Capturing sound card audio

Is it possible to capture audio being played through your computer's sound card? I used to do this all the time with Audition 2, but right now I've only got Soundbooth CS4 (at work) and CS5 (at home). Thanks!

BSE,
Yes, Video Editor is a full Audigy 2 ZS soundcard as well as a video capture device - there are two circuit boards in the box. You can capture stereo uncompressed audio into the Line In and SPDIF inputs just like any Audigy. The video portion has its own separate audio inputs.
-Chris

Similar Messages

Sound Cuts Out During Playback-Sound Card/Audio Interface Necessary?-

I'm a voiceover artist with the following setup:
Sennheiser MKH 416 P48 U3 Microphone
Yamaha HS80M Reference Monitors
Mackie Onyx-i 1220 Mixer
Adobe Audition CS6
Dell Inspiron 1720 laptop (Intel Core2 Duo, CPU T5750 @ 2GHz, 32-bit)
Until recently, I could hear anything I recorded or pre-recorded items with no issues. However, now, as I listen to anything, the sound 'cuts out' (latency issues?). The meters on Audition will still be moving, but I'll get no sound from my monitors. I upgraded to Windows 7, hoping and thinking this would solve the issue, and that Audition would play nicely with Windows 7. This 'solution' seemed to have helped, but ultimately, it did not resolve my issue. At this point, I believe it's my sound card. My studio quality setup seems to be too much for my consumer grade sound card. Because my Mackie has an interface built into it, I did not believe that I needed an interface. However, I'm beginning to question that. So, that's part of my question. Is an audio interface necessary for me even though I have one built into my Mackie? If so, based on what I list for my system, does anyone have any recommendations for interfaces? If I do not need an interface, I'd appreciate any suggestions or ideas as to what's causing the sound to 'cut out' and how to resolve it. Any and all help, I thank you for it in advance!
E

Finally! I wrote a reply a few hours back but the fine folks at Adobe took the site down just before I hit send! Lucky I saved it elsewhere because the "recovered post" was only the first couple of paragraphs.
Anyhow, take 2.
Well, first off, your Mackie Onyx mixer has a firewire interface built in so it, in effect, becomes your sound card. The one in your computer isn't involved in the recording/playback process at all (at least not unless you're trying to do something like monitor via the computer card rather than the mixer). Therefore, buying another sound card/interface won't help at all.
Similarly, audio dropouts aren't a latency issue, at least not directly. Latency is the delay in the audio as it does the round trip via you sound interface (mixer) and computer. It's more of an issue for musicians trying to be beat accurate as they over dub tracks. However, the latency controls could be affecting your drop out problem. The latency control in Audition is effectively controlling the buffer size--and having a larger buffer (which increases latency) also gives you playback more protection against glitches when your computer gets busy doing something else. So...the first thing to try is increasing the latency/buffer size on the Edit/Preferences/Audio Hardware menu.
Another thing to check is that you're using the latest drivers from Mackie--check their site and download/install the latest if there are some available. If there's a choice, go for ASIO drivers rather than MME if there are some available.
Also, I mentioned your computer getting busy with other things--for serious sound work shut down everything else on your computer. Pay special attention to networking, wifi, and anti virus software, all of which are usualy prioritised to grab processor cycles over your sound work. Also make sure you shut down all system sounds.
Hope at least one of these suggestions works for you.

Audio capture (recording) from sound card doesn't work

I have a Asus Xonar DS sound card that uses CMI8788 chip, AV200 kernel driver and snd-virtuoso kernel module. The card is recognised on installation (i686) and there are no issues with the sound output.
This is a new installation to try to fix the (lack of) recording problem. I know the card can be used to capture sound being played from a web browser, Youtube and internet radio, as I previously had it working with audacity, gnome-recorder and mhwaveedit, but some months ago, after an upgrade it stopped working.
Alsamixer shows the card as AV200 and I have toggled all the capture options and raised levels to no avail.
The card is not broken as the capture works fine on Kubuntu and even Win7. I have tried pasting asound.state from Kubuntu but there was no diference.
Does anybody know a good troubleshooting guide that deals with the capture side, not output.

"volume: can't open /dev/mixer " is for the users who use OSS so there; you should find out what uses OSS and change it if it is possible and not solely on oss.
and the error I am having is because I defined the specific software to hwd:0,0. so what i should do is to check my softwares and set the audio output to "default"
So in another word use you sound card and in output option of your sound card choose "default over hwd:0,0"

Can JMF capture audio from sound card?

