Cat c6509 E with Supervisor vs-s720-10g reload and Cache error detected!

Can you help me Cat c6509-E reload
connect console I see :
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : ############################# [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASEK9-M), Version 12.2(33)SXI1, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sat 28-Mar-09 10:48 by prod_rel_team
Image text-base: 0x40101328, data-base: 0x421FFA10
Cache error detected!
CPO_ECC (reg 26/0): 0x000000B6
CPO_CACHERI (reg 27/0): 0x84000000
CP0_CAUSE (reg 13/0): 0x00004800
Real cache error detected. System will be halted.
Error: Primary data cache, fields: , 1st dword
Actual physical addr 0x00000000,
virtual address is imprecise.
Imprecise Data Parity Error
Imprecise Data Parity Error
22:12:30 UTC Tue Mar 24 2015: Interrupt exception, CPU signal 20, PC = 0x413EB310
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
-Traceback= 414EDA90
$0 : 00000000, AT : 42510000, v0 : 00000000, v1 : 00000001
a0 : 43757CC4, a1 : 00040110, a2 : 45762ECE, a3 : 00000000
t0 : 44997CF0, t1 : 00000000, t2 : D5303A40, t3 : 00003A40
t4 : 0000004F, t5 : 0000005F, t6 : 68C8F600, t7 : 00000000
s0 : BEDA4010, s1 : 00000000, s2 : 00000000, s3 : 44086D60
s4 : 45762ECC, s5 : 00000001, s6 : 00000080, s7 : 44080000
t8 : 45762ECC, t9 : 00000000, k0 : 841E6970, k1 : 02951800
gp : 4250FC60, sp : 44997D48, s8 : 4499848E, ra : 413EB310
EPC : 414EDA90, ErrorEPC : 413EB310, SREG : 3400F105
MDLO : 00159DC0, MDHI : 00000000, BadVaddr : 00000000
DATA_START : 0x421FFA10
Cause 00004800 (Code 0x0): Interrupt exception
File bootflash:crashinfo_20150324-221230 Device Error :No such device
%Software-forced reload
22:12:30 UTC Tue Mar 24 2015: Breakpoint exception, CPU signal 23, PC = 0x4171F5E0
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
-Traceback= 4171F5E0 4171D184 40F4F26C 40F4F450 40F4F670 4171282C
$0 : 00000000, AT : 42510000, v0 : 441D0000, v1 : 424C0000
a0 : 00000000, a1 : 00008100, a2 : 00000000, a3 : 00000000
t0 : 0000FF00, t1 : 3401FF01, t2 : 41712918, t3 : FFFF00FF
t4 : 41712918, t5 : 73206265, t6 : 65746563, t7 : 20546865
s0 : 00000000, s1 : 424C0000, s2 : 00000000, s3 : 08000000
s4 : 42380000, s5 : 42380000, s6 : 41D90000, s7 : 00000001
t8 : 506D5CC4, t9 : 00000000, k0 : 00000000, k1 : 00000000
gp : 4250FC60, sp : 50012420, s8 : 41D90000, ra : 4171D184
EPC : 4171F5E0, ErrorEPC : 413EB310, SREG : 3401FF03
MDLO : 00000000, MDHI : 00000003, BadVaddr : 00000000
DATA_START : 0x421FFA10
Cause 00000024 (Code 0x9): Breakpoint exception
=== Flushing messages (22:12:30 UTC Tue Mar 24 2015) ===
Buffered messages:
Queued messages:
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
Firmware compiled 19-Feb-09 20:18 by weizhan Build [100]
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Error address Lo=0x4010
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Error address Hi=0x1EDA
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Interrupt Hi reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: Interrupt lo reg=0x8000000
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-DUMP: System controller Global Registers Dump
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: global hazard reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: soft reset cfg reg=0x10FFFF
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: global cfg reg=0x20
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: init status reg=0x8
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl cfg reg=0xE
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: prio map cfg reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ecc error log reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: parity error log reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: jtag idcode reg=0x5013102F
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: work status reg hi=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: work status reg lo=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc rxstat reg=0x11FE
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc txstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: eobc mac cfg reg=0xE24
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: inbound rxstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: inbound txstat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: io int stat reg=0x408
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: pcmcia cfg reg=0x1A0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: pcmcia stat reg=0x3C
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: bist go stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: bist done stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 0=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 1=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: ibl debug reg 2=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: obl debug reg 0=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: obl debug reg 1=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: rxq debug reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: txq debug reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: gigmac cfg reg=0x1001
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-INFO1: gigmac stat reg=0x0
*Mar 24 22:12:30.667: %SYSTEM_CONTROLLER-3-FATAL: An unrecoverable error has been detected. The system is being reset.
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 24 22:12:30.695: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Mar 24 22:12:30.695: %OIR-6-CONSOLE: Changing console ownership to switch processor
*** System received a Cache Parity Exception ***
signal= 0x14, code= 0x84000000, context= 0x441ce024
PC = 0x4171295c, Cause = 0x820, Status Reg = 0x34018002
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
Autoboot: failed, BOOT string is empty
Autoboot executing command: "boot "

