Captive Portal spinner is ultra small

Please refer to attachment. Not annoying stuff but a little of strange there.

Hmm...pretty interesting. What redirection mode did you use for m0n0wall? (http or dns) Have you tried disabling the NAT on the router as well as unchecking the block anonymous internet requests on the security tab?
I have a similar setup on a T1----media converter----WRT54G setup. Basically, the router was able to get public wan ip addresses on the status page. So do the computers behind it (wired and wireless) but they aren't online. We pinged the three dns numbers on the router, only 1 replied. Now, the ISP has Cisco all-access installed on the converter (quite similar to captive portal) and it shows up on every computer when we try to go online. We open up the browser, it prompts for the authentication. We fill-in the details but still it doesn't go online. Bottom line was we cloned the mac of the main computer and they didn't need to authenticate...but then again it defeats the purpose of the software.
Also, the router was set as a DHCP server with NAT enabled. I'm thinking that the router's firewall still blocks your computers even when it's already set as a switch. Try to disable the NAT and see if it works.

Similar Messages

  • ISE captive portal timeouts and radio policy

    Hello!
    I have two questions.
    First, have some of you guys worked with the captive portal in ISE (guestportal)?
    I have set up a new wireless network for a customer and they want to use the guest portal for som users.
    The problem that I am expering is that on a particular site with many small buildings user complains that they have to reauthenticate using the webportal when moving between the buildnings.
    I have tired extending the idle user timeout on that particular wlan in the cisco 5508, but I still having this problem.
    I would actually like if the user login via the guestportal at the beginning of the work day and after say 4-5 hours they have to reautencitcate.
    And if they loose network connectivity (moving between buildings, iphone/andriod shutting down wifi adapter, etc) they shuld be fine connecting again because they have aldready authecnticated once during the last 4-5 hours.
    Is this possible via the ISE?
    My second question deals with 2.4 and 5 Ghz band.
    I use AP groups on each of my distribution areas. All groups have the same SSID but diffrenet egress interfaces (interfaces groups).
    And in some of these I want to save the 5 GHz band for voice over wlan and in others i would like to use both bands.
    Do I have to create diffrent wlan profiles with diffrent radio policys and same SSID or could I do this in the AP group settings using RF-profiles?
    Hope for some help!
    //Simon

    Your first answer  is there is no such option in ISE till now there you can specify the login time fix for a client. If the client disconnect from the network and reconnect again, it require re-authentication Every time.
    2nd : You can use the AP group settings using RF-profiles to achieve this task.1st: There is no such option in ISE till now there you can specify the login time fix for a client. If the client disconnect from the network and reconnect again, it require re-authentication Every time.
    your seconde answer : You can use the AP group settings using RF-profiles to achieve this task.

  • Captive portals not triggering on Mavericks

    I frequent locations that require a "I accept your policy, please connect me to wi-fi" screens upon connection, before allowing traffic to leave the local network. Prior to Mavericks, a small browser window would display, prompting me to accept and connect. On Mavericks, I have yet to see one of these.
    Here are some pertinent log entries from Console.app:
    0/31/13 8:31:26.665 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Inactive
    10/31/13 8:32:40.289 AM UserEventAgent[11]: Captive: [CNInfoNetworkActive:1655] en0: SSID 'attwifi' not making interface primary (no cache entry)
    10/31/13 8:32:40.289 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Evaluating
    10/31/13 8:32:40.294 AM UserEventAgent[11]: Captive: en0: Probing 'attwifi'
    10/31/13 8:32:40.316 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:40.492 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:40.657 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:40.842 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:41.126 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:41.514 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:41.927 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:42.520 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:43.201 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:43.945 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:44.827 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 8:32:44.827 AM UserEventAgent[11]: Captive: [wispr_detect_http_done:269] Network Error: Failed to retry probe. Giving up after retrying 10 times
    10/31/13 8:32:44.827 AM UserEventAgent[11]: Captive: [CaptiveHandleRedirect:1653] Unknown result value: 8, assuming online
    10/31/13 8:32:44.828 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Authenticated
    10/31/13 10:13:46.955 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Inactive
    10/31/13 10:14:02.663 AM UserEventAgent[11]: Captive: [CNInfoNetworkActive:1655] en0: SSID 'PANERA' not making interface primary (no cache entry)
    10/31/13 10:14:02.663 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Evaluating
    10/31/13 10:14:02.668 AM UserEventAgent[11]: Captive: en0: Probing 'PANERA'
    10/31/13 10:14:02.829 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:03.005 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:03.187 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:03.369 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:03.653 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:04.039 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:04.513 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:05.096 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:05.766 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:06.549 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:07.421 AM UserEventAgent[11]: Captive: [async_http_read_stream:387] kCFStreamEventErrorOccurred NSPOSIXErrorDomain/51: The operation couldn’t be completed. Network is unreachable
    10/31/13 10:14:07.421 AM UserEventAgent[11]: Captive: [wispr_detect_http_done:269] Network Error: Failed to retry probe. Giving up after retrying 10 times
    10/31/13 10:14:07.421 AM UserEventAgent[11]: Captive: [CaptiveHandleRedirect:1653] Unknown result value: 8, assuming online
    10/31/13 10:14:07.421 AM UserEventAgent[11]: Captive: CNPluginHandler en0: Authenticated
    Anyone having similar issues, or can point me towards a solution?

