Capturing live footage and FCE is trying to locate timecode breaks

Hey,
I am using my FCE to capture live footage from each event that I have. I recently started to have a problem with FCE trying to locate time code breaks in the capture, which pauses the capture each time which is footage that I can't get back.
Is there some way to turn that off? I have been forced to use iMovie recently because of this problem but I really need to figure out why this problem would all of the sudden start to appear. Like I said it has worked fine for over a year and now all of the sudden it no longer works.
Please let me know your suggestions.
Thanks

There are only two DV Converter presets in the list. I don't where thelaw3 is so I don't know how your converter box is set up so I can't tell which you should select. It's either PAL or NTSC. You need to read the manual for your converter box and look through the FCE manual.

Similar Messages

HT4623 Can you remotely access your ipad? my ipad was stolen and I'm trying to locate it

Can you remotely access an ipad? My ipad was stolen and I'm trying to locate it.

use find my iphone app, i think u can track ur stolen ipad
i hope u will find ur ipad....
god will help the right

Capturing issues-audio sample rate & locating timecode break

I am a first time FCP user.
I am working on an educational video with hours of DV source tapes.
The source tapes are from a 2R50MC Cannon mini DV camcorder also used as the deck I am capturing from via firewire. My scratch disk is Maxtor III 500GB external drive hooked up via a firewire (I'm realizing the firewire is years old could that be a problem?)
In my first capture test I captured 1 minute of tape by setting in and out points and after completeing the capture I received an error message—"The audio sample rate of one or more of your captured media files does not match the sample rate on your source tape. This may cause the video and audio of these media files to be out of sync. Make sure the audio sample rate of your capture preset matches the sample rate of your tape."
For the past day I have been scouring the user manual, this discussion group and training tapes from Lynda.com and can not resolve this issue. I have determined that the source tape is 12 bit or 32 kHz and yet can not find a way to set up capture preferences to 32 kHz. Is this the problem/resolution? Page 320 of the user manual shows the QuickTime Audio Settings dialog box but I can't find it in FCP or Quicktime. Is this where I make the change to 32kHz?
After doing the first test, I tried again and ran into a new problem—it stopped capturing with the message: Locating timecode break [press esc to abort]. It never seemed to resume capturing and I pressed escape to abort. If I'm reading FCP time code window correctly I received this time code break message within a section I had already captured previously (with the audio sync warning).
I have done several capture tests at different points in the tape and on different tapes all with the same results. I've used the capture clip and capture now buttons. I've tested with drop frame turned on and off. Confirmed my setting of: At timecode break "Make New Clip." Confirmed my Easy Setup as DV-NTSC. My capture preset is DV NTSC 48 kHz. I've turned off and on FCP. Restarted my computer. Restarted my computer with the shift key down and ran permissions.
Any ideas are GREATLY appreciated, T.

I am concerned about available memory when capturing to my hard drive and the babysitting and extra steps involved considering the amount of tape I want to capture...but it does work that's GREAT!
This is always a concern, but in your case I think having the camera and external on the same bus was causing your problem. You may have to capture a little and then transfer, rinse and repeat. Just don't try to do too much at once and let your System Drive get too full, you'll run into other problems there. Slow and steady is the pace!
I shouldn't have stacked my questions since you answered one and Chris answered the other. Don't know how to apply the answered question and who gets the points.
No problem, just mark it answered and divide up the solved and helpful points as you wish. All in all we really don't care too much about the points, but they do make us feel good! Thanks for your desire to use the forums properly.
K

FCE - LOCATING TIMECODE BREAK - Why? Help please

Hello!
I'm trying to capture a video from camera miniDV.
I select "CAPTURE NOW" but after few seconds (when a scene changes), appears this error :
LOCATING TIMECODE BREAK
http://img535.imageshack.us/img535/7316/schermata20100426a11402.png
My settings are these :
http://img202.imageshack.us/img202/3125/schermata20100426a11502.png
Please help me...
Thanks bye

Timecode breaks could be caused by:
1. Actual timecode breaks on the tape.
2. Dirty heads in the playback system.
3. Bad Firewire cable.
4. Capturing to a USB hard drive
5. Capturing to an improperly formatted hard drive
6. Capturing while an anti-virus program is running
If you're using Capture Now, try setting FCP's Device Control to Non-Controllable Device.
-DH
Message was edited by: David Harbsmeier

How can I capture live video and still image by a DirectX compatible USB webcam using LabView ?

