Cat Peed on MacBook, Still works but smells. HELP!

I was cat sitting for my Aunt and Uncle on vacation and one of them decided to pee on my laptop sitting on their expensive coffee table. luckily i closed my laptop and the pee only got on the outside and came right off without damage to the keyboard, motherboard, or power supply. But, IT STILL SMELLS LIKE CAT ****! I wiped it down with Lysol wipes and the smell is still present. Is there anything I can gently use to clean my laptop to get rid of this disgusting smell. I just got this thing for college, needs to last me 4 years with out my gaging.

Warm water and vinegar, you'll need to be extremely careful that no liquid enters the machine (wet the cloth, not the Mac), you will probably need to repeat this a number of times. Soft cloths (so that the Mac doesn't scratch) and absorbent tissue for blotting. Do not let it get wet, go slow.
Good luck
And once more just for emphasis .... Do Not Let The Mac get Wet!

Similar Messages

  • Mid 2010 MacBook pro took a keyboard spill.  It still works but display is sooo dark - like no backlight.  I think this is an LED screen.  Does anyone know the fix for this?

    Hi all...  My mid 2010 MacBook Pro took a keyboard spill.  It still works but the display is very very dark.  A faint image can only be seen at an angle in very bright light.  I think this model has an LED screen.  Can anyone please tell me what the fix for this is?  Thank you sooooo much! 
    < Email Edited By Host >

    Spill Cleaning
    Some liquid has just spilled into your Mac. What should you do?
    Do
    Immediately shut down the computer and unplug the power cord.
    Remove the computer's battery (if you can)
    Disconnect any peripherals (printers, iPods, scanners, cameras, etc.)
    Lay the computer upside down on paper towels to get as much liquid as possible to drip out.
    Note what was spilled on your Mac.
    Bring the computer into an Apple store or AASP as soon as possible.
    Don't
    Don't try to turn it back on. Liquids can help electrical current move about the components of your Mac in destructive ways.
    Don't shake the computer (this will only spread the liquid around).
    Don't use a hair dryer on it (even at a low setting a hair dryer will damage sensitive components).

  • Word has stopped working on my macbook air, i have used it before and powerpoint etc are all still working, but i can no longer open word or word files can anyone help?

    word has stopped working on my macbook air, i have used it before and powerpoint etc are all still working, but i can no longer open word or word files can anyone help?

    Hi Rachel,
    Have you tried reinstalling Microsoft Word? Have you tried reinstalling Office? Have you run any updates recently for Microsoft Office? There was one that came out this week. You may wish to ask this question over at the Microsoft Word forums, there's a good chance you'll get a better answer as well. This forum is primarily designed for the MacBook Air hardware and interoperability with OS X on a MacBook Air.
    http://support.microsoft.com/gp/cp_macoffice2008_master

  • My iPod 5th gen touch went through the washing machine. It still works but it has water in the screen and I can't get it out. I put it in uncooked rice for a day but it didn't work. And suggestions??

    My iPod 5th gen touch went through the washing machine. It still works but it has water in the screen and I can't get it out. I put it in uncooked rice for a day but it didn't work. And suggestions??

    Leave it in the rice for at least a day and change the rice every other day or so. The rice and iPod should be in a sealed container.
    Apple will exchange your iPod for a refurbished one for $149. They do not fix yours.
    Apple - iPod Repair price              
    A third-party place like the following maybe less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the screen yourself if you are up to it
    iPod Touch Repair – iFixit

  • The Power Supply Fan is still working, but does not appear to respond to increased loads, and its speed cannot be increased using SMCFanControl. Any suggestions?

