Case Plastics Question

Okay so I have a Graphite FW iBook and I would like to replace the case plastics with those of a Key Lime. I really like the iBook the way it is but I think that the Key Lime is way cooler looking. (I checked out ebay to see if I could find one that I could take the plastics from, but they are going for like $500-$600, so thats out. Mainly if anyone could help with the Apple part numbers and/or where I could find decently priced parts that would be excellent, this is what I have so far:
top case: 922-5032
bottom case:
upper case/trackpad: 922-4834, 922-4816 (not sure exactly which one)
display bezel:
handle: 922-4865
hinge cap:
dvd-rom bezel:
battery door:
Thanks so much,
Storm

Have fun you will not be able to find the plastic pieces to a lime green clamshell why you ask because the lime green clamshell was a limited edition clam shell there are only 100 known still in working order this is why they are going for 500 to even 999 dollers because of how rare they are.

Similar Messages

Magsafe flashing or dim green - not charging etc. ----lower case plastic?

OK, here's a long story as short as I can make it. It will probably be confusing, as I don't have time to figure out the best organization of this info. I'm at work.
---SHORT VERSION---
What is the material attached to the lower case that the internals of the laptop are attached to made of? Does it serve a purpose other than holding down and stabilizing internals?
---REASON I'M ASKING---
I was replacing my IO/DC in board, as that is what was recommended by the Genius bar (no power with my old battery in, powered with no battery). I bought 2 other used batteries that didn't work with it either, both with supposedly over 90% health (but came shipped without much or no charge).
Anyway, last night I decided since the batteries didn't work, I would tackle the IO board. When taking it apart, I missed one of the instructions mentioning a 4mm hex head on the IO board, and broke off the bit that it screwed into of the lower case.
My question is...what is the material that the internals of the computer screw into? Is it plastic, or some sort of weak metallic material? I guess I'm asking if I could have made my problem even bigger by breaking the bit where it screws into, or if it is for "attachment" purposes only. I superglued it back on, and it stayed when I reattached the board. However, before I could get a strong green light powering up with no battery. Now it's very dim. However it will actually stay powered with a battery attached...but not charge. Sometimes it flashes, and sometimes it's dim green.
Finally (maybe), this is not a new IO board. I had to reinstall my old one, due to the fact that I'm an idiot and bought the wrong part (got an A1260 board instead of an A1211 board.) I just am worried since my symptoms have changed, that I may have created yet another problem. Now I'm waiting on another IO board, this time for A1211.
Just thought I'd see mainly if anyone knows what the material is made of.
Thanks!

Nevermind. Pretty sure it's plastic.
Turns out there was a loose connection. I'd double checked everything last night, but must have missed it as I was tired and hurrying. After it didn't worked I opened it back up and found a part that was loose, snapped it in, and it wasn't better.
Today I opened it up, and the other side of the same connector was loose. OOPS.
It now powers up like it did previously. It even started charging the battery for a few minutes, but then it quit. Still I'm relieved it's at least back to "normal" and hopefully when the RIGHT part comes, it'll work.

Vaja case ivolution question

Anyone have this case. I stumbled upon vaja's website and their ivolution looks pretty cool. I have some questions regarding that.
1. Speaker, I'm concerned when making phone calls, that hearing the conversation will be more difficult, you're ear is now farther away from speaker. I googled the ivolution for the iPhone and saw one or two complaints
2. Dust, will dust get inbetween the material and the phone? I have the incase slider now, and I take it off to clean the dust off by the seam of where the phone and the case meet
3. Pocket use, I keep the phone in my pocket, does the form factor of the iVolution inhibit this, is it too bulky?
Its a bit pricey, but its a sharp looking case, so if anyone has any thoughts or suggestions I would greatly appreciate the feedback.

I have owned Vaja cases for other products but not the iPhone. I will tell you that any case adds bulk and you will notice it. This case looks thicker then other leather cases of the past - as thick as some hard shell plastic cases.
I would think sliding it in and out of a pocket would be hard to do. You will definitely get dust around the edges and have to take it out to clean it - especially if you are slipping it into a pocket. Pockets seem to hold lint and dust.
I don't think hearing would be a problem though. Vaja makes a fine case, but i decided on none. I have gotten tired of buying accessories for every new phone that add up to more then the phone.

