CAPWAP goes down but AP is up
I have a few APs that keep doing this where WCS generates alarms saying that the AP is down and a/b/g interface is all down. If I check the WCS, I see the AP up for more than 10 days or so but the CAPWAP is up only for 4 minutes. Eventually clients associate to that AP but they see downtime.
Is it because the AP is bad (hardware issue)?
CAPWAP Up Time
4 m 17 s
AP Up Time
10 d 0 h 24 m 4 s
Meena
Well based on the uptime we know one thing is for sure. Something interrupted the capwap tunnel between the AP and the WLC and this is what triggered the alarm. And you are correct. Clients will be impacted. The most common thing you will see is that the AP moves from one WLC to another WLC. However, if you are sure this is not the case.
Then something else could have intruped the tunnel.
Down vlan
A number of missed heart beats (between the AP and WLC)
Routing issue
I know... Im strecthing it ... The list could go on ...
shoot me an email of the address. I can shoot over at lunch ...
Similar Messages
-
Admin server is going down, but managed servers are fine.
HI,
Admin server is going after sometime of starting, but nodemanger and managed servers are running fine, I didn't anything in admin.log everything looks fine.
WebLogic Server 8.1 SP4
jrockit81sp4_142_05
Pls let me whats the problem with admin server.Way too little information to go on. What operating system? Are you looking at stdout and stderr for messages? Do any random files show up in the directory in which you started the adminserver (core files, hotspot error files, etc)? Does it occur if you switch to using Sun's JDK? Have you tried undeploying any applications (other than the console, of course) or startup classes from the admin server?
-
Hi there, I'm experiencing some issues with a 1310 LWAPP on a University, here is the scenario:
The AP is directed to some specific classrooms and at a certain point the radio goes down or at least there is no more communication between the clients and the AP, but the association in the computers remain the same for a couple of minutes, after that the link goes down, but the weird thing is that the communciation to the AP via Ethernet remains up. We tested this and the ping's all were responding while the radio was down.
Steps already done:
-A new 1310 has been tested, same results.
-A new power injector, same results.
-The UTP cabling between the power injector and the IDF has been changed, same results.
-The port to which the AP was connected at the IDF switch was changed, same results.
I'm thinking as a possible solution:
-Replacing the coax cabling between the power injector and the AP (not more than 15 ft).
-Ensure the AC voltage at the power outlet is delivered correctly (110v) not less, not more.
I'm wondering if this steps may be causing the device(s) to fail in such a way, because if it is not receiving the appropriate ammount of power the radio module simply goes down, but as the ethernet module requires less power it remains up.
What do you think?
Any recommendation is more than welcomed; too much time has been dedicated without success.
Thanks in advance!For the troubleshooting chech the Red color indicates an overcurrent or overvoltage error condition disconnect input power from the power injector, check all coax cable connections for a possible short, wait approximately 1 minute, and reconnect input power to the power injector. If the LED turns red again, contact technical support for assistance.
The power injector requires approximately 50 seconds to recover from an overcurrent or overvoltage condition.
Off indicates input power is not available verify that the power module is connected to the power injector and that AC power is available or that 12- to 40-VDC input power is connected to the power injector. -
One interface of pair goes down
Hi
If two interfaces are paired into one group and one interface of pair goes down, will the second interface will be declared as down by IPS?Hi,
I I have a problem connected to this issue.
I have only one IPS4270-20 with software 7.0(7)E4 and I use 2 IF pairs on it. Both IF pairs are for the same operation, and they were implemented for HA purposes. We have two 6500 chassis in VSS and all of the IPS ports connected to these switches. Gi3/0-Gi3/1 and Gi1/2-Gi3/3 are in pair, and Gi3/0-Gi3/2 are the inbound and Gi3/1-Gi3/3 are the outbound interfaces, so it achieves the hardwer failover requirements. Inbound IFs creat an Etherchannel, and outbound IFs creat an other Etherchannel, so we try to prevent an L2 loop when VSS breaks.
