CAT 3750 and WCCP?
Is WCCP supported in CAT 3750?
Is WCCP supported in CAT 3750?
Hi,
Yes WCCP is supported with release 12.2 (37) SE in IP Services.Check out the below link from cisco for more information
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps5023/prod_qas09186a00801b0971.html
Hope to Help !!
Ganesh.H
Remember to rate the helpful post
Similar Messages
-
Hi all
We have a cisco network and in our smaller branch offices, are using 3750 L3 switches as the core. From this switch, we are running WCCP to a pair of WAE-674 WAAS appliances.
This is all working well, and redirection is occuring in hardware on the 3750 (running 12.2(52))
I think I know the answer to this question, but would like validation.
If we apply a redirect list to the WCCP statement in the 3750, and then put a deny in the corresponding ACL, will this deny statement be processed in hardware, or punted to the cpu? My feeling is processed software, but haven't found a rock solid cisco dodument to confirm.
thx in advance
MichaelMichael,
Considering you are running latest code, deny statement will be processed in Software, if ACL is large and has lot of hits, then you may see CPU issues on the switch. Thanks
Ahsan -
HI,
I have a 3750 as below and it doesnt seem to have eem commands on it.
I thought EEM was supported for this platform,IOS version and Package level?
Any Ideas?
Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
System image file is "flash:c3750-ipbasek9-mz.122-53.SE2.bin"Is this definitely not a defect that the CLI commands are disabled?
I have the same issue and when i look at the processes i get this:
#show process | inc EEM
9 Mwe 1CF14D8 49 971 50 7708/9000 0 EEM ED Syslog
57 Mwe 1CD7DB0 286447 1855661 154 7700/9000 0 EEM ED ND
58 Mwe 1CC7330 0 187 0 7676/9000 0 EEM ED Identity
59 Mwe 1CC7330 0 333 0 7668/9000 0 EEM ED MAT
282 Mwe 1CDE97C 0 2 0 7852/9000 0 EEM ED Routing
288 Mwe 1C82058 9 53 169 4556/6000 0 EEM Server
289 Mwe 1CA2888 0 2 0 5100/6000 0 EEM Policy Direc
291 Mwe 1CC7330 0 2 0 7820/9000 0 EEM ED CLI
292 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED Counter
293 Mwe 1CC7330 0 3 0 7820/9000 0 EEM ED Interface
294 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED IOSWD
295 Mwe 1CC7330 0 3 0 7820/9000 0 EEM ED None
296 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED OIR
298 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED SNMP
299 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED SNMP Obje
300 Mwe 1CC7330 0 3 0 7824/9000 0 EEM ED Ipsla
301 Mwe 1CEE868 0 2 0 7856/9000 0 EEM ED SNMP Noti
302 Mwe 1CC7330 11653 150780 77 7624/9000 0 EEM ED Timer
Looks like all the event detector processes are running and getting invoked. The syslog one has been invoked 971 times for example.
Does the auto smart ports feature use all of these? Also the policies are for eem 3.2 not eem 2.4 which is what is in the feature navigator. Would be really nice to be able to have cli access to these processes seeing as they are running. -
L2 redirection between a 3750 and WAE 674 WCCP
hi
we are using a WAE 674 on a cisco 3750 in WCCP
WCCP is configured to use L2 redirection
but we saw this on the switch
Global WCCP information:
Router information:
Router Identifier: 192.168.100.1
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 1
Process: 0
CEF: 1
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 11
Process: 0
CEF: 11
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
switch configuration
vlan 1 and 2 : data
vlan 3 routeurs
vlan 4 : WAE
interface Vlan1
ip address 10.0.0.1 255.255.0.0
ip wccp 61 redirect in
standby 0 preempt
standby 1 ip 10.0.0.6
standby 1 priority 150
standby 1 preempt
standby 1 name hsrp_vlan_1
interface Vlan2
ip address 10.1.0.1 255.255.0.0
ip wccp 61 redirect in
standby 2 ip 10.1.0.6
standby 2 priority 150
standby 2 preempt
standby 2 name hsrp_vlan_2
interface Vlan3
description Routage-FT
ip address 192.168.1.4 255.255.255.0
ip wccp 62 redirect in
standby 3 ip 192.168.1.6
standby 3 priority 150
standby 3 preempt
standby 3 name hsrp_vlan_3
interface Vlan4
description VLAN WCCP
ip address 192.168.100.1 255.255.255.0
WAE configuration
wccp router-list 8 192.168.100.1
wccp tcp-promiscuous mask src-ip-mask 0x1741 dst-ip-mask 0x0
wccp tcp-promiscuous router-list-num 8 l2-redirect mask-assign l2-return
wccp version 2Hi,
This counter on the 3750 is a software counter, but all WCCP redirection should be happening in hardware. Thus, it is expected the number of redirected packets to be zero or very low. The proper way to tell if WCCP is redirecting traffic to your WAE is to issue the command "show wccp gre" on the WAE and look for the line "transparent non-GRE packets received."