Hello Abubaker,
It crashed due to a parity error.
Imprecise Data Parity Error
Imprecise Data Parity Error
Which in other words means, a temporary error in memory. On single occurence adivice is to monitor the supervisor for re-occurence of such failure again. You can monitor it for 24 - 48 hours and if its a hard failure , the likelyhood of issue coming again is more and you need to replace supervisor. If it does not repeat you can consider this as a one time issue and contnue using it.
Hope this helps and please always rate useful posts.
Thanks,
Madhu

Similar Messages

Replace supervisor VS-S720-10G cisco 6509-E

Hi
I have a doubt, I have a switch core 6509-E with two supervisor. One of them has failed. So I requested for a RMA to change the part, but maybe this new supervisor is gonna have another IOS version, But I know that both supervisor has to have the same version to synch. in this case how can I load the version to the new supervisor without shut down the switch

the problem is that We dont have a memory card to copy the IOS. do you know another options?
Go to your nearest electronics shop and get one.
Take note:
Not all CF brand are supported. So it would be best to buy two or three different brands and return ones that didn't work.
Support size up to 4 Gbps.
Format the CF using the command "format disk0:" before copying anything into it.

(06 Oct 14) updated firefox and Kaspersky, now have problems with Barclays site - firefox "not responding" and plugin error on trying to close. Help!

Updated Kaspersky to 15.0.0.463(a) - ( comes with "safe money" - now turned off).
Updated Firefox from (old) version to 32.0.3.
Barclays bank site loads properly, and allows access to accounts BUT when I try to look at a statement, Firefox "not responding" and a blank/ unresponsive page is displayed.
In order to acheive any movement I have to close firefox... this gives rise to windows wanting to send error data, and Firefox apologising for loosing the tab.
None of which allows me to do essential banking transactions.
It is this machine that has the problem - I can access without problems via work computer (using google Chrome)

My guess is that your statement is a PDF document, since banks and other companies often use that format for statements.
Firefox has various options for viewing PDFs, including a built-in PDF viewer (not as full featured as Adobe's), or the option to use a plugin such as Adobe Acrobat, or to launch the PDF in an external application. This article describes how to experiment with that setting: [[How to disable the built-in PDF viewer and use another viewer]].
On another subject, your plugin list has various plugins described as "Google Chrome Extension". I haven't seen that before. Could you review the list and see whether they really should be active in Firefox or can be deactivated?
Open the Add-ons page using either:
* Ctrl+Shift+a
* "3-bar" menu button (or Tools menu) > Add-ons
In the left column, click Plugins.
For those that are not essential, I suggest changing them to "Never Activate". This might not take effect immediately in that window, but should disable them in new windows.

Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10 and 55 error

it is just a day with disaster. I bought Z77A-GD65 yesterday, and now it almost driver me crazy , i have two most famous problem of the board ,the CODE10 and ERROR 55!!!
after i bought this board to home ,i spend few hour to figure out the reason why the system can not be booted.
the DIMM SLOT 3&4 of my board is malfunction,no matter what combination i use (1&3,2&3, 3&4...etc),but it works for 1 and 2(i have 4 ram sticks,all of them is fine)
i do upgrade to BIOS 10.5(thx god ,i have two computer ,otherwise i cant even do it because of following issue)
after i solve the problem by only plug in 2 ram (DIMM1&2), succeed to boot up, a new problem occurred to me ,the CODE10!
latest driver , clean system install ,cmos cleaned, does not help.
i have read this thread for code10
https://forum-en.msi.com/index.php?topic=158591.msg1167303#msg1167303
and for error55
https://forum-en.msi.com/index.php?topic=158224.0
it seems the best way to solve it is RMA.
I notice that there is an Authorized Motherboard Repair Center (East Coast):
361 Alden Road
Markham, Ontario, L3R 3L
i live in Toronto, can i just go there and give the board to them to fix it or i can only mail it?
If i need to mail it ,what should i do?

Code 10 means the device cannot start. You have the right driver for the Intel 82579V is shorted by either a motherboard screw or a raiser under it. The ethernet adapter has lights which light up id driver is installed (even though code 10 is in effect).
Solution: Remove 1 or 2 motherboard screws and turn the pc on. Repeat until you find out which screw caused the issue. For me it was the screw closest to the ethernet controller.
The wa i fixed it was I was used a plastic washer and I was still able to have the motherboard screw in and at the same time not get code 10 anymore and my Intel 82579V worked fine since.

Firefox 16.0 and the last 15.0.1 I had issues with yahoo mail page turning fuzzy and an error message firefox is unresponsive. Page froze up and could not close

I signed into yahoo mail okay. what happens is after I open my mail the past two days all of a sudden the page would get fuzzy and I couldn't read anything or it would turn white. This never happened before and I looked at the top of the browser and it said mozilla firefox is unresponsive. I tried signing out and nothing worked. I tried minimizing the page and closing it manually and it would not let me. I tried deleting cookies and what happened it that the temporary files kept deleting for about five minutes. it was very upsetting. I have no idea what is causing this. Even when I went to control panel-internet options-delete cookies it sometimes went unresponsive. that's a first. any advise is helpful

Firefox keeps its own temporary files and cookies, separate from the ones stored by IE which you can manage through the Windows menu. If you haven't already done the following, please give it a try:
(1) Bypass Firefox's Cache
Use Ctrl+Shift+r to reload the page fresh from the server.
(You also can clear Firefox's cache completely using:
orange Firefox button ''or'' Tools menu > Options > Advanced
On the Network mini-tab > Cached Web Content : "Clear Now")
(2) Remove your yahoo.com cookies (save any pending work first) using either of these:
* While viewing a page on the site, right-click and choose View Page Info > Security > "View Cookies"
* Alt+t (open the classic Tools menu) > Page Info > Security > "View Cookies"
Then try reloading the page. Does that help at all?
When Yahoo goes blank or fuzzy moving to a different task, it may be doing some kind of animated transition. Have you noticed any graphics or font rendering anomalies?
Try disabling Firefox's hardware acceleration of graphics. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.
You usually need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
orange Firefox button ''or'' classic Tools menu > Options > Advanced
On the "General" mini-tab, uncheck the box for "Use hardware acceleration when available"
If you restart Firefox, is the issue improved?

Having the same problem with Aol not sending my mail and getting error message. If I delete this account, what will happen? This is on my iPad, and I also have a gmail and Yahoo account.

This happened after I was hacked.

If you delete that account from your iPad, all messages from it will be removed. You can then go back into Settings, then Mail, Contacts, Calendars and 'Add Account' to add it back onto your iPad.

Any help for my problem with iTunes 11.2.1 update and "unknown error (-54)"

After downloading iTunes 11.2.1 update I can't get into iTunes Store and keep getting an error message "unknown error (-54)". What does this mean? How do I correct it? No sense in having iTunes if I can't get into the store or my account.
Thank you for any help.

