Capture Device??

I Bought a Capture Device (Dazzle 150), I was Wonering if if would work with Final Cut Pro 4. If it does can someone tell me how to how to install it in in Final Cut Pro 4.

No clue if it will work but to hook it up ...
run a firewire cable from the device to the firewire 400 (6 pin) port on your computer.
Connect your TV to the device using the appropriate cables (this should be spelled out in the documentation you received with the device)
When you launch FCP, go to
View>Video Playback>Apple firewire
View>External Video>All Frames
View>External Audio>audio follows video.
good luck.
fwiw - all this is spelled out very completely in the first section of the manual.
x

Similar Messages

5.1.4 update breaks HDV capture? Unable to Initialize Capture Device

Problem:
Final Cut Pro cannot capture standard 1080i60 HDV footage from Sony FX1 camcorder. FCP reports "Unable to Initialize Capture Device" when the log and capture window is opened. However, the footage CAN be captured in iMovie (which is interesting, and unacceptable). When HDV>DV downconvert option on camcorder is activated, footage CAN be captured as anamorphic SD, so the camcorder and FW do work.
The problem is occuring on a rock-solid FCP system that I use on a regular basis (mainly for SD editing). It has been approx 2 weeks since I last attempted a HDV capture, the system has been working great with SD footage (still does).
Factors that have changed to my knowledge since HDV capture was last functioning properly:
*Added a new external FW drive into regular usage (a different brand than normally used, no issues with it so far).
*Updated FCP to 5.1.3, and then 5.1.4 when that fix came out. All SD captures and work have been fine so far.
Here's what's interesting...I had a copy of the FCP v5.0.4 .app that I had saved an archive of prior to the crossgrade update. Guess what? I can load it up, and it captures HDV without any problems! With that in mind, this looks like an FCP 5.1.4 issue. But I am at a loss on how to proceed further in troubleshooting. Many thanks in advance for any assistance.
Matt Jeppsen
FresHDV.com
---NOTES---
What I have tried:
*Attempted capture with a different Sony FX1 camcorder.
*Swapped firewire cables and system firewire ports.
*Attempted capture with camera FW chained to an external HDD.
*Unplugged all other external firewire devices from the system.
*Trashed FCP prefs using FCP Rescue 5, created new project using Easy Setup (for HDV).
*Tried different variations of FCP A/V settings, tried all the HDV FW device control presets and the HDV AIC capture preset.
*Per instructions at http://docs.info.apple.com/article.html?artnum=301852 I removed the numbered Quicktime pckg Receipts and re-installed the latest version (7.13). Post-install/reboot, I repaired Disk Prefs and Verified the disk using Disk Util.
*Have also attempted installing QT 7.13 2 and 3 times in a row, also trying disk prefs repair BEFORE the post-install reboot.
Final Cut Pro Audio/Video Settings:
Sequence Preset: HDV-1080i60
Capture Preset: HDV
Device Control Preset: Sony HDV Firewire
Sony HDR-FX1 IN/OUT REC settings:
*VCR HDV/DV: HDV
*COMPONENT: 1080i/480i
*i.LINK CONV: OFF
*TV TYPE: 16:9
*A/V->DV OUT: OFF
System/Software Facts:
*Final Cut Pro 5.1.4
*Quicktime 7.13
*PPC Mac G5 2.7 Dual (2.5GB RAM)
*35GB free on System, 45GB free on internal FCP Scratch disk
Final Cut Pro 5.1.4, G5 DP 2.7 (PPC) Mac OS X (10.4.8)

I think I figured out this vexing problem. I too was having the same issue. Check to see that your Quicktime is newer than 7.1.2. If it isn't you'll have to upgrade it. I only upgraded to 7.1.6 here because I was afraid of going to a really new version. http://www.apple.com/support/downloads/quicktime716formac.html. After I upgraded my quicktime, I ran software update and the Final Cut Pro 5.1.4 update appeared. I hoipe this helps.

