Card Reader & Screen Brightness Issues with 3000 N100 Running Fedora 10

Hi, I'm new to the forum, and came here to look for info on a couple minor issues I'm having with Fedora 10 on my 3000 N100. It's great to see that there's a group of Linux users here. Anyway, onto the issues:
1) The integrated card reader. It works just as it should right after I boot up - i.e. insert an SD card and it auto mounts. However, if I leave the system idle while doing other things the card reader quits working. I've used the terminal to look up the location of the card reader when it's working properly. If I unmount the card (under the Gnome desktop System menu, right click the card, select unmount), leave it in the reader, and try to remount it in terminal (using the location mentioned above) it tells me the device isn't found, or the location doesn't exist.
2) I've set the screen brightness to max as my default (which is just bright enough to read comfortably under the fluorescent lights here at work), and my brightness function keys work fine too right after bootup. Again, if I leave the system idle for a bit the screen goes dim. At this point the brightness function keys quit working as well. If I go to System > Preferences > System > Power Management I can slide the brightness toggle down and back up, and the screen then immediatetly returns to full brightness.
Any help you folks can offer would be greatly appreciated.

Hi ugaarguy,
It sounds to me like there's some power settings that are powering down the card reader after a certain period of inactivity. This could also be the case for your brightness settings and keys.
You may find a better answer in the Fedora forums regarding these issues, so you might want to try posting there as well.
Is there a control panel which deals with power settings in Fedora? Perhaps check around for these settings to see if there are certain power saving features enabled on your system.
J

Similar Messages

[SOLVED] Screen brightness issues with Acer 5372Z

The screen of my laptop goes black whenever I boot into ArchLinux, after "reading Udev events" on startup. Most of the time I have to use a flashlight to see the console on my screen and type
sudo setpci -s 00:02.0 F4.B=20
to set screen brightness manually. The `Fn` + `Brightness up` combination doesn't work on my machine, but that's not an issue with Arch, but fault to sugar in coffee.
There are a lot of similar threads in this forum, but none of the solutions described there really worked 100% or not at all, that's why I'm opening a new thread as this seems to be specific to my hardware.
Details:
Graphics controller:
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09)
Screen resolution:
1366*766
/boot/grub/menu.lst:
# (0) Arch Linux
title Arch Linux
root (hd0,0)
kernel /vmlinuz-linux root=/dev/sda10 resume=/dev/sda5 ro vga=775
initrd /initramfs-linux.img
/etc/rc.conf#DAEMONS:
DAEMONS=(hwclock syslog-ng network netfs crond laptop-mode dbus gdm)
I will describe here what I have did so far on hacking:
Installed the video driver for my Intel card as described here in the wiki
Set kernel mode to `nomodeset`, without specifying vga, of course, which surprisingly solved the issue, but prevented me from using Gnome.
The supposed solution in the Arch wiki doesn't work for me. It makes it worse, in the sense of dumping screen brightness even before "reading udev events" on boot.
My current workaround (to avoid using a flashlight) is to put this line into my `/etc/rc.local`:
setpci -s 00:02.0 F4.B=20
I wonder if you can help me to solve this issue, or point me to any of the great documentation provided by the Arch community I might have missed...
Last edited by kennym (2011-09-06 16:03:58)

rg_arc wrote:I have this problem as well for my Acer Aspire 4810TZ. The only thing I can think of is to make some sort of temporary fix. But I agree with you, There should be a permanent fix. Every time I've installed Arch on this computer the same problem arises and the only way I can change the brightness is the setpci terminal method.
This is bad news for new Arch (and Linux) users. This will be probably the point where they will turn over to another distribution.
It seems to be something which has been included in newer kernels, because I can remember that in the 2.6 series this issue did not exist.
Last edited by kennym (2011-09-05 16:05:08)

HP Beats Special Edition 15-p030nr Notebook PC (ENERGY STAR) screen brightness issue

I'm haing a screen brightness issue on my HP Beats Special Edition 15-p030nr Notebook PC (ENERGY STAR). I upgraded from 8.1 and the F2/F3 keys to dim or brighten screen do not function. Any suggestions besides reverting back to 8.1.? Not sure if I had the screen dimmed all the way or brightened all the way when it was upgrading, or if it even mattered.