    I was able to manually trigger the Captive Portal Assistant and work around the issue. Open up Terminal.app and type:
    open /System/Library/CoreServices/Captive\ Network\ Assistant.app
    After that, I saw the window I was expecting and I was able to click the "I agree" button, and afterwards my Internet was working as expected.

  • Bug in wifi/wireless connection with captive portal in UK/London ?

    With my macbook pro (10.6.4) & iphone (iOS 4), I do not manage to have an easy connect on free wifi captive portals in London. They all are new connections (unknown networks before).
    * dhcpd lease seems to be instable. I can get wifi connection (with good wifi signal strength) but most of the time get a "non-allocated" lease like 169.254.57.x/24 without any router/dns. A few rare times, the dhcp server give a me a complete ip connection.
    * in the rare case where IP connection could established, I was not redirected to the captive portal. I had to manually enter its address (in my case <IP>:8000, you need to guess) and even after authentication, I can't browse the Internet. In one of my test, I managed to resolve dns entry but can't browse the web.
    I tried during an hour and I couldn't make it on work on my Macbook. work a small time with the iPhone.
    tested in McDo free wifi and Airbox Public Wifi of EasyHotel (Airbox system). also have problem with "Wifi Zone - The Cloud".
    ok in Starbucks and in St Pancras Free Wifi.
    Found these threads which could be related but no real solutions:
    http://discussions.apple.com/thread.jspa?messageID=11875166&#11875166
    This is probably the router's fault but I can't check this.

    Hmm...pretty interesting. What redirection mode did you use for m0n0wall? (http or dns) Have you tried disabling the NAT on the router as well as unchecking the block anonymous internet requests on the security tab?
    I have a similar setup on a T1----media converter----WRT54G setup. Basically, the router was able to get public wan ip addresses on the status page. So do the computers behind it (wired and wireless) but they aren't online. We pinged the three dns numbers on the router, only 1 replied. Now, the ISP has Cisco all-access installed on the converter (quite similar to captive portal) and it shows up on every computer when we try to go online. We open up the browser, it prompts for the authentication. We fill-in the details but still it doesn't go online. Bottom line was we cloned the mac of the main computer and they didn't need to authenticate...but then again it defeats the purpose of the software.
    Also, the router was set as a DHCP server with NAT enabled. I'm thinking that the router's firewall still blocks your computers even when it's already set as a switch. Try to disable the NAT and see if it works.

  • Dual Band Concurrent AP with captive portal?

    Hi, Was looking at purchasing WAP321 however after looking at the spec's I see it has not got concurrent dual band (2.45Ghz/5Ghz) is there any simular access points with dual band and captive portal?
    Thank You

    Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
    There is not an access point in the Small Business collection that has dual radio capability. The AP541 and WAP321 has dual band 2.4 and 5 ghz, but only one band at a time because they only have a single radio.
    To find something with dual band, dual radio that can do 2.4 and 5 ghz at the same time you will have to look at Cisco Enterprise, AP1262N or 1142N for example.
    Hope this helps.
    Thanks
    Eric Moyers
    Cisco Network Advanced Support Engineer
    SBSC Wireless and Surveillance SME
    CCNA, CCNA-Wireless
    1-866-606-1866
    *Please rate Post so other will know when answer have been found.

