Capture from Sony HVR-Z1U

I have recently purchased a Sony Z1U and was unable to capture in FCE4. I later found out that FCE4 will only capture from the Z1U in DV mode and NOT in HDV. Why is this? Is all my HDV media useless now that I have FCE4? Should I only shoot in DV mode from now on? I also have a small Sony HRD-CX7. Will FCE4 capture from this device?
Any help for this newbie would be appreciated!

"do not connect to the computer. Connect it to the hard drive so they are on a single FireWire chain. The computer will have difficulty passing information back and forth on FW when there are multiple devices on multiple ports but on a single bus"
In theory this may be true, however my external drive only has (2) 1394b ports. My camera has (1) four pin 1394a port that converts to a six pin 1394a through the cable assembly. There is no way to chain these components together (via my external drive anyways) as far as I can see. Is this a critical issue? Should I invest in a different drive? I guess I could connect to my ED via esata using an express card. Would this approach lessen the load on the FW bus during capture and delegate a separate bus for ED control?
Any thoughts on this?
Message was edited by: Chad Clemens

Similar Messages

Problem Capturing from Sony HVR-A1U to FCP 5 using HDV preset

Hi,
i just got a Sony HVR-A1U and am new to HDV. I am a professional editor so i have a full understanding of FCP. Here are my problems and questions.
Specs of system : Power Mac Dual 2Ghz G5, 1.5GB Ram, GeForce FX 5200 64mb (Do i need a better GFX card?)
1) When i setup the project settings at the start I selected HDV 1080i/60, it automatically states "Codec not found. You may be using a compression type without the corresponding Hardware card." I am quite sure that i have all the codecs i could have without having a hardware card, since i don't have a hardware card. Does this mean that i need a blackmagic HD card or a Kona card just to process the HD into FCP as HDV 1060i/60 even though it is through firewire?
2) I advanced to the Log & Capture mode with the HDV settings, set properly across the board. I can not see picture, can hear audio and can log clips. When i capture it captures black for video but captures the audio just fine. I figure this is because of the missing codec which encodes HDV for FCP from Sony's HDV encoding?
3) I can capture on the fly with the Apple Intermediate Codec, no Log and Capture screen comes up, just a dialogue box that asks me to name the clip. I understand what this codec is and find that i am stuck at the moment using this until I find a way to capture the other way. Is there anyway to have the Log and Capture screen launch using this codec?
4) I can not have pre-logged clips using other methods and then batch capture them using the Apple Intermediate Codec, it just reverts to capturing on the fly. Anyway to Batch Capture using the Apple Intermediate Codec?
Funny thing is that i can digitize fine in iMovie HD although i don't know what codec it is using. This totally baffles me that it works in a certain manner, i can get the job done, but not the way i should be able to. I've been using FCP since '99 and have never encountered something in this manner. And since this is my first experience with FCP and HDV i have nowhere to go from here except get some help or settle for what i can do and change my normal post-production workflow.
A question i really want to know about is whether i need an extra hardware compnent, i know i asked that question above, and i could understand if i did. (i.e GFX card or Capture card - even though i am going through firewire)?
I appreciate any help, i might not respond over the next couple of weeks because i am shooting in Europe and will be back stateside at the start of February, so i will not be active on this post until then. Any input would be great and when i get back i will have loads of footage that i will need to digitize, so i will be very open to help with troubleshooting as well.
Thanks again!!!
Gabe
PowerMac G5 DP 2Ghz, 1.5GB Ram, GeForce FX 5200, 20" Cinema Display Mac OS X (10.4)

All the settings are proper, like i said, it captures with the apple codec for HDV but that is only good for on the fly. iMovie captures it fine, it's just when the settings in FCP are set for HDV it won't capture picture through log and capture.
Are you guys actually reading my post??? I have given all the information that i can, settings are proper, so the post so far are completely redundant.