Hi @Twright2014
Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see your having some sound issues with your new notebook. I will be happy to help you with this. How does the audio sound when you use a set of headphones? Try the troubleshooting steps in this HP document No Sound from Speakers which includes using the built-in Windows troubleshooter.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Screen display issue with InDesign CS4 (Windows)

I just upgraded from CS2 to CS4. I can open and use InDesign with no problems, until I try to switch to another application. Then, when I try to go back to InDesign, all I can see is the portion of the bar at the top of the screen that shows the link to Bridge, the view options and a bit of the outline of a palette or two. I have a two monitor setup. Most of the palettes are on the auxillary monitor and they show up just fine. The main display is where I'm having the issue. I can toggle in and out of Photoshop with no display issues. I haven't tried working with anything else from the CS4 package besides InD and Photoshop. This was not an issue with any CS2 product (Dreamweaver, Fireworks, InDesign, Photoshop, Flash). Nor has it been an issue with any of the other software I am running (so far).
When the display vanishes, I can see the "data" from the program I was trying to toggle out of. For example, if I try to toggle between this page and InD right now, I can see most of this page except for the part of the page obscured by the outline of the control palette (that one reminiscent of pagemaker) and the little bits at the top. I can't see the project I'm working on. I can't see the File/Edit/etc. bar at the top of the page. A Control/Shift/Save will lock up the program completely. Then, I see the "save as" menu box (in addition to the browser screen around it) but the program is locked up. I can close everything on the computer and reboot and open InDesign to resume work--that is until I need to do something like edit a photo to drop into a layout. Then the issue occurs all over again.
Windows machine; XP Pro, service pack 3 build 2600; NVidea GeForce 9600 GT graphics card.

Bob, thanks for the info about the 6.0.2 patch. I'll try grabbing that today. This morning, on the first boot, I can't even see the program when I open it--just the snip of the command palette and part of the very top bar. Very irritating.
Peter, I have tried maximizing, closing, reopening, etc. everything else I can think of. Same issue. I finally just bit the bullet and went back to CS2, rebuilding the current project so I can get the work done by deadline. I'll look for new video drivers this afternoon after I get back on track timewise on this newsletter. Weird that this display issue should just affect the one Adobe program though, and not the others if it is a video driver problem. I didn't do a lot of work in Dreamweaver--just enough to see if it displayed the same weird behaviour. Nope. Nor does Photoshop. Nor does Bridge. Nor does Acrobat. nor does any other software on the machine.

Screen/Display Issues with Aperture 3.6 & iPhoto 9.6 on Yosemite

When I open Aperture or iPhoto, my screen goes all wonky. I have an early 2011 MacBook Pro with 8 GB Ram with the Intel HD Graphics 3000 512 MB. What is it doing this? How can I fix it?

Hello there, tehat17.
The following Knowledge Base article offers up some great recommendations for troubleshooting issues with the display on your MacBook Pro:
Apple computers: Troubleshooting issues with video on internal or external displays
Start with these:
Reset the system
You can reset the Mac's parameter RAM and SMC.
Reset the resolution
Start by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
If you tried all of these steps for your display and the video issues persist, contact Apple technical supportor take your Apple computer to the nearest Apple Store or Apple Authorized Service Provider (AASP) for diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).
Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Playbook Screen Brightness Issue

I have purchased PB few days back and I am not able to change the screen brightness. I have tried disabling the auto-din feature and tried adjusting brightness from the battery icon. The slider goes from end to end but the brightness remains the same.
Also the sliders in Settings->Screen does not even move.
Did any one else face similar issue? How can this be resolved?

on Playbook press power button and both Vol + - buttons for 10 seconds to reboot it.
and see if it persists.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Problem with 3000 N100 chargin and powering on...

For about a week now my Lenovo 3000 N100 has been having a problem powering on and charging. When it first happen I didn't notice the problem because I had a full battery, and didn't notice it wasn't charging. It wasn't until all the juice in the battery ran out that I realize this thing is messed up.
I tried swapping batteries... nothing. It won't charge either of them.
I tried changing power supplies... nothing. Still won't charge.
I can't even turn it on without a battery in it, as it will not run on AC power alone.
I know there's power getting to it because when I have a battery in plus the AC adapter, the little organge battery light on the front will blink. It blinks off and on at roughly one second intervals. When I power it on with whatever juice is left in the battery and then it dies, the battery light blinks really fast for a couple seconds and then goes back to blinking in one second intervals... not sure what this means.
I've read some stuff on here about resetting the CMOS battery. I already tried removing the AC adapter and battery and holding the power button down for 35 seconds to drain whats left in the capacitors... no go.
I even took it apart and tried to short out the CMOS battery. I think it worked because I turned it back on and when I did the BIOS told me it was reset and set everything back to fatory defaults... but then it died again.
I'm at a loss here. I got this laptop for free so I'm not afraid to just throw it away, I just don't have another one to replace it.
Any input would be appreciated.