    Hi all - My mac pro 1,1 has an enigmatic problem. It's quad-core, 3Ghz, running OS X 10.7.5. The problem began some months back, when running HD video conferences, HD streaming videos and some other graphics-moderate (I won't say intense) uses, such as slide shows in Just Looking. My machine has an ATY, RadeonX1900 card and 2 monitors - both Apple displays, one being 30 inch 2560x1600, the other being 24 inch 1920x1200.
    When I start those types of graphics-moderate apps, after about 5 minutes, something would crash (the monitors making a noise as it did) and the displays would both go black. The power did not appear to be fully cut off from the monitors. I think that the underlying applications, however, did not crash. So, I could still hear and speak to people during video conferences, and I could hear the sound tracks of videos.
    Attempts to restart the computer and get the monitors back did not immediately work to undo the problem, if done straight away. The only way to correct the problem (so as to have the monitors work) was to wait for a few minutes and then restart.
    After a lot of puzzled looking at console logs (and I confess that I am not an expert), I ran into a blank.
    But, because of the timing of the crashes (after ~5minutes use) and restarts (after some minutes wait), I reasoned that the problem might be temperature related.
    Once on that path of thought, I found this article:
    http://worldtv.com/blog/guides_tutorials/fixing_an_overheating_mac_pro_no_expens e_required.php
    I installed both Temperature Monitor and SMCFanControl. And I experimented, and got interesting results:
    Now to the puzzling bit: SMCFanControl shows that the speed of the Power Supply Fan doesn't vary much, even if I use SMCFanControl to ramp fan speeds right up. All of the other fans react to SMCFanControl, going up to and above 2500rpm when commanded. But the Power Supply Fan does not.  Having watched it for a few days now, the Power Supply Fan, according to AFCFanControl, never varies outside of a range from about 600-640 rpm, regardless of what I do with AFCFanControl.
    Also (and not surprisingly), whenever the graphics-moderate apps run, when I ramp all the fan speeds up using SMCFanControl, Temperature Monitor shows that the all of the temperatures within the machine plummet, except in the power supply locations. Power Supply Location 2 is the worst affected. Because the Power Supply Fan does not react as the other fans do, the "crashes" still occur.
    I could post some screen shots of the read outs of SMCFanControl and Temperature Monitor, although I think I have covered the key points in this post.
    It seems that the Power Supply Fan is still working, but does not respond to increased loads.
    Instinctively, I'm worried that if that's right, it might be a hard problem to fix. Any suggestions? Help! I would really appreciate them!
    Cheers
    P

    Thanks for your response Grant. I had already read about, and I think excluded, dust in graphics card/fan/assembly as a cause. The entire inside of the computer, including the graphics card/fan/assembly, is as clean as a whistle. It looks clean. I've cleaned the dust out every now and then (including a few days ago). Also, my undersanding (derived from the article, linked in my first post) is that I might expect to see high temperatures in the Northbridge and memory module B if the graphics card was overheating. According to Temperature Monitor, however, locations do not increase in temperature when I run the relevant apps. Finally, the graphics card/assembly does not feel too hot to touch.
    It is strange that SMCFanControl lists the Power Supply Fan as being software controllable, if that fan is not. Still, your comments are consistent with my observations, as the fan simply does not respond to software control.
    There are two upsides: First, I've something of a work-around. I've worked out what temperature must be achieved in Power Supply Location 2 for a crash to occur, and I can watch that location in Temperature Monitor, terminating the process before that treshold is reached. Of course, that's not ideal. Second, ramping all the other fans up does significantly delay the onset of the problem, and makes recovery time much quicker.
    Is there any donwside to peridically ramping up the other fans when running the relevant apps? Given that it causes all of the other locations to cool significantly, could this lessesn the life expecancy of the mahcine? (I don't want to run the fans up all the time - that's like sitting next to a jet ready for take off!)
    Also, a correction to my first post: Yesterday, with all the other fans running on full and running an HD streaming video, the Power Supply Fan did, eventually, slowly, come up to ~740rpm, which is much higher than the ~640rpm maximum I had previously seen, and this may have aided delaying the onset of the problem. 
    I'm not sure where this leaves me? The problem might now be able managed. Well, sort-of. But it's not eliminated.