Dear forum members
   I'd like to design a user interface which shows a live video and capture still images for it by a DirectX compatible USB webcam using LabView or NI Vision Toolkit, how can I do this ? and If this is possible How can I reach the webcam DirectX filter properties and set them using LabView ? I would be grateful to anyone Who lead me to the correct solution.
    Sincerely
    Cem DEMiRKIR

Cem,
    With our example programs you can acquire and save an image (IMAQ >> File Input and Output >> Snap and Save to File.vi) from one camera, if you double the VI's to create the image and the image task, you can easily have one program acquire and save for two cameras.
    I may need more information on what you mean by calibration. Do you mean basic camera setup? That can be done in Measurement and Automation Explorer by setting up the options within the IMAQ settings for each camera. Or do you mean more complex calibration for special types of images? The more description of what you mean, the better I will be able to help you get it done. You mentioned zoom and motion parameters, what kind of motion? Our vision drivers only control triggering the camera to acquire, then analyzing, processing and displaying the resulting image.
    If you have more details on exactly what you want to do, that would be great. Let me know if you have more questions, thanks!
-Allison S.
Applications Engineering
-Allison S.
Calibration Services
Product Support Engineer

Why does Premiere 7.0 crash when capturing LIVE video and audio?

Why does Premiere 7.x Creative Cloud Crash when capturing live Video in about 10 minutes.

More information needed for someone to help... please click below and provide the requested information
-Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840

A few seconds into capturing "Locating timecode break" comes up

I have just installed FCE on my computer. I use a sony DVCAM deck. There are no TC breaks. I've tried many different tapes and tried a sony Z1 camera to play rushes but same thing happens.
Initially "Dropped frames were detected during the last capture attemp" happened with every tape within a few seconds. I turned this off. Now, within a few seconds of pressing "capture now" or through capturing a clip, the FCE starts locating TC breaks. I've tried leaving it to it, but it starts locating another TC break within a few seconds.
I've tried shutting down the computer and pulling out the cables.
I can view the rushes fine, but the visuals don't play propely when in capture mode.
Hope you can help. Thank you

Hello. I've followed the intructions on the link you gave. Computer is Mac OS X version 10.4.10; Processor 800 MHz PowerPC G4; Memory 768 MB SDRAM; Sartup Disk Macintosh HD
I'm using a LaCie disk as a hard drive. A professional Sony DVCAM deck is connected to the computer through a fire wire.
I'm using FCE version 3.5.
What else do you need to know?
Thank you for your time

I am trying to capture Live footage in Premiere

We are using 5 panasonic hpx500's that are being routed through extron boxes to resize the image to 720x480 prior to running into the switcher. I dont think thats relevent but want you to have all the info. after the switcher we send a second output to a computer. it is runing into a black magic hd extreme box in the back of my mac desktop and im using final cut to record the feed. I then open premiere and edit the services.
I want to stop using final cut and do all of my capturing and editing inside of premiere but i cant get adobe to recognize the black magic box.
Anybody know how to make that happen?
Thank you for your time,
Joshua Wilson
[email protected]

Joshua.Wilson.Vwcaz wrote:
We are using 5 panasonic hpx500's that are being routed through extron boxes to resize the image to 720x480 prior to running into the switcher. I dont think thats relevent but want you to have all the info. after the switcher we send a second output to a computer. it is runing into a black magic hd extreme box in the back of my mac desktop and im using final cut to record the feed. I then open premiere and edit the services.
I want to stop using final cut and do all of my capturing and editing inside of premiere but i cant get adobe to recognize the black magic box.
Anybody know how to make that happen?
Thank you for your time,
Joshua Wilson
[email protected]
Hello Joshua,
Please check the info on this page: http://adobe.ly/kyjD6C
It should have the details you were looking for.
If you need more help with this, let us know.
Thanks,
Kevin

HT4929 I recently misplaced my IPod 4G perhaps at a family members home, and I'm trying to locate it. Can this information be sent to me via email, since I'm having trouble meeting system requiirement attempting to downloading ICloud on my PC?

I have a Windows 32bit Vista home premium operating system that I'm trying to use to load ICloud through my account, but having system requirement issues. I have this IPad that I'm using to generate this email, but what I'm really trying to do is register this IPad & an IPod Touch I own and currently misplaced through Icloud so that I can trace the IPod both.
Appreciate the clarity.