Capture from Sony HVR-A1E

Hi
I have Final Cut Pro 5.1.4. I recently acquired a Sony HVR-A1E. It shoots in HDV 1080i.
I'm trying to work out how I can capture the video using FCP?
Is there an appropriate capture preset and device control preset?
For capture preset various things are listed such as HDV, DVCPRO HD 1080i50 48KHz, DVCPRO HD 1080i60 48KHz and others.
The camera connects to my Intel iMac by USB. I notice that FCP seems to list Firewire throughout its device control preset menu. Is it possible to have device control for USB?
Thank you for any assistance you can give

Hi
I've found the FireWire port
They've called it "iLink".
A bit of "googling" with "iLink" has shown me that this is commonly used on Sony Camcorders.
I have used Sony Camcorders before and but they've been hired ones and I think it has always been that the person hiring it out has pointed at the "iLink" port and called it the "FireWire" port, so I've never caught on that this different name exists.
I'm buying the right cable next...
When it is plugged in and working (touch wood) I will come back and do this "helpful" and "solved" thing.

Why is my audio is out of sync with my video on hd capture from sony camera

My System
Win 7 64 Bit
Asus P5Q-E Motherboard
4 GIGS DDR Patriot Ram
Pentium quad 2.8
Ati Video Card
Onboard Audio
CS3 Premiere And Encore
I have a Sony HVR Z series HD camera from sony. I will capture a tape and it will be out of sync. I will then recapture and it may be in sync or not, this is really frustrating especially for music videos and weddings, actually a nightmare. I'm not quite sure as to the reason as it happens in Adobe Premiere cs3 and cs4. I have updated everything. Do you thing I need a 10000 RPM os system drive. Any help would be appreciated.
Joan

I have 2 Sony HDR FX1 and 1 Sony HVR Z1U and it works great in both CS3 & CS4 so something is wrong with your setup or camera.
I only have a 7200 SATA drive for capture.
I dont know if a bad cable would cause this.
Harm has a couple other ways to capture that he says it keeps the audio in sync better but I have yet tried it but im sure from what I have read here that it works good.
Here is a link to his Tools Article.
http://forums.adobe.com/thread/504907
Here are those 2 capture ways:
Capture
Scenalyzer: http://www.scenalyzer.com/main.html for capturing SD material
HDVSplit: http://strony.aster.pl/paviko/hdvsplit.htm for capturing HDV material
Hope this helps: Glenn
EDIT:
I have an 5 year old system.
On Bills PPBM4 test you can see that I scored second to LAST on speed so even my system can capture fine.
http://ppbm4.com/Benchmark.html
Take the test and see how your system is running. It doesnt take to long.
Glenn

I am trying to capture from Sony HDV 1080i VTR FCP giving an error of not able to initialize

i am trying to capture from Sony HDV 1080i VTR FCP giving an error of not able to initialize. I am not able to capture the content in DV mode. i am using a Firewire 800 to 400 converter and a 6 pin firewire cable to connect to the SonyHDV VTR. Please suggest me how do i do this.

The 800-400 converter plugs have proved a problem for this. What version of the software are you using. It sounds like an older version of FCP, if so you should ask your question on the Final Cut Studio forum.

Capturing from Sony Z 1

Can anyone tell me what I need to choose in capture presets (or elsewhere) to capture from Sony HDV Z1? I just get the picture squeezed like the persons going throw a funny mirror..!

What format are you trying to capture: HDV, SD, ProRes?
Which ever one you desire will require setting the Easy Capture settings in FCP before you try to capture. And in the case of SD you will need to set your camera to convert from HDV to SD prior to capture.
Brock Fisher
San Diego

Can not capture from Sony HDV 1080i (recording in 60i)

Hello
We are trying to capture from the above camera to a Mac Dual G5. We are using FinalCutPro 5.1.2. We are using a FireWire 400 cable to connect to the front of the computer (have also tryed back of Cinema Display). The footage was captured in HDV1080/60i, and we have tried the corresponding formats in Easy Setup (Basic, standard, Apple Intermediate).
The problem: we can control the camera from the Log and Capture windows, but when starting capture, no data is coming in, and the program therefor gives up after a few seconds (displaying a no data error message).
We have tried Batch and Now capture. We can log clips, and get the correct time code, but can not capture those clips due to the no data problem.