Free cases issue + question

I just watched the PC, and Steve said that we would receive free cases. He said that next week Apple would have a site up that allowed you to choose which case you wanted to get for free. Bumpers aren't the only ones that are being given away. There will be some other cases from other brands that will be available. This is due to the factory not being able to produce the bumpers quickly enough.
Hope that clears up some questions.
Here's a question of my own. Will we be able to input, say, an order number and be able to register for a case and have them send the case together with the phone or will we have to register after the phone is sent?

Thanks for the info!! The cheap (|) case I have does not work very well as it
comes off every time, but it works great as I haven't had too many dropped calls. Funny thing is most of my dropped calls is because I am in part of a crappy area for AT&T.

Need Help on using Forge Config Manager and CAS. Questions listed in the content below

Hi All,
I have an existing Endeca pipeline implementation where we read the data sets (Product Catalog Information) from Oracle database using JDBC adapters. The data set undergoes a series of manipulation until it gets indexed to the Endeca system. We make use of PCI for dimensions and dimension values. However, we now want to extend PCI to also include the Product catalog information. The current implementation also does not make use of CAS adapters to consume the dimensions data in PCI. The next consideration is to implement PCI as close to Out of the Box provisions and standardize it. Therefore we are also considering to implement CAS.
The questions are as below:
1. What are the ideal parameters that should support the use of PCI implementation (Dataset + dimension + precedence Rules + schema information) ? Note: We DO NOT have any product catalog system (like ATG) between database and Endeca.
2. Considering that we do not have any product catalog system to organize and maintain data, how feasible is it to read directly from database through CAS Adapters and process the data ?
3. We also plan to introduce partial update pipeline in future releases. Keeping that in mind should CAS based approach help us to read from a record store at the time of partial updates ?
4.in case we are limiting to a business case of implementing partial updates in the above explained existing design, should a custom CAS approach be a better design ? Custom CAS approach = writing the baseline output data to record store and later referring it at the time of partial updates.
5. Will CAS based approach help to reduce the baseline timings ?
6. What is the best way to export data to record store instance in the above design ? (Record store API / Command line utility / CAS crawl)
Thanks,
Nitin

Hi Neeraj,
You cam use both PI SLD and Solman Local SLD for LMDB synchronization. Now here you make to make sure that correct ranks are assigned to PI and Solman SLD. With the help of multiple sld, you can remove the cause of concern. Local SLD should always be of solman.
For CR content. that you can do for solution manager system in a click.
Divyanshu

PC 2.5: Delete cases/survey questions

Hi all,
In order to test some functionalities of PC I scheduled some surveys a few month ago.
I'm trying to delete all the questions, surveys and cases that I have created.
I tried to use program RHRHDL00 but I didn't find these attributes as parameters.
Note: i have customized lots of master data that i don't want to loose.
Any idea?
Best regards,
Julien

Julien,
I assume you are talking about a dev or QA system. It is my understanding you can't delete a question if it is in a survey and you can delete a survey if it has been used (a key control for audit purposes). That said you could go into the IMG under administration programs and "Execute Administration programs for PC workflows" and go into 'delete cases and workflows". You should be able to find whatever you want to delete in here and in theory you should be able to delete subsequent objects. I haven't done this so I'm not exactly sure if it will work. You will have to delete everything for each survey. Depending on your environment, this could be a very difficult task.
Personally, I would just mark the survey(s) and/or questions inactive and just forget about them. There are so many interdependencies on the backend that performing these types of changes might turn out to cause more trouble than they are worth. You could quickly find that other, unanticipated things go "sideways" after making manual backend workflow/case changes (like performing signoff).
Matt

Case Escalation Question

I was informed (after 7 months of various support tickets and 2 depot center repairs) that our case would finally be escalated. I was told I would be contacted early this week. It is now Thursday, and I haven't heard a peep from Lenovo since the call that resulted in the escalation last week. When do I start to worry? Is there a seperate department I should contact regarding this? We have 9 of these laptops all with the same issue and it makes us look very incompatent to our employees that are still, after 7 months, having to use these "faulty" laptops. I have heard many a horror story about Lenovo's escalation process. Any advice would be greatly appreciated.
Thanks!