Unable to Initialize Capture Device

Hi,
I am having a problem importing/capturing HDV video from my JVC HD GR 1 getting "Unable to Initialize Capture Device".
I have been able to capture fine up to this point, finicky some times to be sure, but workable, then in the last few weeks it began getting more and more finicky (wouldn't connect to camera, restart and it works fine), until just the other day it wont connect no matter what I do!
Help?
Ask questions if you need clarification.
Camera: JVC HD GR 1
Tape: Mini DV
Format: HDV
Software: FCP 5.1.4

Unfortunately when both "Capture" and "Device Control" presets are not set to HDV it wont even try to connect and gives me this warning:
"To capture HDV source material, both the Capture and Device Control presets must be configured for HDV; otherwise, to capture in another format, both must not be configured for HDV."
As a side note when my camera was connecting to FCP. FCP would only give me on screen controls half the time.

Unable to initialize capture device and device control in HDV

I shot with a Sony HVR-Z1U/Z1N and am using a Sony HDV 1080i tape deck to digitize.
I recently purchased a MacBook Pro and installed FCP Pro 5 on it. After getting over some time code issues we were chugging along, when on the 4th tape the image on the log and capture screen suddenly dissapeared (I could get audio and could see the image on the tape deck). Well after taking the tape out, checking and rechecking it I popped it back in and ever since then, I have been getting this error mssg "Unable to initialize capture device and device control."
I have tried deleting the preferences and starting from scratch. If I do that, and choose the easy setup with HDV- 1080i60, it gives me this error "Unable to locate the following external devices- HDV (1440 X 1080) 30fps.
I upgraded to FCP 5.1.2 this morning and upgraded the OS to 10.4.7 and QT to 7.1.3 and still no change.
Im at my wits end, Ive been working on this for a whole week now.
Thank you,
Bugs

It has been reported to take more than one attempt to correct the installation but, if properly executed on a machine without other system problems, the QT reinstall process does work. The key element here is you must reinstall QT after you trash the receipts. The process is listed below.
x
To do a full quicktime reinstall.
Go to /library/receipts and delete any files that say Quicktime followed by a number e.g. Quicktime703.pkg
Go to the Apple quicktime site and download the appropriate version of Quicktime to your hard drive.
Run the Quicktime installer.
Repair Disk Permissions for your System Disk (Disk Utility > Select the system disk > Repair Disk Permissions)
Reboot
If this doesn't work, then the problem lies elsewhere:
1. your system - user preferences, firewire ports or other system elements.
2. your equipment - camera/deck/firewire cables.
3. your process - not setting up the software properly or using the software erroneously.
Listed below is a troubleshooting process. Not all steps are appropriate but the general process of isolating the problem is useful.
Troubleshooting Steps for OS X
by Jan Johannsen (Collected from: Apple>User Tips Library>User Tips Contributions forum)
FIRST AID
01 Completely shutdown, wait a 5 minutes, restart
02 Make sure you're not running out of free space on the System volume
03 Check/fix the filesystem using Disk Utility &/or Diskwarrior
04 Repair permissions using Disk Utility
05 Create a new user account, and see if the problem persists there
06 Clear system & user caches
07 Run FCP Rescue
08 Unplug all USB, Firewire devices except Apple mouse
09 Startup in SafeBoot mode, and see if the problem persists there
10 Reset system firmware
MORE SERIOUS TROUBLESHOOTING
11 Reapply the latest combo updater
12 Run the Apple hardware diagnostic CD
13 Check the hard drive for bad blocks
14 Take out 3rd party RAM
15 Unplug 3rd Party PCI cards
16 Reset PMU
17 Archive and reinstall the OS
18 Reinstall the system from scratch
19 Send the machine back to Apple

Detecting Video Capture Devices without Installing JMF

Hi All,
I want to detect the video capture devices, without installing the JMF.
I had included the jmf (windows version) in lib path in netbeans ide. I am able to detect the audio capture device. But unable to detect the video capture devices. But if I install the JMF, I am able to detect the Video Capture devices in My system. Can anyone help me?
Thanks,
Vinoth Kumar.