I want to know if JMF can capture sound/audio from the sound card. Until now we have been capturing audio from microphone. but is there any possibility of capturing audio from sound card using JMF.
The audio captured from the sound card is to be streamed using JMF/RTP API.

Dear seniors,
i have tried to display my audio file as a graph as
x axis being the Time and the y axis beeing the frequency/pitch.
look at this post, i have mentioned all here...
http://forum.java.sun.com/thread.jspa?messageID=3073027&#3073027
is it possible to display as i desired?
wht the audio stream has? is it frequency or pitch?...
pls do give me some tips on that...
thanx in advance
-Munas.

Capturing audio from sound card

Hi everybody, I need to record the output from my sound card, I've investigated and I've just found how record sound from the microphone and I don't need this ..... I hope somebody helps me ...
thanks

Dear seniors,
i have tried to display my audio file as a graph as
x axis being the Time and the y axis beeing the frequency/pitch.
look at this post, i have mentioned all here...
http://forum.java.sun.com/thread.jspa?messageID=3073027&#3073027
is it possible to display as i desired?
wht the audio stream has? is it frequency or pitch?...
pls do give me some tips on that...
thanx in advance
-Munas.

Capture audio from sound card

Is there a way to capture the sound from a sound card, but
not the microphone?

Please see this post for response.
Moved discussion to the Desktop Development forum.
Chris

Capture iphone camera with external sound card

i have a recording studio
and i want my video captures to be recorded when the audio is recorded thru my proffessional sound card. can i do that?
thanks

you can take the output of your audio mixer and run it into the headphone jack on the iPhone and it will use that as the audio for your video recording.