The issue what I can't solve is the following:
If I shut down the 6500 IF what is connected to the IPS Gi3/0 I would like Gi3/1 to goes down, but it isn't the case.
I tried to use LACP in the Etherchannel, so when Gi3/0 goes down, the 6500 port which connected to the IPS Gi3/1 should be removed from the Etherchannel, but it isn't the case also.
Do you have an idea, what could be the problem, or I should redesign the topology?
Thanks,
Miki -
Please help! I updated safari and yes it is an older desktop, but now all of the sudden tabs I have open will freeze on me. I can see what is going on, but am unable to type anywhere on the page! I have to shut down safari and then open up a whole new window to even attempt to get it to stop! It is driving me insane not to mention I need my desktop to work properly. I beg for someone to help me with this.
Safari 4.1.3 for Tiger can be downloaded here:
http://support.apple.com/kb/DL1069 -
I've had this computer since october of 2013 or so and I have just recently run into this problem. I use the volume keys on the keyboard and I hear the tick sounds and it shows that its going up and down but the volume doesn't actually change. I've looked in the "sound" settings and everythings seems to be correct... I can't adjust the sound in their either though. I pay too much to be having an issue like this.
Possible? Yes. Likely? I'm not sure.
In my house, I would suspect that either one of our pets chewed on a cable or dislodged a connector, or somebody bumped a connection loose, but then I would expect either no volume at all or hum from a grounding problem. Clear, non-zero constant volume is harder to explain.
You say adjusting the output volume directly in the Sound settings or on the menu bar also has no effect on the audible output?
You might want to go ahead and answer the question about connections. Somebody else might come along who recognizes a possible problem with the particular combination you are using. I don't have exactly your model of Mac Pro or display. (Is yours the Apple LED Cinema Display? Which size?) -
I have a 5th Gen iPod Touch. I went in iMessage to save videos that were sent to me in my camera roll. The videos do not appear in my camera roll but my memory keeps on going down. I do not know how to solve the problem. I do not want to restore my iPod but I want to get my memory back. Please Help ME
Connect the iPod to your computer and look at the storage used by the various categories as shown in the colored bargarph in iTunes.
Come back with the results.
An "other" larger tha about 1 1/2 usually indicates that the "other" includes corrupted files.
First try:
"First you go settings/general/usage/music/then left swipe over music and press delete and you would think it deletes your music but it doesn't instead it deletes your other but make sure your ipod is connected to a computer while doing this"
as recommended by:
How do I get rid of "other" storage: Apple Support Communities
Next, usually restoring from backup eliminated the corrupted files. However, sometimes restoring to factory settings/new iPod is required.
To restore from backup see:
iOS: How to back up
To restore to factory settings/new iPod see:
iTunes: Restoring iOS software -
Trying to figure out how to charge my new ipad wi-fi cellar. I plugged it in but instead of going up in % is still going down and its now showing me that its charging like a cell phone does. When I started to charge it, it was 28% now its 27%. Its plugged into a wall.
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
Cheers, Tom -
Space available going down everyday. It should be 1gb or more but now its 80mb only.
My iPhone 5's space is going down daily. I havnt downloaded anything at all.
This happened a month back too so i restored my phone. And restore the backup too.
And at time its was more than 2gb available evem after the sync.
And in a one month time it has gone from 2gb to 70-80mb.
Whats the matter?
Is it something in iOS7 ?
My phone is fully updated.
Please help someone.
And i don't wanna restore the phone again.Only once you know where that information is located, which we don't and EA does. Someone on these boards may happen to know, but even if they do, you've still got a failing installer to troubleshoot, and again, EA knows their installer best.
-
Hi,
I have my DHCP configured in order to deliver the next default gateway, the 52.44.72.254.and all others devices have the same default gateway, the 52.44.72.254.
The Core switch with IP 52.44.72.200 has next route: ip route 0.0.0.0 0.0.0.0 52.44.72.254
The issues comes when I change it to Core switch, everything goes down.
I am adding a new network, we will replace the 52. In the moment we enable the Core in the 10 network with a new default gateway, everything goes down.