Example:
pdi-7341-19#sh wccp gre
Transparent GRE packets received: 0
Transparent non-GRE packets received: 28887345
Transparent non-GRE non-WCCP packets received: 0
Total packets accepted: 26012975
Invalid packets received: 0
Packets received with invalid service: 0
Packets received on a disabled service: 0
Packets received too small: 0
Packets dropped due to zero TTL: 0
----output omitted ------
Cheers,
Mike Korenbaum
Cisco WAAS PDI Help Desk
http://www.cisco.com/go/pdihelpdesk -
802.1x between Switch 3750 and ACS 4.2 Authentication faild --need help
I configured the Switch 3750 and ACS for 802.1x authentication.
when I used the windows as the 802.1x client, it prompted "click here to enter user name and pasword for the network " as normal.
The problem is that after I entered username and password (i am sure i enter the identical username and password as in ACS) the authentication failed,
What is the most possibly problem?
Thx in advance!!!
The configuration is Sw3750 is:
aaa new-model
aaa authentication login default local
aaa authentication enable default line
aaa authentication dot1x default group radius
aaa authorization network default group radius
dot1x system-auth-control
interface GigabitEthernet1/0/18
description Link to test 802.1x
switchport access vlan 119
switchport mode access
dot1x pae authenticator
dot1x port-control auto
spanning-tree portfast
radius-server host 10.1.1.333 auth-port 1645 acct-port 1646
radius-server source-ports 1645-1646
radius-server key keepopen0
In the ACS:
Network Configuration -->aaa client ip address: 10.1.119.1(the vlan 119's ip address), shared secret: keepopen0
user setup -->real name:test1, password: test1.
Attached is the debug informationWhat do you see in acs failed attempts?
-
802.1q between CAT 6500 and Passport 8600
Hi,
I`m configuring 802.1q trunking between CAT 6500 and passport 8600, in CAT 6500 I configure the port as trunk dot1q mode ON. In Passport 8600 I configure the port as TAG port.
I cretate the same vlans in both switch, but the interface vlans are create in CAT Switch. all hosts in Passport Switch that belongs to vlan 1 can ping his default gateaway (Interface Vlan) but hosts that belong to other vlan no.Please somebody helpme
-
Dear All,
Pl. tell me what all the necessary settings required for CATS, here I setup all profiles under CATS Regular and I assigned one standard workflow TS40007901 for that here my problem is
1. I entered the working times in CAT2 afer saving this it is showing an error message that workflow cannot run.
so pl, suggest me this what I can do to run this.
Regards,
Sushma.1) Use transaction PFTC
2) Select 'Standard Task'
3) Key in your Task number, in this case will be 40007901
4) Go into edit mode
5) Go to 'Default rules' tab
6) At the column 'Rule' at the row 'Agent(Default Rule)' put in the value 00000168 and check the binding checkbox.
This should do the trick.