YES! Please take a look at SIP Communicator project. They have all what u want.
The main idea is copy all .dll files to System or System32 (Please check files which JMF will copy to ur computer and where).
U need to have jmf.jar and sound.jar too ( maybe more) in your computer.
Your program should have DirectSoundAuto.java, JavaSoundAuto.java, JavaSoundDetector.java, JMFInit.java. Those files are in JMStudio source code. They are used to detect all capture devices and register it to JMF, but wait !!! where they will be saved? In order to save information about capture devices which are detected, you should create "jmf.properties" file in the same location with jmf.jar.Therefore, u should modify the JMFInit.java so it can check if the "jmf.properties" exists. If it's not, you have to create it.
Check SIP Communicator at Folder "media" then "device". They have modified those files I mentioned above and created some new files to SC can detect more devices.
Edited by: tamngminh on Sep 16, 2008 9:50 AM

Video capture device bad image/no sound

Hi !!
I bought this "grabby" usb dongle from terratec to record old vhs cassete on my computer, but is doesn't work on linux. (It works ok on win7, so cable-connections problems are excluded)
On vlc I did 'open capture device', choose /dev/video0 for vid, hw:2,0 for sound(tried them all anyway), and PAL/SECAM video standard.
Problem is I have a super crappy video image (on mplayer also), and no sound. The video is colored, I recogize it, but the pixels are huge, it's awfull.
After some research I found that a module named em28xx is supposed to handle this device. I found some forum post here and there about the sound problem, it is addressed with a 3years old patch on em28xx-cards.c (which doesn't exist on my machine, so I couldn't apply it).
Here is dmesg :
[ 8371.430051] em28xx audio device (0ccd:0096): interface 2, class 1
[ 8371.430074] em28xx audio device (0ccd:0096): interface 1, class 1
[ 8371.438360] em28xx: New device TerraTec Electronic GmbH TerraTec Grabby @ 480 Mbps (0ccd:0096, interface 0, class 0)
[ 8371.438363] em28xx: Video interface 0 found
[ 8371.438365] em28xx: DVB interface 0 found
[ 8371.438511] em28xx #0: chip ID is em2860
[ 8371.554008] em28xx #0: i2c eeprom 00: 1a eb 67 95 cd 0c 96 00 50 00 11 03 9c 20 6a 32
[ 8371.554020] em28xx #0: i2c eeprom 10: 00 00 06 57 0e 02 00 00 00 00 00 00 00 00 00 00
[ 8371.554029] em28xx #0: i2c eeprom 20: 02 00 01 00 f0 10 01 00 00 00 00 00 5b 00 00 00
[ 8371.554039] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 00 00 00 00
[ 8371.554048] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554057] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554067] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 32 03 54 00 65 00
[ 8371.554076] em28xx #0: i2c eeprom 70: 72 00 72 00 61 00 54 00 65 00 63 00 20 00 45 00
[ 8371.554086] em28xx #0: i2c eeprom 80: 6c 00 65 00 63 00 74 00 72 00 6f 00 6e 00 69 00
[ 8371.554095] em28xx #0: i2c eeprom 90: 63 00 20 00 47 00 6d 00 62 00 48 00 20 03 54 00
[ 8371.554104] em28xx #0: i2c eeprom a0: 65 00 72 00 72 00 61 00 54 00 65 00 63 00 20 00
[ 8371.554114] em28xx #0: i2c eeprom b0: 47 00 72 00 61 00 62 00 62 00 79 00 48 00 00 00
[ 8371.554123] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554133] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554142] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554151] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 8371.554163] em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xd3498090
[ 8371.554165] em28xx #0: EEPROM info:
[ 8371.554166] em28xx #0: AC97 audio (5 sample rates)
[ 8371.554167] em28xx #0: 500mA max power
[ 8371.554170] em28xx #0: Table at 0x06, strings=0x209c, 0x326a, 0x0000
[ 8371.554172] em28xx #0: Identified as Terratec Grabby (card=67)
[ 8371.856372] saa7115 4-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #0)
[ 8372.495384] em28xx #0: Config register raw data: 0x50
[ 8372.515361] em28xx #0: AC97 vendor ID = 0x83847650
[ 8372.525227] em28xx #0: AC97 features = 0x6a90
[ 8372.525231] em28xx #0: Empia 202 AC97 audio processor detected
[ 8372.908213] em28xx #0: v4l2 driver version 0.1.3
[ 8373.760714] em28xx #0: V4L2 video device registered as video0
[ 8373.760718] em28xx #0: V4L2 VBI device registered as vbi0
And lsmod :
[user@OGwncMO ~]$ lsmod | grep em28xx
em28xx 88986 0
tveeprom 13809 1 em28xx
videobuf_vmalloc 4351 1 em28xx
videobuf_core 16231 2 videobuf_vmalloc,em28xx
v4l2_common 5370 2 saa7115,em28xx
videodev 100564 3 saa7115,em28xx,v4l2_common
i2c_core 20508 7 i2c_i801,saa7115,em28xx,nvidia,v4l2_common,tveeprom,videodev
usbcore 147434 10 uas,ath3k,btusb,snd_usb_audio,usb_storage,em28xx,snd_usbmidi_lib,ehci_hcd,usbhid,xhci_hcd
From what I see my guess is that the module supposed to handle this hardware is present but doesn't do its job properly...any help?