Hi fat_apollo,
I hope you are doing well. I just wanted to check in and see if you still need assistance.
Please let me know and I will do all that I can to help.
All the best,
Josh Mason
Lenovo Social Media Customer Service
Want to know how to send a PM? Please go here.
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community

CAS (array) questions redux

I have a single Exchange server, where Get-Mailboxdatabase reports that the RPCClientAccessServer is servername.domain.local
I'm currently having a certificate mismatch due to using a wildcard certificate, this only manifests as an error popup when you first start Outlook. Mail works fine, as do calendars - but I want to get rid of that pop-up.
I'm already doing a split-brain DNS for EWS and so forth - mail.domain.com resolves to an internal IP internally and an external IP externally through a "real" DNS entry that's Internet-facing, and this way neither users internally or externally
get certificate errors and everything works - EAS, OWA etc. So it's just this internal issue left.
The question I have is that I read something about it being a bad idea to use the same DNS name for CAS if the same address is externally resolvable (which it would be in this case). Does setting RPCClientAccessServer affect external clients too?
Should I create a second split brain DNS entry instead, like mail-internal.domain.com and point that at servername.domain.local just to use for CAS?
The second part of this question - can I just do: Set-MailboxDatabase MailboxDatabaseName -RpcClientAccessServer “mail.domain.com” and walk away, ie skip the CAS array creation entirely if I were to choose that, assuming mail.domain.com resolves internally
to servername.domain.local?
Or should I definitely create the array and use that instead even though this is a single-server environment?
Thanks.

Indeed!
http://blogs.technet.com/b/exchange/archive/2012/03/23/demystifying-the-cas-array-object-part-1.aspx is what Will is referring to.
No, it is not that simple of just changing it and walking away.
Is this Outlook 2013 by any chance?
Cheers,
Rhoderick
Microsoft Senior Exchange PFE
Blog:
http://blogs.technet.com/rmilne
Twitter:   LinkedIn:
  Facebook:
  XING:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

TiBook 1GHz Case Repair Question

I recently noticed that the bottom case of my TiBook is coming apart a bit, right where the battery is. Basically, it's like there's nothing holding that corner of the case in place. I still have AppleCare on it, for about a month more, so I asked at my "local" Apple repair center if it could be fixed. They said that there was really no way to fix it, other than gluing it. I thought that would be a poor fix, so I declined. But I after I left, I started to think: Wouldn't that be a covered repair? If the problem is that there's a cracked plastic tab that the case is supposed to snap onto, shouldn't AppleCare replace the case part with the broken tab? Of if the problem lies with the bottom case itself, say maybe it flexed out of shape, shouldn't Apple replace it? The TiBook has never been dropped or abused, so it's not a problem that resulted from anything I did to it. Has anyone ever had a problem with a TiBook case that Apple fixed under AppleCare? I'd kind of like to know if there's a precedent for this sort of thing before I resort to Superglue.

Actually what has happened is that the titanium pan (bottom case) has separated from the plastic frame that secures it t the chassis. This part is originally glued together and I assume with some special adhesive that bonds to titanium. I would return it to apple. Likely they would end up replacing the casing rather than fixing it.

Case saving question!

Hi guys:
what is the parameter IM_NEW_VERSION(Generate New Version of Record (X: Yes/space=default: No)) of IF_SCMG_CASE_API~SAVE. Normally do we need to set the parameter?
thanks and best regards
Eric

I have two pieces of advice:
#1 Invest in some 80mm, 92mm. or 120mm case fan filters. From the pics it looks like you've got a little bit of dust in there. The filters are only like $2-$4 each at your local computer parts store (or directron.com or frozencpu.com) and you should mount them over every fan/air-intake hole in your case. The build up of excessive dust will lead to premature fan failure, I know from experience.
#2 As far as your question goes... measure twice, cut once .
[EDIT] Added URLs to filter sites.