I can see that this issue has been quite extensive, and frustrating, and I am so sorry for all that has happened societygirl! I would like to help you work this issue out. Please follow & send me a Direct Message, so I can get your account specifics and help finally bring this to a resolution.
Thank you,
MichelleH_VZW
Follow us on Twitter @VZWSupport

'Locating Timecode Break' while capturing

I got the software update that claimed it would fix the time code break error while capturing using Final Cut Pro. I'm using an AV Converter to do this. These are the setting I have it on, as recommended by the directions on the box the converter came in.
Device Control: Firewire NTSC
Capture.input: DV NTSC 48 kHz
Time code break usually occurs at around one minute, sometimes much later, other times almost instantly. I've got a legit copy of Final Cut Studio 2, and my converter always worked fine when I used it with Final Cut Express. Tried cleaning tape heads, but that didn't seem to have any effect. I'm open to any suggestions at this point, and I'm hoping it's just something simple that I might be overlooking.

check the following:
you are capturing to an external drive and not the sytem drive
capture settings for non-controllable device
correct version of Quick Time for your combination of FC Pro and Mac OS
the analogue to Firewire box settings (if any) are set to NTSC, for Firewire output and analogue input and set to composite or Y/C as appropriate

ISight Capturing Live Video

hi all,
I just got a macbook with a built in isight camera. The isight works fine for photobooth and iMovie. The problem i have is capturing live footage. I'm unable to have a video chat on ichat. Also, i tried using it on ustream.tv. It doesn't work. I changed the settings on the adobe flash player but it still didn't work. So, I think the problem is capturing live video.
please help! It's frustrating me
Thanks,
Labze89

Thanks for clearing that up, Labze89
Based on that info, your iSight can certainly capture live video.
Ustream identifies itself as a beta site, so you should expect to encounter some problems, but you should be able to resolve them.
Good quality streaming video requires broadband speed. More info below on this subject. Contact your ISP if you need to purchase additional speed (bandwidth.)
Streaming live video also involves proper settings for your modem (and router, if you have one). If you have not recently rebooted (shut down for about a minute and then restarted) your modem and router, do so now. Be sure to let the modem's self-test finish before starting the router. Let the router's self-test finish before restarting your Mac. Rebooting sometimes is all that is required. If restarting does not correct your problem, you will need to consider other possibilities.
At least for users in the USA, enabling your router's "UP-n-P" setting is often all the router configuration that is required. However, sometimes manual port configuration is required. If so, the instructions for your router will give you the info on how to check and change the settings. What setting values you must use will come from the service (Ustream or iChat) you want to use.
If you have enabled your Mac's System Preferences > Sharing > Firewall, enabling your router's "UP-n-P" setting may allow you to stream video without additional configuration of your Mac's Firewall. If the problem persist when your Mac's Firewall is set to "On" and your router's (if you use one) UP-n-P setting is enabled, you may need to configure the necessary ports on your router and in your Mac's Firewall. Search "Help" on your Mac or see this link for Mac OS X 10.4 Help: Setting advanced firewall options.
Also, your ISP must not be blocking any ports required by the service you are attempting to use. See the ustream.tv FAQs for help on your ustream.tv problems. For your problem with streaming video, check FAQ #s 9, 7, and 15 first.
To minimize possible conflicts, disconnect all unnecessary A/V peripherals (such as eyeTV, game consoles, iPods, etc.) and quit all other applications while troubleshooting your problem. You can try adding them back one at a time once you can make your streaming work reliably.
If these and the other FAQs do not help you resolve your ustream.tv problems, and if you do not get help from some other Ustream user here, click ustream.tv's Contact Us link for email help directly from the people who determine how the site works. They should be your best source.
<hr width="85%">
If you use dial-up, or if your broadband speed is not fast enough, iChat AV will also have video problems.
The Mac OS X 10.4: iChat AV system requirements show all requirements for using iChat AV. For instance, you will not be able to use iChat's video if you do not have at least 100 Kbps broadband both up and down. You can test your internet service's uplink and downlink speed (bandwidth) at Speedtest.net.
If you need to post back for more iChat AV help, please confirm that your system meets all system requirements and list your uplink and downlink speeds in your response.
Jim
PowerBook 1.67 GHz Mac OS X (10.4.10) G5 DP 1.8 External iSight

Can u capture live right to mac

i want to know if i can set up my mac to capture live footage of my gl2 with out having to go to tape? any suggestions

Just remove the tape from the camera and you should be good to go. The tape mechanism recognizes when a tape is loaded and will shut off after ~5 mins idle time to protect the tape & heads; no tape, no shutoff. Works in most miniDV camcorders.