  • ISA500 Series - Captive Portal

    Hi,
    Is there anyone who have the Captive Portal working properly with a FQDN approved certificate ? I have already installed a approved certifiacte but each time the client is redirected to the Captive Portal default ip address on the ISA router used. Is there any option where it will redirect to a FQDN example the host and domain name of the router - insted of the routers ip adress ?
    Regards
    Tonni

    Hi Tonni, thank you for using our forum, my name is Luis I am part of the Small business Support community. I apologize for your inconvenience, in this case I found an article and I thought that could be helpful in order to configure your Captive Portal.
    http://www6.nohold.net/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=3458
    I hope you find this answer useful
    Greetings,
    Luis Arias.
    Cisco Network Support Engineer.

  • WAP-321, Captive Portal and Wi-FI repeaters

    Hi,
    So I am currently deploying a Wi-Fi Network based around Cisco WAP-321. I use the CP function with a Radius server to authentify my users. So far so good, when a user connect to one of the AP and uses his credentials, he can login and access Internet without any trouble. But I also use some Wi-Fi repeaters (Netgear WN-1000RP) to extend the range of my wireless network in places I can't install an AP. The repeaters effectively extends the range of my network, and I can connect on them without any trouble when the CP is turned off. However, when I turn on the CP, I access the login web page and enter my credentials, but no matter what, I can't login while connected on the repeater. After some research, it looks like I have to manually enter the MAC address in the MAC trough list of the AP. Except such a feature doesn't seem to exist on the WAP-321. I have tried using WDS bridge and Workgroup bridge, but without success, since I think it's only compatible with WAP-321 and WAP-121 devices.
    So I am kind of running out of ideas to make this work, and I would be very grateful if someone could help me out.
    Thanks in advance, do not hesitate to ask me for more informations if needed.

    My name Eric Moyers. I am an Engineer in the Small Business Support Center.
    I am sorry to hear that you are experiencing this issue. 
    While what I am fixing to share is not in any way a great solution, It can be utilized as a workaround.
    With the WAP321, after trying a few different scenarios that didn’t work. I simply created two vlans, leave the Untagged vlan as main vlan and changed the Management vlan to the second. I then attached the guest SSID to the Management VLAN. This allowed me to authenticate to my guest captive portal and get an IP and get out to the internet. The Main SSID still worked normally.
    Now for some caveats:
    Problem: If a wireless client knows the IP of the WAP and the username and password they could get into the WAP.
    Solution: Setup Management Access Control to an IP outside the DHCP scope for that VLAN and have a Strong Password.
    Problem: Management of the WAP321 can only be from an IP on the Management VLAN. (In my case 2)
    Solution: Setup Management Access Control to an IP outside the DHCP scope for that VLAN and have a Strong Password.
    Not the very best solution, but the only workaround I can come up with for now.
    Eric Moyers
    .:|:.:|:. CISCO | Cisco Presales Technical Support | Wireless Subject Matter Expert
    Please rate helpful Posts and Let others know when your Question has been answered.

  • Automatic disconnection from AP when timed out (session or authentication) from captive portal

    Captive portal implementation permits/blocks web traffic. When a user is timed out (authentication & session) it still occupies a channel as seen in the clients list. How can we disconnect a host that is timed out?

    There is NO Failed Authenticated list.These are the only available tabs in the lapac1200Captive Portal Global Configuration  Portal Profiles  Local User  Local Group  Web Customization  Profile Association  Client Information

  • Anyconnect 3.1 Captive Portal False Alert Stops Users Connecting.