Charger cord and macbook plastic question

First question. My charger cord seemed to get pretty hot near the connector and slowly split and melted, revealing a bare wire. Now the connection is getting flaky and I have to keep it in a certain position to keep it working. I had it replaced before, so I went into the apple store and tried to have it replaced again but was told to buy a new one as my warranty was up (which is odd because my warranty was up the last time I had it replaced). Is it safe to continue using it?
My second question is about the plastic on the MacBook. Over time a bit of the plastic has broken off the edges. I was told this was a common problem with plastic MacBooks. The person who uses it the most says she is getting shocked by the places where the plastic is missing. I don't know whether this is electricity from the laptop or just static. She says it's most commonly the a spot above the screen and sometimes to the lower right of the keyboard. Is there any way to cover these up?

1: Connect the device to Your computer and open iTunes.
2: If the device appears in iTunes, select and click Restore on the Summary pane.
Restoring > http://support.apple.com/kb/HT1414
3: If the device doesn't appear in iTunes, try using the Steps in this article to force the device into Recovery Mode.
Make sure you have the Current Version of iTunes Installed on your computer
iTunes free download from www.itunes.com/download
Note on Recovery Mode.
You may need to try this More than Once... Be sure to Follow ALL the Steps...
After you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766

CASE Expression question

Hi,
I am wondering how to implement case logic where THEN statement would be written only once for many WHEN's.
This example is from the oracle documentation, I extended it a bit.
SELECT cust_last_name,
CASE credit_limit
WHEN 100 THEN 'Low'
WHEN 200 THEN 'Low'
WHEN 5000 THEN 'High'
ELSE 'Medium'
END
FROM customers;
As you see we select 'Low' for both values 100 and 200.
What I am really looking for is something like:
SELECT cust_last_name,
CASE credit_limit
WHEN 100
WHEN 200 THEN 'Low'
WHEN 5000 THEN 'High'
ELSE 'Medium'
END
FROM customers;
OR
SELECT cust_last_name,
CASE credit_limit
WHEN 100 OR 200
THEN 'Low'
WHEN 5000 THEN 'High'
ELSE 'Medium'
END
FROM customers;
But both of selects are not valid in oracle (tested on 10g Rel2)
Maybe it is very simple and I am witting it wrong, or it is working only the way I have to repeat the THEN to every WHEN.
Thanks in advance!
let's say I would like to perform the same step

Hello
What about
tylerd@DEV2> SELECT
2      CASE
3          WHEN dummy IN('X','Y','Z') THEN
4              'Dummy is X, Y or Z'
5          WHEN dummy LIKE 'A%' THEN
6              'Dummy is like A'
7          ELSE
8              'Dummy is something else'
9      END
10 FROM
11      dual
12 /
CASEWHENDUMMYIN('X','Y'
Dummy is X, Y or ZTHTH
David

A Case Study Question in the Use of Stills with Final Cut Pro

Believe it or not, for the last week I have been reading endlessly about pixels, resolution, aspect ratio, Photoshop resizing, the bloody battle over the usefulness of the term "dpi" in video discussions, and generally about what one should do in order to use still images in a film edited in Final Cut Pro. And yet, though I have a PhD from an Ivy League university, and can understand a lot of things, I am sorry to say I am still at a loss.
Much of the discussions of photos on forums like this one are either quite technical or broadly philosophical. But my questions are completely practical and specific. I am not a photographer or a printer, nor am I an experienced editor. I am just a fairly smart person trying to use photos in his film. So I am going to ask some specific questions and hope for specific answers, without any philosophical waffling or technical mumbo jumbo.
I have one of those HP all in one printer/fax/scanner machines. I am told this device, while not fancy, is perfectly adequate to the task. Some of my photos I scan with this device from prints. Some of them I get from other people. (I have stopped downloading photos from the web, as the quality is nearly always poor.) I have Photoshop Essentials (not Photoshop). I am making a 90-minute HDV documentary, 16x9. The doc is mostly HDV footage with a still here and there. I want to be able to move on the photos (zoom, pan, etc.). I want, obviously, for them to look good. My sense is that the work flow is: (a) scan the photo (or obtain from some source as a digital file); alter the photo in some way in Photoshop; and (b) import the photo into your FCP project.
Question #1: If I have a 6x8 print, what settings should I scan it in with -- is it possible there really is no difference between scanning in it at 72dpi and 300dpi? Is it really all about the dimensions of the image? Isn't a photo whose dimensions are enlarged in Photoshop to make it available for panning and zooming in my sequence going to look fuzzier and more pixelated if it was originally scanned at 72dpi than at 300dpi? Also: Does it matter if I save it as a jpeg or tiff? Bottom line: What settings do I use in my scanning software when I scan a photo for this purpose?
Question #2: Once I have the image file on my hard drive, I suppose I now have to load it into Photoshop Elements and do something to it. What is it exactly I am using this program for? I'm going to take a wild guess. I use PS Elements to (1) crop the photo so that it has a 16x9 aspect ratio, and (2) resize it so that I can do pans and other Ken Burnsy moves on it in FCP. Bottom line: What exactly do I do in PSE to the photo and what settings do I use to both (a) make it available for moves and (b) not injure the quality of the photo by increasing its dimensions?
(In passing, I will say that I have done experiments that show that if I increase a photo's dimensions to, say, 4000 pixels by 2000 pixels, the photo's quality definitely and obviously suffers. I don't understand how a picture can be increased in size without losing sharpness. So, what am I doing wrong? Is this a function of it having been scanned in improperly to begin with?)
Question #3: If I am obtaining a photo from an outside source -- say, a professional photographer -- what are the specifications I ask for in both a hard print and a photo file? If the former, what dimensions do I ask for? If the latter, do I specify resolution and dimensions and file type?
These are my questions. At this point, I really don't want to know WHY any of this is the way it is. I just want someone to say: "Do this; do this; and then do this."
Thank you very much.