Why is this Itunes such a pile of junk? If I restart my computer I can sometimes find the recently added music in my Itunes Library.
It would be nice to know if other people are having the same problems.

Difference between WS-X6704-10GE or VS-S720-10G-3C 10G port

Hi All,
We have a presales case, where the partner is asking the difference between VS-S720-10G-3C and the WS-X6704-10GE linecard . He is asking from the perspective of the performance and features comparison.
I would appreciate any information that anyone would be able to provide. Thanks for the help in advance.
Awaiting your reply,
Regards
Sinu Alias

The following paper outlines deployment scenarios for the two cards if using them for Virtual Switch Links.
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps9336/prod_white_paper0900aecd806ee2ed_ps2797_Products_White_Paper.html
Brief excerpt:
âVSL-capable interfaces are required to create a VSL port channel. The current modules that support the formation of a VSL port channel are the 10 Gigabit Ethernet uplink ports on the Supervisor Engine 720-10G VSS (VS-S720-10G-3C/XL) and the Cisco 8-Port 10 Gigabit Ethernet Switching Module (WS-X6708-10G-3C/XL). (Refer to Figure 5.)
Figure 5. VSL-capable Modules
These interfaces contain new port ASICs that allow the VSH to be encapsulated on each frame forwarded out of the port and also support the ability to de-encapsulate VSH-tagged frames.â
It is a start...

6504E Aggregation Switch (VS-C6504E-S720-10G)

Hi,
I am in the process of understanding the 6504E in terms of technically feasible option as a Provider Class Aggregation Switch. (specifically looking at VS-C6504E-S720-10G, which is bundled option)
This 6504E switch will aggregate our Provider Edge (PE) routers and then connect to Core routers via uplink ports. Multiple PE routers (each via 1G port) would be aggregated to 6504E. The aggregation switch would then connect to core routers via 10G uplink port.
While short listing the aggregation switch, I come across VS-C6504E-S720-10G which has Catalyst Chassis + Fan Tray+Sup720-10G; IP Base ONLY; NO VSS. Though this looks a better choice for provider class switch .But, I am still not clear if this bundle option can support all the below requirements.
1. Multiple 1Gig/10Gig for Access/Uplink on aggregation - this is supported.
2. OIR feature for line card , modules, power supply - this is supported.
Not sure if VS-C6504E-S720-10G support all the below mandatory requirement
3. Traffic from PE will be MPLS labelled or non-MPLS labelled traffic so Aggregation Switch must have capable to look MPLS header ( i.e Lable, MPLS EXP bit) and IP header ( dscp, src SA, dst SA etc) when configured as Layer 2 port facing to PE - Not sure if VS-C6504E-S720-10G can support it.
4. Aggregation switch should support link aggregation for N*10G uplink to Core router with various load-balancing method like MPLS label based, src-IP, dst-IP, src-dst-IP, hashing of layer 3 and layer 4 info , L2 S-mac & d-mac etc - - Not sure if VS-C6504E-S720-10G can support it.
5. QOS on L2 switches for strict priority queue, WRR/SRR Queue to support policing and shaping with WRED with miinimum 8 egress queue per port.
6. QoS classification based on 802.1P, MPLS EXP, IP DSCP on layer 2 ports for MPLS and non MPLS traffic.
7. Multicast - IGMP V1/V2/V3, IGMP Snooping, PIM snooping.

Pradeep,
This is a loaded question. I would suggest you get in touch with the system engineer assigned to your company in order for him to run through all these requirements and validate that this piece of equipment meets them all.
Regards

Catalyst 6500 VS-S720-10G and VRF Capacity

Hi,
I have at the 6500 with vs-s720-10G. the datasheet say 1024 VRFs each populated with up to 700 routes/VRF for MPLS. MPLS in hardware to enable use of layer 3 VPNs and EoMPLS tunneling. Up to 1024 VRFs with a total of up to 256,000 routes per system.
I'am configurating 70 VRF with 883 routes with VRF-lite.
will it support this routes number ??
regards