    Hi All,
    I am having problems with a customer's ASA 5505 with Anyconnect 3.1 - it is generating captive portal false-alerts which are stopping users from connecting.
    This issue began when I upgraded from Anyconnect 2.4 to 3.1, and it appears like this: A user downloads and installs the Anyconnect client and is able to connect fine, to begin with. However, once they reboot their computer and try to reconnect, the VPN session will not come up and they receive the error message below.
    "The service provider in your current location is restricting access to the internet. You need to log on with the service provider before you can establish a VPN session. You can try this by visiting any website with your browser."
    Reading other posts, it seems this message appears when a captive portal is restricting internet access. It must be a false alert in this case as there is nothing of the sort here. Apparently, Anyconnect 3.1 can generate a false alert like so if the name of the firewall's SSL certificate doesn't match the CName listed on the Client Profile. I've set this up to match, to no avail.
    Although users can connect by reauthenticating through the SSL VPN login web page, I am stumped as to how to get rid of this captive portal error that pops up when they try to use the Anyconnect client.
    Any advice would be appreciated, just let me know what extra details to post if needed.
    Many thanks,
    Josh Campbell

    Hi Joshua,
    The below information could be located at
    www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect31/administration/guide/ac03vpn.html
    False Captive Portal Detection
    AnyConnect can falsely assume it is in a captive portal in the following situations.
    •If AnyConnect attempts to contact an ASA with a certificate containing an incorrect server name (CN), then the AnyConnect client will think it is in a "captive portal" environment.
    To prevent this, make sure the ASA certificate is properly configured. The CN value in the certificate must match the name of the ASA server in the VPN client profile.
    •If there is another device on the network before the ASA, and that device responds to the client's attempt to contact an ASA by blocking HTTPS access to the ASA, then the AnyConnect client will think it is in a "captive portal" environment. This situation can occur when a user is on an internal network, and connects through a firewall to connect to the ASA.
    If you need to restrict access to the ASA from inside the corporation, configure your firewall such that HTTP and HTTPS traffic  to the ASA's address does not return an HTTP status. HTTP/HTTPS access to the ASA should either be allowed or completely  blocked (also known as black-holed) to ensure that HTTP/HTTPS requests sent
    There is also a bug filed for this. Just for your reference,
    CSCud17825 - Anyconnect captive portal
    Regards,
    Srikanth K S.

  • Laptop no longer loads Captive Portal following Windows 8.1 upgrade

    Since upgrading to Win 8.1 from Win 8, I no longer see a captive portal displayed whenever I try to connect to a wireless network that requires additional login information.  Some WiFi networks require you to click their Terms and Conditions box
    or add some additional logon information and they splash up a Captive Portal screen to allow you to enter the information.  Without entering this information I receive an IP address for my wireless adapter ok, but end up with a "Limited Internet"
    connection.  Which means I cannot connect to the Internet at all.  This exact same problem has happened to two colleagues of mine that recently upgraded to Windows 8.1 on their laptops.  Any help will be much appreciated.

    Hello Grantlsmith,
    Do you receive any error message when you connect to a wireless network that requires additional login information?
    Or you just connect to the Wi-Fi with limited Internet, and nothing pop up?
    Please take the following steps for troubleshooting:
    1. Please provide the result of the command ipconfig –all
    2. Ping the IP address of URL and check if we can contact.
    3. Type in the URL that can use in Windows 8 and check if we can open the Captive Portal
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • Infoblox Captive Portal will not pass the "Accept" screen on Iphone or ipad 6.1.2

    I am learning there is an issue with 6.1.2 with Captive Portal services where the latest IOS release will not progress beyond the terms and conditions. The next step in the authentricatoin process is certificate check so it would appear Apple has altered the process?
    We have a lot of users complaining now but only 6.1.2 is affected. I have checked previous version on other devices and there is no issue.
    Thanks
    Ken

    Anyone? C'mom, I know some of you techie type folks know how to fix this!

  • Captive Portal not working correctly

    I've seen issues with our wireless systems on WebOS devices running the latest software. If I try and use the HP Tablets with a captive portal log on. I can put in my creds to login hit submit, but nothing happens. Reviewing a sniff trace of the transaction I see "you have reached this page because you browser does not support standard http redirection commands"
    My concern is most people are probably hitting the same issue based on what I have read thus far.

    I am also having trouble with a captive portal on my school's (UC Berkeley) wifi network.
    I can get to the login page, and enter my credentials, but after hitting "submit," nothing happens.
    The little blue bar loads, and completes, but the page stays the same.
    Any answers to this?

  • Apple TV (2nd gen) Support WiFi Captive Portals?

