Cascade two WRT160N

I can't seem to get my new WRT160N to cascade with my current WRT160N.
First 192.168.1.1
I changed second to 192.168.1.2, disabled DHCP, saved.
Then plugged in a straight cat5 from lan port to lan port.
But the PC plugged into the second router, can't connect to the internet?
I tried disabling NAT, with no change, currently back enabled.
What did I miss?
Thanks

>ipconfig/all
Windows IP Configuration
        Host Name . . . . . . . . . . . . : Laptop
        Primary Dns Suffix  . . . . . . . :
        Node Type . . . . . . . . . . . . : Unknown
        IP Routing Enabled. . . . . . . . : No
        WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
        Connection-specific DNS Suffix  . :
        Description . . . . . . . . . . . : Realtek RTL8139/810x Family Fast Eth
ernet NIC
        Physical Address. . . . . . . . . : 00-16-D4-32-E0-A5
        Dhcp Enabled. . . . . . . . . . . : No
        IP Address. . . . . . . . . . . . : 192.168.1.180
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 192.168.1.1
        DNS Servers . . . . . . . . . . . : 216.185.246.1
                                            216.185.243.253
Ethernet adapter Wireless Network Connection 2:
        Media State . . . . . . . . . . . : Media disconnected
        Description . . . . . . . . . . . : Broadcom 802.11b/g WLAN
        Physical Address. . . . . . . . . : 00-14-A5-B2-7E-BC
That seems to just be the static ip on my laptop? not about the router?
thanks for the quick reply.  Gone over and over, reset after reset and can't find it.  latest firmware is installed.

Similar Messages

  • Setting up two wrt160n

    I have two wrt160n routers I want to setup on each side of a large building to get full coverage.  I can wire both two routers together or have them both wired directly to the incoming internet.  What is the recommended way to set this up and how do I configure each router?

    See my post in this thread:
    http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=108928&query.id...
    The setup for your routers is essentially the same, except you will need to set both a "wide channel" and a regular channel for each router.  Select a different set of channels on each router, and make sure that all the channels you are using are "spread apart", at least 3 channels apart (but preferably 5 channels apart if possible).

  • Can I use the PLEK500 Powerline Home Plug AV2 to cascade two EA6700 routers, plus?

    Can I use the PLEK500 Powerline Home Plug AV2 to cascade two EA6700 routers?  In otherwords, can I connect my “main router” to a PLEK500 on the third floor . . . then plug in another PLEK500 in the basement (same power lines) and use the Ethernet socket on the PLEK500 to plug into the second EA6700 in a LAN to LAN cascade?  And, if so, can I also use that second EA6700 to run an Ethernet cable to an access point at one end of the house and a different Ethernet cable underground to an out building where I can connect a third EA6700? Finally, from there to a second out building by connecting an Ethernet cable from the third router, underground again, to a 4th EA6700 in the second out building?  All connected LAN to LAN to the main router?  My problem in a nutshell: the main router is on the third floor with no way to run Ethernet cable to the rest of the house.  If I can make the first cascade via the PLEK500 to the basement router, I have access to run an Ethernet cable, via underground pipe, from the basement to the first out building and from that building to the second out building.  I need wireless access to the lower floors of the main house as well as the two out buildings.

    Yes, that is theoretically possible. You just need to make sure that you are using the same circuit for those two power lines to work. You could also refer to this link: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=83217d7598ad44d68d9cc60f1cea9887_Different_ways_in... for different ways on how to configure a router.

  • Cascade two Build Array functions - what happens?

    I found the the code shown in the attachment in a very complex VI that I am overhauling.  Would someone explain to me what is happening with the "cascaded" Build Array functions.
    I can see that the first Build Array function builds a 1D array of integers which passes to the second Build Array function which outputs a 2D array of integers but, since there is no Element or second Array input, I don't see how this works.
    This is part of a subVI that is not embedded in a loop.
     All the examples have at least two inputs.  With one input there is no Concatenate Inputs option. There is some implicit operation here that I do not understand.
    Would someone explain how this works? 
    Solved!
    Go to Solution.
    Attachments:
    Cascade two build array functions.PNG ‏7 KB

    You are taking a scalar value and creating a 1-D array with exactly 1 element.
    Then you are taking the 1-D array and building it into a 2-D array, with exactly 1 element.
    Since you can't concatenate something with nothing, the only logical mode for the Build Array would be to build it into an array of the next larger dimension.
    You could add a third one, then you'd have a 3-D array with exactly 1 element.  And so on.

  • I want to cascade two NI PXIe 5611 to make 2 upconverters statges for baseband signal

    i want to cascade two NI PXIe 5611 to make 2 upconverters statges for baseband signal

    Hello,
    Could you please elaborate a bit on the application?
    The PXIe-5611 RF Upconverter uses differential, baseband IQ signals as the input, applying quadrature modulation and upconversion to achieve a modulated RF output. If you are looking to cascade two in series, that would mean feeding a single ended RF output from the first stage into the baseband, differential IQ inputs in a second stage, which doesn't make sense to me. Perhaps we can find another solution to your application if we know some more details...
    Regards,
    Andy Hinde
    RF Systems Engineer
    National Instruments

  • Remote management thru two WRT160N's?