Hi again !
Thanks for you tip nomorewindows. The programs tvtime and xawtv worked out of the box concerning video !! xawtv, however, crashes everytime I try to resize the (very) small window. As for tvtime, there is no sound (output is it can't open /dev/mixer so I guess it's fixable, I'll look into it).
I started reading the doc but I didn't found yet if it was possible to record the output with these program...
Concerning the cables, you are right they are not special at all it is standard : there is the triple (yellow=composite video, red/white for audio) cable and a fourth one for video but with inferior quality, I didn't connect it (it's either the yellow or this one for video)

How to connect a video capture device to Satellite M30X 127

I'm going around in circles trying to find a video capture device that will function with a laptop and would be grateful for advice. By way of example, I'm now looking at the 'Canopus ADVC-110', although still looking around (but not Pinnacle, who seem to have a terrible reputation for capture items).
Problems include:
1. Main problem is - many video capture external devices require a 'line-in' to PC for good quality audio transfer. This laptop doesn't have a line in, only the mike and headphone jacks. In addition, I've also tried a few RCA pins in the 3.5mm microphone/headphones jack and they were too small. How to solve the problem of getting audio from vcr to my PC?
2. The ADVC-110 connects to the PC via Firewire (and S-video), but is a SIX-pin type. M30X is a FOUR-pin type. Are there adapters available?
3. Some capture programmes seem to require huge capacity of RAM. Is a laptop going to be suitable to do the job? (I simply want to capture old vhs tapes from vcr to PC, then burn to DVD with Nero 7 or similar).
Thanks in advance!

Hello
You are right! You must use external device for signal transfer to your notebook. I dont know where you have this info but I have good experiences with Pinnacle product. For data transfer I have used USB port.
'Canopus ADVC-110 is not known to me but I dont see any reason why this should not work well. Use delivered software for video capturing and there should not be any problem.
Only thing is that after recording the whole video material must be prepared for burning and unit need a lot of power to do this well und fast. When you buy this and want to use on right way I recommend you to expand RAM to 1GB.
Compatible memory modules for your Satellite M30x are:
PC2700 512MB (PA3312U-1M51)
PC2700 1024MB (PA3313U-1M1G)
Bye

Advice Needed for Video Capture Device

Hi,
I'm looking to buy a USB (or Firewire if they exist) video capture device that can take S-Video and composite connections. Could someone recommend me best one under $150 that is compatible with Snow Leopard? Also, and more importantly, does anyone know if it is possible to capture the signal via Quicktime Pro or Final Cut Pro rather than bundled third party software.
Thanks!