    I can connect to the WiFi but cannot get to he Internet due to the WiFi captive portal.  My iPhone/iPad connect fine. How can one do this via Apple TV? Btw, the provider doesn't support a MAC ACL. It's browser login or nothing.

    Sorry, AppleTV does not support conncetion via a browser login.

  • How can I change the re-direct URL on the WebKit for Captive Portals?

    Hi,
    I have a guest network at the office that is configured with a captive portal for authentication. My MBP detects that it is behind a Captive Portal when the HTTP WISPr request fails and launches the WebKit (ie. the CNA) as designed and displays the login page. When the login is successful, the Captive Portal displays a success and the WebKit then proceeds to re-direct the browser to http://www.apple.com
    Of late, Apple's homepage has become graphic rich and more often than not, loading the page without caching (since the webkit does not cache the webpage loaded) loading Apple's homepage on the guest network takes over 30-90 seconds depending on the traffic on the network. The OS does not allow me to use the network till the page on the webkit has successfully loaded and the "Done" button appears on the webkit and this often becomes irritating.
    Is there a method to change the redirect URL to something less resource hungry like http://www.google.com or a less graphic rich Apple page (like http://www.apple.com/library/test/success.html)?
    I understand that there is a method to disable Captive Portal Handling, ie.
    sudo defaults write /Library/Preferences/SystemConfiguration/com.apple.captive.control Active -boolean false
    However, I don't want to disable Captive Portal Handling in the OS as I don't believe Apps that require internet access will handle the lack of the internet well.
    Any hints would be appreciated.
    Cheers!

    Hey again,
    I did have a look at it and the Settings.plist file isn't very helpful for the issue I have.
    The file defines the probes and exceptions. So you have the default probe WISPr URL in there (http://www.apple.com/library/test/success.html) and the exceptions for specific SSIDs, as an example, attwifi is in the exception list and uses an alternate probe WISPr URL (http://attwifi.apple.com/library/test/success.html). The configuration does not have parameters that would be used by the CNA for the redirect to http://www.apple.com after a succesful Captive Portal login.
    Give it a shot on your laptop, get to a random public wifi like ATT Wifi/Starbucks/Guest Wifi's at office spaces/Boingo etc. and after the successful login, your CNA Webkit will re-direct to http://www.apple.com and the "Done" button won't appear till the page has completely loaded and stays as "Cancel" till the page is loaded.

  • Captive Portal with two or more WAP321

    Hello,
    I plan to use the WAP321 as a WLAN Hotspot. But I need more than one AP. What is the Design for this?
    Do I need to configure every WAP321 with the captive portal and the user need to re-login every time they roam to another WAP321?
    Or can I redirect all WAP321 AP to one captive portal?
    Thank for your support.
    Christian

    Nicola,
    It may be too late, but with the new version1.0.2.3 software you can create a cluster of up to 8 WAP321's in order to share one configuration.  The feature is called Single Point.   Here is a paper on the feature
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps12237/ps12249/brochure_c02-717568.pdf

Maybe you are looking for

  • I reset my iPad2 to factory settings now photos will not sync

    I am having trouble with syncing photos to my ipad.  Very strange since I have been using MAC and ipad for several years now.  My ipad 2 (iOS 7.0.4) recently started having troubles synching to my MAC (OSX 10.9.1) so I reset the iPad to factory setti

  • How to get the NT user id and passwd

    Hi, How to get the NT user id and passwd using form 6i

  • Publication using 'One database fetch for all recipients' is a Failure

    Hi, I have created a Publication in CMC with Crystal Reports as Source Document. When I schedule it with option " One database fetch per recipient" it is a Success. But while using the option "One database fetch for all recipients" it is a Failure. I

  • Can't move photos to smart album

    I have created a smart album based on face recognition, But I am falling to move new photos to the album by dragging them or by copying them. Also, I can't see the album name when choosing "albums" from the "add to" button. Any help will be appreciat

  • CurrentDate as object in Universe Design

    Create object with Getdate() function in universe Design. I had tried, but no result. I find two sites, http://forumtopics.org/busobj/viewtopic.php?t=91514&sid=382f382c24ed3c4b29362a4d87747fdf http://forumtopics.org/busobj/viewtopic.php?p=284562&sid=