With your VRF-lite deployment you described, are you planning to run any dynamic routing protocols, or are all the routes static? If you are using dynamic routing for these VRF lite instances, I would probably be worried about the number of IGP instances needed. However, maybe someone else has run a high number of VRF lite / IGP instances like that and could share their experiences.
Another concern with a 70 VRF deployment using VRF-Lite is the operational overhead, especially if you are running end-to-end VRF-lite. The Path Isolation Design Guide recommends as a rule of thumb no more than 10-15 VRF's when doing end to end VRF lite.
http://www.cisco.com/en/US/docs/solutions/Enterprise/Network_Virtualization/PathIsol.pdf
Good luck,
Matt

Replacing WS-SUP720-3B with a VS-S2T-10G

I have a remote pair of production 6509-E switches I need to replace the Supervisors in to support WS-X6716-10T-3C line cards.
Is there any easy way to replace a WS-SUP720-3B with a VS-S2T-10G, preserving the existing swtich/port configurations quickly?
Thanks
Kathie

You can most likely preserve most of the config from the existing sup720-3B and copy and paste it into the new sup-2T, but there are certain sections like the QOS config that you have to change manually, as these 2 sups have different QOS architectures.
HTH

How to use JavaMail 1.4 with Oracle Application Server 10g (9.0.4.0.0)

Hi all,
I'd like to know if it's possible and how to use JavaMail 1.4 with Oracle Application Server 10g (9.0.4.0.0), Windows version.
With the following code, I can see that the mail.jar used by the server is the one included in the jdk installation :
// I'm testing InternetAddress.class because I want to use commons-email-1.2.jar that requires mail.jar 1.4 (or higher) and activation.jar 1.1 (or higher)
// and I know that inside the commons-email-1.2.jar file, I need to call the InternetAddress.validate() method that throws a java.lang.NoSuchMethodError: javax.mail.internet.InternetAddress.validate()V if it is used with mail.jar 1.2.
Class cls = javax.mail.internet.InternetAddress.class;
java.security.ProtectionDomain pDomain = cls.getProtectionDomain();
java.security.CodeSource cSource = pDomain.getCodeSource();
java.net.URL location = cSource.getLocation();
System.out.println(location.toString());
This code returns : file:/C:/oracle/app/jdk/jre/lib/ext/mail.jar and this mail.jar file has an implementation version number: 1.2
- I've tried to include my own mail.jar (1.4.2) and activation.jar (1.1.1) files in the war file that I deploy, but it doesn't work (the server still uses the same mail.jar 1.2)
- I've tried to put the mail.jar (1.4.2) and activation.jar (1.1.1) files in the applib directory of my OC4J instance, but it doesn't work (the server still uses the same mail.jar 1.2)
- I know that a patch exists : I've read the following document: How to Make Libraries such as mail.jar and activation.jar Swappable ? [ID 552432.1]
This article talks about the Patch 6514136, but this patch only applies to : Oracle Containers for J2EE - Version: 10.1.3.3.0
Can you please help me ?
Thanks in advance for your answers,
Laurent

I strongly suggest to upgrade to AS 10.1.3 to get this.
Think of future support of AS 9.0.4. You will get not critical patch updates anymore.
--olaf