Recording Live Footage Straight Into Final Cut X

Does any know the reason why Final Cut X is not capturing my live footage straight from the camera? It is showing me the image but not saving it to my project.

I think it can only capture live footage via Firewire equipped cameras, which basically means the old DV tape camcorders.
If you are using a DV/HDV tape camera you will also probably find that you have to have a tape in the camera and start the camera recording before FCP X will accept the live video . . . which is not a bad thing as you will also end up with a backup copy on tape should anything go wrong with the import.
You can always re-use the tape later.

Are there any benefits to using optimized media when capturing SD footage?

I am going through old MiniDV tapes and I have to say, going through my first project using FCPX has been very good. I have made use of proxy media, but I wanted to see if anyone might weigh in on if creating optimized media is a good idea with SD footage.
And my question might be answered with a bit of a better understanding of what optimized media is. The way I understand it is that the footage is of the same quality of raw footage but much less smaller in filesize (megabytes wise.) Is that correct? In that case, if I capture footage and check the optimized media box, does it capture raw footage and then also create optimized media?
Many thanks!

Nope, DV footage wouldn't benefit from Optimized. Optimized Media is designed for formats that are not especially well-suited to editing, such as AVCHD or H.264- mostly because these formats are more optimized for in-camera use and don't hold up as well to multiple generations in editing. Plus they require much more CPU power to decode and playback.
DV doesn't have these issues as much, is ideally suited to editing and so wouldn't benefit. Proxy mode on the other hand would help a little as it knocks down the file size and amount of processing power. But to be honest the difference in file sizes and CPU requirements between Proxy and DV in standard definition are so minimal that personally I wouldn't bother to use it. Stick with pure DV.

Unable to locate timecode in batch capture

Hi there, I have been working on this problem for a while and would really appreciate some help.
I have a documentary project I have been working on for some time and have completed the EDL. I am now trying to batch capture the footage again in full res and am having problems with a couple of the tapes.
First the specs:
The video was shot on a Sony HDR-HC1 in HDV(1080) mode.
I am using this camera to capture the footage.
I am trying to recapture the footage in a sequence with the easy setting on HDV1080i50.
I had originally captured the footage in SD on an older version of final cut pro (I am now working with FCP6) and didn't realise that my 16:9 footage was actually all 4:3 letterboxed. To fix this problem I used the media manager to export and then in the new project batch capture all the footage again from the tape. The project uses 18 tapes, 16 of which were batch digitised with only minor troubleshooting required. However 2 of the tapes are proving to be very problematic. It seems that whatever clip I select on the tape it gives me a message saying "unable to locate timecode".
I have tried setting the tape to the exact location of the clip before selecting the batch capture, but the computer always seems to look for a spot which is 2-3 mins out of sync with the clip. For example, if the in point is 00:10:00:00 the computer will roll the tape to around the 00:12:00:00 mark and start jogging around there for about 30 seconds until eventually giving me the "unable to locate timecode" message. Looking in the information in the bins, the in and out points are accurate, its just that when I try to capture, the computer rolls the tape to the wrong position.
If anyone knows a workaround for this that will help me avoid having to edit the footage all over again I will be extremely grateful.
Thanks
Liam

HI I have the same problem, the capture window says: Waiting for time code, the device must set in vcr mode and then This operation could not be complete as there is no video, the F!#!%$$ problem is very illogical ,at this mooring I do batch capture without a problem but since the second tape this problem starting, I update to FCP 6.0.4 and,. @@#%#@%#$ the first tape capture but the second not capture and the problem starting againd, note that IMOVIE capture the tape and work very well, iI replace fire wire, camera VCR and , I trayu with Canon, Sony, JVC and the problem persist , I have quicktime 7.4.5, FCO 6.0.4, note that I have two Macs with the same problem in both macs IMOVIE work like a PRO edition Software but FCP is very bad, I have with this problem a long time, I formated Mac, reinstall FCS2 many timers and the problem persist. IS not a problem whit easy setup or wherever , I download the FireWire SDK from Apple and test all connection with the applications of sdk and in all case , the camera and the fire wire are OK, the problem is with quicktime and FCP, If any one is working OK with FCP and DV NTSC devices and JVC PRO HD devices, please tell us HOW DO. I'm working with FCP since 2000 and in this month FCP makes me very UNHAPPY.

Capturing live footage and FCE is trying to locate timecode breaks

Similar Messages

Maybe you are looking for