pikkili,
Welcome to the forum.
I suggest you read through some of the symptoms described by other Lenovo 3000 N100 owners here on some of the battery discussion threads to compare your symptoms.   It sounds to be like your battery has failed. While the system can run without the battery some other users have noted that the operation may be a bit erractic, and that once the battery is replaced that the problem is solved.
At the top of the Lenovo 3000 board, you should find the annoucement and link to a tip, the tip is also linked to from the battery discussions as well. This service tip extends the battery warranty by 6 months for those affected by a particular battery issue (which it sounds like you have by the 70% charge status without the battery providing any power).    It sounds like if your system is 1.5 years old you might be near the end of this window, so best to check it out the tip and contact service soon to see if you apply.
If you are outside the window, I would recommend that you replace the battery first before spending money on diagnostics or a planar replacement.
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Tecra 9000: SD card reader will not work with XP

I have made some progress with this subject, it seems that Cardbus devices cannot share IRQs, although the main issue is that the memory address FFDFB200-FFDFB3FF is shared by both the SD card controller and the SD Card Memory Device. Unless a way to modify the registry can be found to resolve this memory conflict, the simple answer is that the SD card reader won't work under XP.
I think this would take some major surgery of the registry or re-writing of the drivers to move the memory address used by the SD card device, I am still working on this for now.
Can someone from Toshiba Support or Toshiba Marketing please explain to me why my Tecra T9100 has a sticker with "Designed for Windows XP and Windows 2000" on it, when Toshiba don't fully support XP on the 9000 series?
David
[Edited by: admin]

Hi David
Unfortunately, I dont think that you will find here someone from Toshiba marketing or other departments. This is ONLY a user to user forum.
What you say is simply NOT true.
The Tecra 9000 was delivered with 3 different OS.
It was delivered with Windows XP Pro, W2k and Win98. You can order all this Toshiba images from the Toshiba service partner. Therefore Tecra 9000 does support Windows XP!
Tecra 9100 was delivered with Windows XP and Windows 2000 and supports also Windows XP!
Of course there are different models with different hardware configuration but all supports WinXP.
I dont know why you get this error message or why you cannot use the SD card but I assume you dont use the Toshiba image. Therefore you have installed your OS not correctly. Because youre a newbie you dont know that the whole Toshiba driver installation must be done in the right order and all the Microsoft QFEs must be also installed.
As you see you have to pay attention to many important things if you want to install the OS manually.
Have a nice day

Mac Pro Screen Freezing Issue with NVIDIA 8800 GT too

There were lots of entry in threads, where the screen freezing issue was described (disorted screen with strange lines, only reboot helps). Nearly all cases seem to be related to the ATI 2600 card.
http://discussions.apple.com/thread.jspa?threadID=1358062&tstart=30
http://discussions.apple.com/thread.jspa?threadID=1365277&tstart=0
I opened this new thread to show, that this problems occurs not only for the ATI card but for the NVIDIA 8800 card, too.
My MacPro was delivered 8 days ago and was running without any problems. But all of a sudden, I got that screen freeze. And it wasn't the first time, I was heavely working 2-3 hours with that computer.
In total, 2 screen freezes showed on my computer. The first one during working with the computer. The second one during booting into MacOS X. The screen freeze occured during the boot phase with the grey screen and the spinning wheel.
My configuration:
MacPro 2.8, Dual Quad Core
6 GB RAM
3 harddisks, 1 standard from Apple, 2 Samsung with 750GB
MacOS 10.5.2
Formac 20" Monitor
Perhaps others have this problem, too? Than we should emphasize, that this is not an ATI related problem.

I've actually been having the freezing issue for a while now but I didn't have the know-how to troubleshoot it (PC tech trying to support the only Mac lab in the building).
MacPro will freeze randomly (no trend in time, system strain, or open programs). The mouse will operate but will not interact with anything.
Specs:
MacPro - Model 1,1
Dual Core Xeon 2.66
2gb RAM
nVidia GeForce 7300 GT
Mac OS 10.4.11
The machine always has 2 displays connected to it so the workaround that was discussed for the ATI 2600 doesn't apply. I had 1 display connected here in my shop and it froze for that as well.
Message was edited by: DocturKnowles

Apple Lightning to SD Card Reader no longer working with iOS 8.0.2

I just tried to copy photos from my wedding to my iPhone 5 and iPad Mini w/Retina(both with iOS8.0.2), and I get the message "This device is not supported". I find this odd, as it is the official Apple branded SD card reader.
Does anyone have any ideas as to why this would all of a sudden not be working? I had no issues prior to updating to 8.0.2.
If it is just this version of iOS, I do hope that it is fixed in 8.1.