Error while trying to create new assignment with supervisor through API

Hi Experts,
I'am trying to create new assignment with supervisor for employee, but i'am facing this error:
=============================================================
ORA-20008: Error While Create new assignment..-20001
ORA-20001: The supervisor assignment that you have entered is invalid.
Please check that you have entered the supervisor,
that the supervisor assignment belongs to this supervisor and that the assignment is effective.
ORA-06512: at line 198
=============================================================
This is my script, (Oracle EBS 12.1.1)(DB 11):
DECLARE
v_user_id NUMBER;
v_res_id NUMBER;
v_res_appl_id NUMBER;
v_org_now_no_manager_warning BOOLEAN;
v_spp_delete_warning BOOLEAN;
v_other_manager_warning BOOLEAN;
v_tax_district_changed_warning BOOLEAN;
v_entries_changed_warning VARCHAR(4000);
v_person_id per_all_assignments_f.person_id %TYPE;
v_business_group_id hr_all_organization_units_tl.organization_id %TYPE;
v_people_group_id per_all_assignments_f.people_group_id %TYPE;
v_object_version_number per_all_assignments_f.object_version_number %TYPE;
v_special_ceiling_step_id per_all_assignments_f.special_ceiling_step_id %TYPE;
v_group_name pay_people_groups.group_name %TYPE;
v_ass_effective_start_date per_all_assignments_f.effective_start_date %TYPE;
v_effective_start_date per_all_assignments_f.effective_start_date %TYPE;
v_effective_end_date per_all_assignments_f.effective_end_date %TYPE;
v_assignment_id per_all_assignments_f.assignment_id %TYPE;
v_sup_assignment_id per_all_assignments_f.assignment_id %TYPE;
v_supervisor_assignment_id per_all_assignments_f.assignment_id %TYPE;
v_job_id per_jobs.job_id %TYPE;
v_grade_id per_grades.grade_id %TYPE;
v_location_id hr_locations_all.location_id %TYPE;
v_payroll_id pay_all_payrolls_f.payroll_id %TYPE;
v_pay_basis_id per_pay_bases.pay_basis_id %TYPE;
BEGIN
v_user_id := FND_GLOBAL.user_id ;
v_res_id := FND_GLOBAL.resp_id ;
v_res_appl_id:= FND_GLOBAL.resp_appl_id;
FND_GLOBAL.apps_initialize(v_user_id, v_res_id, v_res_appl_id);
BEGIN
SELECT organization_id
INTO v_business_group_id
FROM hr_all_organization_units_tl
WHERE name = 'Vision University'
AND language = 'US';
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20000,'Error While Retrieving (Business Group ID) Info...'||SQLCODE||' '||SQLERRM);
END;
FOR R IN (SELECT * FROM xx_assignment) LOOP
BEGIN
SELECT assignment_id , ass_f.object_version_number
INTO v_assignment_id , v_object_version_number
FROM per_all_assignments_f ass_f, per_all_people_f p_f
WHERE ass_f.person_id = p_f.person_id
AND ass_f.business_group_id = p_f.business_group_id
AND ass_f.business_group_id = v_business_group_id
AND p_f.employee_number = R.employee_number
AND TRUNC(p_f.effective_start_date)= TRUNC(ass_f.effective_start_date)
AND TRUNC(p_f.effective_end_date) = TRUNC(ass_f.effective_end_date);
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20001,'Error While Retrieving (Assignmet_ID) for employee..'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT job_id
INTO v_job_id
FROM per_jobs
WHERE trim(lower(name)) = trim(lower(r.employee_job))
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20002,'Error While Retrieving (Job_ID) Info...'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT grade_id
INTO v_grade_id
FROM per_grades
WHERE trim(lower(name)) = trim(lower(r.employee_grade))
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20003,'Error While Retrieving (Grade_ID) Info...'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT location_id
INTO v_location_id
FROM hr_locations_all
WHERE trim(lower(description))= trim(lower(r.employee_location))
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20004,'Error While Retrieving (Location_ID) Info...'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT payroll_id
INTO v_payroll_id
FROM pay_all_payrolls_f
WHERE trim(lower(payroll_name)) = trim(lower(r.payroll_name))
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20005,'Error While Retrieving (Payroll_ID) Info...'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT pay_basis_id
INTO v_pay_basis_id
FROM per_pay_bases
WHERE trim(lower(pay_basis)) = trim(lower(r.pay_basis))
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20006,'Error While Retrieving (Pay_Basis_ID) Info...'||SQLCODE||' '||SQLERRM);
END;
BEGIN
SELECT person_id
INTO v_person_id
FROM per_all_people_f
WHERE employee_number = r.supervisor_number
AND business_group_id= v_business_group_id;
SELECT assignment_id
INTO v_sup_assignment_id
FROM per_all_assignments_f
WHERE person_id = v_person_id
AND business_group_id = v_business_group_id;
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20007,'Error While Retrieving (Assignmet_ID) for supervisor..'||SQLCODE||' '||SQLERRM);
end;
BEGIN
hr_assignment_api.update_emp_asg_criteria(p_effective_date => TRUNC(SYSDATE),
p_datetrack_update_mode => 'CORRECTION',
p_assignment_id => v_assignment_id,
p_validate => FALSE,
p_called_from_mass_update => NULL,
p_grade_id => v_grade_id,
p_position_id => NULL,
p_job_id => v_job_id,
p_payroll_id => null,--v_payroll_id,
p_location_id => v_location_id,
p_organization_id => v_business_group_id,
p_pay_basis_id => v_pay_basis_id,
p_segment1 => NULL,
p_segment2 => NULL,
p_segment3 => NULL,
p_segment4 => NULL,
p_segment5 => NULL,
p_segment6 => NULL,
p_segment7 => NULL,
p_segment8 => NULL,
p_segment9 => NULL,
p_segment10 => NULL,
p_segment11 => NULL,
p_segment12 => NULL,
p_segment13 => NULL,
p_segment14 => NULL,
p_segment15 => NULL,
p_segment16 => NULL,
p_segment17 => NULL,
p_segment18 => NULL,
p_segment19 => NULL,
p_segment20 => NULL,
p_segment21 => NULL,
p_segment22 => NULL,
p_segment23 => NULL,
p_segment24 => NULL,
p_segment25 => NULL,
p_segment26 => NULL,
p_segment27 => NULL,
p_segment28 => NULL,
p_segment29 => NULL,
p_segment30 => NULL,
p_employment_category => NULL,
p_concat_segments => NULL,
p_grade_ladder_pgm_id => NULL,
p_supervisor_assignment_id => v_sup_assignment_id,
p_people_group_id => v_people_group_id,
p_object_version_number => v_object_version_number,
p_special_ceiling_step_id => v_special_ceiling_step_id,
p_group_name => v_group_name,
p_effective_start_date => v_ass_effective_start_date,
p_effective_end_date => v_effective_end_date,
p_org_now_no_manager_warning => v_org_now_no_manager_warning ,
p_spp_delete_warning => v_spp_delete_warning,
p_entries_changed_warning => v_entries_changed_warning,
p_tax_district_changed_warning => v_tax_district_changed_warning,
p_other_manager_warning => v_other_manager_warning);
EXCEPTION
WHEN OTHERS THEN
RAISE_APPLICATION_ERROR(-20008,'Error While Create new assignment..'||SQLCODE||' '||SQLERRM);
END;
END LOOP;
COMMIT;
END;
Thank you & Best Regards