Hope it helps. -
Comparison between 3750 and 3750-metro
hi folks,
is there any links which will provide me on the comparison between 3750 and 3750-metro? for exapmple, isis is not support on 3750 but it support on 3750-metro. The product information from cisco site is insufficient in term of the main differences :p
rgd
josh.wHi Josh,
The Cisco Catalyst 3750 Metro Series is built for Metro Ethernet access in a customer location, enabling the delivery of more differentiated Metro Ethernet services. These switches feature bidirectional hierarchical QoS and Traffic Shaping, intelligent 802.1Q tunneling with class-of-service (CoS) mutation, VLAN translation, MPLS, EoMPLS, and Hierarchical Virtual Private LAN Service (H-VPLS) support, and redundant AC or DC power. They are ideal for service providers seeking to deliver profitable business services, such as Layer 2, Layer 3, and MPLS VPNs, in a variety of bandwidths and with different SLAs.
The metro switches have the PXF chips (which allow hierarchical QoS on the 2 "WAN" GigE ports, so several logical links can share a connection, and have soft bandwidth limits).
For more details on 3750-M switches have a look at this link
http://www.cisco.com/en/US/products/hw/switches/ps5532/products_qanda_item09186a00801eb822.shtml
HTH
Ankur
*Pls rate all helpfull post -
Interconnecting Catalyst 3750 and 2948G-L3
I am trying to interconnect a Catalyst 3750 and a 2948G-L3 using fiber GBIC. The interfaces where the GBIC and fiber are attached show up as physically down. I have tried different ports and also changed both switches. No Luck. If I connect a 3524 to the 3750 using the same connection it works.
Are 2948G-L3 switches compatible with the 3750?
Thanks,
VTShould have no problem. Can you try the following on the 3750's gig interface:
speed nonegotiate
See of the link comes up.
Please rate all posts. -
Hey All,
I'm attempting to create a trunk between a 3750 and a Cisco 2811 router (with a 16 port switching module NM-16-ESW). I'm using an etherchannel trunk between the two. I'm trying to configure VTP on the 3750 (server) and make the 2811 a client. Below is a copy of the configs and output from relevant commands. Any clue why I'm not seeing vlans on the 2811?
2811 Router Config:
interface Port-channel1
switchport mode trunk
nterface FastEthernet1/14
switchport mode trunk
channel-group 1 mode on
interface FastEthernet1/15
switchport mode trunk
channel-group 1 mode on
MPLS-TEST#sh vlans
No Virtual LANs configured.
MPLS-TEST#sh vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 6
VTP Operating Mode : Client
VTP Domain Name : VTP
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xE7 0x0F 0xE8 0x89 0x47 0xAE 0x7E 0x7B
Configuration last modified by <IP of 3750> at 3-1-93 00:06:05
3750 Config and Shows:
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet1/0/47
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
interface FastEthernet1/0/48
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
sw-upstairs#sh vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 1005
Number of existing VLANs : 6
VTP Operating Mode : Server
VTP Domain Name : VTP
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xE7 0x0F 0xE8 0x89 0x47 0xAE 0x7E 0x7B
Configuration last modified by <IP of VLAN 1> at 3-1-93 00:06:05
Local updater ID is 134.178.220.224 on interface Vl1 (lowest numbered VLAN interface found)
sw-upstairs#sh vlan
VLAN Name Status Ports
1 default active Fa1/0/1, Fa1/0/2, Fa1/0/3
Fa1/0/4, Fa1/0/5, Fa1/0/6
Fa1/0/7, Fa1/0/8, Fa1/0/9
Fa1/0/10, Fa1/0/11, Fa1/0/12
Fa1/0/13, Fa1/0/14, Fa1/0/15
Fa1/0/16, Fa1/0/17, Fa1/0/18
Fa1/0/19, Fa1/0/20, Fa1/0/21
Fa1/0/22, Fa1/0/23, Fa1/0/24
Fa1/0/25, Fa1/0/26, Fa1/0/27
Fa1/0/28, Fa1/0/29, Fa1/0/30
Fa1/0/31, Fa1/0/32, Fa1/0/33
Fa1/0/34, Fa1/0/35, Fa1/0/36
Fa1/0/37, Fa1/0/38, Fa1/0/39
Fa1/0/40, Fa1/0/41, Fa1/0/42
Fa1/0/43, Fa1/0/44, Fa1/0/45
Fa1/0/46, Gi1/0/1, Gi1/0/2
Gi1/0/3, Gi1/0/4
5 INTERNET active
I'm baffled why these vlans aren't showing on my 2811. Any ideas?