Pulse Audio no longer detecting sound card; ALSA still detects

After a recent update, pulseaudio has stopped detecting my sound card. ALSA still detects my soundcard, and I was able to find the following in the verbose output of starting pulseaudio.
D: [pulseaudio] reserve-wrap.c: Successfully acquired reservation lock on device 'Audio0'
I: [pulseaudio] (alsa-lib)utils.c: could not open configuration file /usr/share/alsa/ucm/HDA Intel/HDA Intel.conf
I: [pulseaudio] (alsa-lib)parser.c: error: could not parse configuration for card HDA Intel
I: [pulseaudio] (alsa-lib)main.c: error: failed to import HDA Intel use case configuration -2
I: [pulseaudio] alsa-ucm.c: UCM not available for card HDA Intel
When I check out the ALSA directory mentioned, it turns out to indeed be the case that the entire ucm directory does not exist
[root@ArchSpiron james-arch]# ls -lah /usr/share/alsa/
total 52K
drwxr-xr-x 2 root 4.0K Apr 14 14:56 pcm
drwxr-xr-x 7 root 4.0K Apr 14 14:56 .
-rw-r--r-- 1 root 9.0K Apr 14 14:12 alsa.conf
drwxr-xr-x 2 root 4.0K Apr 14 14:12 alsa.conf.d
drwxr-xr-x 208 root 4.0K Apr 13 15:37 ..
drwxr-xr-x 2 root 4.0K Apr 11 07:20 init
drwxr-xr-x 2 root 4.0K Apr 11 07:20 speaker-test
drwxr-xr-x 3 root 4.0K Jan 23 21:21 cards
-rw-r--r-- 1 root 523 Dec 29 21:33 bluetooth.conf
-rw-r--r-- 1 root 155 Dec 18 22:34 smixer.conf
-rw-r--r-- 1 root 3.2K Dec 18 22:34 sndo-mixer.alisp
Instead the configuration file it's looking for exists under the cards/ directory
[root@ArchSpiron james-arch]# ls -lah /usr/share/alsa/cards/
total 264K
drwxr-xr-x 3 root 4.0K Apr 14 14:59 .
drwxr-xr-x 7 root 4.0K Apr 14 14:56 ..
-rw-r--r-- 1 root 4.6K Apr 13 16:20 HDA-Intel.conf
-rw-r--r-- 1 root 1.4K Apr 13 16:20 aliases.conf
-rw-r--r-- 1 root 7.0K Apr 12 08:10 USB-Audio.conf
drwxr-xr-x 2 root 4.0K Jan 23 21:21 SI7018
-rw-r--r-- 1 root 669 Dec 18 22:34 AACI.conf
-rw-r--r-- 1 root 302 Dec 18 22:34 ATIIXP-MODEM.conf
-rw-r--r-- 1 root 2.2K Dec 18 22:34 ATIIXP-SPDMA.conf
-rw-r--r-- 1 root 2.4K Dec 18 22:34 ATIIXP.conf
-rw-r--r-- 1 root 437 Dec 18 22:34 AU8810.conf
-rw-r--r-- 1 root 159 Dec 18 22:34 AU8820.conf
-rw-r--r-- 1 root 520 Dec 18 22:34 AU8830.conf
-rw-r--r-- 1 root 5.7K Dec 18 22:34 Audigy.conf
-rw-r--r-- 1 root 7.5K Dec 18 22:34 Audigy2.conf
-rw-r--r-- 1 root 2.3K Dec 18 22:34 Aureon51.conf
-rw-r--r-- 1 root 2.5K Dec 18 22:34 Aureon71.conf
-rw-r--r-- 1 root 3.8K Dec 18 22:34 CA0106.conf
-rw-r--r-- 1 root 1.8K Dec 18 22:34 CMI8338-SWIEC.conf
-rw-r--r-- 1 root 1.9K Dec 18 22:34 CMI8338.conf
-rw-r--r-- 1 root 2.1K Dec 18 22:34 CMI8738-MC6.conf
-rw-r--r-- 1 root 2.9K Dec 18 22:34 CMI8738-MC8.conf
-rw-r--r-- 1 root 1.6K Dec 18 22:34 CMI8788.conf
-rw-r--r-- 1 root 2.9K Dec 18 22:34 CS46xx.conf
-rw-r--r-- 1 root 5.5K Dec 18 22:34 EMU10K1.conf
-rw-r--r-- 1 root 2.7K Dec 18 22:34 EMU10K1X.conf
-rw-r--r-- 1 root 1.4K Dec 18 22:34 ENS1370.conf
-rw-r--r-- 1 root 1.8K Dec 18 22:34 ENS1371.conf
-rw-r--r-- 1 root 152 Dec 18 22:34 ES1968.conf
-rw-r--r-- 1 root 4.3K Dec 18 22:34 Echo_Echo3G.conf
-rw-r--r-- 1 root 1.2K Dec 18 22:34 FM801.conf
-rw-r--r-- 1 root 333 Dec 18 22:34 FWSpeakers.conf
-rw-r--r-- 1 root 672 Dec 18 22:34 FireWave.conf
-rw-r--r-- 1 root 217 Dec 18 22:34 GUS.conf
-rw-r--r-- 1 root 2.1K Dec 18 22:34 ICE1712.conf
-rw-r--r-- 1 root 2.8K Dec 18 22:34 ICE1724.conf
-rw-r--r-- 1 root 192 Dec 18 22:34 ICH-MODEM.conf
-rw-r--r-- 1 root 3.0K Dec 18 22:34 ICH.conf
-rw-r--r-- 1 root 2.8K Dec 18 22:34 ICH4.conf
-rw-r--r-- 1 root 558 Dec 18 22:34 Maestro3.conf
-rw-r--r-- 1 root 4.7K Dec 18 22:34 NFORCE.conf
-rw-r--r-- 1 root 657 Dec 18 22:34 PC-Speaker.conf
-rw-r--r-- 1 root 486 Dec 18 22:34 PMac.conf
-rw-r--r-- 1 root 705 Dec 18 22:34 PMacToonie.conf
-rw-r--r-- 1 root 1.2K Dec 18 22:34 PS3.conf
-rw-r--r-- 1 root 780 Dec 18 22:34 RME9636.conf
-rw-r--r-- 1 root 780 Dec 18 22:34 RME9652.conf
-rw-r--r-- 1 root 1.5K Dec 18 22:34 SB-XFi.conf
-rw-r--r-- 1 root 2.2K Dec 18 22:34 SI7018.conf
-rw-r--r-- 1 root 1.7K Dec 18 22:34 TRID4DWAVENX.conf
-rw-r--r-- 1 root 1.2K Dec 18 22:34 VIA686A.conf
-rw-r--r-- 1 root 2.7K Dec 18 22:34 VIA8233.conf
-rw-r--r-- 1 root 2.8K Dec 18 22:34 VIA8233A.conf
-rw-r--r-- 1 root 2.5K Dec 18 22:34 VIA8237.conf
-rw-r--r-- 1 root 830 Dec 18 22:34 VX222.conf
-rw-r--r-- 1 root 839 Dec 18 22:34 VXPocket.conf
-rw-r--r-- 1 root 1.5K Dec 18 22:34 VXPocket440.conf
-rw-r--r-- 1 root 1.4K Dec 18 22:34 YMF744.conf
-rw-r--r-- 1 root 687 Dec 18 22:34 aliases.alisp
I'm not at all familiar with pulseaudio configuration. Does anyone know of a good way for me to resolve this issue? Have I even identified the correct issue?
UPDATE:
I was able to work around my problem for the moment by symlinking the configuration file to the location that pulseaudio was actually looking for it
# mkdir -p /usr/share/alsa/ucm/HDA\ Intel
# ln -s /usr/share/alsa/cards/HDA-Intel.conf /usr/share/alsa/ucm/HDA\ Intel/HDA\ Intel.conf
Although this does get my sound back, it is a hacky work-around and obviously not ideal. Anyone who knows a bit about pulse configuration, I welcome your input here
Last edited by OakRaider4Life (2013-04-14 22:14:34)