I think this is essentially saying that the Supervisor Assignment is wrong or no longer effective. Looking at your SQL to fetch the Supervisor Assignment there are a number of potential issues. This is what you've currently got:
SELECT person_id
INTO v_person_id
FROM per_all_people_f
WHERE employee_number = r.supervisor_number
AND business_group_id= v_business_group_id;
SELECT assignment_id
INTO v_sup_assignment_id
FROM per_all_assignments_f
WHERE person_id = v_person_id
AND business_group_id = v_business_group_id;
Potential Problems/Clarifications
1. What is r.supervisor_number, what does it contain and how is it derived? I can't see that anywhere else in the block...
2. Is there a chance that r.supervisor_number is referencing an employee who has left, ie, now an ex-employee?
3. The SELECT statement that fetches the assignment_id does not perform any date-effective restrictions, which means you might be lucky enough to fetch the person's current assignment. But you might also fetch an old or future-dated assignment.
4. The SELECT statement that fetches the assignment_id does not restrict the type of assignment, so if this manager has applied for a job (ie, they have an applicant assignment) or some other type of non-employee assignment you might be picking that up.
This would work better for you:
SELECT paaf.assignment_id
INTO v_sup_assignment_id
FROM per_all_people_f papf
,per_all_assignments_f paaf
WHERE papf.employee_number = r.supervisor_number
AND papf.business_group_id = v_business_group_id
AND nvl(papf.current_employee_flag, 'N') = 'Y'
AND trunc(sysdate) BETWEEN
papf.effective_start_date AND papf.effective_end_date
AND papf.person_id = paaf.person_id
AND paaf.assignment_type = 'E'
AND paaf.primary_flag = 'Y'
AND trunc(sysdate) BETWEEN
paaf.effective_start_date AND paaf.effective_end_date;
If it doesn't return a row it means that the supervisor (or whatever employee is returned by r.supervisor_number) is not active as at sysdate and cannot be used. Note that this SQL only applies for employees. If you can have Contingent Workers as supervisors in your implementation then this needs tweaking.
Does that help?