Thanks,
MikeHey All,
Thanks for the input! I was actually able to solve the issue. It appears that "sh vlans" is different on an IOS router than an IOS switch. On the router it shows sub-interface ISL/dot1q trunks to a switch. This is obviously different for me as I have a switching card. In order to see VTP in action on the router and verify it was working I actually needed to view it through the VLAN database. See below:
MPLS-TEST#vlan database
MPLS-TEST(vlan)#show
VLAN ISL Id: 1
Name: default
Media Type: Ethernet
VLAN 802.10 Id: 100001
State: Operational
MTU: 1500
VLAN ISL Id: 5
Name: INTERNET
Media Type: Ethernet
VLAN 802.10 Id: 100005
State: Operational
MTU: 1500
VLAN ISL Id: 10
Name: INTERNET-DMZ
Media Type: Ethernet
VLAN 802.10 Id: 100010
State: Operational
MTU: 1500
VLAN ISL Id: 20
Name: PRODUCTION
Media Type: Ethernet
VLAN 802.10 Id: 100020
State: Operational
MTU: 1500
VLAN ISL Id: 25
Name: LAPTOPS
Media Type: Ethernet
VLAN 802.10 Id: 100025
State: Operational
MTU: 1500
VLAN ISL Id: 30
Name: NETWORK-DISTRIBUTION
Media Type: Ethernet
VLAN 802.10 Id: 100030
State: Operational
MTU: 1500
VLAN ISL Id: 250
Name: BGP-ROUTING
Media Type: Ethernet
VLAN 802.10 Id: 100250
Certainly is confusing and left me scratching my head. Thanks for the help though! I through this up on my blog too so someone in the future isn't chasing his/her tail
-Mike
http://cs-mars.blogspot.com -
Do Sales Module able to cater advertising and promotion material?
Hi all,
Can anyone tell me that if Sales Module able to cater advertising and promotion material?
How would it works?
Thanks in advance.
PompougHi,
Yes sales module can cater to advertising and promotion material.
You have to design the pricing [rocedure accordingly
If you have to give away the material free of cost then maintain condition type for discounts K004/K005/K007 as 100% Discount -
Link between 3750 and 4908 (Lx, monomode fiber)
Hello,
I have a new swtich a C3750 and a 4908 works very well.
I try to link a 3750 and a 4908, my results :
- Port of 3750 and 4908 is up when I put "speed nonegociate" . And juste few packets arrive to the 4908 and I can't ping the 4908.
- Port of 3750 is up with "speed nonegociate", and the port of 4908 stays down....
- Port of 3750 and 4908 stay down without "speed nonegociate" ... :(
You can see the 3750's config in attachments.
Ps : Sorry for my english, i'm a french student :)
Thank in advanceHi
In recent past i had tried interfacing 3750 installed with LX SFP with third party SFPs installed in Lucent DSLAMs with speed nonegotiate on the cisco 3750 side.
We did face some kinda wierd problems after the lucent DSLAMs get rebooted or sometimes even we disconnect and reconnect the fiber it happened that we failed to get the link(connectivity).
So i would suggest to go for an original Cisco SFP make to avoid all these intermittent issues which can result in unecessary downtimes..
regds -
Hello,
I seem to be having a lot of trouble with a very simple implementation. I have 2 routers and a data centre WAE via WCCP. These devices are on the same L2/L3 segment (x.x.x.0/24). The WAN interfaces on the routers are in different networks. The remote WAE is inline. I configured ip wccp 61 redirect in on the LAN interface of each router and ip wccp 62 redirect in on the WAN interface of each router. I get the alarm "WCCP router x.x.x.1(LAN) unusable for service id:61 reason redirection mismatch with router" and "WCCP router x.x.x.1(LAN) unusable for service id:62 reason redirection mismatch with router". For the WAN interfaces I get the alarm they are unreachable for the service ID.
