.FileLogger" debug="0" directory="logs" prefix="www.xyz_log." suffix=".txt" timestamp="true" verbosity="4"/>Edited by: Deepak23 on Oct 24, 2007 10:41 PM
    Edited by: Deepak23 on Oct 24, 2007 11:16 PM

    One of my standard answers (which will explain the use of Directory Objects)...
    The UTL_FILE_DIR parameter has been deprecated by oracle in favour of direcory objects because of it's security problems.
    The correct thing to do is to create a directory object e.g.:
    CREATE OR REPLACE DIRECTORY mydir AS 'c:\myfiles';Note: This does not create the directory on the file system. You have to do that yourself and ensure that oracle has permission to read/write to that file system directory.
    Then, grant permission to the users who require access e.g....
    GRANT READ,WRITE ON DIRECTORY mydir TO myuser;Then use that directory object inside your FOPEN statement e.g.
    fh := UTL_FILE.FOPEN('MYDIR', 'myfile.txt', 'r');Note: You MUST specify the directory object name in quotes and in UPPER case for this to work as it is a string that is referring to a database object name which will have been stored in uppercase by default.

  • When I try to print from web page I get "printer not activated - error code 30", but I can copy text into Word document & printer works.

    I am unable to print anything from an internet web page. I continually get "printer not activated, error code- 30" followed by "An unknown error occurred while printing". I can copy the material from the web page, place into a Word document and then print. This just started yesterday and I have no idea why. Would appreciate your advice!

    See this:
    [http://kb.mozillazine.org/Problems_printing_web_pages#Prints_to_a_small_portion_of_the_page]

Maybe you are looking for