Everything should work as today because the VLAN 1, where the 52 is working, keeps as today. We change only the IP for Core sw.
When the network is down, I tracerted the external routes, and all traffic stops in the Core sw.
It looks like If it was routing, but it is not.
Do you have any idea what could happend?
FYI:
interface Vlan1
description VLAN DATOS
ip address 52.44.66.254 255.255.255.128 secondary
ip address 52.44.72.200 255.255.255.0
no ip redirects
ip local-proxy-arp
ip route-cache same-interface
interface Vlan95
ip address 10.106.128.2 255.255.255.0
interface Vlan300
ip address 10.106.130.1 255.255.254.0
interface Vlan301
ip address 10.106.134.1 255.255.255.0
Thanks by your help, best regards. Luis.I dont understand your configuration. What is your next hop device thats defined in your default route? A router? Are you trunking to the router? Is IP routing enabled? More of the configuration of this core and next hop device will be helpful.
-
Help!! I'm using a Mid 2012 MBP retina 2.3Ghz i7 with 8GB of ram 256SSD. for the past 2 years my write speeds has been consistently on 400MB/s and up via black magic test. but now it only have 100MB/s going down to 80MB/s. what should I do???? I have already cleaned and even restored my MBP still it's on 100MB/s. please help. I have to finish tasks on a timely manner.
No. This requires completely repartitioning the SSD. You can do that only by using the Network Recovery method or the method I outlined. My method preserves all your data and doesn't require doing a slow Network Recovery. But if you wish to do that instead. The purpose of the whole exercise is to "clean" the SSD of garbage collected during use that tends to cause the SSD to slow down as you've described.
Install OS X Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Security button. Set Zero Data - one-pass, click on the OK button. Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer. -
I am downloading a 6.4GB game with Safari. Download starts very well, 850KB/s but systematically after 10 or 15mn speed goes down until download stops. Can somebody help please?
systematically after 10 or 15mn speed goes down until download stops
Check with your iSP. There may be a limit to files sizes. -
My battery on my iPad mini isn't charging, the charging sign is on, but the battery just keeps going down.
Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Since you did not say how long the battery lasts I am nut sure the battery is the problem. -
My itunes store balance keeps going down. It said I had $1.20 but when I tried to buy a song it changed to $0.20 and then when I added another $25 card it now says I only have $25.02??
Hello babichanjacob
Change how it syncs by enabling Manually manage music and videos, then you can drag and drop the music that you want on your iPhone. Revert it back to test to see if that resolves the issue.
Managing content manually on iPhone, iPad, and iPod
http://support.apple.com/kb/HT1535
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
My battery shows it is charging but the percent of battery life is going down
When I plug my iphone up to the computer it shows it is charging but the percent of battery life goes down. It won't charge on any of my other chargers either. This is a pretty new phone, not a year old. Have already reset by holding both buttons for 15 seconds and that didn't help.
I think it needs a repair.
Same as you cherge it setted on air (whith all connections disconnected ?)
Maybe you are looking for
-
Hi Everyone, My name is Imran and I currently work for the Government as a support engineer and have been thinking about learning about SAP but i don't really know where to start and was wondering if some one could advise on what courses would be bes
-
Iphone 4s is on 5.0.1 and cant restore
I put my iphone 4s into dfu mode because it crashed. Now i plug it into itunes and it says restore and update. then when it downloads an update it says update is not compatible. But the phone is on 5.0.1 already? Any ideas
-
Importing existing classes loses package identity in 9.0.2
I have tried several ways, but everytime I import existing classes, they all go to Miscellaneous Files and won't display under their packages. This is from disk or from source code control (CVS). This works fine with the same exact classes and direct
-
I had opened iphoto and i couldn'd see my pictures
what is my problem if i open iphoto and i can't see my pictures? And if i want to open one there is a "!" instead of the picture.
-
Autocomplete in internet explorer for a portal
Hello, we are in the process of implementing a new SAP portal, and I would like to know if it is possible to deactivate the autocomplete functionnality in IE (for the login screen of the portal) but only for the SAP portal, not for other websites. We