Studio X is absolutely correct; while DPI has no meaning in the video world, it often has significant meaning in scanning (and, of course, printing). If your scanning program only allows image size adjustments in DPI, then you'll have to adapt to that ... keeping in mind that the scanner's DPI setting directly relates to pixel resolution. And it is pixel resolution (not DPI) that will make all the difference in the world for images used in video. You can test this yourself by scanning an image at 1000 x 1200 @ 72 DPI and again at 1000 x 1200 at 300 DPI. They will look identical on TV or projection as long as the pixel resolution remains the same.
As an example, my Epson scanning software allows me to adjust image size by DPI or pixel resolution. Wanting to maintain the correct aspect ratio for the image area that I'm scanning, I adjust the DPI setting which in turn adjusts the pixel resolution automatically. But it doesn't work the other way around; if I adjust the pixel resolution settings manually, the DPI setting does not change. Your software may vary.
As Jim Cookman suggested, a scan setting of 300 DPI works well for most images ranging from 3 x 5 to 4 x 6 (typical snapshot size) in a DV Sequence. I may scan smaller images at 400 or 600 DPI and larger images (8 x 10 and up) at 150 DPI. Other size images fall in between those numbers. But I'm constantly watching the pixel resolution numbers to make sure I'm getting what I'll need to support the animation I intend to apply to the images once in FCP. Also bear in mind that I don't always scan the entire image. I only scan the area of an image that I intend to use in my program.
So the answer is that it all depends on your scanner's software and how far you plan to push into an image once in FCP. Do a few experiments ... you're a bright fellow so it shouldn't take long for you to find the formula that suits your purposes.
I haven't edited an HD Sequence using images yet, so I cannot offer definitive pixel resolutions for you there.
On to your specific questions:
1. See above. There is no one correct answer It all depends on what you intend to do with the image once it's in FCP. If you only plan to push in about 10%, you won't need much higher resolution than the equivalent of your FCP Sequence resolution. If you plan to push in further, you'll need a higher resolution to support that move.
2. I've been doing these for many years (SD Sequences only) and I've never loaded them into Photoshop first. I import the entire folder into FCP and drop it on the Timeline so I can see what the images look like on TV; unless your program is for CD-ROM or web delivery, that's where it counts. When you place them on the Timeline, FCP will automatically scale to your Sequence settings and pixel aspect ratio. If I see that some of them need adjustment using an external editor such as Photoshop, then and only then do I use that program. And by the way, if you have a vertical image and a 16 x 9 aspect ratio in FCP, how do you propose to crop it to fit? Perhaps you meant another term instead of "crop."
3. If it's a print, it won't matter what size they supply because you'll control the image size when scanning. If it's a file ... once again, the size (pixel resolution) depends on what you intend to do with the image once in FCP.
I really don't want to know WHY any of this is the way it is. I just want someone to say: "Do this; do this; and then do this."<<</div>
With that attitude, how did you ever earn a PhD from an Ivy League university? But if that is truly all you want, you might consider hiring an experienced editor to do it for you.
-DH

Transfer Case Animation Question Regarding if Logic.