Snadard router config
ip wccp version 2
ip wccp 61
ip wccp 62
int gi0/0
description LAN
ip address x.x.x.1
ip wccp 61 redirect in
int gi0/1
description WAN
ip address y.y.y.1
ip wccp 62 redirect in
Should I only be trapping inbound traffic on the LAN interface ?
The other thing I noticed was these messages from the PIX on the same L2/L3 segment
Dec 20 2011 05:49:52: %PIX-2-106006: Deny inbound UDP from WADMZJA02/2048 to IROUTER1/2048 on interface outside
Dec 20 2011 05:49:52: %PIX-2-106006: Deny inbound UDP from WADMZJA02/2048 to IROUTER2/2048 on interface outside
Dec 20 2011 05:49:52: %PIX-2-106006: Deny inbound UDP from WADMZJA02/2048 to IROUTER1/2048 on interface outside
Dec 20 2011 05:49:52: %PIX-2-106006: Deny inbound UDP from WADMZJA02/2048 to IROUTER2/2048 on interface outside
Access list
access-list outside_access_in extended permit udp host WADMZJA02 host IROUTER1 log notifications
access-list outside_access_in extended permit udp host WADMZJA02 host IROUTER2 log notifications
access-list outside_access_in extended permit udp host IROUTER1 host WADMZJA02 log notifications
access-list outside_access_in extended permit udp host IROUTER2 host WADMZJA02 log notifications
Best regards
Stephen
WAE config
sh run
2011 Dec 20 07:06:27 WADMZJA02 -admin-shell: %WAAS-PARSER-6-350232: CLI_LOG log_cli_command: sh run
! waas-universal-k9 version 4.3.1 (build b6 Nov 13 2010)
device mode application-accelerator
hostname WADMZJA02
clock timezone Europe/Brussels 1 0
ip domain-name fibe.fortis
primary-interface GigabitEthernet 1/0
interface GigabitEthernet 1/0
ip address x.x.x.248 255.255.255.0
exit
interface GigabitEthernet 2/0
shutdown
exit
ip default-gateway x.x.x.4 <== firewall
no auto-register enable
! ip path-mtu-discovery is disabled in WAAS by default
! <== traffic to be rerouted outbound ==>
ip route a.a.a.0 255.255.255.0 x.x.x.1 <== Outbound HSRP
ip access-list extended HK
permit ip any 0.0.0.0 255.255.255.0
exit
logging console enable
logging console priority debug
interception access-list HKWAAS
wccp router-list 1 z.z.z.202 y.y.y.122 x.x.x.1 x.x.x.2 x.x.x.3
wccp tcp-promiscuous router-list-num 1 hash-source-ip hash-destination-ip l2-redirect l2-return
wccp version 2
egress-method negotiated-return intercept-method wccp
ip icmp rate-limit unreachable df 0
directed-mode enable
transaction-logs flow enable
--More--
! [K
inetd enable rcp
sshd allow-non-admin-users
sshd enable
tfo tcp optimized-send-buffer 2048
tfo tcp optimized-receive-buffer 2048
accelerator http metadatacache enable
accelerator http metadatacache https enable
accelerator http dre-hints enable
central-manager address x.x.x.247
cms enable
! End of WAAS configurationHi Stephen,
The "Redirection mismatch" messages indicate that the redirection or return method configured on the WAE is not compatible with the router. Probably, the routers you are using don't support L2 redirection
Moving forward, I would recommend you to change the line "wccp tcp-promiscuous router-list-num 1 hash-source-ip hash-destination-ip l2-redirect l2-return" for "wccp tcp-promiscuous router-list-num 1". This will negotiate hash assignment, as well as GRE redirection and return, which are the parameters supported by most platforms.
As for the firewall messages, it seems that some WCCP negotiation packets (UDP port 2048) are being dropped. Unfortunately, my firewall knowledge is very limited, so I cannot really help you with that part.
Regards
Daniel -
We have the 3750 and 3550 switches installed at our site and we are getting the following errors.