    Hello,
    I have two WRT160N routers.
    Router one is hooked into the cable modem, and is acting as both the router and DHCP server.
    The other (router two) is connected (wired) to router one, has the DHCP server option disabled, and is essentially acting a wireless access point.
    Router one is 192.168.1.2
    Router two is 192.168.1.3
    Remote management (over the internet) is possible for router one (at default port 8080), however I cannot get in to remotely manage router two, even with the remote management port for router two changed to 8082 and port 8082 forwarded within router one to router two (192.168.1.3).
    Anyideas?
    Thanks!

    The 2nd router is acting as a switch which is a passthrough .
    You need to make Lan to Wan connection between theses two routers .
    Enable the DHCP server for 2nd router and change ip address to 192.168.2.X
    And then forward the port on 1st router for the IP of the second.

  • Cascading two linksys routers

    I am trying to cascade my two WRT54GL routers, but can't get my second router to see internet.
    My problem:
    I want to have to separate wireless networks. One network from router 1 (main router, both wireless and wired IP "clients") and a pure wireless network from router 2. I want to be sure that the guy in 1st floor that shares my adsl connection, is using the wireless network from router 2, and dont have access to network from router 1.
    I thought I could accomplish this following alt 2 on the link:
    Cascading the linksys router to Another Linksys Router (WAN-LAN)http://www.extremepcmakeovers.com/tips/ho w-tos/cascade_linksys/ 
    My setup is:
    The main router IP. 10.104.211.197
    specified as gateaway in router seup
    DHCP server gives out IP adresser from 10.104.211.65 to 10.104.211.xx.
    I have internet connection using network from main router. All the IP clients/ consumers connected to main router has internet connection.
    So now I want to isolate the guy in first floor to another network. I have connected ethernet cable from my main router LAN to my second router WAN (internet side).Second router is specified as gateaway IP 10.104.211.70
    DHPCP server and gives out IP adresses from 10.104.211.71 to 10.104.211.xx
    Router IP adress is not taken by IP clients connected to main router, that means no IP conflict. But I can not get internet connection from second router.
    I really appreciate if someone could help me with this.

    I did get some help using live chat with linksys support yesterday. I now have internet connection from both networks. It is working now without configuration in the advanced routing tab. On both routers default values are used there (gateway and no destination IP are given).
    Here is my setup:
    Router 1= main router
    Router 2 have cable from router 1 port 3 to internet side of router.
    Router 1 is configured as DHCP server with local ip adress of 10.104.211.197, and gives out IP adresses starting from 10.104.211.64
    Router 2 is configured as a static IP with local IP adress of 10.104.210.70, and internet IP adress 10.104.211.50
    gateaway and static DNS1 is defined as the local IP adress of router 1.
    DNS2 is defined as 4.2.2.2
    Router 2 gives out IP adresses from 10.104.210.71.
    In the status tab
    Router 1 has the IP adress, gateaways, DNS1 of 193.xxxxxxxxx
    Router 2 has login type static, ip adress 10.104.211.50, default gateaway and DNS1 as local IP adress of router 1.
    So using this configuration I now have two separated networks that both can see internet. However, I have lost the internet connection several times the last 30 hours. I suspect there is something in my setup that leads to a unstable router/routers. When I loose internet connection I go to the status tab on router 1 and sees that the IP adresses are not 193.xxx but "default" values like 10.0.0.138 etc...so I then have to release and reneaw DHCP before I am online again.
    Does anyone have any clue if my setup gives poor stability???

  • Low throughput over wireless bridge with two WRT160N

    I recently bought two Linksys WRT160Ns and created a wireless bridge according to http://www.dd-wrt.com/wiki/index.php/Wireless_Bridge. I installed DD-WRT v24-sp1 (07/27/08) min.
    But, in a perfect setting where both devices are just a meter apart I can only get a throughput of 20Mbps when using security (either WEP or WPA) or 30Mbps if using no security at all. To measure this I'm transferring a large file from one computer to the other and checking the result on the "bandwidth" page of the router.
    Any suggestions on how to improve the bandwidth would be much appreciated!
    Thanks, Gordan

    Ask in a dd-wrt forum. They know how to tweak their firmware.

  • Cascading two Linksys routers questions

    wanted to clear up some things before I purchase my 2nd router.
    So currently, i have a wrt54g2 connected to my cable modem.
    What I want to do is add a wireless n router with gigabit to my LAN.
    So I would just follow the instructions on cascading the routers here: http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3733&p_created=11520...
    This makes the router a repeater pretty much and uses the same IP for the new computers, 192.168.1.x
    So my question is, if I connected to the 2nd router via LAN will I be also in the same IP range and can see the other computers on the first router?
    Reason why I'm doing this, old router hosts just normal everyday computers via wifi and lan ports.
    New router will handle htpc and media storage server via lan ports and netflix streaming via wifi.
    Thats why I want the gigabit ports, b/c there will be alot of media transferred between the htpc and media storage server.
    I'm using the wireless n for a samsung blu-ray player that can do netflix, pandora and also read shared drives.  It can read divx and h.264, so I thought the wireless n throughput will be fine on N and not bogged on g.
    any opinions and help would be appreciated.