The lightning to SD card reader has NEVER been supported on the iPhone only on iPads
Compatibility
Questions about compatibility?
Call
0800 048 0408 or Chat now
iPad models
iPad with Retina displayiPad miniiPad mini with Retina displayiPad Air
To sort the iPad suggest you restore the device especially if you did the update ovrer the air

Firefox version 22 screen tearing issue with video

So I've updated to Firefox 22 and have recently started noticing this really annoying screen tearing issue when scrolling. its only when i use Firefox sometimes it happens when I'm watching videos sometimes it just happens on normal every day pages. I've tried to duplicate this issue in other browsers (Chrome) and it just only seems to happen with Firefox. anyone else experienced this and knows how to stop it? kinda annoying

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* You can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
''Once you get the pop-up, just select "'Start in Safe Mode"''
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you.

Full screen mode - Issue with Aperture freezing

Hi I have an issue with Aperture 3 freezing if I send an image to a plug-in or external editor while in full screen dual display mode. I have to exit full screen mode first and then send to photoshop/external plugin.
It is not a huge deal and a simple workaround but if I forget to do it Aperture will freeze and I will have to force quit the application.
Any thoughts or suggestions welcome.
Thanks!

Just send a comment to Apple via "Aperture→Provide Aperture Feedback".
IME, both full-screen mode and dual-display mode have some rough edges. (I don't expect any improvements until OS 10.7, which is widely reported to include a full re-design of full-screen mode.)

Screen refresh issue with SQL Developer 1.5.5 on Vista 64 bit

I am using the latest version of SQL Developer.
I have screen refresh issues in sql developer. On scrolling up and down the display gets jumbled, some time screen do not display at all. Its making working with SQL Developer very difficult. I don't have such an issue with any of my other editors.
Is this something specific to Vista? Is there any know solution to this issue.
Thanks
Edited by: user5899685 on Sep 1, 2009 11:14 AM

Specific? Not really, but judging from the posts here Vista is more prone. It usually indicates incompatibility between Java and video drivers.
If updating your JDK or video driver doesn't work or isn't an option, just disabling DirectDraw in \sqldeveloper\bin\sqldeveloper.conf usually works too:
AddVMOption -Dsun.java2d.noddraw=trueHope that helps,
K.

Lumia 735 screen brightness issue

My new Lumia 735 has an issue with the screen brightness dimming for no reason. For completeness I have done a reset, it is nor on auto, and does I when on mains or battery. The screen is supposed to be extremely bright when set to max. However it is for about 10 secs then dims then goes bright again then dims for ages then suddenly goes bright. I have been Through all settings and changed/tried all things to no avail. I think this is not a unique problem and is prob software linked. Anyone got any ideas?

Although you say you've set the screen so the brightness is NOT set to 'auto', this sure sounds like the light sensor is still active.
I would first try a power cycle to see if that clears things up (which I doubt, but no harm trying, right?). Then do a back up and try a hard reset.
After the hard reset, test to see if the brightness is working properly. If not, then it may be malfunctioning light sensor and require repair/replacement. If it's working properly, then slowly start adding apps one by one and testing again, to see if one of them is causing the problem.
/drt

Smart Card Reader 2 syncing issue - 9 digit ID

I have a phone I am trying to set up for a customer with the BlackBerry Smart Card Reader 2. Both the phone and the card reader are running the same version of the software, as they both have the version that is installed on my desktop (5.0). However, the card reader has a 9-digit ID name, and the BlackBerry will only accept 8-digit ID information in the selected box. I've read online of people having this issue but haven't found a fix. Can anyone assist me with this problem?
BB in question is a Bold 9930 on Verizon.

Hey there,
What operating system are you currently using? Also are you receiving any error messages when trying to use the smart card reader? Have you been using only 1 smart card, or do you have a extra one handy that you could test with?
Thanks,
Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Card Reader & Screen Brightness Issues with 3000 N100 Running Fedora 10

Similar Messages

Maybe you are looking for