I used the predecessor to the Canopus ADVC55 to load VHS tapes into a mac. As I recall I brought the firewire signal into iMovie (could have been Final Cut Pro too, as I had both on the system). Here are the specs: http://www.grassvalley.com/products/advc55 . Also some comments on it at http://www.amazon.com/Hardware-ADVC-55-d-Converter-Ntsc/dp/B000HGVZG0/ref=sr_1_2 ?ie=UTF8&qid=1323954590&sr=8-2 Here's another source to buy it: http://www.bhphotovideo.com/c/product/312315-REG/Grass_Valley_602005_ADVC_55_Ana log_to_Digital.html .
They also make an ADVCmini, which I haven't used, which is probably less expensive, with specs at http://www.grassvalley.com/products/advcmini

Adobe premiere elements 12 with diamond vc500 one touch video capture device.

Adobe premiere elements 12 and using Diamond vc500 one touch video capture device.
AVI files will not load into Adobe premiere elements 12.
I bought what I thought were the two best software and capture devices.
I am archiving old VHS tapes and using Diamond vc500 capture software called EZ grabber. I thought the best archiving format would be AVI files. As I just started this project. I am willing to do what is needed.
That even being, going and buy another capture device that being for a VCR to PC using a USB are even a Video card.
EZ grabber software ask you to record in what format. I picked AVI. There is DVD - SVCD - VCD - MPG4. I want to archive then go back and edit. The DVD or SVCD format, is that not the same as mpeg 2?
You and I know the drill. Saving in what long term archive format and that dare thing about video compression and losing quality of the videos. Its all a nightmare.
Once again I am willing to buy another capture device for a VCR that will work with Adobe premiere elements 12.
Help please with long term archiving format and capture device.
Thanks

The answer is B.
Capturing the VHS content to computer (via the Diamond vc500 and USB connection and EZ grabber) to obtain an .avi file on your computer and then trying to import that into Premiere Elements with its Add Media/Files and Folders?
When I do that, the Adobe premiere elements 12 crashes or only loads a 2 mins of video.
The firewire connection device "Canopus" product sounds great. But I really don't want to spend that much on my home videos. My PC does not have a Firewire connection. So add a new card for that and the Canopus product. I could just pay someone to do my VHS tapes.
Diamond vc500 $35
Adobe premiere elements 12 $65
Firewire card $50 plus
Canopus $180
$330 is way too much for simple home VHS videos

Use a capture device twice at the same time?

I have write a application using JMF. But I have a big question that how can I use a capture device several times at the same time????
For example:
I create a player to play video from my webcam on my PC ,and then I want to send the video stream from my webcam to another PC at the same time. But I failed--only one task can work.
For example:
1, I write a class Player and another class RTPTransmit. Then I send the same medialocator to two of them. Then there will be a exception said that capture device is in use. And only one task can work.
2, I write a class Player and another class RTPTransmit. Then I use :
dataSource1 = Manager.createDataSource( locator );
dataSource2 = Manager.createCloneableDataSource( dataSource1 );
then I send dataSource1 to Player object to play video on local PC and send dataSource2 to RTPTransmit to send video to another PC. But only one task will work too.
My question is that how can I use a capture device several times at the same time???
I have tried several ways and sill can not find a method. If anyone know how to do,could you tell me please? Thank you very much.

Yes ,I use Manager.createCloneableDataSource() method to create the clone of the datasource ,but it can not work too. The java doc illustration is :
Creates a cloneable DataSource. The returned DataSource implements the SourceCloneable interface and enables the creation of clones by the createClone method.
If the input DataSource implements SourceCloneable, it will be returned right away as the result. Otherwise, a "proxy" DataSource is created. It implements the SourceCloneable interface and can be used to generate other clones.
When createCloneableDataSource is called on a DataSource, the returned DataSource should be used in place of the original DataSource. Any attempt to use the original DataSource may generate unpredictable results.
It means that if I clone a datasoure from original datasource, then the createCloneableDataSource() method will return a datasuouce implements interface SourceCloneable, right ? I see that the intereface SourceCloneable has a abstract method createClone() , but when I use createCloneableDataSource() to get a source clone, I find that I can not use method createClone(), why??? For example: data1 is the
orginal datasource. Then:
DataSource data1 = Manager.createDateSource( locator );
DataSource data2 = Manager.createCloneableDataSource( data1 );
now data2 is the "proxy" datasource which implemnets the interface, right? But I can not use data2.cloneClone() ,why? Then I write the fllowing code:
DataSource data3 = Mangaer.createCloneableDataSource( data2 );
DataSource data4 = Manager.createCloneableDataSource( data2 );
playOnLocalPc = new PlayOnLocalPc( data3 );
playOnLocalPc.start();
rtpTransmit = new RTPTransmit( data4 );
rtpTransmit.start();
PlayOnLocalPc and RTPTransmit is my own class to play or transmit video stream. But they can not work at the same time. If I play video from webcam on local PC and then start to transmit stream to other PC , the play window will become black. Why?????It is too strange. Dose anyone know the reason ,please tell me, thank you very much. Giving some example code will be better:) Thank you again!