This is a good workaround for curing your camera recognition problem with FCP (if that's what it is):
First, check that your Easy Setup / Timeline / Camera or Deck Settings are all exactly the same, then making sure your camera or deck is in VTR mode, try to capture again.
FCP uses a different form of QT than iMovie for capturing, so if the camera works in iMovie (or if it's listed in System Profiler) but not FCP, it obviously means your Mac can see the VTR but FCP can't, so you need to do this QuickTime fix.
http://docs.info.apple.com/article.html?artnum=301852
Follow the instructions carefully and you should have things running in no time - it's quite safe but you must Trash the Receipts AND re-install QT from the link provided.
If the Camera / Deck isn't recognised by iMovie or System Profiler, try resetting the Firewire Bus . . . Turn off the Mac and disconnect the power and all Firewire cables. Leave it for 30 mins then connect back up.
Still not working? Try a different Firewire cable.
Failing all this, try resetting the PMU (Power Management Unit). The method varies from machine to machine, so visit the Apple site and search for it in support.
Don't use iMovie for capturing - it doesn't give you a timecode and that's very important.
Let us know how you get on!
Andy
Quad 8GB. 250+500 HDs. G-Raid 1TB. NORTON. FCP 5.1.2. QT 7.1.3. Sony HVR Z1E Mac OS X (10.4.7)
"I've taught you all I know, and still you know nothing".

Unable to capture from Sony HDFX1 camera

Built a new PC and utilized a top end ATI Radeon dual video card. Running Vista Ultra OS(hmmmm), plenty ram, processor, etc.
PC does not see my camera when I plug in for capture. Do I need a special codec or 1394 HD drivers available for HD capture from ATI or from Adobe perhaps?
Frustrated

If the Vista install was a standard installation, Vista should recognize the camera automatically and install the correct drivers. Nothing you need to do. Make sure that you connect the firewire cable first between the camera and the on-board firewire connector. Do not try to connect it to the ATI card. Once the cable is connected, turn on the power on the camera and set it to VCR. Vista will then install the necessary drivers automatically and if they have been installed previously, show the autoplay box. Make sure that the menu in the camera is correctly setup to use the iLink connection and the format you shot in, so either DV or HDV. Consult the Sony manual for that. If the does not work, try a different cable first.

My audio gets out of sync with my video after capturing from Sony XDCAM

Everything was fine. I captured content from my Sony XDCAM, created pieces, no problem. Imported a .mov from my older FCP (5.1.4). FCP told me I needed to change my settings in order to use the .mov with my current timeline. I said OK, fine. Now, when I capture from my XDCAM some of the audio is in sync but it goes out fairly quickly. Any Ideas? I noticed in the bin the clips which are out of sync have a different data rate then the good ones. HELP!

Everything was fine. I captured content from my Sony XDCAM, created pieces, no problem. Imported a .mov from my older FCP (5.1.4). FCP told me I needed to change my settings in order to use the .mov with my current timeline. I said OK, fine. Now, when I capture from my XDCAM some of the audio is in sync but it goes out fairly quickly. Any Ideas? I noticed in the bin the clips which are out of sync have a different data rate then the good ones. HELP!

Bad quality of capturing from sony SR5e.

I have used iMovie for several months. It worked quite well at first. However, in these days, problems are always appeared. Firstly, it always got rather bad quality of clips after capturing from my SONY HDR-SR5E. It seems lost some frames; all of the objects in it appears jumping when they are moving. Secondly, when I restarted the iMovie and tried to capture again, iMovie just quit unexpectedly. I have also tried using Final Cut Express to capture in my machine, it works fine and get a smooth clip comparing with iMovie.