    Yes, the second router will be in the same network range and the device which will be connected to the second router wil get the IP from the first router. To do so you need to the disable the DHCP on your second router.

  • Extending a home network with two WRT160N routers.

    Hey guys,
    I have a WRT160N and a WRT160N v2 router. I would like to extend my home network so that I have stronger bandwidth throughout different areas in my house.  Would I have to set one of these routers up as a repeater or maybe even a bridge? If so, how would I go about doing that?
    Thanks!
    -Jay-
    Solved!
    Go to Solution.

    1. If you are referring to Wireless bridging, this router's are NOT capable of that. You need to use separate wireless bridge to connect to the 2nd router;
    2. Wired bridging, though is possible. Here's the setup of that one;
    3. Instead of a 2nd router, use a wireless access point instead

  • WRT160N with WRT160N

    Hi:
     Is it possible to connect two WRT160N routers wirelessly with each other?
    I would like to expand the range and performance of my network including internet.
    I currently have WRT54G and WAP54G. Based on the multiple user reviews of the WAP4400N I am against buying it.
     Can you please explain what is Cascading and Bridging. If you have other suggestions please advise. If not, I'll have to wait unitl Linksys releases a reliable WAP-N (wish I knew how long that would take)..
    Thanks,
    Mitka

    Its not possible to connect 2 WRT160N routers wirelessly with each other.You could the WAP300N with the WRT160N router which will work fine provided you setup the wireless wide channel to 20 - MHZ channel & Standard channel being 11.Also, you do the wireless & advanced wireless settings on router...
    Difference between Cascading & Bridging..
    Cascading is using 2 routers either wired or wireless one after another...ie., NAT behind NAT.
    Bridging is wat you use 2 topologies ie., you use WRT54G & WET54G to convert the wireless signal into wired use the switch in between & send it to no of computers.

  • Late 2011 MacBook Pro running Mountain Lion - Have two external displays (one MiniDisplay, one VGA-USB), how do I rotate just the one screen?

    The primary, horizontal monitor is connected by the VGA-MiniDisplay adapter, and the secondary monitor (vertical) is connected with a VGA-USB adapter. They both connect fine, but I only have the option to rotate both at once. That is, the main 'System Preferences' window that shows up on the primary monitor has the option to rotate, but only there -- when I rotate that screen it rotates both.
    Also, I'm not going to be using the actual MacBook screen. Any ideas as to how I can get this to work? Thanks!

    The Apple TB displays I've seen come with two TB connectors. You can cascade them in daisy-chain fashion.
    However, you are limited to how much information the GPU can produce and store. I've been told by the local apple shop (not an official Apple Store) geeks that if you cascade two of the big displays onto one of the Macs (big models), both will fire up, but the Mac's internal display will be disabled. Apparently 1GB of VRAM isn't enough for so many framebuffers.

  • ADF Business Components - Cascading Tables

    I am using Oracle Jdeveloper 11.1.1.4.0
    I have tried an approach to cascade two tables using ADF Business Components.
    A single column is declared as Foreign key.
    I have used 2 drop downs. During the value change of the first drop down, the values of second sholud be populated from data base.
    How to achieve this using cascading tables.
    Kindly help.

    Hi,
    For creating cascading(dependent) LOV in adf,list of values in ADF Application using BC4J as model.please follow below links,
    https://blogs.oracle.com/aramamoo/entry/how_to_create_multi_level
    http://mjabr.wordpress.com/2011/04/01/cascade-list-of-values/
    Best Regards
    Siva Sankar

  • Modem and Cascading Routers: IP distribution?

    Hello!
    I've been searching for my case here but couldn't find anything similar. I would really appreciate your help!
    I have a Sagemcom F@st 2764 ADSL modem and two WRT160N routers.
    I want to create a network where the IP numbers are distributed by the ADSL Modem (it is now with DHCP on). To be more specific, the Modem has the IP 192.168.25.1 by default, and I want the computers connected to the Linksys routers to have 192.168.25.xxx IP ranges.
    SAGEMCOM: 192.168.25.1
    WRT160N 1: 192.168.25.2
    WRT160N2: 192.168.25.3
    Computers: 192.168.25.xxx
    Thanks!
    Solved!
    Go to Solution.

    Your 'modem' is a modem/router combo unit or Gateway.   You need to have that unit put in Bridge mode and then connect your routers.  You do not want to use the router portion of that Gateway.

  • Bridging two E2000 on different floors for ethernet cable connectivity.

    Hey guys,
    My main router is on the 3rd floor of the house.  I live on the 1st floor.  The reception isnt quite great with my old linksys so I am thinking about buying the E2000.  Im new to this so was wondering if I can buy two E2000s and bridge them together so I may get a stronger connection and be able to connect my PS3 and Seagate HD Media unit via ethernet cable. 
    Any help is appreciated. 
    Thanks! 

    Sure you can.  Go here to see how to cascade two routers.

Maybe you are looking for