Thank you so much for posting your solution!
I was having the same problem. The funny part was it started happening (and not always) after KDE says that the Intel HDA device is "gone" and asking me to remove it from my configuration. Even by saying no it wouldn't work. Killing pulseaudio with
pulseaudio -k
would have everything fallback to Alsa but starting pulseaudio again wouldn't work.
Rebooting right away doesn't take care of the issue either but after a while the problem would go away...
Any inputs would be appreaciated!

Added sound card, no onboard audio no more

i added an sb live value for the use of the joystick port only, not wanting to use ti as a sound card. the onboard audio of my 865pe neo2 fis2r msi 6728 no longer works. so how can i get back my onboard audio? my speakers are still plugged into the onboard. is this even posible? to use onboard audio, but use my joystick on the sb live card when playing games? or is it only one or the other? do i need to go into the bios maybe and tell it to use onboard audio? like maybe it changed cus of the new sb live value card?
ok, i hooked up my speakers to the sb live card, it's fine i guess , but is it possible to use onboard audio with joystick port only from the live card? or because i have a sound card installed now, does that totally disable onboard completely unless i removed the live card?

Yep No is the Answer, Because as soon as Windows Sees that you have a PCI sound card, it will not allow the Onboard sound chips Drivers to Load upon Bootup, I cant believe that you went through the Trouble of Installing a Sound Card that has a "MIDI" port, Instead of just Getting a USB Joystick , as the New USB Joysticks are Much more Responsive and Support Many More Games, and You can Get one For Less $ then you Paid for the Soundblaster .....Sean REILLY875

ALSA is not detecting my M-Audio Delta 1010 sound card (x86-64)