Already try this. This is not the problem ...
It's something on the rendering of the colors. You can see that on those 2 screenshots on the image referenced in the post on my blog :
- Firefox = http://julien.coillard.free.fr/images/ImageFFox.jpg
- IE7 = http://julien.coillard.free.fr/images/ImageIE7.jpg
To see the difference you to load the pictures (don't compare them on Firefox) and the original picture as loaded on my blog is here :
http://julien.coillard.free.fr/images/valsaintes2.jpg
Sorry if my explanation is not clear, i'm french and my english is not excellent

Unable to capture HDV in FCP 6.0.1 from Sony HVR-Z1P

Hi I'm attempting to capture HDV footage from a Sony Z1.
I am trying to capture some HDV footage I shot with the Z1, but FCP simply refuses to recognize the Z1
I'm certain I've got all the settings correct:
- Camera is set to HDV firewire out
- capture presets is set to HDV
- device control preset is set to Sony HDV FireWire
- sequence preset is set to HDV 1080i50 (I'm in Australia)
- footage IS HDV 1080i50
But I keep getting the "Unable to Initialize Capture Device and Device Control" popup. I've tried everything
- rebooted the camera
- restarted FCP
- rebooted the system
- changed the capture/device control settings in FCP and tried out a regular DV deck to make sure it wasn't the cable
Nothing has worked.
I'm on a MBPro I7. No Kona card or anything like that, just trying to capture through firewire.
Any suggestions would be greatly appreciated.
Thank you,
Matt
At present it will capture HDV in IMovie but not FCP 6.0.1
Message was edited by: Matt Blyth

Thanks Adrian, since posting the thread I've thought of that too but unfortunately to no avail. From other forums I've read this seems to be a central theme to the solution to my capture woes. I since have sorted the problem it was in Audio/Video Settings.
In the end I set my Audio/Video Settings to:
Sequence Preset to: Apple Intermediate Codec 1080i50
Capture Pre-HDV- Apple intermediate Codec
Device Control Preset: Sony HDV 1080i50 Firewire
And hey presto my I'm capturing HD without any problems. Thanks everyone for your suggestions.
Message was edited by: Matt Blyth

Capturing HDV 1080i50 with Sony HVR-Z1U

Long winded question... hope someone can offer some insight.
The answer to this may have been posted earlier, but sifting through the topics, I couldn't find any relating. If someone could be so kind to link me to any related topics, that would be helpful.
I'm editing a project in Final Cut Pro 5.0.4 that is a mix of HDV and DV, but will be finishing the final product in HDV. I've edited the original project in regular DV, but am batch capturing in the HDV footage according my XML.
But I can't seem to connect the camera.
Easy Setup: HDV - 1080i50 gives me an error "Unable to locate the following external devices: HDV (1440 x 1080) 2 fps)"
Going into Audio/Visual Settings and setting Capture settings to HDV and Device control preset to HDV Firewire gives me an error "Unable to initialize capture device and device control" (or for any device control preset with the HDV Capture setting for that matter)
Any device control preset with "HDV - Apple intermediate codec" will give me an error with "Unable to initialize HDV deck. Please make sure a deck is connected and try again".
Camera: In/Out VCR mode is set to Auto, i.Link Converter is set to "Off", A/V->DV Out is set to on.
Camera is on and plugged in. I've tried plugging the firewire into different ports and have also tried various firewire cables. Sometimes the device is controllable, but all it does is play the tape, never gets around to capturing anything.
.... sigh....
Thanks in advance,
_tess
Power PC G5 (iMac) Mac OS X (10.4.4)

AIC is not going to work for recapture, AIC doesn't use the original timecode off the master tape. Make sure you setup HDV 50i and before connecting the firewire cables go into the camera vtr mode then menu, then rec in out and set the ilink convert to off for HDV. the Camera will show HDV lights. Then connect to the computer and open log and capture.
Good Luck
Z1&V1user

Windows Movie Maker - unable to capture from sony handycam

I am using Sony Handycam DCR-HC2 camcoder and my laptop is sony vaio vgn-nr160e. Before upgrading to windows 7, I was able to capture home made movie with Click to DVD program via i-link cable with vista home.
From the time I update to Windows 7, I am unable to capture home movies. Presently I am using windows movie maker 2.6. When I connect my handycam to laptop with i-link, it won't reconize.
Please some one guide me, we are planning a 2 week vacation and I am going crazy with this issued ( I am an avg tech guy, not a expt)

I have
Windows 7 RC
Sony handycam DCR-TRV19
Sony iLink cable
Full Windows Live package installed
and have had similar results.
With the Sony cable (verses a 4 pin to 4 pin cable) I do get DV IN on the camera when I connect.
But in device manager it does not show up under IEEE or as an Image Device :-(
That's as far as I have gotten. Hoping someone can find the little nugget to get this going.
Hi
Here are a couple of links that may help.
Sony eSupport - Digital Camcorders
Sony eSupport - DCR-TRV19 - Support
Hope this helps.
Thank You for testing Windows 7
Ronnie Vernon MVP

Capturing from Sony DCR in Premiere Elements 13 not possible?