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/13, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/13, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down
%LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/11, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/11, changed state to up
%LINK-3-UPDOWN: Interface GigabitEthernet1/0/18, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/18, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/11, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/11, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/11, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/11, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/18, changed state to down
What might be causing these errors and what can we do to fix them. Also is there some software out there that can tell us what might be causing the errors, ie... excessive collisions or the such
Thanks
SteveHere is most of the configuration for the 3750, it won't allow me to post all of it
show running
Building configuration...
Current configuration : 5733 bytes
! Last configuration change at 10:02:01 UTC Fri Sep 29 2006 by enable
! NVRAM config last updated at 10:02:01 UTC Fri Sep 29 2006 by enable
version 12.2
no service pad
service timestamps debug datetime
service timestamps log datetime
service password-encryption
service sequence-numbers
hostname CLO511204
no logging console
enable secret 5 $1$FQBc$HnhMngh.vj1ShB8AclhsX0
aaa new-model
aaa authentication login default local
aaa session-id common
clock timezone UTC -7
clock summer-time UTC recurring
ip subnet-zero
ip domain-name clovisprd
ip name-server 10.17.150.1
ip name-server 10.17.150.11
vtp mode transparent
no file verify auto
spanning-tree mode pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 150
name SWC-CONTROL
interface FastEthernet0/1
description PLC WS00-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/2
description PLC BC00-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/3
description PLC U300-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/4
description PLC P100-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/5
description PLC DRY1-00 NuCon
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/6
description PLC EVP1-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/7
description PLC DRY1-00
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/8
description PLC DRY1-10
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/9
description PLC DRY1-15
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/10
description SW PFR1-03
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/11
description PV+ PFR1-03 NotUse
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/12
description SW PFR1-02
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/13
description PLC PL20-01
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/14
description PV+ PFR1-02
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/15
description PLC IIC
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/16
description PLC angle
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
interface FastEthernet0/17
description Spare
switchport access vlan 150
switchport mode access
duplex full
spanning-tree portfast
Thanks in advance for any help you can provide -
Difference b/w item cat gr. and general item cat gr.
Hi everybody,
Can anyone plz tell me the difference between item cat group and general item cat group.
Thnx in advance....
With regards,
SubhItem category group determines the behaviour of the item,Whether it is value item or free item.
General item category group determines the category of the item ,Like trading goods,service goods or finished goods.
The item category group determines how a material is processed in the sales order. It defines, for example, that pricing does not take place for a free of charge item, such as a business gift; or that inventory management is not carried out for a service. When processing sales and distribution documents, the system uses the item category group to determine the item category. The system determines the item category based on the item category group of the material and the current business transaction, and proposes it in the respective document.
When creating the material types non-stock material and services, DIEN is proposed in both cases for the item category group, because the order processing for both material types is identical: for example, pricing is carried out for both, but no availability check.
Maybe you are looking for
-
Touch Screen Less Responsive on Right Edge with iPhone 5
So I've been having this issue with my iPhone. I actually had it replaced because of this and have the same issue with the new one. What happens is that it seems like the right edge of the screen is either intermitently or always unresponsive. Thi
-
Dear Abapers, I want to get all the records from COEP table on the basis of record selected from AFPO table. Its very very slow , some times SAP Clicked out from the report. Pl. help. In AFPO -> AUFNR field links to OBJNR field for that I have to Pas
-
Can't figure out why this won't work
Hi, I'm working on a simple app that just checks to see if a word is a palindrome. So far it works up to the point where it reverses the word, but when I run my if -else statements to check if it is a palindrome or not, it will always say it isn't ev
-
Hi SDN's I am working on 4.6C version. I have an internal table ITAB with Sales Group as one of its field. I have Sales Group SO_VKGRP on the selection screen as select-options no intervals. Now my problem is if the SO_VKGRP has some entries in the e
-
Hi , In one scenario , it is required that planned prders will be created where the req for 5- 8 days is clubed together and order date is not created on some specific day . Will lot ize key help in this regard . Regards ShankarR