Hi
I've been searching Arch forums and googling for my problem but I can't find a suitable answer.
I installed my M-Audio Delta 1010 sound card on this PC but ALSA doesn't get it to work.
Chipset envy24 / ice1712
On dmesg I find:
$ dmesg | grep -i ice1712
[ 8.135832] snd_ice1712: probe of 0000:05:06.0 failed with error -5
However, it is listed on lsmod:
$ lsmod | grep '^snd' | column -t
snd_hda_codec_hdmi 24529 4
snd_ice1712 59590 0
snd_cs8427 6970 1 snd_ice1712
snd_i2c 4107 2 snd_ice1712,snd_cs8427
snd_ice17xx_ak4xxx 2437 1 snd_ice1712
snd_ak4xxx_adda 8070 2 snd_ice1712,snd_ice17xx_ak4xxx
snd_hda_codec_realtek 61420 1
snd_ac97_codec 113344 1 snd_ice1712
snd_mpu401_uart 5980 1 snd_ice1712
snd_hda_intel 26181 5
snd_hda_codec 98034 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_hwdep 6429 1 snd_hda_codec
snd_rawmidi 18800 1 snd_mpu401_uart
snd_seq_device 5269 1 snd_rawmidi
snd_pcm 75735 5 snd_ice1712,snd_ac97_codec,snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 7218 2 snd_pcm,snd_hda_intel
snd_timer 18935 1 snd_pcm
snd 60189 25 snd_ice1712,snd_hda_codec_realtek,snd_ac97_codec,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_i2c,snd_pcm,snd_rawmidi,snd_hda_codec,snd_ak4xxx_adda,snd_hda_intel,snd_mpu401_uart,snd_seq_device,snd_cs8427
I followed some instruction and created a alsa-base.conf file with:
$ cat /etc/modprobe.d/alsa-base.conf
options snd slots=snd_ice1712,snd_hda_intel
options snd_ice1712 index=0
options snd_hda_intel index=1
aplay -l returns:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: SB [HDA ATI SB], device 0: ALC889 Analog [ALC889 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 1: ALC889 Digital [ALC889 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
Seems card 0 is reserved for the m-audio card but is not being detected by ALSA
envy24control also exits with:
$ envy24control
No ICE1712 cards found
Finally, my /dev/snd
$ ls -l /dev/snd
total 0
drwxr-xr-x 2 root root 80 Dec 7 20:25 by-path
crw-rw----+ 1 root audio 116, 7 Dec 7 20:25 controlC1
crw-rw----+ 1 root audio 116, 16 Dec 7 20:25 controlC2
crw-rw----+ 1 root audio 116, 6 Dec 7 20:25 hwC1D0
crw-rw----+ 1 root audio 116, 15 Dec 7 20:25 hwC2D0
crw-rw----+ 1 root audio 116, 14 Dec 7 20:25 hwC2D1
crw-rw----+ 1 root audio 116, 13 Dec 7 20:25 hwC2D2
crw-rw----+ 1 root audio 116, 12 Dec 7 20:25 hwC2D3
crw-rw----+ 1 root audio 116, 5 Dec 7 20:26 pcmC1D0c
crw-rw----+ 1 root audio 116, 4 Dec 7 20:26 pcmC1D0p
crw-rw----+ 1 root audio 116, 3 Dec 7 20:26 pcmC1D1p
crw-rw----+ 1 root audio 116, 2 Dec 7 20:25 pcmC1D2c
crw-rw----+ 1 root audio 116, 11 Dec 7 20:27 pcmC2D3p
crw-rw----+ 1 root audio 116, 10 Dec 7 20:26 pcmC2D7p
crw-rw----+ 1 root audio 116, 9 Dec 7 20:26 pcmC2D8p
crw-rw----+ 1 root audio 116, 8 Dec 7 20:26 pcmC2D9p
crw-rw---- 1 root audio 116, 1 Dec 7 20:25 seq
crw-rw----+ 1 root audio 116, 33 Dec 7 20:25 timer
$ ls -l /dev/snd
total 0
drwxr-xr-x 2 root root 80 Dec 7 20:25 by-path
crw-rw----+ 1 root audio 116, 7 Dec 7 20:25 controlC1
crw-rw----+ 1 root audio 116, 16 Dec 7 20:25 controlC2
crw-rw----+ 1 root audio 116, 6 Dec 7 20:25 hwC1D0
crw-rw----+ 1 root audio 116, 15 Dec 7 20:25 hwC2D0
crw-rw----+ 1 root audio 116, 14 Dec 7 20:25 hwC2D1
crw-rw----+ 1 root audio 116, 13 Dec 7 20:25 hwC2D2
crw-rw----+ 1 root audio 116, 12 Dec 7 20:25 hwC2D3
crw-rw----+ 1 root audio 116, 5 Dec 7 20:26 pcmC1D0c
crw-rw----+ 1 root audio 116, 4 Dec 7 20:26 pcmC1D0p
crw-rw----+ 1 root audio 116, 3 Dec 7 20:26 pcmC1D1p
crw-rw----+ 1 root audio 116, 2 Dec 7 20:25 pcmC1D2c
crw-rw----+ 1 root audio 116, 11 Dec 7 20:27 pcmC2D3p
crw-rw----+ 1 root audio 116, 10 Dec 7 20:26 pcmC2D7p
crw-rw----+ 1 root audio 116, 9 Dec 7 20:26 pcmC2D8p
crw-rw----+ 1 root audio 116, 8 Dec 7 20:26 pcmC2D9p
crw-rw---- 1 root audio 116, 1 Dec 7 20:25 seq
crw-rw----+ 1 root audio 116, 33 Dec 7 20:25 timer
controlC0 and pcmC0 is not present!
So, what might be causing the probe error -5?
I really need to get this card working! :S
I have Arch up to date!
Hardware specs:
CPU: AMD FX6100
Board: Gigabyte (can't recall the model) with NVidia chipset
Thank you,