Can't get driver to work with ezcap usb 2.0 video capture device on windows 8.1

I have an ezcap video capture device that works fine on my windows 7 machine but will not work in windows 8.1. The software (arcsoft 3.5) functions properly but will not let me select the video grabber as a source. The driver itself indicates not compatible with 8.1 and the there are no drivers out there that I can find to address this issue? Any known solution would be helpful.

Hi,
It is not from HP. Please try driver from the following link:
http://www.ezcap.tv/ezcap116-drivers?zenid=r53fvgj1n510tdme9itqc9ql52
(After the first screen shot).
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Media Encoder not finding "audio capture device"

Hi,
Im using Adobe Flash Media Encoder with Dxtory for Twitch streaming, and at first it worked fine. Recorded both my mic and game audio perfectly. Then seemingly suddenly, I fired it up and it wouldn't stream the game audio. It would my Mic, but thats it. I then unplugged the mic and it started saying I had no Audio Capture Device. I checked in Dxtory and its set up the same as it was when it was working. It picks up both the mic and speakers like it should. I have uninstalled this program multiple times, both 3.1 and 3.2 versions, and each time when I re-download it, it loads up the same profile I had before. So when I am uninstalling it, its not uninstalling everything for some reason. Even though the program is no where to be found after its uninstalled. I have downloaded xsplit, and it picks up the game audio and my mic. So its just this program. Anyone have any ideas? I cant seem to find anything online about this issue.
Thanks!

From where? PP sequence? PP bin? PP Source Monitor? Watch folder?

Unable to Initialize Capture Device - Works fine in iMovie

Am using a Sony HDV HDR HC1E Pal Handycam
Final Cut Pro 5.1
QT Pro 7.1.3
Works fine with cassettes in HDV - imports into FCP fine
Am trying to import a cassette recorded on that camera in DV LP
Works fine in iMovie
Have deleted the QT packages and reinstalled QT
Still am getting the 'Unable to Initialize Capture Device' message when using log and capture.
Settings on camera
VCR Auto (have also tried HDV or DV)
iLink conversion off (i.e.don't convert hdv-dv)
TV type 16:9 (have also tried 4:3)
Component 1080i/576i also tried 576i
Annoying thing is that works fine in iMovie but not FCP?!!
Any help GREATLY appreciated!
Thanks!
Hannah
iMac 20 Flat Screen G5 1.8Ghz 1.5GB SDRAM Mac OS X (10.4.8) 200 GB and 120GB External Hard drives