  • After installing Leopard, my G4 will no longer boot in OS 9.22. (Classic still works, but I need it to boot in OS 9.)  Any clues about what the Leopard installer might have done to my machine that rendered OS 9 boot unusable? What can I do to fix it?

    After installing Leopard, my G4 will no longer boot in OS 9.22.
    (Classic still works, but I need it to boot in OS 9.)
    Any clues about what the Leopard installer might have done to my machine that rendered OS 9 boot unusable? (And what can I do to fix it?)
    Details:
    G4 Gigabit Ethernet
    Boot ROM version: 4.2.8fl
    Accelerator card added: 1.6 MHz
    1.5 Gig Ram
    I have erased the partition that had Leopard installed on it.
    I zapped the pram.
    In Open Firmware, I "reset-nvram", and then "reset-all"
    I tried to reinstall G4 FW Update 4.2.8, but that must be done when booted from OS 9, and of course, that's the problem: it won't boot into 9.
    I tried restarting from 9.2.1 DVD.
    I tried restarting from an external firewire drive containing OS 9.2.2.
    I tried moving a fresh OS 9.2.2 system folder into an empty partition on an internal hard drive. (Partition was created WITH OS 9 drivers installed.)
    All attempts to boot into OS 9 give me the same results - grey screen - no spinning beach ball, no icons or logos - just a blank grey screen.
    This machine still works fine in OS 10.3 and 10.4, and it worked fine for many years booting into OS 9, until I installed Leopard, and I haven't been able to boot into OS 9 since then, although I have done considerable research online and tried many things.
    I have since learned that this machine does not support Leopard - 10.5. Fine, but how did it break 9.2.2?
    Any help greatly appreciated.

    Thanks for checking in, BDAQua.
    Problem solved.
    In the docs that came with my Powerlogix accelerator card, I found this sentence buried:
    "If you reset the PRAM, the NVRAM code for OS9 compatibility is cleared, so you will have to boot from the Firmawre Update CD and perform this process again in order to boot in OS9."
    The "process" it's referring to is the process of setting up the NVRAM for booting into OS9 from the CD.
    Fortunately, I was able to find the disk, and it worked as expected. I can now, once again boot into OS9.
    Conclusion: My (unadvised) attempt to load Leopard on this old machine apparently reset the PRAM on the accelerator card and cleared the NVRAM code for OS9 boot. Although I did attempt to reset the NVRAM via Open Firmware, it did not reset it on the accelerator card.
    So, thank you BDAQua, for your "Ah yes" . . . that's all I needed to steer me in the right direction.
    Gratefully,
    tupester

  • I tried updating my iPhone3g through itunes. Now i'm stuck in recovery mode and i've EVERYTHING even websites and such but nothing worked out! I've also tried restarting and fiddling with the home button but nothing still worked. Please help!

    I tried updating my iPhone3g through itunes. Now i'm stuck in recovery mode and i've EVERYTHING even websites and such but nothing worked out! I've also tried restarting and fiddling with the home button but nothing still worked. Please help! What should I do??

    Well, if you've indeed tried EVERYTHING, then you'll need to bring your phone to Apple for evaluation.

  • I am running Mac OS X Lion on a brand new Mini.  Every now and then, my keyboard goes "dead."  The mouse still works but can't type.  If I restart, everything is fine again.  Is there anything that will fix this problem?

    I am running Mac OS X Lion on a brand new Mini.  Every now and then, my keyboard goes "dead."  The mouse still works but I can't type.  If I restart, everything is fine again.  Is there anything that will fix this problem?
    Also, I am trying to connect my Mini from the mini-Displayport to the Displayport of my Dell U2410 monitor.  The image is very grainy,even though it is set to the correct resolution: 1920 X 1200 at 60Hz.  If I use HDMI to VGA input, the image is much clearer.  Is there a way to get the Displayport to work?