Premiere Elements does not find the device (SONY DCR-TRV120E PAL), although it is recognized in "Devices and Printers" as "AV/C Subunit / Sony DV Camcorder" (WIN 7) and the device is also recognized and capturing correctly under MS Movie Maker.
Thanks for any helpful advice!
Oliver.

Oliver
Thanks for the reply.
Hope you can use the workarounds suggested in the Adobe document.
Are you within 30 days of purchase from Adobe direct on this one? If so, you can seek a refund/money back from Adobe.
If you purchased from an authorized reseller, then you have to deal with the seller according to the sellers return/refund policy.
If an Adobe online purchase, then Adobe Chat Orders should be able to take care of the refund details.
Contact Customer Care
Premiere Elements
Membership, Account, Payment
Payments, Invoices, Orders
If the link does not hold its set, then you will need to navigate to the Chat Panel using the above titles as guides.
Best wishes
ATR

Output to tape on Sony HVR-M10U

I'm new to FCP and editing but was doing OK in SD. Now my client has started recording HD on a Sony HVR-Z1U camera and has bought a Sony HVR-M1OU deck. I have a G5 quad and Final Cut Studio (FCP 5). I captured a scene using the HDV - 1080i60 easy set up. It looks like letterbox on the canvas and I edited it and now want to get it to tape. I only need to output it SD. I have tried many ways but so far have been unable to get it out to tape. I've spoke to the Apple Tech support three times and to Sony tech support and tried all kinds of things that they have suggested and nothing has worked.
If I try to use Edit to Tape I get "Capture preset is set to HDV. Edit to tape is unsupported with this configuration. Please use print to video." I tried this and it spent some time "conforming" video then it looked like it was recording (I could see the video on the monitor on the deck itself) but the tape came out blank.
I'm getting desperate. Please if anyone can help, I'd be very grateful.

Hi, David,
Thanks for looking. I just haven't found the Apple tech support people very helpful. It says in their list of supported products that they DO support both the Sony camera and the Sony deck in question.
The first time I called Apple tech support when I was having problems capturing the footage, the guy I spoke with didn't even ask me anything - he just said it wouldn't be anything to do with the software and would be the deck.
Then I went into my local Apple store and spoke with somebody at the Genius bar who knew FCP. He wasn't really able to give me much information but did suggest I should export the edited scene as a Quicktime movie but didn't seem to be sure of what settings to use. I did try to do that using NTSC anamorphic (I think from memory that was it) but still was unable to print it to tape. Each time I try anything I get a dialog box saying conforming video and it takes five hours or more before I find out each attempt doesn't work. So as you can imagine it's very frustrating.
I spoke with somebody at Sony who was very helpful but didn't know FCP and he suggested I get Apple Tech Support on the telephone and they could do a conference call with Apple, Sony and me to try and sort out the problem. I then called Apple tech support again and the guy I spoke with there just said "we don't do conference calls". He said the only support they give for free is very basic set up support and told me about the Apple Pro option ($199 each time or $799 for a year) but suggested I try the forum first, which I have done.
However, the guy at Sony had suggested I call the next day and speak with somebody there who know FCP and who wasn't there that day. I did that and he has been very helpful and is still being very helpful in solving my problems; even though they don't make the software they are still trying to help with it.
This is what I feel should happen. I spent $5000 on a computer (my sixth Apple computer in my computer buying history), a lot for a single person as opposed to a company, and then more money to buy the software. I feel very strongly that the tech support should be free and that if the person I speak to doesn't know the answer, he should at least say "I don't know, but I will try to find out for you". I feel that the guys at Sony have gone way beyond the call of duty to try and help me.
I appreciate your interest. Thank you.
Marla.

Capture from Sony HVR-Z1U

Similar Messages

Maybe you are looking for