I would like to add the following in hopes that someone will come up with a solution. The problem lies somewhere in Quicktime and the FireWire capture. I have the exact same camera and problem, and can assure you it has nothing to do with cam settings or DV LP. Once your system is stuck in this HDV mode, it would seem that regular DV can not be used again. I also have 2 other DV cams that are not HD. One is PAL, one is NTSC. I would further add that my external FireWire iSight no longer works in any application. I do not receive error messages, I simply get the spinning beach-ball of death.
I have a Dual G5 2.7 with 4 gigs RAM running FCP 5.0.4 on OS 10.4.8
I have run Cocktail, rebuilt permissions and re-installed Quicktime 7.1.3 four times as per Apples tech article 301852
I have used FCP Rescue 5 to clear preferences
I have captured footage from both regular DV cams to iMovie and then added the footage to FCP. The footage plays on the screen of both DV cams flawlessly via FCP. (I can also capture HDV in iMovie as well)
I have tried logging footage directly through the QuickTime application with both DV cams and my iSight and get the same beach-ball of death as FCP.
Why can iMovie work with these devices flawlessly yet QuickTime can not.
Why does it seem like the system is stuck in some kind of HD mode.
Just to point out the obvious:
I have no other FireWire devices other than the cameras and I only connect one at a time.
I have shut down, disconnected and re-connected before attempting to use the devices.
I have booted my G5 from a second system disk and everything (HDV cam PAL DV cam NTSC cam and iSight) function flawlessly on all the FireWire ports of my machine.
I have worked with FCP for about 6 years and Macs for 20. I understand the easy set ups etc.
Spent way too much time customizing my system to think about the clean install route, so I hope someone can shed some light on this.
Thanks
Lorne
PowerMac Dual 2.7 GHz PowerPC G5 4 GB DDR SDRAM 400 GB and 250 GB Internal Drives Mac OS X (10.4.8)

After using video capture device to copy VHS to DVD, burnt DVD will play on computer but not

After using video capture device to copy VHS to DVD, burnt DVD will play on computer but not on DVD player. Tech support for the VCD said my HP DVD burning software has to burn "DVD Video and not DVD data" and to check with HP. How can i check myself.

Grahamster, welcome to the forum.
I recommend trying CDBurnerXP for burning video CD's. I have been using it for years without a glitch. I use it mainly for burning ISO's, but have used it for all types. Please let us know if it works or not.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Slightly OT: bios screenshot capture device

Somebody here (or perhaps on the Framers list) asked about techniques to get good bios screenshots. For those who might be interested, I just came across a good example of screens, and a mention of the video capture device used.
Image: http://www.hardocp.com/image.html?image=MTI5NDcxNTE1M1NNSTgwSDVodGFfM18yX2wuZ2lm
Tool:
Dan_D, forum editor, said:
"They are taken with an old school DVC-80 S-Video capture device using an S-Video output on an NVIDIA graphics card. The AMD / ATI's produce inferior results via S-Video so I never use those for screen shots."
http://hardforum.com/showthread.php?s=a8982caf7410523d9bd17933692b157f&t=1578842&page=2

I don't believe any Windows (or DOS) screen capture app can take a capture at the bios stage, no.
It would require a custom BIOS to do that, because all that is running is BIOS firmware during those screens.
However; historically, BIOS supported the [PrntScrn] key on the keyboard, and would dump a plain text copy of the current BIOS screen to the parallel (LPT) port.
What happens on machines lacking LPT is unknown to me. I have even less clue on what EFI and UEFI implementations do with PrntScrn, if anything.
The usual solution when you need an exact screen image is to use a digital camera.
Use a shutter speed of 1/30 second or slower, to avoid any screen refresh or black-screen-insertion artifacts.
Use whatever focal length provides the lowest pincushion or barrel distortion, usually telephoto.
Use a tripod. Be on-axis. Use the self-portrait timer if you don't have a cable release.
Set a custom white balance using an all-white screen.
Since BIOS displays are 640x480, any Mpixel count over 1Mp will do to avoid sampling artifacts when you crop, de-rotate, resize or otherwise morph the image to the final 640x480.

Importing problems (hi 8 camera-capture device-imovie)

i am importing from an old canon es3000 hi-8 (analog) camera, through a miglia "director's cut" capture device, to imovie (via firewire) ... there is fragmented line at the bottom of the frame in imovie during import. will that show up in idvd later? also, the imovie is not seperating the clips, so i end up with one long clip. after about 10 minutes the digital footage in imovie becomes fragmented throughout the frame. does anybody know why this is happening? thanks in advance, R.B.
Mac G5 Mac OS X (10.4.7)

see the other post
Don't double post Your questions but address right forum.
Yours Bengt W

Capture Device??

Similar Messages

Maybe you are looking for