I have an m-audio delta 1010lt as well, it's a great card but it sits in my closet now because I "upgraded" to a motherboard that doesn't have legacy PCI slots. However, I'm pretty sure I remember the card working for me and being "plug and play" under arch with kernel 3.3 or newer. So some things I would consider:
Try checking IRQs, make sure nothing is overlapping.
Try using the LTS kernel, to see if it is kernel related, since ice1712 module should ship with almost any kernel => 2.6.26.
How many watts is the power supply? Sometimes insufficient wattage can result in drivers failing to load.
What other sound cards do you have installed? Have you tried blacklisting all of the other cards in your system using alsa-base.conf? This is a bit extreme, but might be a useful troubleshooting measure, as some people have had issues in the past with alsa indexing mutiple cards to the same slot number

Pulse audio no sound card detected

Hello,
I have installed pulse audio according to the wiki but after install and reboot no sound card is detected. My pc is sony vaio VGN-NW21MF and the lspci output for the sound device is following
01:00.1 Audio device: ATI Technologies Inc RV710/730
I don't have alsa installed and try the trouble shooting section in wiki but still don't resolve the problem.Thx for any help. I using gnome and have dbus loaded
Last edited by arturr (2011-01-25 16:41:33)

I am confused have you installed alsa or not?
your first sentence says that you have, your last says that you don't. and your title talks about pulse audio.

Could not detect Sound Blaster Audio Card on xp sp2 Sys

I have Audigy Platinum and trying to install to a recently re-installed windows xp sp2 system. On my previous install everything was working fine and now I am looking to install the newest drivers and the error comes up [color="#ff3300">"could not detect Sound Blaster Audio Card on system". The strange thing is windows recognizes the card and will install it's drivers, but when I go to install the latest driver update I get the error. In addition, I also tried to run the install from my original disk.
I also?un-installed the devices showing? in the windows device manager, then tried and the same error, I even tried it in safe mode. Any ideas?Thanks and Advance,Mikel

Yes i think the real lesson here is not to buy creative,. i have the same problem with their junky card, so i guess ill just have to take buisness somewhere else. if you all do the same perhaps the threat of them going out of buisness will have them deal with their problems. if not atleast we saved others the headache of learning this lesson.

I am getting no signal to my dj mixer using m-audio firewire audiophile sound card connected to my mac book pro using Traktor Dj software can anyone help?

I am getting no signal to my dj mixer using m-audio firewire audiophile sound card connected to my mac book pro using Traktor Dj software can anyone help?
The firewire port reads the dj software and I can hear music playing through the sound card when I plug my headphones into it but there is no signal to the hardware (my dj mixer).
I have reset the firewire by turning off my mac book pro for a few hours and can see the sound card device in the fire wire section after clicking on the apple icon on the top left corner of my mac.
My dj mixer works on another mac computer with the same soundcard and different firewire cable.
Hope someone can help
Thanks
Wayne

kmiddlet88,
yes, it could be due to nearly anything listed in your kernel extensions, startup items, launch daemons, launch agents, or user items above. Please check all of your installed third-party software to make sure that the versions which are installed on your MacBook Pro are compatible with Mavericks; uninstall every software package which isn’t Mavericks-compatible. After you’ve done that, boot into Safe mode, and see if you still get the beach ball of doom there. If it doesn’t appear there, restart normally and see if it appears then.

CUPC - "Phone Error. Could not place call because you have no audio device or sound card."

Periodically throughout the day, CUPC will not make or receive calls, but instead presents a dialog box with the message "Phone Error. Could not place call because you have no audio device or sound card." See attachment.
Signing out of and back into CUPC resolves the issue temporarily.
I have version 8.6.2 installed and I'm using a USB headset.
Does anyone know what might be causing this?

Hi Steve,
I have users reporting this as well with Jabra GN 2000 headsets. They claim using a different headset resolves it which I'm waiting to confirm but I was wondering if you were able to figure this out.
Thanks
Erik

Two versions of Premiere two sound cards when capturing

We are television station and we encode shows that are sent to us on a daily basis. All shows that we get we are licensed to show. We are using Adobe Premiere CS4 to capture the videos as they come to us by way of satellite feed. It works well. We can also work on another project with CS4 while capturing. Problem. Sound. While we are capturing, we cannot test the sound because the capture and the time line work space uses the same sound card. Is there a way that we can set up two sound cards and have the time line work space use one while the capture uses another? Or can we use another version of Premiere, (we also have 2.0), and have that one assigned to a separate sound card so we can edit other shows while we are capturing?

Maybe use OnLocation for the capture process, while using Premiere for the other stuff.

Capturing sound card audio

Similar Messages

Maybe you are looking for