Using Clob with TopLink 9.0.4.5 and Oracle 10g RAC

I am trying to store an XML file in a Clob type field of a DB table using TopLink 9.0.4.5 and Oracle 10g RAC and need some guidance about how to do it. I got some directions to start it with the Tip "How-To: Map Large Objects (LOBs) to Oracle Databases with OracleAS TopLink" but still need some more helps.
When using the Oracle JDBC OCI driver, the tip gives the code block for a Clob field:
DirectToField scriptMapping = new DirectToField();
scriptMapping.setAttributeName("script");
scriptMapping.setFieldName("IMAGE.SCRIPT");
descriptor.addMapping(scriptMapping);
As I understand, TopLink creates instances of the Descriptor class at run time for each of the descriptor files and stores them in a database session, where is the proper place (in SessionEvent of TopLinkSessionEventHandler?) for me to get a reference to such an instance of my Descriptor class in Java code so that I can add the above mentioned additional Mapping? Are the above String values of "script" and "IMAGE.SCRIPT" predefined in TopLink API? Can I accomplish the same thing just using the TopLink Workbench tool instead? If yes, please advise the detailed steps to do so.
The tip also states to call the following code in case of using Clob:
DatabaseLogin login = session.getLogin();
login.useStringBinding();
Should the above 2 lines of code be called after the following lines of code?
SessionManager sessionManager = SessionManager.getManager();
Server serverSession = (Server)sessionManager.getSession("MY_SESSION_NAME");
Besides the above extra coding for the Session and Descriptor Mapping, is there any special handling in between Data model and DB table mapping? Can I map a Java String type to a DB Clob field using the Direct-to-field mapping?
Appreciate any help.

Never mind ....... I had already figured it out .....

CONNECTING ORACLE 9I OR 10G DATABASE WITH ORACLE 10G FORMS AND REPORTS

pls tell how to connect oracle 9i or 10g database with oracle developer suite 10g . though the forms are getting connected but not running with error as
FRM-10142 the HTTP listner is not running on pls start the listner or check your runtime preferences.
now pls tell how to start listner and how to chage runtime preferences.
though i have worked with oracle 9i and forms 6i where we used to copy the tnsnames.ora from network/admin of oracle to forms 6i tnsnames.ora.
thank you, you may be thinking such a long question.....

sir
By server i mean the computer where oc4j and backend database are running is one one of the client pc not a dedicated server..., these database and 10g dev suite are installed in one of the client machine,
all the clients are using same internet explorer as browser.
no message is being displyed on some of the client machine where these forms are not being uploaded on browser instead it displays as done in status bar without actually showing anything at all...
sir so far as jinitiator or JRE is concered i have seen on the client machine (where my forms are running on internet explorer) a pop up is displyed telling one activex control is required to run this program and click to install it..
after clicking it download jinitiator from server and after installing jinitiator my forms are loaded and start functioning...
what i feel is as i said this machine where oc4j and database is running is one of the client machine so some other clients do not have acess to this machine, so this might be the reason why those clints are not able to run the said forms on the internet explorer.... can it be so... kindly tell..
thank you for your patience for reading the question

Cat c6509 E with Supervisor vs-s720-10g reload and Cache error detected!

Similar Messages

Maybe you are looking for