I am using the following code in a transfer case animation and for the life of me, I can't figure out what I'm doing wrong. The "if (neutralSequence ==0)" part works great, but the "}else if (neutralSequence == 14){" part doesn't. I am using traces in each step and the value is equal to 14 when entering the function. I've attached the file and description of how to follow the sequence and it works until I get to this step.
this.neutral_mc.onPress = neutral_mc.onPress = function(){
trace ("Are you there?");
trace (_root.neutralSequence);
this.neutral_mc.onRelease = neutral_mc.onRelease = function(){
trace ("Here");
if (_root.neutralSequence == 0) {
if (needle_mc._x > 368) {
   trace ("The vehicle must be completely stopped before shifting into neutral.");
   _root.neutral_mc.gotoAndPlay ("flash");
} else if (_root.engineOff == "N") {
   trace ("The engine must be turned off before shifting the transfer case into neutral.");
   _root.neutral_mc.gotoAndPlay ("flash");
} else if ((_root.ignitionSwitchPosition == "F") || (_root.ignitionSwitchPosition == "A")){
   trace ("The igntion switch must be in the ON position before shifting the transfer case into neutral.");
   _root.neutral_mc.gotoAndPlay ("flash");
} else if (_root.held == "N") {
   trace ("Please press the Brake Hold button before shifting the transfer case into neutral.");
   _root.neutral_mc.gotoAndPlay ("flash");
} else if (shiftPosition != "N") {
   trace ("The transmission must be in Neutral (N) before shifting the transfer case into neutral.");
   _root.neutral_mc.gotoAndPlay ("flash");
} else {
   if (_root.PreviousMode != "4Low") {
    _root.gotoAndPlay ("NeutralFromTwo");
    _root.neutralSequence = 1;
    trace (_root.neutralSequence);
   } else {
    root.gotoAndPlay ("NeutralFromFour");
    _root.neutralSequence = 1;
    trace (_root.neutralSequence);
} else if (_root.neutralSequence == 14) {
_root.neutralSequence = 15;
trace (_root.neutralSequence);
_root.gotoAndPlay("Z2");
_root.neutral_mc.gotoAndPlay ("NProcComp");
Any and all help is greatly appreciated!!!

kglad,
Thanks for the suggestions, but I think the problem is in Flash. It seems that when an onRelease command occurs within the movie the code is attached to, it creates problems for the run-time engine (if that's the correct term).
I was just about to pull my hair out and thought of one other possible woraround. I created a 0 alpha movie clip above the original movie clip, then copied and pasted the EXACT code to the new movie and it worked fine.
I'm pretty new to coding and would have done a lot of things differently (more function based) if I had to do it over again but I didn't want to spend 100 hours reworking an animation that is 95% done.
I've got a lot to learn but it seems the folks at Adobe do as well. I'm sure they are aware of these limits but I doubt they're published anywhere the gen pub can see them. Perhaps they're trying to get me to purchase Suite 4?   LOL
Anyway, I really appreciate your taking the time to try to help!
Sincerely,

Case when question

Hi All,
Is it possible to use case-when statement in this SQL query?
select SUB_ID, count(T_ID),sum(TIME)
from TABLE_A
where SUB_ID <> ' '
and STARTDATE between :P6_DATE_FROM and :P6_DATE_TO
CASE :P6_FILTER_BY
WHEN '1' THEN 'and SUB_ID like :P6_FILTER_BY_TEXT || ''@%'' '
WHEN '2' THEN 'having sum(TIME) >= :P6_FILTER_BY_TEXT '
END
group by SUB_ID
as it is it seems not to work...
thanks
Liron

Hi,
Is it possible to use case-when statement in this SQL query?Yes
First of all you are using the wrong syntax of CASE.
The correct syntax is :
   CASE
        WHEN var1 = 1 THEN
                   'One'
        WHEN var 2 = 2 THEN
             'Two'
     ELSE
        'Three'
     ENDTell us your requirement we might suggest something ?
Regards

Case Plastics Question

Similar Messages

Maybe you are looking for