    I'm having exactly the same keyboard issue.  Certainly nothing has ever enhanced my concentration while coding like suddenly becoming unable to type.
    I'm seeing a great many devicemgr and rake errors in my system log.  I don't know if they're related.  How 'bout you?
    If you're unfamiliar with the system log…
    Open /Applications/Utilities/Console.
    If necessary, choose View > Show Log List.
    system.log is at the top of the FILES section.
    Try searching it for hot words like DEBUG, FATAL, and aborted.
    I've found some discussions that would tend to indicate my errors are postGres related – I'm running OS X server.
    -Bryan

  • I dropped my iphone and the screen has blue lines on it. Siri still works but the screen doesn't but the screen isn't cracked or shattered. What should I do?

    I dropped my iphone and the screen has blue lines on it. Siri still works but the screen doesn't but the screen isn't cracked or shattered. What should I do?

    Bring your phone and $199 to the Apple store for an out of warranty exchange of your phone.  You clearly broke it when you dropped it.

  • After I upgrade maverick my display will suddenly shut off but my sounds is still working. Need help

    After I upgrade maverick my display will suddenly shut off but my sounds is still working. Need help on this? Thank you

    Hello rodamitjr,
    It sounds like your iMac display will turn off unexpectedly, but you can tell the computer is still on because you hear audio.
    I found an article with steps to troubleshoot issues with displays.  This article is for internal and external displays, so you can skip any steps referring to an external display.  I recommend reviewing the full article, but this step specifically stands out to me for the issue you described:
    Reset the system
    You can reset the Mac's parameter RAM and SMC.
    You can find the full article here:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Thank you for posting in the Apple Support Communities.
    Best,
    Sheila M.

  • I cracked my screen for my touch, it still works but the cracked is big and annoying . I'm still under warranty, will they fix it still?

    I cracked my screen for my touch, it still works but the cracked is big and annoying . I'm still under warranty, will they fix it still?
    It works fine. Some of my album covers are mixed up though, not sure its because of the fall. help me

    It is very unlikely that Apple with replace your iPod under warranty since the warranty covers manufacturing and design defects. A crack screen is usually not caused by a defect.  You can alway make an appointment at ter Genius Bar of an Apple store and ask.

  • Dragon swipe still works but won't display any emoticons

    After the update a couple of days ago, my dragon swipe still works but won't display any emoticons or special characters, anyone have this problem or know how to restore the special characters?
    Subject line condensed by: Verizon Moderator <<>>

        Let's look further into this Quinta53! Have you tried powering the device off/on? If so, try clearing the application cache here http://vz.to/1hC0A2D test and share. Thank you.
    TominqueBo_VZW
    Follow us on Twitter @VZWSupport

  • I have low battery on my ipad and it still works but it is not fully charging what can i do

    i have a low battery on my ipad it still works but it is not fully charged what can i do to fully charge it

    Clean the charging port.
    Charge using the supplied wall charger, not your computer.
    Try another charger and/or cable.
    If none of these work, you have a hardware problem.

  • I have my iPod touch 5g and the home button is stuck , it still works but its stuck so I have to push hard for it to work, I still have my warranty , will apple replace the iPod ?

    I have my iPod touch 5g and the home button is stuck , it still works but its stuck so I have to push hard for it to work, I still have my warranty , will apple replace the iPod ?

    Make an appointment at the Genius Bar of an Apple store. If the iPod is defective and not abused Apple will exchange it at no cost
      Apple Retail Store - Genius Bar

  • HT1353 I have a Ipod mini 6gb that still works but a new computer that doesn't have its software.  How can I download the software for it

    I have a Ipod mini 6gb that still works but a new computer that doesn't have its software.  How can I download the software for it

    Check the iPod Hardisk health with the iPod  Disk Diagnostic, as posted by tt2
    https://discussions.apple.com/message/17776595#17776595
    It wont fix your problem, but may tell help troubleshoot, why it is freezing iTunes, especially when the Pending and Realloc numbers are high.
    have a nice day!

Maybe you are looking for